Euro-Pro PURSUIT UV209B User's Manual
Contents
1. 3 Remove the hose connector from the rear of the unit and push in the desired attachment firmly onto the end of the hose 4 If additional length is required attach the extension tubes to the end of the hose and then attach the crevice tool round brush or upholstery brush to the end of the extension tube Warning Avoid tipping the vacuum or setting it on furniture fringed area rugs or carpeted stairs while you are using the hose with the attachments When using the unit to vacuum floors or with attachments set the Carpet to Floor Selector to the Floor position This will stop the beater brush from rotating When vacuuming carpets avoid leaving the vacuum in one place for an extended period of time particularly on thick carpet Caution Do NOT pull the vacuum cleaner around the room by the hose as it could tip over and cause damage When using the attachments do NOT over extend the hose length when reaching Trying to reach beyond the hose reach could cause the vacuum to tip over How to Start The upright vacuum can be used on multiple types of carpeting bare floors or upholstery with attachments When using the attachment tools such as the crevice tool round brush or the upholstery brush place the handle of the vacuum in the upright position 1 Turn the quick release cord holder to either side 180 to release the power cord 2 Plug the power Cora nio We electrical outlet or 3 Push the On Off button to2. of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks Occasionally the power nozzle drive belt will require changing the frequency will depend upon the amount of use your vacuum sees 1 Turn the vacuum Off and unplug from power supply 2 Turn the vacuum upside down on a flat level surface 3 With a coin or a thick flat head screwdriver unlock the two 2 screw locks by turning counter clockwise Fig 21 e el i 4 Remove the bottom cover of the power head 5 Lift the right side of the agitator brush first and then lift the left hand side and iM D agitator brush out of the power ead 4 R E the bottom cover of the power ead 5 Lift the right side of the agitator brush first and then lift the left hand side and lift the agitator brush out of the power head Carefully remove any belt residue that may exist in the belt area 7 Ifthe belt has broken remove any loose pieces before replacing with a new belt Remove the worn or broken belt from the motor drive shaft Loop the new belt first over the motor drive shaft and then over the agitator pulley Fig 22 a o Fig 22 10 Insert the left side of the agitator in first by placing the end cap down into the slot and then do the same with the right side Press firmly to make sure that each end is completely ins
3. on wet surfaces unplugging vacuum cleaner into Do NOT allow children to use as a toy electrical outlet Close attention is necessary when used 15 Use extra care when vacuuming on by or near children stairs Use only as described in this manual Use 16 Do NOT pick up flammable or only manufacturer s recommended combustible materials lighter fluid attachments gasoline kerosene etc or use in the Do NOT use with damaged cord or plug presence of explosive liquids or vapor Do NOT use vacuum cleaner if it has been 17 Do NOT pick up toxic material chlorine bleach ammonia drain cleaner etc 18 Do NOT use in an enclosed space filled with vapors given off by oil based paints paint thinner moth proofing Do NOT pull or carry by cord Do NOT use substances flammable dust or other cord as a handle close a door on cord explosive or toxic vapors or pull cord around sharp edges or 19 Use only on dry indoor surfaces corners Do NOT run appliance over cord 20 Do NOT use for any purpose other Keep cord away from heated surfaces than described in this user s guide dropped damaged left outdoors or dropped into water Return appliance to EURO PRO Operating LLC for examination repair or adjustment Do NOT unplug by pulling on cord To 21 The use of an extension cord is not unplug grasp the plug not the cord recommended Do NOT handle plug or vacuum cleaner 22 Do NOT put any objects into openings Do NOT use with
4. power cord into an electrical outlet until the vacuum is fully assembled Handle Assembly 1 Carefully unpack all components set aside packaging 2 Lift vacuum body to upright position 3 Remove the screw 1 that comes attached to the body 4 From the rear of the vacuum align m the handle with groove and slide onto vacuum If necessary use thumb and finger Fig 1 pressure to slide handle into position 5 Once handle is in place secure the handle with the screws 2 Fig 1 Caution Do not over tighten Over tightening could strip the screw holes Do not operate the vacuum without the handle screws in place Cord Assembly 1 Make sure that the quick release cord holder is in the upright position 2 Remove the wire tie from the power cord 3 Wrap the cord into place by wrapping it in a clockwise direction around the quick release cord holder and the lower cord holders Fig 2 oriental 4 Turn the quick Fig 2 release cord holder to the left or to the right to unwrap the power cord Fig 2 Warning Always make sure that the vacuum is turned off before unplugging Using the Attachments 1 Place vacuum in its upright position Make sure that the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories 2 Turn the carpet height selector to the highest position and set the Carpet to Floor selector to the Floor position
5. 6 987 4275 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time or visit our website www sharkvac com FOR TECHNICAL SUPPORT for Model UV209B Call 1 800 798 7398 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time Please Note Pre Motor Secondary and Exhaust Filters are washable They should however be replaced every three 3 months to ensure peak performance of your vacuum The HEPA Dust Cup Filter may be washed We recommend washing it once a month or when suction appears to be reduced To wash your HEPA Dust Cup Filter hold filter cartridge by frame flange and rinse under a tap until all observable dirt has been removed Some discoloration of the HEPA filter material may occur this is normal and will not affect the filter s performance When finished shake off excess water Do NOT wash in dishwasher It is important that when you wash the HEPA dust cup filter pre motor filter or the exhaust filter you allow them to dry COMPLETELY before using again We recommend 24 hours to air dry DO NOT DRY IN DRYER Important Make sure that ALL washable Filters are completely dry before inserting back in the vacuum 10 OPERATING INSTRUCTIONS Changing the Headlight Bulb Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks 1 Turn unit Off and unplug f
6. Model UV209B EURO P R Ox ONE 1 YEAR LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of the original purchase This warranty applies only to normal domestic household use Should your appliance fail to operate properly while in use under normal household conditions within the one 1 year warranty period contact EURO PRO Operating LLC Customer Service at 1 866 98SHARK 1 866 987 4275 for information on returning the appliance and accessories If the appliance is found by EURO PRO Operating LLC to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date and 16 95 to cover the cost of return shipping and handling must be included Non durable parts including without limitation drive belts rotating brushes bulbs and electrical parts which normally require replacement are specifically excluded from warranty The liability of EVRO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects cau
7. ONSUMERS ONLY Please fill out and mail the product registration card within ten 10 days of purchase in order to validate the foregoing Limited Warranty The registration will enable us to contact you in the unlikely event of a product safety notification By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions RETURN TO EURO PRO Operating LLC Canada 4400 Bois Franc St Laurent QC H4S 1A7 Model UV209B Appliance model Date purchased Name of store Owner s name Address City Prov Postal Code Printed in China 11 Shark Ursuit CYCLONIC BAGLESS UPRIGHT OWNER S MANUAL Model UV209B 120V 60Hz 12 Amps EURO PRO Operating LLC Tel 1 866 98SHARK 1 866 987 4275 www sharkvac com EURO PROX IMPORTANT SAFETY INSTRUCTIONS When using your Bagless Upright Vacuum basic safety precautions should always be observed including the following WARNING To reduce the risk of fire electrical shock or injury 1 10 11 12 13 Do NOT use without filters in place Use ONLY filters and accessories provided by EURO PRO Operating Do NOT leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and before LLC Failure to do so will void the removing filters warranty To reduce the risk of electric shock do 14 Turn off all controls before plugging or NOT use outdoors or
8. amage the vacuum F GETTING TO KNOW YOUR CYCLONIC BAGLESS UPRIGHT A n MA A ANNI ye yy Mi S gt 1 Upper Handle 10 Flexible Hose 2 On Off Switch 11 Power Cord 3 Dust Cup Release Button 12 Quick Release Power Cord Holder 4 Dust Cup 13 Round Brush 5 HEPA Filter Frame 14 Upholstery Brush 6 Carpet Height Selector 15 Crevice Tool 7 Furniture Guard 16 Extension Tubes x2 8 Head Light 17 Hose Connector 9 Motorized Power Head 18 Carpet to Floor Selector Technical Specifications Voltage 120V 60HZ Power 12 Amps Note Illustrations may differ from actual unit OPERATING INSTRUCTIONS Motor Thermostat Important This unit is equipped with a motor protective thermostat If for some reason the vacuum cleaner should overheat the thermostat will automatically turn the unit off Should this occur e Push the On Off button once e Disconnect the plug from the power source e Check the source of overheating problem i e clogged hose or filter e If clogged hose or filter is found unclog the hose and replace the filters e Wait at least 45 minutes before attempting to reuse the vacuum After unit has cooled down for 45 minutes plug in the cleaner and push the On Off button The vacuum should start again e If the vacuum still does not start contact customer service at 1 800 798 7398 Cleaning amp Changing the Belt Warning To reduce the risk
9. any opening blocked Keep free of dust lint hair and anything else that may reduce air flow with wet hands Do NOT use the vacuum cleaner to pick up large objects or objects that are likely to damage the vacuum cleaner 23 Store your appliance indoors in a cool Keep hair loose clothing fingers feet and dry area all parts of body away from openings 24 Keep your work area well lit 25 Do NOT immerse the vacuum into rotating agitator and other moving parts water or other liquids Do NOT operate cleaner in bare feet or when wearing open toe shoes 26 Keep end of hose wands and other Do NOT pick up hot coals cigarette butts openings away from your face and matches or any hot smoking or burning body objects 27 To avoid damaging the carpet keep Do NOT pick up hard or sharp objects the vacuum cleaner head moving at all such as glass nails screws coins etc times SAVE THESE INSTRUCTIONS For Household Use Only WARNING To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do NOT modify the plug in any way 1 Rev 01 04 EURO PROX Powe BAGLESS UPRIGHT TO ORDER REPLACEMENT FILTERS OR BELTS for Model UV209B Call 1 866 98SHARK 1 86
10. ath the HEPA filter there is a o secondary filter ies This is washable in a ae lukewarm water a Fig 14 We y recommend washing L it when you are ETA washing your HEPA filter i Always allow the secondary _ filter to air dry for 24 hours before replacing into the gE y vacuum Never run cart the vacuum without Fig 14 the secondary filter in place
11. erted 11 Check to make sure that the belt is centered on the pulley and that the agitator turns freely 12 Replace the top cover over the power head base and lock in place by turning the two screw locks clockwise until you hear them lock in place OPERATING INSTRUCTIONS Changing amp Cleaning the Pre Motor Filter Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The pre motor filter is located in the vacuum underneath the dust cup Please note that this filter is a washable filter and can be cleaned by rinsing under lukewarm water Always allow the pre motor filter to air dry for 24 hours before replacing in the vacuum Do not use a hair dryer to dry it Air dry only To remove the pre motor filter 1 Remove the dust cup ee instructions on page 5 for removing the dust cup 2 Hold the Pre Motor filter cover and turn counter clockwise to unlock and lift to remove Fig 15 3 Remove the pre motor filter and clean by rinsing under lukewarm water 4 After air drying for 24 hours replace in the vacuum 5 To replace the pre motor filter cover insert the locking lugs into oe holes and turn clockwise to ock Pre Motor SSN Filter Cover Changing amp Cleaning the Exhaust Filter Warning To reduce the risk of electric shock the power cord must be disc
12. fore removing the dust cup dust cup filter changing the filters or performing maintenance trouble shooting checks The Dust Cup must always be emptied when the dirt level reaches the FULL line on the dust cup To remove the dust cup from the vacuum 1 Press down on the dust cup release button that is located on the handle of the dust cup Fig 6 2 Holding the dust cup from the handle pull the dust cup out from the vacuum Fig 7 3 To empty the dust cup hold it by the handle over a garbage can and press on the trap door release button to empty Fig 8 i ae l og hk PLease Trap Door Release OPERATING INSTRUCTIONS Cleaning the HEPA Dust Cup Filter IMPORTANT Please Note The Rinseable TapClean HEPA Dust Cup Filter will stop most of the tiniest dust particles and airborne allergens from re entering the air you breathe In fact it stops 99 97 of all particles as small as 0 3 microns many times smaller than a human hair Because of this incredible filtration performance the HEPA Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power if not cleaned properly Clean the HEPA Filter after each use as described in this section 1 To remove the HEPA filter remove the dust cup from the unit 2 Toremove the dust cup cover hold the cover by the hand
13. le turn counter clockwise and lift the cover off Fig 9 3 Remove the HEPA Rinseable Tap Clean filter from the dust cup Fig 10 4 Vigorously TapClean the HEPA dust cup filter on a hard surface until no more dust is observed falling out Fig 11 The HEPA filter may also be washed by running it under the tap allowing the water i to run on the dirty side gah Fig 12 We A recommend washing H r it once a month e or when suction appears reduced Always allow 24 pA hours for air drying before Sp replacing into the vacuum Fig 10 Please Note The white material in the HEPA filter will discolor over time This is NORMAL and will NOT affect the performance of the filter Warning Always empty the dust cup and clean the HEPA dust cup filter before each use and during prolonged usage Never over fill the dust cup remove dirt and clean the HEPA dust cup filter each time the dust cup is emptied during prolonged usage or risk motor damage Cleaning the HEPA Filter Frame 1 Before replacing the HEPA filter in the HEPA Filter frame you can should rinse the frame in lukewarm water by just running it under the tap to remove any dust that is adhering to the frame Fig 13 Do NOT place in dishwasher peas Fig 13 2 Make sure that the filter frame is completely dry before replacing into the dust cup Always air dry for 24 hours Cleaning the Secondary Filter 1 Underne
14. onnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The exhaust filter is located on the front of the unit below where the dust cup is To remove the exhaust filter you must first remove the filter cover 1 Check the exhaust filter frequently and replace with new filters when dirty 2 Remove the exhaust filter cover Fig 16 Remove the exhaust filter Rinse in lukewarm water and let the filter air dry for 24 hours before re installing into the vacuum Do not use a washing machine to rinse the filter Do not use a hair dryer to dry the filter Air dry only Never operate the vacuum without ALL the filters in place 5 When the filter is dry replace into the vacuum and replace the filter cover Note A severely soiled or clogged filter should be thoroughly washed with fresh tepid water A mild detergent may be used if required TEO Cleaning the Dust Cup Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The dust cup can be washed in lukewarm water Do not use strong detergents Ensure that the dust cup is fully dry before putting back on the vacuum cleaner Fig 17 Do not wash in dishwasher OPERATING INSTRUCTIONS Assembling Your Vacuum Cleaner Note Do not plug the
15. rmostat page 8 Reset circuit breaker or replace fuse Clean dust cup page 5 Adjust setting page 5 Remove obstruction Remove power head cover and remove obstruction Remove obstruction Replace belt page 8 Push hose in securely Clean change filters page 6 7 Adjust setting page 5 Replace belt page 8 Check belt changing and agitator cleaning page 9 Check attachment Remove obstruction Notches PRECAUTIONARY MEASURES Important If the suction opening in the unit the hose or the extension tube become blocked switch off the vacuum cleaner and remove the blocking substance before you start the unit again Do not operate the vacuum cleaner to close too heaters or radiators Before inserting the power plug into the wall outlet make sure that your hands are dry WS ee E e Ailes T a Pan HS e Eai i r fal a Do not vacuum any liquids Keep hair loose clothing fingers feet and all parts of body away from Openings rotating agitator and other moving parts 5 When pulling out the power plug from the wall outlet pull the plug not the power cord Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not run appliance over power cord Do not use without dust cup filter or filters in place Before you start vacuuming make sure to remove large or sharp objects that might d
16. rom wall outlet 2 With a flat head screw driver snap off the lens cover by pressing down on the two notches on the lens cover Fig 23 3 Lift off the head light lens PROBLEM SOLVING This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory If a minor problem occurs it usually can be solved quite easily when the cause is found Therefore this checklist is provided for your convenience PROBLEM POSSIBLE CAUSE POSSIBLE Cleaner Won t Run Cleaner Won t Pick Up Cleaner Picks Up Moveable Rugs Or Pushes Too Hard Agitator Does Not Turn Air Flow Restricted With Attachment Use Sound Changes Ne ee Not properly plugged into wall outlet No electricity in wall outlet On Off switch not turned on Motor thermostat tripped Blown fuse tripped breaker Full or clogged dust cup Wrong pile height setting Clogged nozzle Clogged dust inlet port Clogged hose Broken belt Hose not inserted fully Dirty filters Wrong pile height setting Broken belt Belt installed incorrectly Attachment use restricts air flow New carpet debris clogging air path Fig 23 Remove the light bulb by pulling it out carefully Replace the new bulb by pushing it in Replace the head light lens by pushing it in so that it snaps back in place Plug in firmly Check fuse or breaker Push on off switch to on Reset motor the
17. sed by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice OWNERSHIP REGISTRATION CARD FOR CANADIAN C
18. the On position to turn the vacuum on 4 Torelease the handle step on the power head and pull the handle back 5 When using the attachments the vacuum must be in the upright position Fig 3 OPERATING INSTRUCTIONS Carpet Height Selector This upright vacuum can be used on multiple types of carpeting bare floors or upholstery with attachments To select a pile height setting 1 Turn vacuum cleaner Off 2 Selecta pile height setting by sliding the carpet height selector to the desired setting Fig 4 Suggested Pile Height Setting You may need to raise the height of the vacuum to make some jobs easier such as scatter rugs and longer pile carpets Suggested settings are Low Oo E H High Carpet Carpet Hard En Floor Tools HIGH shag carpet long pile plush scatter rugs tools MED medium to long pile LOW short to medium pile bare floors FLOOR very low pile bare floors Place unit in HIGH setting when using attachments to prevent possible floor damage Always set the Carpet to Floor selector to Floor setting when using the accessories Fig 5 Attention Special care is required when vacuuming certain types of carpet or floor covering Always check the carpet or floor covering manufacturer s recommended cleaning instructions before vacuuming Removing amp Emptying Dust Cup Warning To reduce the risk of electric shock the power cord must be disconnected be
Download Pdf Manuals
Related Search