Epson Personal Document Station User Setup Information
Contents
1. Windows manual A mouse or other compatible pointing device O A Video Graphics Array VGA or other Windows compatible display adapter card or built in interface O A monitor compatible with the card or interface you are using 2 Getting Started Installing the Parallel Interface Card Follow the steps in this section if you need to install the bidirectional parallel interface card in your computer You may also need to configure the card before you install it Some computers come with a built in bidirectional parallel interface You do not need to install the parallel interface board if your computer has a built in interface that you are not currently using If you will connect the scanner to an existing interface skip to Setting Up the Scanner on page 6 Note Standard unidirectional and bidirectional parallel interfaces look the same but operate differently Your scanner does not work with a standard parallel interface so check your computer manual to make sure you have an unused bidirectional parallel interface before you connect the scanner to it Configuring the Card The parallel interface board contains jumpers that select the port address LPT or LPT 2 and interrupt IRQ 5 or IRQ 7 the card uses You may need to change the jumper settings if there is a conflict with your computer s parallel port settings See your computer manual for information about the port address and interrupt used by its parallel2. EPSON Personal Document Station Getting Started D Printed on recycled paper with at least 10 post consumer content A Note Concerning Responsible Use of Copyrighted Materials Like photocopiers scanners can be misused by improper copying of copyrighted material Although Section 107 of the U S Copyright Act of 1976 Title 17 United States Code the fair use doctrine permits limited copying in certain circumstances those circumstances may not be as broad as some people assume Unless you have the advice of a knowledgeable attorney be responsible and respectful by not scanning published material without the permission of the copyright holder Copyright Notice All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations t
3. al information library fax service O Product literature on current and new products You can purchase ink cartridges paper parts and accessories for EPSON products from EPSON Accessories at 800 873 7766 U S sales only In Canada call 800 BUY EPSON for sales locations When you call for technical assistance be ready to identify your scanner and system configuration and describe any error conditions to the support staff If you purchased your scanner outside the United States or Canada contact your EPSON dealer or the marketing location nearest you for customer support and service CompuServe on line support If you have a modem the fastest way to access helpful tips specifications drivers application notes tables for DIP switch or jumper settings and bulletins for EPSON products is through the Epson America Forum on CompuServe If you are already a CompuServe member simply type GO EPSON at the menu prompt to reach the Epson America Forum 16 Getting Started
4. fore you plug in any cables Connect the 25 pin end of the parallel cable to the parallel port on your computer then tighten the screws on the connector Connect the other end of the cable to the parallel interface on the side of the scanner and fasten it with the wire clamps 6 Getting Started 6 Connect the scanner s power cable to the power inlet on the rear of the scanner and plug the other end into a grounded electrical outlet D a 7 Turn the scanner around and lift up the cover Getting Started 7 Turn on the scanner by pressing thelend of the power switch The green Power light on the top right side of the scanner comes on The Ready light also flashes while the scanner warms up Turn on your monitor and all your other peripheral devices Then turn on the computer Always turn on the scanner before the computer The scanner s Ready light goes out when you turn on the computer and then comes on again once the computer boots Installing the Xerox Desktop Document Management Suite Follow these steps to install the Desktop Document Management Suite or DDMS software on your computer s hard disk drive L 2 Start Windows if necessary Insert the Xerox DDMS Disk 1 into a diskette drive From the Program Manager open the File menu and choose Run You see the Run dialog box Type A SETUP or B SETUP if you inserted the diskette in drive B in the Command Line Box and ch
5. ing Interface dialog box appears as the active window Note The Xerox Scanning Interface dialog box appears automatically only after the Paper Sensor detects paper loaded in the scanner 8 For this first scan do not adjust any of the other image settings available in the dialog box Choose Scan 9 The scanner reads the first page and after a moment a scanned image of the page appears in the Preview area the large rectangle in the dialog box It also displays a reduced view of the page in the Thumbnail area on the left side of the dialog box Getting Started 13 10 Click Done You see the Xerox Image Manager window From the Image Manager you can save your scanned document to a file or print fax or e mail the document without saving it See the manuals quick reference cards and on line help utilities that came with the Desktop Document Management Suite to process your scanned image using the various program components Installing the EPSON TWAIN Driver The EPSON Personal Document Station TWAIN Driver diskette that came with your scanner contains the TWAIN driver its installation program and a README file You do not need to install this driver to use the Personal Document Station you need it only if you use an image editing program such as Photoshop or Picture Publisher that requires a TWAIN driver 14 Getting Started Follow these steps to install the driver and print the README file 1 Inse
6. irectory in which to install the program files or delete it and enter a new directory Then choose OK 11 The program begins copying files to your hard disk drive and prompts you to insert the rest of the diskettes Follow the instructions on the screen 12 After all the files are copied you see a dialog box where you must enter your name company optional and the serial number of the DDMS program The serial number is usually printed inside the manual or on the registration card Enter this information and choose Continue 13 The program creates a Windows program group and icons Then you see the Exit Setup screen choose OK 14 The program starts the Windows Write program and displays the Release Notes file Read this file for the latest information about your software and print it if you like 15 Open the File menu and select Exit to exit Write 16 Remove the last installation diskette from the diskette drive 17 Exit Windows The installation program placed the Xerox DDMS Control Panel and Paper Sensor icons in your Windows Startup group and created a Xerox Applications group See the instructions in the next section to scan a test document Then read the Xerox Desktop Document Management Suite manuals quick reference guides and on line help utilities for instructions on using the programs to process your scanned documents 10 Getting Started Scanning Documents Now you are ready to start scanning using the b
7. isher See page 14 for more information To fax or e mail your scanned images you must also have one of the following fax and e mail application programs Fax applications E mail applications Delrina WinFax Pro or WinFax LITE Microsoft Mail SofNet FaxWorks Lotus cc Mail Bit Software BitFax Professional Lotus Notes Mail Note Other programs may be supported see the release notes and installation program screens as you install the Desktop Document Management Suite for the latest information Getting Started 1 This booklet tells you how to set up your scanner install the software and scan a document For additional instructions see the manual for the ES300GS scanner and the manuals quick reference cards and on line help utilities for the Desktop Document Management Suite System and Memory Requirements For the scanner hardware and software to work properly your system must include the following minimum configuration O A 386 based or higher IBM compatible computer or an IBM PS 2 MS DOS version 5 0 or higher Microsoft Windows 3 1 or higher or Windows NT running in enhanced mode only 3 5 inch high density diskette drive At least 100MB of hard disk space for scanner applications and images O 8MB of system RAM plus a permanent Windows swap file providing 8MB to 16MB of virtual memory a swap file of contiguous space on your hard disk drive which Windows can use see your Microsoft
8. o this product Seiko Epson Corporation and its affiliates shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation EPSON is a registered trademark of Seiko Epson Corporation General notice Other product names used herein are for identification purposes only and may be trademarks of their respective companies EPSON disclaims any and all rights in those marks Copyright 1995 by Epson America Inc Torrance California USA 4 95 Introduction This package contains everything you need for professional quality document scanning and processing O EPSON Personal Document Station ES 300GS scanner which scans in 8 bit monochrome grayscale at up to 400 dpi and includes a built in document feeder and an attachable business card guide O Bidirectional parallel interface card which provides an additional parallel interface for your computer O Bidirectional parallel interface cable O Xerox Desktop Document Management Suite for Microsoft Windows an integrated software package including image editing faxing e mail optical character recognition OCR printing and file creation capabilities for processing your scanned images O Additional TWAIN driver for using your scanner with other image editing programs such as Adobe Photoshop and Micrografx Picture Publ
9. oose OK After a few moments you see the installation program dialog box choose Continue 8 Getting Started 6 The next screen asks you for the directory in which you want to install the program files Accept the default directory or delete it and enter a new directory Installation Options Installation Directory C DDMS HC J Eile Management 640 K install Personal Cabinet Space Required 640 K Space Available 52612 K Checkboxes on this screen let you exclude certain components of the program from the installation process In most cases install all the program components the default setting and choose Continue For more information on the program components see the Xerox DDMS manual 7 At the next screen select the e mail application program you ll be using or select none and choose Continue 8 Then select your fax application program or select none and choose Continue 9 If you selected not to install the OCR component in step 6 skip to step 10 now Otherwise you see the OCR Language Packs screen You can install up to five language packs for your OCR program English is selected by default select the checkbox for any other languages you want to install and choose Continue Getting Started 9 10 If you selected not to install the File Management or Personal Cabinet components in step 6 skip to step 11 Otherwise you see the Visual Recall Setup screen Accept the default d
10. port The bidirectional parallel interface card default settings are O Port address LPT2 O Interrupt IRQS Your computer s parallel port probably uses LPT1 and a different IRQ setting However if it uses LPT2 or IRQ5 follow the steps below to change the interface card s jumper settings Getting Started 3 l Carefully remove the interface board from its packaging holding it only by its top edges Then place it on a flat clean surface Caution Avoid touching the components or the gold contacts on the interface board they can be damaged by static electricity 2 Locate jumpers J1 and J2 on the interface board as shown below 0 0 0 i 0 0 0 0 0 0 iF 0 000 are ead 0 0 0000 J2 O 0 0 KE le re M n LS 3 The settings are printed on the circuit board next to the jumpers To change a setting lift off the jumper cap and reinstall it over the appropriate pair of pins Caution Be careful not to bend the jumper pins 4 Getting Started Installing the Card Follow these steps to install the card in your computer 1 Turn off the computer and any peripheral devices 2 Disconnect the computer s power cable from the electrical outlet and from the back panel Also disconnect any other cables including the keyboard cable 3 Remove the cove
11. r from your computer If you need detailed instructions see your computer manual 4 Before you touch any of the computer s internal components touch an unpainted metal surface inside the computer case to discharge any static electricity 5 Choose an option slot for the interface card You can install the card in any available slot 6 Remove the retaining screw from the option slot cover and remove the slot cover Keep the screw to secure the interface card to the computer Store the slot cover in a safe place in case you remove the interface card later 7 Insert the interface card into the slot guiding it straight down Push the card down firmly but carefully you should feel it fit into place 8 Secure the card to the computer with the retaining screw 9 Replace the computer s cover reconnect all the cables and plug the power cord into an electrical outlet Getting Started 5 Settng Up the Scanner Follow these steps to set up the scanner k Take the scanner out of its box and place it on a flat stable surface with the rear panel facing you Remove the tape securing the scanner cover and pull out any packing material from underneath the cover Turn off your computer scanner and any other peripheral devices The scanner is turned off when the O end of the power switch on the rear panel is pressed down Caution Be sure that your computer scanner and any other peripheral devices are turned off be
12. rt the EPSON PDS TWAIN Driver diskette in a diskette drive 2 From the Windows Program Manager select Run from the File menu You see the Run dialog box 3 In the Command Line box type A SETUP or B SETUP and choose OK 4 At the installation program title screen choose OK 5 At the next screen confirm or correct the Windows directory and choose OK The program installs the driver files 6 In the Scanner Setup dialog box open the Interface pull down menu and select BID Parallel and choose OK 7 The program creates the EPSON Scanner group containing a READ ME icon Double click the READ ME icon the Windows Write program starts and displays the README file contents 8 Select Print from the File menu to print the file Follow the instructions in the README file to use the TWAIN driver with your image editing program Where to Get Help If you purchased your scanner in the United States or Canada EPSON provides customer support and service through a network of Authorized EPSON Customer Care Centers EPSON also provides support services through the EPSON Connection In the United States and Canada dial 800 922 4911 Getting Started 15 Call the EPSON Connection for the following O Technical assistance with the installation configuration and operation of EPSON products O Assistance in locating your nearest Authorized EPSON Reseller or Customer Care Center O Customer relations O EPSON technic
13. uilt in document feeder For instructions on using the attachable business card guide see your ES3O0OGS User s Guide When scanning documents respect the rights of the copyright holders Don t scan published materials without first checking the copyright status L First select a multiple page document to scan up to 10 pages on standard bond paper Make sure all the pages are the same size and paper weight Also remove any paper clips staples tape glue or other foreign objects from the document Caution Y Scanning documents that contain foreign objects such as paper clips or staples can damage the scanner mechanism and the glass scanning window Beneath the scanner cover flip down both paper guides to the operating position as shown below Getting Started 11 3 Fan the edges of your document then level the stack by tapping it on a flat surface 4 Hold the document with the side to be scanned facing down and guide it into the scanner s document feeder as shown 5 Adjust the paper guides to fit the width of the paper The scanner feeds the first page into scanning position 6 Start Windows You see the Xerox DDMS Control Panel window shown below and the Paper Sensor icon on your Windows desktop Note If your Program Manager window is maximized you do not see the Control Panel or Paper Sensor icon Reduce the window Size 12 Getting Started 7 After a few moments the Xerox Scann
Download Pdf Manuals
Related Search