Epson ESC/POS TM-U220 User's Manual
Contents
1. No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this book Seiko Epson Corporation assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding the U S failure to strictly comply with Seiko Epson Corporation s operating and maintenance instructions Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation EPSON and ESC POS are registered trademarks of Seiko Epson Corporation NOTICE The contents of this manual are subject to change without notice Copyright 2003 by Seiko Epson Corpor2. Undefinea dJ internal use only E a flash memory rewriting 7 Undefined Serial interface selection E switch switch vi STD Serial DIP Switch 1 Parallel DIP Switch 1 SW Funeion Jon CS H Wesen s ss SW Function om om Auto line feed Enabled Disabled Receive buffer capacity 40 bytes BUSY condition Receive Receive buffer full bufferfullor Offline BUSY condition Receive Receive buffer full bufferfullor Offline Parallel DIP Switch 2 sw Function fon o zl Print column selection 42 35 40 33 For internal use only Enabled Disabled Sur Ze Serial DIP Switch 2 SW function Jon CA s or 2 For internal use only Enabled Disabled autocutter 3 Undefined NU mes o interface selection c M switch oz dll eu memory a 7 undefined ja 5 Undefined For internal use only flash memory rewriting vii TM U220 Specifications Font standard Font A 7 x 9 Font B 9 x 9 Column capacity 7x 9 9 x 9 columns 76 mm 40 33 69 5 mm 36 30 57 5 mm 30 25 Character size W x H 1 2x 3 1 mm 1 6 x 3 1 mm not including horizontal standard spacing Character set 95 Alphanumeric 37 International 128 x 12 Graphic Characters per inch Font A 7 x 9 16 cpi Font B 9 x 9 13 3 cpi standard 3 half dot spacing Paper Dimensions mm 57 5 0 5 69 5 0 5 76 0 5 Normal paper mm Thickness 0 06 0 085 1 sheet Pressure sensetive T
3. AN CAUTION The print head becomes very hot during printing Allow it to cool before you replace the ribbon cassette N CAUTION Never turn the ribbon cassette s feed knob in The opposite direction of the arrow marked on the cassette otherwise the ribbon cassette may be damaged Note Use the EPSON ERC 38 ribbon cassette for your printer 1 Open the ribbon cassette cover by using the tabs on the sides of the cover as shown in illustration D 2 Turn the knob two or three times in the direction of the arrow as shown in illustration E 3 Insert the ribbon in the position shown in illustration F and push the ribbon cassette down until it clicks Note Make sure the ribbon is installed between the print head and the platen without wrinkles or creases 6 TM U220 User s Manual 4 Again turn the ribbon cassette s knob 2 or 3 times in the direction of the arrow and close the ribbon cassette cover A A CAUTION Be careful not to touch the print head with your fingers when turning the ribbon cassette knob because the print head is hot and you might be burned When you replace the ribbon casette lift the left side of the ribbon cassette first then lift the whole ribbon cassette Inserting Roll Paper N CAUTION Be sure to use roll paper that meets the specifications Be sure not to touch the manual cutter Otherwise your fingers might be injured 1 2 10 Using scissors cut the leading edge of the roll p
4. not install the printer in a dusty place Protect the printer from impact Cords or other foreign objects must not be caught on the printer Do not apply excessive force to the printer case Do not place food or beverages such as coffee on the case of the printer LLLDLL Notes on Installation L When using the printer be sure that the printer is installed horizontally d If you are using a Type B or D printer you can hang it on a wall using the optional hanging bracket set WH 10 Note To hang the printer on a wall see the WH 10 Installation Manual for detailed instructions Purpose of This Manual This manual provides information to operators of the TM U220 to describe basic operations to enable safe and correct use of the printer Features of Printer Types See illustration A vee ie web Paper width mm 76 69 5 57 5 76 69 5 57 5 Serial or parallel Serial or parallel Serial or parallel Characters supported Alphanumeric Alphanumeric Alphanumeric 4 TM U220 User s Manual Illustrations Because this manual covers three types of the TM U220 some of the illustrations may be slightly different from your printer however the instructions cover all types except as noted Unpacking The following items are included for the standard specification printer If any item is damaged contact your dealer LJ Printer d Roll paper L Exclusive ribbon cassette ERC 38 P ERC 38 B R JJ AC adapter May not be inclu
5. TM U220 Printers User s Manual Bedienungsanleitung Gebruikershandleiding Manuel d utilisation Manual do utilizador Manual del usuario Manuale dell utente 404312200 ERROR PAPER OUT H POWER FEED 1i 10 DIP Switch Tables Look at the numbers and letters in the area indicated in the illustration If the last letters are US use the US tables below If the last letters are STD use the STD tables CAUTION Be sure to replace the DIP switch cover before using the printer US Serial DIP Switch 1 Parallel DIP Switch 1 sw Function fon o 1 Auto line feed Enabled Disabled Receive buffer 40 bytes rodes _ KB EODEM sw Function o ot 4 Wordiengh bs ao 6 Poriyselection feen Odd BUSY condition Receive Receive Parallel DIP Switch 2 Pure or fine SW Function mm Jon 2 For internal use only Enabled Disabled autocutter BUSY condition Receive Receive buffer full buffer full or Offline Serial DIP Switch 2 mpn NU Pintcoumn 42 35 urs internal use only Enabled Disabled RIDE 2 5 Undefined For internal use only Lr EM flash memory ENS Undefined 5
6. aper as shown in illustration G Turn on the printer and open the roll paper cover by using the tab as shown in illustration H Type A only Open the unit by using the unit open lever as shown in illustration I Insert the roll paper as shown in illustration J Note Note the direction the paper comes off the roll as shown in the illustration G When using 2 ply roll paper be sure that the top and bottom sheets are aligned at the paper exit See illustration G Q If you are not using a take up spool pull out a small amount of roll paper and close the roll paper cover then tear off the paper with the manual cutter You can skip steps 6 through 11 Type A only When using 2 ply roll paper pull out the roll paper to the bottom front of the printer as a guide as shown in illustration K Close the unit as shown in illustration L Insert the end of the bottom paper journal paper into the paper take up spool as shown in illustration M Insert the paper take up spool in the printer Be sure that the paper is aligned with the spool s flange as shown in illustration N Feed the paper with the FEED button so that the paper is taken up by the spool TM U220 User s Manual 7 11 Close the roll paper cover and tear off the roll paper with the manual cutter as shown in illustration O Note Do not open the roll paper cover during printing or paper feeding When using the printer be sure to cut the roll paper with th
7. ation Nagano Japan EMC and Safety Standards Applied Product Name TM U220A TM U220B TM U220D Model Name M188A M188B M188D The following standards are applied only to the printers that are so labeled EMC is tested using the EPSON power supplies Europe CE marking Safety TUV EN 60950 North America EMI FCC ICES 003 Class A Safety UL 60950 CSA C22 2 No 60950 Japan EMI VCCI Class A Oceania EMC AS NZS 3548 Class B WARNING The connection of a non shielded printer interface cable to this printer will invalidate the EMC standards of this device You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your authority to operate the equipment This class III equipment should be used with an approved power supply with SELV outputs CE Marking The printer conforms to the following Directives and Norms Directive 89 336 EEC EN 55022 Class B EN 55024 IEC 61000 4 2 IEC 61000 4 3 IEC 61000 4 4 IEC 61000 4 5 IEC 61000 4 6 IEC 61000 4 11 FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not install
8. ded with the printer Control Panel LEDs and Buttons See illustration B LEDs POWER Lights when the power is on and is off when the power is off ERROR Lights when the printer is offline when the roll paper is at the end or the roll paper cover is open Off when the printer operates correctly Flashes when an error occurs See the Troubleshooting section PAPER OUT Lights when roll paper is out or nearly out Buttons FEED FEED feeds the roll paper Note Paper cannot be fed by using this button when a paper out is detected TM U220 User s Manual 5 _ English Power Supply Switch and Power Supply Switch Cover The power supply switch is on the front of the printer Press the power supply switch to turn on the printer Power Supply Switch Cover You can use the enclosed power supply switch cover to make sure that the power supply switch is not accidentally pressed Just press the cover into place to install it If you need to turn the power supply switch on or off with the cover attached you can insert a thin tool into one of the holes in the cover to operate the switch See illustration C N WARNING If an accident occurs when the power supply switch cover is attached immediately unplug the power supply cable to avoid fire If you are going to store the printer or leave it unused for a long time turn it off using the power supply switch on the printer Inserting and Replacing the Ribbon Cassette A
9. e manual cutter after paper feeding is complete Replacing Roll Paper 1 Open the roll paper cover by using the tab as shown in illustration H 2 Types B and D Remove the used roll paper core 3 Type A only Remove the take up spool and open the unit by using the unit open lever as shown in illustration I then remove the used roll paper core 4 Insert new roll paper See the section Inserting Roll Paper Troubleshooting No lights on the control panel d Check the power supply cable connections and the power outlet ERROR LED is flashing or lit d The print head temperature may be too high or low Wait until the print head cools or warms and the printer resumes printing automatically Make sure that the roll paper cover is properly closed Types A and B The autocutter blade is not in the normal position and the autocutter is locked up If it is a simple lock up the error is corrected automatically If not see the instructions below to return the blade to the normal position manually A paper jam has occurred To remove the jammed paper see the instructions below Be sure to check if the specified power source is used PA 6xxx and PB 6xxx cannot be used with this printer Turn off the power wait several seconds and then turn it on again If the error remains contact your supervisor or a qualified service person 8 TM U220 User s Manual Returning the autocutter blade to the normal position 1 Open th
10. e roll paper cover by using the tab as shown in illustration H 2 Use a ballpoint pen or tweezers to turn the knob of the autocutter in the direction indicated by the arrow until you see a round shaft in the hole as shown in illustration P Removing jammed paper A AN CAUTION The print head becomes very hot during printing Allow it to cool before you reach into the printer 1 Open the roll paper cover by using the tab as shown in illustration H 2 Ifyou have a Type A printer remove the take up spool and open the unit by using the unit open lever as shown in illustration I 3 Remove the jammed paper 4 Re insert the roll paper and close the roll paper cover EPSON Ecology Label This product is in compliance with the EPSON ecology label requirements Please see the following link for detailed information on label criteria http www epson co jp e TM U220 User s Manual 9 10 TM U220 User s Manual
11. ed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FOR CANADIAN USERS This Class A digital apparatus complies with Canadian ICES 003 Important Safety Information This section presents important information intended to ensure safe and effective use of this product Read this section carefully and store it in an accessible location Key to Symbols The symbols in this manual are identified by their level of importance as defined below Read the following carefully before handling the product N WARNING Warnings must be followed carefully to avoid serious bodily injury N CAUTION Cautions must be observed to avoid minor injury to yourself or damage to your equipment 2 TM U220 User s Manual Safety Precautions N WARNING Shut down your equipment immediately if it produces smoke a strange odor or unusual noise Continued use may lead fo fire Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for aavice Never attempt to repair this product yourself Improper repair work can be dangerous Never disassemble or modify this product Tampering with this product may result in injury or fire Be sure to use the specified power source Co
12. hickness 0 05 0 08 1 sheet total thickness must be paper 0 14 mm or less Number of copies Original 1 sheet one copy sheet Ribbon cassettes ERC 38 P Purple life 4 000 000 characters ERC 38 B Black life 3 000 000 characters ERC 38 B R Black Red life Black 1 500 000 Red 750 000 characters Life based on continuous printing at 25 C 77 F 10 90 must be no condensation Storage 10 90 must be no condensation without paper and ribbon cassette Overall dimensions mm Type A 160 x 286 x 157 5 W x D x H Type B 160 x 248 x 138 5 W x Dx H Type D 160 x 248 x 138 5 W x Dx H Mass approx Type A 2 7 kg Type B 2 5 kg Type D 2 3 kg dpi dots per 25 4 mm dots per inch Ips lines per second Ipi lines per 25 4 mm lines per inch viti TM U220 Printers User s Manual DIP Switches and Specifications The technical specifications and the information about the DIP switches are at the beginning of this manual Illustrations All of the illustrations are at the beginning of this manual They are identified by letters A B C In the text the illustrations are referred to by these letters See illustration A for example Some of these illustrations have numbered arrows or lines pointing to parts of the illustration See the list below for the meaning of the numbers Illustration A 1 Roll paper cover 2 Ribbon cassette cover 3 Control panel 4 Power supply switch All rights reserved
13. nnection to an improper power source may cause fire Do not allow foreign matter to fall into the equipment Penetration by foreign objects may lead fo fire If water or other liquid spills into this equipment do not continue to use it Continued use may lead to fire Unplug the power cord immediately and contact your dealer or a Seiko Epson service center for advice N CAUTION Do not connect cables in ways other than those mentioned in this manual Different connections may cause equipment damage and burning Be sure to set this equipment on a firm stable horizontal surface Product may break or cause injury if if falls Do not use in locations subject to high humidity or dust levels Excessive humidity and dust may cause equipment damage or fire Do not place heavy objects on top of this product Never stand or lean on this product Equipment may fall or collapse causing breakage and possible injury To ensure safety unplug this product before leaving it unused for an extended period Before moving the product unplug it and unplug all cables connected to it Safety Label N WARNING Do not connect a telephone line fo The drawer kick out connector otherwise the printer and the Telephone line may be damaged A A CAUTION During printing or after printing the print head can be very hot TM U220 User s Manual 3 Notes on Usage d Do not open the cover during printing or when the autocutter is being operated Do
Download Pdf Manuals
Related Search