Epson F2000 Start Here Guide
Contents
1. Product Support Online User s Guide Instructions for using your printer and maintenance tools On screen help with your software Select Help or F1 when youre using your Garment Creator software Epson technical support Internet support Visit your product s support website at epson com support f2000 U S or epson ca support f2000 Canada to download the Garment Creator software and utilities access the online Users Guide get FAQs and troubleshooting advice or e mail Epson with your questions Epson Preferred Protection Plan Call 888 377 6611 Make sure you have your Epson Preferred Unit ID number If you have any difficulty with this service call 562 276 1305 You can purchase a one year extended service plan through your Epson authorized reseller or from Epson Need Ink You can purchase ink from an Epson DTG authorized reseller To find the nearest reseller call 800 GO EPSON 800 463 7766 EPSON and SureColor are registered trademarks and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation Epson Preferred is a service mark of Epson America Inc General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners Epson disclaims any and all rights in those marks This information is subject to change without notice 2013 Epson America Inc 12 13 Printed in USA CPD 402542. kilograms and requires three people to lift and move it Make sure to grip the printer where indicated by the gray stickers as shown in the illustration When moving the printer do not tilt it more than 10 degrees 3 Remove the carriage lock and store it in a safe place Note Do not throw the carriage lock away you will need it if you transport the printer amp Open the printer cover and press down on the parts as shown to make sure they are secure Then close the cover AA WIS JQ BRAS Assemble the Printer 1 Attach the platen as shown 2 Remove the plugs from the waste ink outlets on the back of the printer and store them in a i Note Do not throw the plugs away you will need them if you transport the printer safe place 3 Connect the waste ink tube Make sure that the longer end of the tube is connected to the waste ink outlet on the left side and the shorter end is connected to the waste ink outlet on the right side l Attach the two tube clamps to the left and right sides on the back of the printer and route the waste ink tube through the clamps as shown 5 Remove the outer and inner caps from the waste ink bottle and store them in a safe place Note Do not throw the caps away you will need them when disposing of the waste ink gi a 6 Place the caution label for your language over the English labe
3. Epson SureColor F2000 Series Choose a Location for the Printer Choose a location for the printer that is near a wall outlet where the plug can be easily unplugged Avoid places subject to rapid changes in temperature and humidity Also keep the printer away from direct sunlight strong light or heat sources Make sure to place the printer on a flat stable surface with enough space on all sides see illustrations below The area supporting the printer should be wider than the space between the rubber feet on the bottom of the printer at least 2 feet 60 cm off the ground and capable of supporting at least 220 pounds 100 kg 1 26 in 23 in 3 2 cm aa lt 4 58 5 CM 78 74 in 200 cm 47 24 in a 120 cm Sw 19 68 in 2 55 in 50 cm 6 5 cm Unpack 1 Make sure you have these items Medium platen Waste ink bottle Waste ink tube Power cord D o te Ink cartridges Maintenance kit Tweezers Waste ink Caution Limited Tube cable clamps bottle holder label warranty Note e The White Edition includes two additional cleaning cartridges e See the online User s Guide for information on using the maintenance kit and tweezers and attaching the two cable clamps 2 Remove all the packaging materials and tape Check carefully for all the tape inside and outside the printer and platen WARNING The printer weighs about 180 pounds 82
4. l if necessary Then insert the y guag g y waste ink bottle into the waste ink bottle holder The bottle and holder should be placed in an area lower than the printer so that the waste ink can flow straight down s gt 4 T Insert the waste ink tube into the waste ink bottle The tube should curve toward the bottle and straight down as shown Make sure that the tube sits above the yellow line indicated on the outside of the bottle If the tube is too long cut the end to the appropriate length gt S lt 8 Connect the power cord Do not connect the printer to your computer yet Install Ink Cartridges Caution You cannot change the ink configuration for example White Edition to Color Edition or Color Edition to White Edition after the ink cartridges have been installed 1 Remove the ink cartridges from their packages and then gently shake each cartridge for about 15 seconds on each side as shown 2 Open the ink covers and install each cartridge into the correct slot for its color Caution Do not touch the green chip on top of the cartridge White Edition Left ink bay Right ink bay ai Color Edition Left ink bay Right ink bay BK 3 Close the ink covers Press the button Follow the prompts to select Language set Date amp Time and select unit of measurement L_J Press the t button O 0 A Press OK at each of the confirmation pro
5. mpts The printer starts charging the ink This takes about 40 minutes The LCD displays Standby when the charging is complete Caution Do not turn off or unplug the printer while the cb light is flashing Also do not open the ink covers during the charging process Note The first time you install ink cartridges the printer uses some ink to charge the printing system so print yields may be lower with the first cartridges Subsequent ink cartridges will last for their full rated life Install Software amp Drivers 1 Go to epson com support f2000 U S or epson ca support f2000 Canada to download the Garment Creator software and Drivers amp Utilities Combo Package 2 After you install the software open the LFP Remote Panel and check for a firmware update Perform Nozzle Check 1 Remove the platen s frame 3 Press the pY button on the control panel The Maintenance menu is displayed 4 Press the A W buttons to highlight Nozzle Check and then press the p gt button 5 Press the OK button twice 6 The nozzle check pattern is printed directly onto the platen ji T Check the pattern If there are no gaps the nozzles are clean If there are gaps in the pattern refer to the online Users Guide for instructions on cleaning the print head 8 Clean the platen using a cloth dampened with window cleaner or water 9 Replace the platen s frame a NEZZ A P aoe Qe w
Download Pdf Manuals
Related Search