Epson Stylus Scan 2000 All-in-One Printer Product Information Guide
Contents
1. Ink jet cards A6 105 x 148 mm Ink jet cards distributed by EPSON 8 x 10 inches Photo paper Letter 8 5 x 11 inches A4 210 x 297 mm 4 x 6 inches 102 x 152 mm Panoramic 210 x 594 mm Photo paper distributed by EPSON Photo stickers A6 105 x 148 mm with 16 frames Photo stickers distributed by EPSON Iron On Cool Peel transfer paper Letter 8 5 x 11 inches Transfer paper distributed by EPSON Matte paper Heavyweight Letter 8 5 x 11 inches A4 210 x 297 mm Matte paper distributed by EPSON Note Since the quality of any pa any non EPSON brand or type of paper Always test samples of paper stock before purchasing large quantit ticular brand or type of paper may be changed by the manufacturer at any time EPSON cannot attest to the quality of ies or printing large jobs Poor quality paper may reduce print quality and cause paper jams and other problems If you encounter problems switch to a higher grade of paper Print only under these conditions Temperature 59 to 77 F 15 to 25 C Humidity Store glossy film and self adhesive sheets under these conditions 40 to 60 RH Temperature 59 to 86 F 15 to 30 C Humidity 20 to 60 RH 2 EPSON Stylus Scan 2000 9 99 EPSON Stylus Scan 2000 Printable Area A BL BR BL Single sheets and cards BR Envelopes A The minimum top mar2. WARNING If ink gets on your hands wash them thoroughly with soap and water If ink gets in your eyes flush them immediately with water 10 Press the st cleaning button to begin charging the ink delivery system and close the front cover Charging takes about 2 minutes The power light flashes and the printer makes various sounds until it s finished Don t turn off the printer or interrupt the charging process or it will start over using more ink than necessary Charging is finished when the power light stops flashing and stays on Caution Never turn off the printer while the power light is flashing unless the printer hasn t moved or made any noise for more than 5 minutes 6 EPSON Stylus Scan 2000 9 99 Loading Paper 1 Open the output tray and its extensions Slide the edge guide out until it is a little wider than your paper Load a stack of paper with the printable side up and place it against the right side of the feeder Then slide the edge guide up against the paper s left edge Don t load paper higher than the arrow on the guide If the paper has a corner cut make sure you load it as shown Slide the edge guide against the paper Testing the Printer You can run a printer operation check to determine whether the problem comes from the printer or some other source m If the results are satisfactory the problem lies in your software settings the interface cable
3. 4 to 140 F 20 to 60 C 120 hours at 140 F 60 C Humidity Operation 20 to 80 RH Storage 5 to 85 RH without condensation Stored in shipping container Safety Approvals Safety standards EMC UL 1950 with D3 CSA 22 2 No 950 FCC part 15 subpart B class B 4 EPSON Stylus Scan 2000 9 99 Connector 57 30360 Amphenol connector or equivalent Reverse channel Specification Description Transmission mode IEEE 1284 Nibble mode IEEE 1284 ECP mode Adaptable connector 57 30360 Amphenol connector or equivalent Synchronization Refer to the IEEE 1284 specification Handshaking Refer to the IEEE 1284 specification Signal level IEEE 1284 Level 1 device Data transmission timing Refer to the IEEE 1284 specification EPSON Stylus Scan 2000 Control Panel load eject button power light paper 5 out light Oh co _ Power button black ink ts out light Ob eH cleaning color ink button l Ow out light m sean copy 141 O O des error light 93 O e button 70 O reduce copy button enlarge fe O O copy mode button button Follow these guidelines when the control panel lights come on or flash j When the i paper out light flashes paper is jammed in the printer Turn off the printer remove all the paper including any pieces torn off inside then reload the stack Turn on the
4. PL SCAN2000 EPSON Stylus Scan 2000 Parts Price List Continue with step 4 CPD 8877 EPSON Stylus Scan 2000 User s Guide CPD 8878 EPSON Stylus Scan 2000 Start Here sheet 12 EPSON Stylus Scan 2000 9 99
5. four or five times turn the printer off wait until the next day and run the cleaning cycle again LI If quality still doesn t improve one or both of your ink cartridges may be old or damaged and you may need to replace them See page 8 for instructions EPSON Stylus Scan 2000 Aligning the Print Head If your printouts contain misaligned vertical lines you may need to align the print head using the Print Head Alignment utility in your printer software Your EPSON Stylus Scan must be connected to a local port not on a network to use this utility 1 Make sure the printer is turned on and paper is loaded Caution Load paper that s at least 8 27 inches 210 mm wide This prevents ink from spraying inside the printer and smudging your printouts For the best results load EPSON ink jet paper in the printer whenever you check the print head alignment 2 Do one of the following LI Windows Click Start point to Settings then select Printers Right click the EPSON Stylus Scan 2000 icon and select Properties Click the Utility tab 1 Macintosh Open the File menu and choose Page Setup or Print Then click the Utility icon Click the Print Head Alignment icon on the Utility menu 4 Follow the instructions on the screen to print a test page and select the correct alignment Cleaning the EPSON Stylus Scan To keep your printer working at its best you should clean it several times a year following
6. or your computer L Ifthe check page does not print correctly you have a problem with your printer See the Users Guide for possible solutions 1 Make sure both the printer and computer are turned off 2 3 Caution Load paper that s at least 8 27 inches 210 mm wide This prevents ink from spraying inside the printer and smudging your printouts Disconnect the interface cable from the printer Make sure paper is loaded in the printer 4 Hold down the load eject button and press the 0 power button Hold down the load eject button until the power light starts to flash then release it The printer prints its ROM version number and a nozzle check pattern shown in Running a Nozzle Check on page 10 To end the check turn off the printer Then reconnect the interface cable and turn on your printer and computer EPSON Stylus Scan 2000 Using Special Media Copying without Your Computer Selecting Special Media 1 2 When you print on special media you need to choose the correct Media Type and Paper Size settings in your printer software The table below lists the available EPSON media and the corresponding Media Type setting for each one Media name Media Type setting EPSON 360 dpi Ink Jet Paper 360 dpi Ink Jet Paper EPSON Iron On Cool Peel Transfer Paper EPSON High Quality Ink Jet Paper Photo Quality Ink Jet EPSON
7. power supply 2 Remove the ink cartridges from their packages Then remove only the yellow part of the tape seal on top as shown Ce fos black cartridge color cartridge Caution Use the ink cartridges packed with your printer the first time you install them or your printer won t charge ink properly You must remove the yellow tape from the cartridge or you will permanently damage it Don t pull off the blue portion or try to remove the clear seal from the bottom of the cartridge ink will leak out 3 Lower the printer s output tray and open the front cover 4 Press the power button to turn on the printer The power light flashes and the black and amp color ink out lights come on The print head moves Caution Always use the power button to turn the printer on or off Never use an external switch such as a power strip switch 5 Lift up the color ink cartridge clamp EPSON Stylus Scan 2000 5 EPSON Stylus Scan 2000 6 Place the color cartridge into its holder with the labels facing up and toward the back of the printer Then press down the clamp until it locks into place 7 Press the st cleaning button The print head moves to the left so you can install the black ink cartridge 8 Lift up the black ink cartridge clamp 9 Place the black cartridge into its holder with the labels facing up and toward the back of the printer Then press down the clamp until it locks into place
8. Art Quality Draft amp fast z Resolution 300 7j dpi Scanning a Photo a 12748 Document Size Options s iced C AAS AQ OCRiLine Art Photo ieee ated PET Cas Legal i Quality Best amp de screening M Resolution 300 z dpi M Unsharp Mask File Size 30 64 MB Document Size Auto Scan C A5 C Cad i s T C Letter a gJ Configuration 2 Help Image Type Color Photo lt Close F Black amp White Photo 1 Click the Preview button Your page goes into the scanner es Configuration h Preview 2 Help a Scan A 1 Select Unsharp Mask to sharpen your image automatically 2 Choose your Image Type 3 3 Do one of the following LI Click the Auto Scan button Your photo or page goes in and out of the scanner twice The TWAIN window 2 Close 2 and comes back out The preview image appears on the right side of the TWAIN window Select AAS Auto Area Segmentation or TET Text Enhancement Technology Or select Threshold and move the slider to make your text lighter or darker When your preview looks good click the Scan button Your page goes into the scanner again and comes out slowly as it is scanned closes and your scanned image appears on your screen Related Documentation LI Click the Preview button Your photo or page goes into the scanner and comes back out The preview image TM SCAN2000 EPSON Stylus Scan 2000 Service Manual appears on the right side of the TWAIN window
9. EPSON Stylus Scan 2000 paper edge guide paper feeder paper support document support lt top cover document 7 edge guide output tra output tray p y extensions cleaning load eject reduce enlarge copy mode front ink cartridges cover thickness lever control panel Accessories Ink Cartridges Cartridge Part number Black S020189 Color S020191 User Replaceable Parts Part name Part number Blueberry cover NEED PART NUMBERS Grape cover Lime cover Strawberry cover Tangerine cover DO WE NEED TO LIST THESE PARTS Media Part Media name Size number EPSON 360 dpi Ink Jet Paper Letter S041060 A4 S041059 EPSON High Quality Ink Jet Letter 8041111 Paper A4 S041117 EPSON Photo Quality Ink Jet Letter S041062 Paper A4 S041061 Legal S041067 EPSO atte Paper Letter S041257 Heavyweight EPSON Photo Quality Glossy Letter S041124 Paper A4 S041126 EPSON Photo Quality Glossy Letter S041072 Film A4 S041071 A6 S041107 EPSON Photo Paper Letter 8041141 A4 S041140 4x6 S041134 Panoramic S041145 8 3 x 23 4 inches EPSON Ink Jet Transparencies Letter S041064 A4 S041063 EPSON Photo Quality Ink Jet A6 S041054 Cards 8x10 S041122 EPSON Photo Stickers Kit CD A6 16 frames S041144 KIT ROM and pap
10. Photo Quality Ink Jet Paper Paper EPSON Photo Quality Ink Jet Cards EPSON Photo Quality Self Adhesive Sheets EPSO atte Paper atte Paper Heavyweight EPSON Photo Quality Glossy Paper Photo Paper 3 EPSON Photo Paper EPSON Photo Quality Glossy Film Photo Quality Glossy Film 4 EPSON Photo Stickers 5 EPSON Ink Jet Transparencies nk Jet Transparencies Caution Don t use the cleaning sheets that may be included with your special 6 media they may jam inside the printer Media Loading and Handling Guidelines L Always handle sheets by the edges and don t touch the printable surface L When you load paper make sure the printable side is 7 facing up LJ You can load paper up to the arrow mark on the edge guide LJ Return unused sheets and envelopes to their original 8 package as soon as possible See Paper on page 2 for more storage information LI If your paper package included protective sheets cover the printed side of your paper with these sheets before stacking your paper D Use ink jet papers within one year of purchase Use glossy media and transparencies within six months 9 99 Adjust the edge guides to fit the width of your original Hold the document face down and insert the bottom edge into the scanner edge guides Insert your original face down Make sure the edge guides touch the sides of your original then feed it in until you feel a tug Release the document If you want a smaller or larger copy
11. er EPSON Photo Stickers refill A6 16 frames S041144 EPSON Iron On Cool Peel Letter S041153 Transfer Paper S041155 EPSON Photo Quality Self A4 S041106 Adhesive Sheets Specifications Printing Printing method On demand ink jet Nozzle 144 black nozzles configuration 144 color nozzles 48 cyan 48 magenta 48 yellow Resolution Maximum 1440 x 720 dpi Input buffer 64KB Bidirectional with logic seeking ESC P 2 raster and EPSON Remote Print direction Control code EPSON Stylus Scan 2000 1 EPSON Stylus Scan 2000 Paper Paper type Size Paper types Thickness Weight Single sheets Letter 8 5 x 11 inches Plain paper and special ink jet 0 003 to 0 004 inch 17 to 24 Ib Legal 8 5 x 14 inches Half letter statement 5 5 x 8 5 inches Executive 7 5 x 10 inches A4 210 x 297 mm A5 148 x 210 mm B5 182 x 257 mm papers distributed by EPSON 0 08 to 0 11 mm for plain bond paper 64 to 90 g m Transparencies Glossy film Glossy paper Letter 8 5 x 11 inches A4 210 x 297 mm A6 105 x 148 mm glossy film only Transparencies glossy paper and glossy film distributed by EPSON Self adhesive sheets A4 210 x 297 mm Self adhesive sheets distributed by EPSON Envelopes No 10 9 5 x 4 1 inches 240 x 104 mm Plain bond paper or air mail paper 0 006 to 0 02 inch 12 to 20 Ib DL 8 7 x 4 3 inches 220 x 110 mm 0 16 to 0 52 mm 45 to 75 g m C6 4 4 x 6 4 inches 114 x 162 mm
12. erials to repack the printer 8 Keep the EPSON Stylus Scan level during transport EPSON Stylus Scan 2000 11 EPSON Stylus Scan 2000 S z 4 Ifyou want to crop the image or scan only one section canning click and drag on the preview image Or click the Auto Locate button to automatically 1 Feed in your photo or document as described on page 7 A i outline your photo and eliminate any white border 2 Use the Smart Panel and follow the instructions on the atound it screen Windows only Or follow the instructions below i 4 f 5 Click the e Auto Exposure button to automatically 3 Open an application and select Stylus Scan SF as your adjust scan settings for maximum enhancement of your TWAIN source photo 4 If you re scanning a photograph click the Photo tab If 6 Click the Scan button Your photo or page goes into the you re scanning textora line drawing click the OCR Line scanner again and comes out slowly as it is scanned Your Art tab image opens on your screen behind the TWAIN window 5 Choose Draft amp fast for a quick scan or Best amp de 7 Click the Close button to close the TWAIN window screening for a better quality scan 6 Choose the Resolution setting Scanning Text or Line Art 7 Choose your Document Size AQ OCR Line Art Photo Continue with the steps in one of the next sectios either Scanning a Photo or Scanning Text or Line
13. gin is 0 12 inch 3 0 mm When printing multiple sheets of EPSON Photo Quality Glossy Film the minimum top margin is 1 2 inches 30 mm BL The minimum left margin is 0 12 inch 3 0 mm BR The minimum right margin is 10 inches 28 mm for 10 envelopes 0 28 inch 7 0 mm for DL envelopes 0 12 inch 3 0 mm for all other paper sizes C The minimum bottom margin is 0 55 inch 14 0 mm using the Standard printable area setting This can be decreased to 0 12 inch 3 0 mm using the Maximum printable area setting However the print quality in the expanded printable area may be reduced Note Always load paper into the paper feeder short edge first except envelopes Load envelopes long edge first Ink Cartridges Color ink cartridge S020191 Black ink cartridge Specification S020189 Color s Black Cyan magenta and yellow Print capacity 900 pages text ISO IEC 10561 letter pattern 300 pages graphic 5 coverage 300 pages 5 coverage each color Cartridge life 2 years from production date and up to within 6 months after opening package at 77 F 25 C Storage 4 to 104 F 20 to 40 C emperature 1 month at 104 F 40 C Transit 22 to 140 F 30 to 60 C emperature 1 month at 104 F 40 C 120 hours at 140 F 60 C Freezing 3 2 F 16 C 0 4 F 18 C emperature Dimensions 1 09 W x 2 1 D x 1 5 H 1 7 W x 2 1 D x 1 5 H inc
14. hes inches 27 8 W x 52 7 D x 42 9 W x 52 7 D x 38 5 H mm 38 5 H mm The print capacity may vary depending on how often you clean the print head The ink thaws and is usable after approximately 3 hours at 77 F 25 C Caution To ensure good results use genuine EPSON cartridges and do not refill them Other products may cause damage to your printer not covered by EPSON s warranty Do not use an ink cartridge after the expiration date on the package Mechanical Paper feed method Friction with paper feeder rear entry Paper feeder capacity Maximum 100 sheets of 17 1b 64 g m paper Dimensions Storage Width 17 2 inches 437 mm Depth 15 1 inches 383 mm Height 11 8 inches 300 mm Printing Width 17 2 inches 437 mm Depth 24 3 inches 618 mm Height 11 8 inches 300 mm Weight 16 5 lb 7 5 kg without the ink cartridges Scanning Sheet fed color image scanner Color CCD line sensor 2550 x 4200 pixels 300 dpi 8 5 x 14 inches 216 x 355 6 mm The reading area can be specified from Scanner type Photoelectric device Effective pixels Document size your software 300 dpi main 600 dpi sub 50 to 4800 dpi RGB color filters on CCD Scanning resolution Output resolution Color separation EPSON Stylus Scan 2000 3 EPSON Stylus Scan 2000 Image data Brightness Line art settings Halftoning process Gamma correction Interface Light sou
15. ickly Caution Never turn off the printer while the power light is flashing unless the printer hasn t moved or made any noise for more than 5 minutes The printer moves the print head and begins charging the ink delivery system Even if you don t press the button ink charging begins 60 seconds after you close the clamp The power light flashes and the printer makes various sounds Charging takes about 60 seconds When it s finished the power light stops flashing and stays on 6 Close the front cover Replacing an Outdated Ink Cartridge If an ink cartridge is more than six months old you may need to replace it especially if your printouts don t look as good as they used to If print quality doesn t improve after cleaning and aligning the print head you can replace one or both cartridges Follow these steps to replace an ink cartridge before the black or amp color ink out light is flashing or on 1 Prepare your new ink cartridge for installation as described in steps 1 and 2 of Replacing the Color Ink Cartridge on page 8 2 Make sure the printer is turned on and not printing then lower the output tray and open the front cover 3 Press the load eject button and hold it down for three seconds until the print head moves to the color cartridge replacement position The power light begins flashing Caution To avoid damaging the printer never move the print head by hand Never tur
16. ither flashing or on 1 Remove the new ink cartridge from its packaging 2 Remove only the yellow part of the tape seal on top as shown below black cartridge color cartridge Caution You must remove the yellow tape from the top of the cartridge or you will permanently damage it Don t pull off the blue portion or remove the clear seal from the bottom of the cartridge ink will leak out To avoid damaging the printer never move the print head by hand Lower the output tray then open the front cover 4 Press the st cleaning button and hold it for about three seconds until the print head moves left and the power light begins flashing 8 EPSON Stylus Scan 2000 9 99 5 Pull up the ink cartridge clamp The cartridge rises up from its holder Caution Don t open the clamp or remove a cartridge except to replace it with a new one Once you remove a cartridge you can t reuse it even if it contains ink 6 Lift the cartridge out of the printer and dispose of it carefully WARNING If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water 7 Lower the new ink cartridge into its holder with the label facing up and toward the back of the printer 8 Press down the ink cartridge clamp until it locks in place D A 9 Press the sts cleaning button and release it quickly The printer moves the print head and begins chargi
17. n off the printer while the power light is flashing unless the printer hasn t moved or made any noise for more than 5 minutes 4 Ifyou need to replace the color ink cartridge go on to step 5 below If you need to replace the black cartridge only press the I load eject button again and release it quickly to move the print head to the black cartridge replacement position 5 Remove the old ink cartridge and install the new cartridge as described on page 8 Don t press the s s cleaning button however 6 Press the load eject button and release it quickly The printer moves the print head and begins charging the ink delivery system The power light flashes and the printer makes various sounds Charging takes about a minute When it s finished the power light stops flashing and stays on EPSON Stylus Scan 2000 9 EPSON Stylus Scan 2000 Cleaning the Print Head If your printed image is unexpectedly light or faint or dots are missing from the image you may need to clean the print head This unclogs the nozzles so they can deliver ink properly Cleaning the print head uses ink so clean it only if print quality declines You can clean the print head in either of the following ways L With the Head Cleaning utility when connected to a local port not over a network LJ Using the printer s control panel buttons Using the Head Cleaning Utility 1 Make sure the printer is turned on but not p
18. ng the ink delivery system Even if you don t press the button ink charging begins 60 seconds after you close the clamp The power light flashes and the printer makes various sounds Charging takes about 60 seconds When it s finished the power light stops flashing and stays on Caution Never turn off the printer while the power light is flashing unless the printer hasn t moved or made any noise for more than 5 minutes 10 Close the front cover EPSON Stylus Scan 2000 Replacing the Black Ink Cartridge You can replace a cartridge when the black ink out light is flashing or when it stays on 1 Follow steps 1 through 4 on page 8 Caution Don t open the clamp or remove a cartridge except to replace it with a new one Once your remove a cartridge you can t reuse it even if it contains ink 2 Pull up the black ink cartridge clamp The cartridge rises up from its holder WARNING If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water Keep ink cartridges out of the reach of children 3 Lift the cartridge out of the printer and dispose of it carefully 4 Lower the new ink cartridge into its holder with the label facing up and toward the back of the printer Don t press down on the cartridge 5 Press down the ink cartridge clamp until it locks in place Then press the s cleaning button and release it qu
19. nless the printer hasn t moved or made any noise for more than 5 minutes 3 After the O power light stops flashing print a page to test the print quality and reset the cleaning cycle 4 Run a Nozzle Check examine the check pattern and respond as described below Running a Nozzle Check 1 Make sure the printer is turned on but not printing and the black and amp color ink out lights are off 2 Do one of the following LI Windows Click Start point to Settings then select Printers Right click the EPSON Stylus Scan 2000 icon and select Properties Click the Utility tab 1 Macintosh Open the File menu and choose Page Setup or Print Then click the Utility icon Click the Nozzle Check icon on the Utility menu 4 Follow the instructions on the screen to run the Nozzle Check 5 Examine the nozzle check pattern you print It should look something like this with the lower pattern colored magenta cyan and yellow Each staggered horizontal and straight vertical line should be complete with no gaps in the dot pattern If any dots are missing as shown below clean the print head again see Cleaning the Print Head on page 10 for instructions SEES LI Ifthe nozzle check pattern is complete click Finish Missing dots L Ifthe pattern is missing dots click Clean to run another cleaning cycle LI Ifyou don t see any improvement after cleaning
20. press the Reduce Enlarge button until the size you want is selected The lights indicate the current size setting Press the Copy Mode button to select one of the following Black and white text Black and white photo or image grayscale th Color The lights indicate the current mode setting Press the green Copy button Your original goes into the scanner and then comes back out As it comes out the copy is printed Press the red Stop Clear button to eject your original EPSON Stylus Scan 2000 7 EPSON Stylus Scan 2000 Replacing an Ink Cartridge When the black or amp color ink out light flashes the indicated cartridge is low on ink This is a good time to make sure you have a new cartridge When the light stays on the cartridge is empty and you need to replace it Use these EPSON ink cartridges within six months of installing them and before the expiration date on the package Black ink cartridge 8020189 Color ink cartridge S020191 Caution To ensure good results use genuine EPSON cartridges and do not refill them Other products may cause damage to your printer not covered by EPSON s warranty If you need to replace an ink cartridge before the lights flash because the ink is too old for example follow the instructions in Replacing an Outdated Ink Cartridge on page 9 Replacing the Color Ink Cartridge You can replace a cartridge when the color ink out light is e
21. printer and press the load eject button When the i paper out light comes on your paper ran out or is incorrectly loaded Load paper in the feeder and then press the load eject button bor amp When an ink out light flashes your ink supply is low Make sure you have a replacement cartridge When an ink out light comes on you need to replace the ink cartridge See Replacing an Ink Cartridge on page 8 for instructions e When the scan copy error light comes on a page or photo may be jammed in the scanner Turn off the power open the top cover and remove the jammed document Then close the cover and turn the power back on Qe When the power and i paper out lights flash and the black and amp color ink out lights come on jammed paper may be blocking movement of the print head Turn off the printer open the front cover and remove any paper Then turn it back on When all the lights flash your printer may have an internal error Turn off the power and make sure you removed all the packing material Make sure there is enough space around the rear vent Then turn the power back on Installing an Ink Cartridge for the First Time 1 Plug the printer s power cord into a grounded outlet Caution Don t use an outlet that can be turned off by a wall switch or timer or one on the same circuit as a large appliance This may disrupt the power which can erase the printer s memory or damage its
22. rce 12 bits per pixel per color internal 8 bits per pixel per color external 7 levels Fixed threshold CORRECT Text Enhancement Technology AAS Auto Area Segmentation Printer 3 level A B C User defined 1 level USB 1 0 IEEE 1284 4 White cold cathode fluorescent lamp Interfaces USB interface Specification Description Standard Based on Universal Serial Bus Specifications Revision 1 0 Universal Serial Bus Device Class Definition for Printing Devices Version 1 0 Bit rate 12 Mbps full speed device Data encoding NRZI Adaptable connector USB Series B Reliability Main unit life 10 000 pages Recommended 6 5 feet 2 meters maximum Lamp life 10 000 hours cabis length Electrical Parallel interface Specification 120V model 240V model Forward channel Input voltage range 99V to 132V 198V to 264V Specification Description Rated frequency range 50 to 60 Hz Data format 8 bit parallel IEEE 1284 compatibility mode Input frequency range 49 5 to 60 5 Hz Synchronization Refer to the IEEE 1284 specification Rated current 0 6A 0 4A Handshake timing Refer to the IEEE 1284 specification Power consumption Approx 29 W ISO 10561 Letter Pattern Signal level IEEE 1284 Level 1 device Environmental Temperature Operation 50 to 95 F 10 to 35 C Storage 4 to 104 F 20 to 40 C 1 month at 104 F 40 C Transit
23. rinting and the black and amp color ink out lights are off 2 Do one of the following Q Windows Click Start point to Settings then select Printers Right click the EPSON Stylus Scan 2000 icon and select Properties Click the Utility tab 1 Macintosh Open the File menu and choose Page Setup or Print Then click the X Utility icon Click the Head Cleaning icon 4 Follow the instructions on the screen to clean the print head Cleaning takes about a minute during which the printer makes some noise and the power light flashes When the power light stops flashing continue with the next step Caution Never turn off the printer while the power light is flashing unless the printer hasn t moved or made any noise for more than 5 minutes 5 Make sure paper is loaded and click Print nozzle check pattern Windows or Confirmation Macintosh Then click Next The nozzle check pattern prints see Running a Nozzle Check on page 10 for details Using the Control Panel Follow these steps to clean the print head 1 Make sure the printer is turned on and not printing and that the black and color ink out lights are off 2 Press the st cleaning button and hold it down for three seconds Cleaning takes about a minute during which the printer makes some noise and the power light flashes 10 EPSON Stylus Scan 2000 Caution Never turn off the printer while the power light is flashing u
24. these steps 1 Turn off the printer unplug the power cord and disconnect the printer cable 2 Remove the paper Use a soft brush to clean loose dust and dirt 4 Usea soft clean cloth and mild detergent to clean the outer case and inside of the paper feeder Be careful not to soak the cloth just dampen it Keep the front and top covers closed to prevent moisture from getting inside 5 Open the top cover and clean the scanner glass with a soft dry cloth or with a blower brush 6 Ifink leaks inside the printer wipe it away with a damp cloth Caution Don t touch the gears inside the printer ever use alcohol or thinner for cleaning they can damage the printer components and case Don t use a hard or abrasive brush Don t get water on the printer components Don t spray lubricants or oils inside the printer Transporting the EPSON Stylus Scan If you move your printer some distance you need to prepare it for transportation in its original box Follow these steps 1 Press the O power button to turn the printer off Then unplug the power cord and remove the interface cable 2 Make sure the top cover is closed 3 Remove all paper and then remove the paper and document supports 4 Make sure the output tray is lowered then open the front cover 5 Secure the ink cartridge holder with tape as shown 6 Close the cover and raise the tray 7 Use the original box and packing mat
Download Pdf Manuals
Related Search