Epson AcuLaser C8600 User's Manual
Contents
1. Note for Windows XP users While you install the printer driver the following dialog box may appear If this happens click Continue Anywoy to continue the installation Hardware Installation The software you are installing for this hardware Printers has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now an contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation About an Additional Driver When the printer is shared with some computers clients in a network and the print server s OS is Windows NT 4 0 or Windows 2000 you can install the printer driver for the client s OS in the server as an additional driver This allows the clients to download the appropriate printer driver from the printer serverif necessary See Using an Additional Driver in the Reference Guide for details For Macintosh Users 34 Your Macintosh must meet the following requirements to use the driver included with the printer Mac OS 8 1 to 9 X Note To turn off QuickDraw GX first make sure the Caps Lock key is unlocked Then while holding down the spacebar restart your Macintosh The Extensions Manager will2. 3 Plugthe power cord into a properly grounded electrical outlet 28 Testing and Connecting the Printer Testing the Printer To test whether the printer is set up correctly print a status sheet following the procedures below You will have to first load the MP tray with paper Loading paper Follow these steps to load paper into the MP tray 1 Fanastack of A4 or Letter size paper then tap it on a flat surface to even the edges 2 Load the paper long edge first with the printable surface facing up then set the paper guide as shown below Printing a status sheet Follow these steps to print a status sheet 1 Turnon the printer The lights and the LCD panel messages on the control panel change 2 After the LCD panel shows Eeadu press the Enter button twice The LCD panel shows Status Sheet Testing and Connecting the Printer 29 Press the Enter button again The message on the LCD panel starts flashing and the printer starts printing a status sheet Check that the printer has printed the status sheet clearly and that the information on the options installed in the printer is correct If the printer properly recognizes an installed option the option s name appears under Hardware Configurations If the drive module or interface card is not listed on the status sheet try reinstalling it Make sure that the electronic connector is securely connected to the socket or slot on the circuit board If the total amount
3. States and or other countries Adobe and PostScript are trademarks of Adobe Systems Incorporated which may be registered in certain jurisdictions Apple and Macintosh are registered trademarks of Apple Computer Inc General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners EPSON disclaims any and all rights in those marks Copyright O 2002 by SEIKO EPSON CORPORATION Nagano Japan Warnings Cautions and Notes Warnings must be followed carefully to avoid bodily injury ul Cautions must be observed to avoid damage to your equipment Notes contain important information and useful tips on the operation of your printer ii Safety Instructions Laser Printer Precautions This printer uses laser technology The following precautions apply whenever you use the printer Even if you are familiar with other types of printers be sure to follow these precautions carefully to ensure safe efficient operation Lj E E Because the printer weighs approximately 70 kg 154 lbs without the consumable or optional products installed one person should not lift or carry it Four people should carry the printer lifting it at the correct positions Refer to the instructions in the Unpacking Sheet Be careful not to touch the fuser which is marked CAUTION HIGH TEMPERATURE or the surrounding areas If the printer has been in use the fuser and the su
4. of memory listed does not include the size of the optional memory module try reinstalling the module Make sure that the module is securely attached to the DIMM slot on the circuit board If the printer cannot print a status sheet contact your dealer Connecting to the Computer 30 Use a parallel or USB interface cable to connect your printer to the computer Note If you want to connect the printer to your computer through an installed optional interface card you need a different type of cable See the optional interface card s manual Follow these steps to connect the printer to your computer using the parallel interface Make sure that both the printer and the computer are turned off Testing and Connecting the Printer 2 Attach the parallel or USB interface cable to the printer as shown below ous ae z Note d Usea shielded twisted pair parallel cable or a USB Revision 1 1 compliant cable Q When the cable has a grounding wire secure the wire with the screw below the connector 3 Plugthe other end of the cable into the computer s parallel or USB interface connector See your computer s instruction manual for more information To connect to a network environment have your administrator refer to the Administrator s Guide Testing and Connecting the Printer 31 5 Installing the Printer Software When you install the printer software the following components are installed _J Printer d
5. or exhibits a distinct change in performance D Ifthe printer has been dropped or the cabinet damaged E If the power cord or plug is damaged or frayed J Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage that requires repair by a qualified service representative QJ If you plan to use the printer in Germany observe the following To provide adequate short circuit protection and over current protection for this printer the building installation must be protected by a 10 or 16 amp circuit breaker Safety Information Power cord y Caution Be sure the AC power cord meets the relevant local safety standards Safety Instructions 5 Laser safety labels Your printer is a Class 1 laser product as defined in the IEC 60825 specifications The label shown is attached in countries where required W Warning The use of controls or the performance of procedures and adjustments other than those specified in this guide may result in hazardous radiation exposure LASER KLASSE 1 CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASERLAITE Internal laser radiation Max Radiation Power 5 mW Wave Length 780 nm This is a Class IIIb Laser Diode Assembly that has an invisible laser beam The printer head unit is NOT A SERVICE ITEM Therefore the printer head unit should not be opened under any circumstances An additional laser warni
6. scratch the surface of the photoconductor unit s drum When you remove the photoconductor unit from the printer always set the unit on a clean smooth surface Also avoid touching the drum since oil from your skin can permanently damage its surface and may affect print quality To get the best print quality do not store the photoconductor unit in an area subject to direct sunlight dust salty air or corrosive gases such as ammonia Avoid locations subject to extreme or rapid changes in temperature or humidity Be sure to keep consumable components out of the reach of children Do not leave jammed paper inside the printer This can cause the printer to overheat Important Safety Instructions Read all of the following instructions before operating your printer L Follow all warnings and instructions marked on the printer J Unplug the printer from the electrical outlet before cleaning Use a damp cloth for cleaning Do not use liquid or aerosol cleaners J Do not use the printer near water J Do not place the printer on an unstable surface L Slots and openings located on the front back and top of the printer are provided for ventilation Keep these slots and openings clear to allow proper ventilation Avoid placing the printer on a soft surface like a bed or a sofa or in a small enclosed area as this restricts proper ventilation Safety Instructions 3 Connect your printer to an electrical outlet that meets t
7. steps to install the optional Hard Disk Drive ul Caution Before you install the Hard Disk Drive be sure to discharge any static electricity by touching a grounded piece of metal Otherwise you may damage static sensitive components W Warning Be careful when working inside the printer as some components are sharp and may cause injury 1 Make sure the printer is not turned on and that the power cord is unplugged Installing Options 2 Prepare the printer as shown below to access the Hard Disk Drive socket u A SV V y 19 Installing Options 3 Identify the Hard Disk Drive socket 4 Install the Hard Disk Drive securely with the screws ul Caution You should not remove any modules from the circuit board Otherwise the printer will not work 5 Connect the two connectors of the cable as shown below 20 Installing Options T 6 Lower the two clamps to insert the cable then raise the clamps 7 Return the printer to its original state as shown below La Oj 21 Installing Options 8 Plug the printer s power cord into an electrical outlet 9 Turnon the printer 10 To confirm that the Hard Disk Drive is installed correctly print a status sheet See Printing a status sheet on page
8. 29 Installing a Memory Module 22 Increasing the printer s memory allows you to print complex or graphics intensive documents You can increase printer memory up to 1 GB by installing optional Dual In line Memory Modules DIMMs This printer has two DIMM slots but one slot has a 64 MB DIMM already installed in it at the time of manufacture To increase printer memory to its maximum of 1 GB you have to purchase two 512 MB DIMMs and remove the original 64 MB DIMM You can purchase DIMMs from various vendors Be sure they meet the following requirements DRAM type synchronous Dynamic RAM Dual In line Memory Module SDRAM DIMM Memory size 64 128 256 or 512 MB Type 168 pin type 64 bit with SPD Clock frequency 100 MHz or higher 10 ns or less CAS Latency Clez2 Height Less than 40 mm SPD stands for Serial Presence Detect a chip residing on the memory module that contains information about the size soeed and other specifications of the memory as well as manufacturer information that can be retrieved by the motherboard through electronic signals Installing Options Follow these steps to install an optional memory module ul Caution Before you install a memory module be sure to discharge any static electricity by touching a grounded piece of metal Otherwise you may damage static sensitive components W Warning Be careful when working inside the printer as some components are sharp and may cause inj
9. EPSON Color Laser Printer EPSON AcuLaser C8600 Guide 4021253 00 EUL Where fo Find Information Setup Guide this manual Contains information on placing and assembling the printer and installing the printer driver User Guides The CD ROM shipped with your printer includes the following guides as well as the printer driver Note Microsoft Internet Explorer 4 0 or later or Netscape Navigator 4 0 or later must be installed on your computer to view the Reference Guide and the Administrator s Guide Adobe Acrobat Reader 4 0 or later must be installed on your computer to view the Quick Reference Reference Guide HTML L How to use the printer _1 How to solve problems J How to keep your printer in good condition Q Safety information and technical specifications Aaministrator s Guide HTML Provides network administrators with information on both the printer driver and network settings Quick Reference PDF Provides you with a list of LCD panel messages solutions for paper jam problems and other information about your printer that you may need to refer to on a regular basis We recommend printing the guide and keeping it near the printer Color Laser Printer EPSON AcuLaser C8600 Setup Guide Safety IDSITHCTIOPIS ince aduaco 9d E R3 2 Assembling the Printer s 3 Installing ODIOPBS 2 eur dax x ms ea 4 Testing and Connecting the Printer 5 Inst
10. alling the Printer Soffware 6 Printing the Quick Reference Guide All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means mechanical photocopying recording or otherwise without the prior written permission of SEIKO EPSON CORPORATION No patent liability is assumed with respect to the use of the information contained herein Neither is any liability assumed for damages resulting from the use of the information contained herein Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding the U S failure to strictly comply with SEIKO EPSON CORPORATION s operating and maintenance instructions SEIKO EPSON CORPORATION and its affiliates shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION EPSON and EPSON ESC P are registered trademarks and EPSON AcuLaser and EPSON ESC P 2 are trademarks of SEIKO EPSON CORPORATION Microsoft and Windows are registered trademarks of Microsoft Corporation in the United
11. amage from condensation You need to install four toner cartridges into the printer Follow these steps to install the toner cartridges Assembling the Printer 11 1 Open the front cover 2 Check the color in the cartridge installment window and prepare the cartridge of the same color Cyan Yellow Magenta This color indicator represents the toner cartridge color 12 Assembling the Printer 3 Take the cartridge out of its package and gently shake it 4 Insert the toner cartridge all the way until it stops 5 Turn the cartridge knob as shown below E3 Caution Be sure to turn the knob all the way to the locked position Otherwise you may have toner problems or leakage Assembling the Printer 13 6 Push up the switch located at the upper left then release it 7 Turn the upper knob clockwise until it stops The switch automatically drops down and the next empty cartridge slot appears Note If the knob cannot be moved first check that the switch is in the upper position Do not force the knob 8 Install the other cartridges as described in steps 2 to 7 skip steps 6 and 7 for the last cartridge 9 Next install the photoconductor unit as described in the following section 14 Assembling the Printer Installing the Photoconductor Unit Handling precautions L When installing the photoconductor unit avoid exposing it to room light a
12. he power requirements of this printer Your printer s power requirements are indicated on a label attached to the printer If you are not sure of the power supply specifications in your area contact your local power company or consult your dealer The interface connector for this printer is Non LPS non limited power source If you are unable to insert the AC plug into the electrical outlet contact an electrician Do not put your printer where the cord will be stepped on Avoid sharing outlets with other appliances When using an extension cord be careful not to exceed its recommended amperage limit Also be sure that all items plugged into the electrical outlet do not exceed a total of 15 amperes Never push objects of any kind through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill liquid of any kind onto the printer Unless specifically instructed in this guide do not attempt to service this product yourself Opening or removing those covers that are marked Do Not Remove may expose you to dangerous voltage points or other risks Contact a qualified service representative for service Safety Instructions L Unplug the printer and contact a qualified service representative under the following conditions A If liquid has entered the printer B If the printer has been exposed to rain or water C If the printer does not operate normally
13. ire must be connected to the terminal in the plug marked with the letter N L The brown wire must be connected to the terminal in the plug marked with the letter L If damage occurs to the plug replace the cord set or consult a qualified electrician Replace fuses only with a fuse of the correct size and rating Safety Instructions 9 2 Assembling the Printer Before assembling the printer follow the instructions on the Unpacking Sheet to remove all protective materials packed around and inside your printer Note Keep all packing materials as you will need them when transporting the printer Installing the Face Up Tray Follow these steps to install the face up tray onto the left side of the printer 1 Locate the output slot on the left side of the printer 2 Install the face up tray as shown below Ea Caution Do not insert the metal spring into the output slot or any holes in the printer case Doing so may damage the face up tray or your printer metal spring 10 Assembling the Printer Installing the Toner Cartridges Before installing the toner cartridges read the following handling precautions J Do not install used toner cartridges into the printer L If toner gets onto your skin or clothes wash it off with soap and water immediately L Wait for at least 1 hour before installing a toner cartridge after moving it from a cool to a warm environment to prevent d
14. mpers on the card as necessary 5ee the interface card s manual for details 3 Remove the screws as shown below and remove the cover Note Keep the slot cover in a safe place You will need to reattach it if you remove the interface card later Installing Options 4 Slide and push the interface card into the slot firmly then fasten the screw as shown below A amp sj o 5 Plug the printer s power cord into an electrical outlet 6 Turnon the printer 7 To confirm that the interface card is installed correctly print a status sheet See Printing a status sheet on page 29 Installing Options 27 4 Testing and Connecting the Printer This chapter provides you with the necessary instructions on how to connect the printer to your computer Plugging in the Printer Follow these steps to connect the printer to an electrical outlet 1 Check the label on the printer to make sure that the voltage required by the printer matches the electrical outlet Also make sure that you have the correct power cord for your power source ul Caution It is not possible to change the printer s voltage If the required voltage and your outlet voltage do not match contact your dealer for assistance Do not plug in the power cord 2 Make sure that the printer is turned off Connect the power cord to the AC inlet on the left side of the printer
15. ng label is affixed to the inside of the printer CDRH regulations For information about the Center for Devices and Radiological Health of the U S Food and Drug Administration see the Reference Guide on the CD ROM 6 Safety Instructions Ozone safety Ozone emission Ozone gas is generated by laser printers as a by product of the printing process Ozone is produced only when the printer is printing Ozone exposure limit The recommended exposure limit for ozone is 0 1 parts per million ppm expressed as an average time weighted concentration over an eight 8 hour period The EPSON AcuLaser C8600 laser printer generates less than 0 1 ppm for 8 hours of continuous printing Minimize the risk To minimize the risk of exposure to ozone you should avoid the following conditions L Use of multiple laser printers in a confined area see above QJ Operation in conditions of extremely low humidity LI Poor room ventilation L Long continuous printing together with any of the above Printer location The printer should be located so that the exhaust gases and heat generated are J Not blown directly into the user s face L Vented directly out of the building whenever possible Safety Instructions 7 For United Kingdom Users The EPSON AcuLaser C8600 is a page printer which utilizes a semiconductor laser There is no possibility of danger from the laser provided that the printer is operated according to the instr
16. ny longer than necessary J Keep the photoconductor unit out of the reach of children Follow these steps to install the photoconductor unit 1 Take the photoconductor unit out of its package and unwrap the protective sheet while holding the handle ul Caution d Be sure not to touch or scratch the surface of the drum Q Avoid touching the drum since oil from your skin may permanently damage its surface and affect print quality Assembling the Printer 15 2 Turn the lever as shown below 3 Insert the photoconductor unit as shown below Note Make sure that the unit is completely inserted into the slot 16 Assembling the Printer 4 Turnthe two levers as shown below 5 Close the front cover wW Warning Do not dispose of used photoconductor units in fire as they can explode and cause injury Dispose of them according to local regulations Assembling the Printer 17 3 Installing Options If you purchased any options with the printer install them before plugging in the printer To install an optional paper cassette or optional Duplex Unit follow the instructions on the product package Installing the Hard Disk Drive 18 The optional Hard Disk Drive allows you to expand the printer s receive buffer when using a network and gives you additional memory for graphics and faster multi page multi output sorting Follow these
17. open Clear the QuickDraw GX check box then close the Extensions Manager Installing the Printer Software ul Caution Turn off any anti virus software before installing the printer driver Make sure that the printer is turned off Insert the CD ROM that comes with your printer into your CD ROM drive Double click the Install Software folder pP d Pearl Set Pro Double click the Installer icon Installer Click Continue When the software license agreement screen appears read the statement and then click Accept Click Install and follow the on screen instructions Installing the Printer Software 35 Selecting your printer in The Chooser 36 After you have installed the printer driver you need to open the Chooser to select your printer This procedure is necessary the first time you use a printer and when you want to switch to another printer Your Macintosh will always print using the last printer selected AppleShare AppleTalk Zones Installing the Printer Software AppleTalk 0 Chooser m B Select a printer port USB Port 2a sa amp Active Q Inactive 762 Printing the Quick Reference Guide After you install the printer driver print the Quick Reference guide included on the printer software CD ROM The Quick Reference guide describes how to clear paper jams and other common problems Note Acrobat Reader 4 0 or la
18. rces Bldg 26 Harbour Road Wanchai Hong Kong Phone 2585 4300 Fax 2827 7083 EPSON ITALIA S p A V le F lli Casiraghi 427 20099 Sesto S Giovanni MI Italy Phone 43902262331 Fax 439022440750 SEIKO EPSON CORPORATION Hirooka Office 80 Harashinden Hirooka Shiojiri shi Nagano ken 399 0785 Japan EPSON UK LTD Campus 100 Maylands Avenue Hemel Hempstead Herts HP2 7TJ U K Phone 44 01442 261144 Fax 444 01442 227227 EPSON FRANCE S A 68 bis rue Marjolin 92300 Levallois Perret France Phone 33 1 41 86 26 56 Telex 610657 EPSON SINGAPORE PTE LTD No 1 Temasek Avenue 36 00 Millenia Tower Singapore 039192 Phone 065 633 77 911 Fax 065 633 41 185 EPSON TAIWAN TECHNOLOGY amp TRADING LTD 10F No 287 Nanking E Road Sec 3 Taipei Taiwan Phone 02 2717 7360 Fax 02 2712 9164 EPSON IBERICA S A Av de Roma 18 26 08290 Cerdanyola del Valles Barcelona Spain Phone 582 15 00 Fax 582 15 55 EPSON PORTUGAL S A R do Progresso 471 1 Perafita 4460 Matosinhos Portugal Phone 02 996 14 02 Fax 02 996 14 11 2002 January EPSON Color Laser Printer EPSON Aculaser C8600 Setup Guide
19. river A printer driver for Microsoft Windows XP Me 98 95 2000 and Windows NT 4 0 and for the Macintosh is provided This software lets you make a variety of settings such as print quality and paper size _J EPSON Status Monitor 3 The EPSON Status Monitor 3 utility allows you to view printer status information such as the amount of toner remaining and to check for any printer errors To install the printer software follow the instructions for Windows or for Macintosh in this section For Windows Users 1 Make sure that the printer is turned off 32 Installing the Printer Software 2 Insert the CD ROM that comes with your printer in your CD ROM drive The following screen appears EPSON Installation Program Please select from the following items om User Guides al Install Printer Driver Utility d B Install EPSON BarCode Font dB ec Install EPSON Font Manager Aol g t gt A a m T d e z v Ss 7 z 8 g9 e 5 3 D x D n 5 3 i T D 2 z i D 2 rJ B 3 Hd E 5 p Note If the EPSON Installation Program screen does not appear automatically double click the My Computer icon right click the CD ROM icon and click Open in the menu that appears Then double click Setup exe 3 Double click Install driver utility 4 Follow the on screen instructions Installing the Printer Software 33
20. rrounding areas may be very hot CAUTION HIGH TEMPERATURE Do not insert your hand into the fuser unit Do not insert your hand into the fuser unit as some components are sharp and may cause injury Avoid touching the components inside the printer unless instructed to do so in this guide Safety Instructions 1 Never forcethe printer s components into place Although the printer is designed to be sturdy rough handling can damage it When handling toner cartridges always place them on a clean smooth surface Do not attempt to modify toner cartridges or take them apart They cannot be refilled Do not touch the toner Keep the toner away from your eyes Do not dispose of used toner cartridges waste toner collectors or photoconductor units in fire as they can explode and cause injury Dispose of them according to local regulations Wait at least one hour before using a toner cartridge or a photoconductor unit after moving it from a cool to a warm environment to prevent damage from condensation When removing the photoconductor unit avoid exposing it to light for more than 5 minutes The unit contains a blue colored light sensitive drum Exposure to light can damage the drum causing dark or light areas to appear on the printed page and reducing the service life of the drum If you need to keep the unit out of the printer for long periods cover it with an opaque cloth Safety Instructions Be sure not to
21. ter as shown on page 19 to access the slot Installing Options 3 Identify the ROM slots ROM slots 4 Insert the module firmly into slot A or B as shown below J Ea Caution Q Do not force the ROM module into the slot 1 Be sure to insert the module facing the correct way Q You should not remove any modules from the circuit board Otherwise the printer will not work 5 Return the printer to its original state as shown on page 21 6 Plug the printer s power cord into an electrical outlet 7 Turnon the printer 8 Toconfirm that the ROM module is installed correctly print a status sheet See Printing a status sheet on page 29 Installing Options 25 Installing an Interface Card 26 Your printer comes with a Type B interface slot Various optional interface cards are available to expand your printer s interface options Note Mac OS 8 5 1 to 9 X supports the Type B IEEE 1394 Interface Card C12C82372s It can be connected to a Macintosh FireWire port Follow these steps to install an optional interface card ul Caution Before you install the interface card be sure to discharge any static electricity by touching a grounded piece of metal Otherwise you may damage static sensitive components 1 Make sure the printer is not turned on and that the power cord is unplugged 2 Besure to set any switches and ju
22. ter must be installed on your computer to open and read the Quick Reference guide For Windows users 1 Insert the CD ROM that comes with your printer in the CD ROM drive 2 Double click User Guides in the EPSON Installation Program screen 3 Click the arrow next to View Quick Reference The Quick Reference guide opens 4 Select Print from the File menu and click OK The Quick Reference guide will be printed Store the printed Quick Reference guide near the printer Printing the Quick Reference Guide 37 For Macintosh users 1 Insert the CD ROM that comes with your printer in the CD ROM drive 2 Double click the User Guides folder in the EPSON folder mm as us User Guides 3 Double click the View Quick Reference icon in the User Guides folder The Quick Reference guide opens View Quick Reference 4 Select Print from the File menu 5 Click Print The Quick Reference guide will be printed Store the printed Quick Reference guide near the printer 38 Printing the Quick Reference Guide EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA INC 3840 Kilroy Airport Way Long Beach CA 90806 Phone 562 981 3840 Fax 562 290 5220 EPSON DEUTSCHLAND GmbH Z lpicher StraBe 6 40549 D sseldorf Germany Phone 0211 56030 Fax 0211 5047787 EPSON AUSTRALIA PTY LTD 70 GIBBES STREET CHATSWOOD 2067 NSW Phone 2 9903 9000 Fax 2 9903 9177 EPSON HONG KONG LTD Rooms 4706 10 47 F China Resou
23. uctions in the guides provided Since radiation emitted by the laser is completely confined within protective housings and external covers the laser beam cannot escape from the machine during any phase of user operation W Warning The use of controls or the performance of procedures and adjustments other than those specified in this guide may result in hazardous radiation exposure This is a semiconductor laser The maximum power of the laser diode is 5 mW and the wavelength is 780 nm Use of options Epson UK Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Epson UK Limited Safety information 8 Warning This appliance must be earthed Refer to the rating plate for voltage and check that the appliance voltage corresponds to the supply voltage Important The wires in the mains lead fitted to this appliance are coloured in accordance with the following code Safety Instructions Green and yellow Earth Blue Neutral Brown Live If you need to fit a plug As the colours of the mains lead of this appliance may not match any coloured markings used to identify the terminals in a plug please proceed as follows L The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or the Earth symbol J The blue w
24. ury 1 Make sure the printer is not turned on and that the power cord is unplugged 2 Prepare the printer as shown on page 19 to access the slot 3 Identify the DIMM slots DIMM slots 4 Insert and push the DIMM into either slot The two clips lock onto the DIMM N K N X N N N N N N E S Installing Options 23 Y Caution Q Do not force the DIMM into the slot L Be sure to insert the DIMM facing the correct way Q You should not remove any modules from the circuit board Otherwise the printer will not work 5 Return the printer to its original state as shown on page 21 6 Plugthe printer s power cord into an electrical outlet 7 Turnon the printer 8 To confirm that the memory module is installed correctly print a status sheet See Printing a status sheet on page 29 Installing a ROM Module 24 The optional ROM modules that expand your printer s features differ depending on the country of purchase Follow these steps to install an optional ROM module ul Caution Before you install a ROM module be sure to discharge any static electricity by touching a grounded piece of metal Otherwise you may damage static sensitive components W Warning Be careful when working inside the printer as some components are sharp and may cause injury 1 Make sure the printer is not turned on and that the power cord is unplugged 2 Prepare the prin
Download Pdf Manuals
Related Search