Epson 16:10 Height-Adjustable Cart Solution Assembly Guide
Contents
1. Epson wi E pson Mobile Cart for Epson ultra Short Throw Projectors Assembly Guide 470 475W 475W 480 480 485W 485Wi For assistance please contact us Epson CART 2012 A Copernicus This Assembly Guide provides instructions 4 800 267 8494 to build the Epson Mobile Cart for Epson Ultra Short Throw Projectors soe products Email info copernicused com Have your packing slip ready for reference Optional Lock Box CEPCART3 e i H Optional Rear Laptop amp Keyboard Tray CEPCART4 Base Frame CEPCART1 or 2 Check out some of our Need Tech Support other great products Have a Question Please Recycle Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Epson i E pson Mobile Cart for Epson ultra Short Throw Projectors Assembly Guide 470 475W 475W 480 4801 485W 485Wi For assistance please contact us Epson_CART_2012_A This Assembly Guide provides instructions 4 _ 3 z Coperricus to build the Epson Mobile Cart for Epson 1 800 267 8494 r Ultra Short Throw Projectors Email info copernicused com Have your packing slip ready for reference Table of Contents Tips for FS SCION cesta ae cc es teen eer eey adeee eee egetacttene er AiE os eaceeneedeepesseseeteneesece 3 Frequently Asked QUESTIONS cccceccceecceeeceeeceeecee cece eeseeeseeeseeeeeeeesaeeseeseeesees 4 EURE ae P ee ee E ee ee 5 Assemble the Base Frame CEPCART 12. Install Optional Side Laptop Arm Skip this step if you are not installing the side laptop arm TIGHTEN 28 WARNING To avoid property damage or bodily injury please hold the board securely until fastened Position Board on Mounting Frame Lift board onto the bottom mounting frame resting it on the bottom brackets One person should hold the top of the board until it is secured next step Loosen nut and slide bracket until it is flush with the board Once it is flush re tighten the nut in place 29 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc re CMM S 4x 35mm bolt 4x You will need not to scale Top clamps x 2 Secure Top of Board Position top clamp around top frame of board 3 m a J Po Loosen nut and slide bracket until it is flush with the board Once it is flush re tighten the nut in place 30 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Adjust Projector Arm Height Install using the bottom two holes on the post All the supported projector and board combinations will use these same post holes Epson Projector Arm Projector Model Board PA Post Epson 470 480 Smart 680 470 480 Smart 880 475W 485W Smart 685 475W 485W Smart 885 475WI 485WI Copernicus 77 WB 480l Copernicus 77 WB 475W1 485WI Egan 90 WB 475W1 485WI
3. LL ranere MW Mi32 Q O ox vee 50mm bolt FF 26 aa a flat ol Ummm ypas Partially threaded M10 x 55mm bolt 2x M10 lock n 7H LLL with last inser i mee P M6 keps n Ait mI o h al readd M6 x 65mm tot i oC Re a O its rtially threaded M8 x 95mm bolt Oo etree stic pi coon O tage space O z 90mm bolt u M8 flat front side O Iil washer Partially threaded M8 x 35mm bolt 8x O inn O meote Wizoeein SVINI 7 R Mex omm tot Me x 50mm Shoulder Bok LLL L M6 x 35mm bolt BB 2x artal dreaded M8 x S0mm tot VINNUNNI Epson ea Epson Mobile Cart Options Before beginning you should have Z Contents Optional Lock Box cercarrs Sm ANN Lock box Sine Lock box go with door s stretcher 2 N Z B 2x A 1 left 1 right N M6 lock washer Ms x 13mm M6x S M6x ey FD bolt 5Omm 4x No 35MM ss 4x bolt bolt P Z x x 7I _ s s A r o o r ue keps nut am lock r O parre nut s s s a Optional Rear Laptop Arm amp Keyboard Tray cercarrs Contents Rear laptop tray Keyboard tray oe nut Y lock w _ bot mi Optional Side Laptop Arm cercarrs Contents Laptop extension Side laptop tray arm 1x 1x Z R M8 lock nut c x 40mm Lum bolt 2x Epson_CART Version 2012_A May 8 2012 Copernicus Educational Prod
4. catch on the cylinder and then snap the body of cable into the fitting on the cylinder MAKE SURE IT SNAPS INTO PLACE IT IS A VERY TIGHT SNAP FIT Release cable runs up behind the board from the front of the unit Front TIGHTEN ALL FASTENERS ON THE UNIT 45 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc TIGHTEN ALL FASTENERS ON THE UNIT Release Height Stop Pin To allow height adjustment of the unit pull the detent pin out of the locator hole At any time replace the pin in the hole to stop the unit from adjusting in height Pull pin out of hole WARNING Gas Cylinder is under pressure To avoid property damage or bodily injury please ensure unit is fully assembled before adjusting the height 46 Epson_CART Version 2012 _A May 8 2012 Copemicus Educational Products Inc x Setting Up the Projector for Use Please refer to the Epson installation guide included with your projector for details on setting up the projector and aligning the projector for use Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 47 Black one wrap Velcro strap 12x You will need not to scale Split black wire loom 1x Routing Cables Through the Cart Q VGA cable provided with projector VGA cable amp power projector cord run through the Project bl projector setting plate Plug both c
5. ANNWW F ane welded nuts are facing toward the front l i 21 x You will need not to scale Board mounting frame bottom x 1 Determine Your Board Frame Position Epson Projector Arm The board mounting frame is adjustable to Projector Model Board allow for the use of different sizes of boards J Epson 470 480 Smart 680 470 480 Smart 880 Use this table to determine which hole Peer Raat E you should use 475W 485W Smart 885 475W1 485WI Copernicus 77 WB 4801 Copernicus 77 WB 475W1 485WI1 Egan 90 WB 475W1 485WI1 Egan 96 WB Hole A Hole B Hole C Hole D Hole E Hole F Hole G Hole H Tip for verifying your hole position Distance X Board Frame Shown installed in Hole H 22 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 12 NY un QOL M6 x 90mm bolt 2x 2x front side You will need not to scale U M8 flat washer 2x Board mounting frame bottom x 1 Install Board Mounting Frame Bottom Using the hole you selected on the previous page slide the bottom mount frame into the top mount frame and fasten through your chosen hole and through the sliding frame as shown Tap in with rubber mallet if necessary Work from side gt to side as you tap it in TIGHTEN 23 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Produ
6. Side Laptop Arm Lubrication Instructions 1 Remove arm by lifting it up vertically 2 Apply Petroleum Jelly all around the connector 3 Install arm back onto the connection Apply Petroleum Jelly Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc
7. laptop tray assembly onto support stretcher until the spring clips pop through the laptop tray assembly CAUTION Maximum recommended weight on rear laptop arm 20 Ibs Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc q 0 Actual Size R M8 lock nut 4x You will need not to scale ee ee Board mounting frame top x 1 Board mounting frame support x 2 Install Board Mounting Frame Top amp Projector Arm Support 7 LEAVE VERY LOOSE Ensure tabs are all on one side 20 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Ol WN M8 x 95mm bolt 1x 2 Person Task You will need not to scale Projector arm support x 1 Ww J oOoO M8 lock M8 x 65mm bolt 1x Install Board Mounting Frame Top amp Projector Arm Support me Note orientation of arm ensure it is toward the front You must remove the temporary bolt and detent pin to install the arm support Ensure frame is level before tightening Rear Spacer item T Slide projector arm support into center slide pole Insert bolts through the projector support arm shock bracket and board mounting frame top Tap in with a rubber mallet if necessary AO ons Ome x TR AET Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Large front _ spacer 2x
8. 8 2012 Copernicus Educational Products Inc l gt fal M o ag CO AAA You Wil need qaru coan m gt eed 6 x 35mm bolt 2 M8 lock washer 4x M6 barrel nut S a Install Front Cover amp Short Stretchers DOE Ss If you plan to install the optional Lock Box wssher2x Viii O skip this step and proceed to Step 7B for instructions Short stretcher x 2 Front cover x 1 a a a ae O a E O LQ You will need not to scale g Short stretcher x 2 bolt 1x Small N 1X front Front cover x 1 Install Front Cover amp Short Stretchers If you plan to install the optional Lock Box Item Q spacer sits between front cover and base assembly tubing Front i fig Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc os 2OL side flat washer 2x d ll 2 OSO ie ce a Co Back supports x 2 Install Back Supports amp Secure Short Stretchers Hole indents should always be to the outside of the unit Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc JTD ANNAN 2 bolt 2x 2x You will need not to scale Option You will need not to scale Laptop tray x 1 P Support stretcher with spring clips chrome x 1 Ensure spring clip is turned towards the inside of the unit Laptop tray can be installed on either the left or right hand side Slide
9. Egan 96 WB arm until the projector E has been installed i DO NOT fold projector TIGHTEN BOLTS NOW Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 31 20 1 You will need not to scale Adapter Plate x 1 Epson Projector Arm x 1 Install Projector Arm Adapter Plate Remove four screws and washers Keep for later step Hold the two mount pieces together so that the Slots in each align Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc a2 4x washer 6x 20 2 Actual Size V E5 FP J M8 flat washer M4 x 16mm bolt ANY M4 lock washer 9 16 x 11 64 flat 0 6x 6x While holding the two mount pieces together and holding in place the hexagonal shaft install the four screws you kept along with the added washer Do not fully tighten all the way until after you mount the arm on the Projector Support Arm that was included 4 Install six short screws lock washers and flat washers Do not tighten the 6 screws with your Cart or Wall Mount Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc M10 lock nut 2x 21 Actual sze O O V N 2 Person Task K flat washer me lock washer cm bolt TT You will need not to scale Epson Projector Arm with Adapter Plate x 1 Attach Projector Arm to Unit TIGHTEN these nuts Hook a
10. Watch for this symbol throughout the Assembly Guide Wherever you see it pay close The star symbol highlights an advisory note Before You Begin As You Assemble the Unit Lay out and identify all of the included parts The hardware has been packed according to step Read the assembly guide over once to familiarize yourself with them Please note that in its unassembled state this product contains parts that can be hazardous to small children This product should be assembled by an adult Follow the steps in sequence q Before beginning each step find the part s that you need for that step Pay attention to the labels on the parts they are there to help direct you at certain stages The title of each step states what you will be doing Review the text and the pictures as you build the unit Some holes have indented the tubing These holes are marked with a red dot sticker Anywhere there is an indent or red dot sticker it should face towards the outside of the unit See image below C C l Hole indents should L always be to the outside lt gt KY a Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Customer Service FAQs 4 fa a For missing parts and other issues regarding the frame The height adjust system is not working The gas cylinders are not working properly I lost the key to my lock box Please call Copernicus Customer Servi
11. ce where we will be happy to help Have a Question 1 800 267 8494 Monday Friday 8 00am 4 30 pm EST My interactive board isn t working who should I call Please call the reseller that you bought the product from first reseller information can be found on your packing slip My projector isn t working who should I call Please call the reseller that you bought the product from first reseller information Need Tech Support Oba of Email our Tech Support Service can be found on your packing slip OR please call Epson Customer Service at United States 562 276 4394 or Canada 905 709 3839 Dear Educator Thank you for purchasing one of our products I hope the assembly of your Epson Mobile Cart went well If you have any questions or concerns or ideas for how we can improve please call us at 1 800 267 8494 where someone will be happy to help Enjoy using your new product and happy teaching Jim Phillips President Quality schools are the result of quality teachers going above and beyond the call of duty VICKI CARUANA A liberal education is at the heart of a civil society and at the heart of a liberal education is the act of teaching A BARTLETT GIAMATTI Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc My idea of education is Develop a passion for to unsettle the minds of learning If you do you the young and inflame will never cease to g
12. cts Inc BS u IMM oo O M8 x 35mm bolt 4x 4x You will need not to scale Lift handle x 1 5 Install Lift Handle TIGHTEN 24 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc O ANNI On O Pen You will need not to scale y Keyboard tray x 1 Install Optional Keyboard Tray Skip this step if you are not installing a keyboard tray 25 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc OO L hua M8 lock washer M6 barrel nut 8x 8x B Protective handle x 2 Handle insert x 4 You will need not to scale Install Protective Handles If you plan to install the optional Side Laptop Arm skip this step and proceed to step 15B for instructions TIGHTEN Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc mu 26 a r aie en int Sn bolt 6x Protective handle x 2 Handle insert x 4 You will need not to scale Install Protective Handles for Use With a Side Laptop Arm If you plan to install the optional Side Laptop Arm Do not secure handle on the lower right side from Front of the unit This is where your side laptop arm will be installed Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc W M6 barrel nut mu 2 Actual Siz SAN Cumo You will need no Side a extension arm x 1
13. dapter plate over studs on projector arm Hold arm in position a a l WARNING Gas cylinders are under pressure To avoid property damage or bodily injury please use caution when folding the arm z P Rotate adapter plate into position and secure Please refer to the installation guide included with your Epson projector for instructions on how to install the projector on the adapter plate and on how to adjust the projector for use Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 34 Remove Slide Plate Remove the two screws Keep your hardware for the next step A G i You will need not included not to scale Epson projector x 1 PowerLite 470 480 480i 475W 485W 475Wi 485VWVi Attach Slide Plate to Projector Use the hardware supplied Attach the Slide Plate to the projector A with your projector 36 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Attach Projector to Projector Arm Use the hardware supplied with your projector 37 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Actual Size J S he used only in special instances M8 x 50mm shoulder M6 lock nut bolt 1x 4x Install Stop Bolt All the projector and board combinations listed in this assembly guide require a stop bolt to be installed This bolt is int
14. e N Insert slide handle in end of slide frame Ensure slide handle is on the left side of the unit Insert assembly over the legs Ensure both sides have a black plastic bushing in the top Please Note Sliding parts are lubricated with a Petroleum based jelly to ensure smooth movement when adjusting the height 13 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc O a C Tm L 2x You will need not to scale Center slide pole x 1 Install Center Slide Pole Install bolt in circular hole first and then in oblong hole Tap in with rubber mallet N if necessary D 14 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc ooo NINN hardware bag 1x You will need not to scale Upper frame pre assembly x 1 Install Upper Frame Insert upper frame into the legs ensuring that the center slides over the center slide pole Pull frame up Tap in with rubber to align holes mallet if necessary Use a spare bolt or Velcro Strap included to secure the upper frame to the Pa s se center slide pole until the top is fastened Insert detent pin attached to upper frame a Sa in hole Please Note Sliding parts are lubricated with a Petroleum based jelly to ensure smooth movement when adjusting the height Epson_CART Version 2012_A May
15. ended to fit tight You may need to tap the bolt in using a rubber mallet C Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 3 8 Folding the Projector Arm WARNING Gas cylinders are under pressure To avoid property damage or bodily injury please use caution when folding the arm Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 39 ow Ea O Qo F5 You will need not to scale ANN M6 x 35mm bolt 2x Lock box side with doorx 2 Wa 1 left 1 right Install Optional Lock Box Sides CAUTION Maximum recommended weight in lock box 50 Ibs 40 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc O ANNAN O Lock box top x 1 You will need not to scale Install Optional Lock Box Top Position the lock box top around the support stretcher with the sheet metal tab between the stretcher and the front cover Side tabs on the top fit inside of the box sides It is easiest to fit the edges towards the back doors of the unit between the doors first and then push the front side into place Fij Image shown with door removed for clarity CAUTION Maximum recommended weight in lock box 50 Ibs 4 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc ee a gt oa NNN V keps w e O xX ead bolt kep
16. ock box side with door 2 1 left 1 right Optional Rear Laptop Arm amp Keyboard Tray CEPCART4 Laptop tray 1 Optional Side Laptop Arm CEPCARTS a S SE pen a Laptop tray 1 J i E Laptop rotation arm 1 Laptop extension arm 1 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 6 Epson ia Epson Mobile Cart Base Frame Before beginning you should have ag arm Center support slide Leg Back ms ies 2x support 2x a stretcher Bottom cover Front cover 1x 1x Board mounting Board mounting Handle frame top frame support insert 1x 2x Top clamp 2X Board mounting E frame bottom g 1x Wrenches 2 of Each 10mm 13mm 17mm 19mm OR Two adjustable wrenches vA aor PETT PPr Hardware on following page Contents Box 1 CEPCARTO Support stretcher grey Slide frame 1x chrome Velcro strap 12x Split black 4 swivel wire loom total lock caster 1x 4x Contents Box 2 CEPCART1 or 2 4x amp pre assembly of 1x Upper frame Lift handle 1x Additional Tools Required Rubber mallet A Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 74 Epson Mobile Cart Base Frame Before beginning you should have Hardware Boxi Ce LL GD Mx lt sea nse M6 x 30mm bolt 1x
17. or 2 cccccccccceccceecseeceeeeessueeseeteeesaees 10 Assemble the Optional Rear Laptop Arm CEPCARTA ccccccccccceeeeeeeeeeeees 19 Assemble the Optional Keyboard Tray CEPCART4 cccccccccecceeeneeeeeeeeeees 25 Assemble the Optional Side Laptop Arm CEPCART 9 cccccccsceeeeseeeeeeeeees 21 28 44 We SEAMING SON BON eaen EAE E E EE ER 38 Assemble the Optional Lock Box CEPCART3 ccccccccccceecceeceeeeeeeeeeaeeeaeeeaes 40 Setting up the Projector for SC asec cn ores e ee ceecteteeunensnseacuanse venusenuatteeeeseteueesnseee 47 Routing Cables on the WW icecacceacgarocinaceusceseosechatatde veg sane dacenosecsananemaapecasuetoaietee 48 THOS TOL ISG E E EEEE E EEEE 49 50 Care amp Maintenance cccccscccececeeeceeeceeeceeeecucccueecenecseceeeseaeeceeecseesseeseeeseesas 51 Validate Your Warranty To validate your three year frame warranty submit the ON LINE form at www copernicused com Enter a drawing to win a Copernicus Product for your classroom at the same time Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Watch for These Helpful Symbols Tips for Assembly This symbol denotes a 2 or 3 Person Task For safety please ensure that there are the dd suggested number of people working on steps displaying this symbol reon ack Seek anal attention The symbol denotes a step needing extra attention to ensure it is done correctly E
18. ords into the side of the PP E E po e EPE E O projector VGA cord plugs into Computer 1 source At the back of the projector setting plate feed the two cables through the hole Hold the cables together and wrap the split black wire loom around the cables containing the length of them within the loom Following the diagram below route the loom appropriately Secure in multiple locations with Velcro straps Lift board to highest position before securing any Velcro straps Wiring through the 3 optional Lock Box es s 48 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Tips for Use of the Side Laptop Arm Folding the Arm Away Push in spring button to rotate tray down Routing Cables Along the Arm Sliding Mouse Tray Use the wire hooks on the arm to wrap extra cabling around keeping them neat amp tidy The mouse tray slides to the left or the right of the laptop tray ma E K al 2 al Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 49 x Tips for Use of the Rear Laptop Arm amp Keyboard Tray Folding the Tray Down Always fold the laptop tray down before moving the unit Keyboard Tray Use the tray on the front of the unit for a keyboard aa no need to walk to the back of the unit Ss Sliding Mouse Tray The mouse tray slides to the left or the right of the lap
19. row their intellects ANTHONY J D ANGELO ROBERT MAYNARD HUTCHINS Epson i E pson Mobile Cart for Epson ultra Short Throw Projectors Assembly Guide 470 475W 475W 480 4801 485W 485Wi Please note that in its unassembled state this product contains parts JN WARNING that can be hazardous to small children This product should be assembled by an adult Base Frame CEPCART1 or 2 Projector arm support 1 Upper frame pre assembly 1 Protective handle 2 Handle insert 4 Back support 2 Not Shown Short stretcher 2 Adapter Plate 1 Support stretcher grey 1 Board mounting frame top 1 Top clamp 2 Board mounting frame supports 2 Bottom cover 1 ii 3 St r e lt T Support stretcher with spring clips 1 Slide handle 1 Board mounting frame bottom 1 Lift handle 1 Center slide pole 1 Frame slide Base 1 1 t 4 swivel total e lock caster 4 Front cover 1 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Epson wi E pson Mobile Cart for Epson ultra Short Throw Projectors Assembly Guide 470 475W 475W 480 480 485W 485Wi Please note that in its unassembled state this product contains parts JN WARNING that can be hazardous to small children This product should be assembled by an adult Optional Lock Box CEPCART3 Lock box top 1 L
20. s 4x i 4x Secure Optional Lock Box Sides amp Top Secure on the inside Secure on the inside using hardware item using hardware item CAUTION J Maximum recommended weight in Sp lock box 50 Ibs 42 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc TTO a ANNI S 4x You will need not to scale w Lock box NS Lock box stretcher 1 x 1 Install Optional Lock Box Stretchers Image shown with door removed for clarity Ensure hole in stretcher is pointing upwards CAUTION Maximum recommended weight in lock box 50 Ibs Ensure that the cutout detail for the lock is oriented to the outside of the lock box Ensure the arrow is pointing down y Epson_CART Version 2012_A May 8 2012 Copemicus Educational Products Inc 43 29 You will need not to scale Laptop tray x 1 Install Optional Side Laptop Tray Slide laptop tray onto side laptop extension arm CAUTION Maximum recommended weight on side laptop tray 20 Ibs TIGHTEN ALL FASTENERS ON THE UNIT Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc 44 Install Release Cable WARNING Gas Cylinder is under pressure To avoid property damage or bodily injury please ensure unit is fully assembled before adjusting the height Hook the bottom of the cable into the
21. top tray Tip for Reducing Image Shaking Lock the FRONT casters and unlock the BACK casters to reduce the amount of image shaking 50 Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc Care amp Maintenance How to care for your Height Adjustable Mobile Cart The cart is made for indoor use only Cleaning wipe with dry or damp cloth and use mild soap only if necessary Verify that the gas lift is working properly the lift is in good condition if you can raise the board to maximum height using a small amount of your own force to assist it and lower it back down by applying a light pressure on the handle Please call Copernicus if your gas lift needs maintenance Perform bushing lubrication yearly See instructions below Lubricate Laptop Arm joints as needed See instructions below For care of the board and projector please refer to the manufacturer s instructions Bushing Lubrication Instructions 1 Lower the unit to its lowest position 2 Apply a generous bead of Petroleum Jelly all around the top of each bushing pressing some in the gap between the frame and bushing There are bushings on either side of the unit A and B and in the center C 3 Raise the board to its highest position 4 Repeat the application of Petroleum Jelly on the bottom of the slide guide that has two bushings B 5 Lower the unit back down to lowest position Apply Petroleum Jelly
22. ucts Inc 9 mmm LO OF QC washer 1x nut 1x mM M3 acorn nut 4x You will need not to kan 6 att Caster x 4 Gs Base x 1 Bottom cover x 1 5 DAQ Do not tighten any fasteners unless instructed This will help with the assembly of your unit 2 Person Task Install Casters amp Bottom Cover Lock casters first WARNING Be careful not to pinch your fingers when locking the casters To avoid property damage or bodily injury please ensure casters are locked before proceeding with assembly Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc AS WK O avec threaded M8 x 50mm bolt 2x 2x flat washer 2x You will need not to scale ee Leg x 2 CAUTION Maximum recommended weight on Attach Legs to Base bottom shelf 50 Ibs i i Ensure legs are aligned the correct way when looking from the front or back of the unit Hole indents should always be to the outside of the unit t l Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc l Actual Size 3 SM ANN 5 You will need not to scale Support stretcher grey x 1 Install Support Stretcher Epson_CART Version 2012_A May 8 2012 Copernicus Educational Products Inc You will need not to scale Slide handle x 1 Slide frame x 1 2 Person Task Install Slide Frame amp Slide Handl
Download Pdf Manuals
Related Search