Enterasys Networks SecureStack C2RPS-CHAS2 User's Manual
Contents
1. SOODLA ABE 1 C2RPS CHAS2 chassis with one PSM 3 Mounting screws supplied by user 2 Rails of 19 inch rack SecureStack C2 Installation Guide 2 5 Connecting the PSM Cables and AC Power Cords Connecting the PSM Cables and AC Power Cords The PSMs are connected to the SecureStack C2 Ethernet switch devices using C2RPS PSM Cables 2 6 Installation To connect the PSMs proceed as follows 1 4 Connect one end of the C2RPS PSM Cable shown in Figure 2 3 to the Redundant Power Supply connector on the switch device Then connect the other end to the Redundant Power Supply connector at the rear of the PSM as shown in Figure 2 4 and Figure 2 5 Connect a standard AC power cord to the AC input power connector on the PSM shown in Figure 2 4 then plug the AC power cord into the main AC power outlet The green Power LED on the front of the PSM will illuminate to indicate a successful connection If the LED remains off proceed as follows a Check the AC power cord connection at the AC power source and make sure the power source is within specification b Check the AC power connection to the PSM c Swap the AC power cord with a known good one d Ifthe green LED continues to remain off contact Enterasys Networks Refer to Getting Help on page 1 5 for instructions Otherwise proceed to step 4 If installing two PSM power supplies repeat steps 1 through 3 for the second PSM Figure 2 3 C2R2. front view with two PSMs mmmrma 1 2 1 3 SecureStack C2RPS CHAS2 rear view with two PSM8 mtmerrma 1 2 1 4 C2RPS PSM front VISA AAA o i a t 1 3 1 5 CZRPS PSM Fear VIEW circa 1 3 1 6 RPS Supporting Two SecureStack Switches nnnnanannnenenanneeneatanannannanneaa 1 4 2 1 CCP Sok ale ML ciis Meer 2 3 2 2 Fastening the C2RPS CHAS2 to the Rack rr rr naa 2 5 2 3 ducis a EARS em a 2 6 2 4 Power Connectors on C2RPS PSM rear view esee innen naaman avaamaan kad 2 6 2 5 C2RPS PSM Cable and AC Power Cord Connections esses 2 7 A 1 C2RPS PSM Redundant Power Supply Connector Pin Locations 4 A 2 Tables 2 4 2 2 A 1 A 2 A 3 A 4 contents ot DZ2RPSECHASZ LIO ii ingi AAA 2 2 Contents er G2RPS PEN Cal sica sra echo PER EEE T ren ERE A ande ae A 1 CARP Ss Pohl SDSOITICOIIONS aan ON E TNT a A 2 C2RPS PSM Redundant Power Supply Connector Pin Functions Compliance Standards ss peesaa TT A 3 About This Guide This guide provides an overview installation and troubleshooting instructions and specifications for the Enterasys Networks SecureStack C2 redundant power supply chassis C2RPS CHAS2 power supply module C2RPS PSM DC power cables C2RPS PSM Cable and AC power cords Note In this document the following terms are used RPS refers to a complete redundant power system which includes
3. BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THIS FOREGOING LIMITATION SHALL APPLY REGARDLESS OF THE CAUSE OF ACTION UNDER WHICH DAMAGES ARE SOUGHT THE CUMULATIVE LIABILITY OF ENTERASYS TO YOU FOR ALL CLAIMS RELATING TO THE PROGRAM IN CONTRACT TORT OR OTHERWISE SHALL NOT EXCEED THE TOTAL AMOUNT OF FEES PAID TO ENTERASYS BY YOU FOR THE RIGHTS GRANTED HEREIN vi 8 AUDIT RIGHTS You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and accordingly You hereby agree to maintain complete books records and accounts showing i license fees due and paid and ii the use copying and deployment of the Program You also grant to Enterasys and its authorized representatives upon reasonable notice the right to audit and examine during Your normal business hours Your books records accounts and hardware devices upon which the Program may be deployed to verify compliance with this Agreement including the verification of the license fees due and paid Enterasys and the use copying and deployment of the Program Enterasys right of examination shall be exercised reasonably in good faith and in a manner calculated to not unreasonably interfere with Your busi
4. Figure 1 5 C2RPS PSM rear view 1 Redundant Power Supply connector 2 AC input connector 12 Vdc inputs and PSM status outputs SecureStack C2 Installation Guide 1 3 RPS Deployment Strategies RPS Deployment Strategies 1 4 Introduction The RPS can be deployed ina variety of situations with mission critical applications For example e For use in a voice and data network where switches are connected to IP phones and PCs Connecting an RPS to the switches can prevent voice network failures caused by switch power failures e For use in traditional data 10 100 1000 Ethernet switches carrying mission critical data Figure 1 6 shows an example of the RPS providing redundant power backup for two SecureStack C2 switches If a SecureStack C2 switch device experiences an internal power supply failure the following occurs 1 The internal DC power source of the switch device is immediately switched over from the internal DC power supply to the RPS DC power input 2 The switch device saves this status information for future retrieval if necessary Figure 1 6 RPS Supporting Two SecureStack Switches C2RPS PSM C2RPS PSM m e e 1 C2RPS CHAS2 chassis front view with two PSMs 3 SecureStack C2 Ethernet switches 2 C2RPS PSM Cables for 12 Vdc and status information from PSMs Note The C2RPS PSMs used in C2RPS CHAS2 are interchangeable with those used in the C2RPS CHASS chassis available from Enterasys Netwo
5. INCLUDES AMONG OTHER PROVISIONS THE LICENSE THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO THIS AGREEMENT ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT ENTERASYS NETWORKS LEGAL DEPARTMENT AT 978 684 1000 You and Enterasys agree as follows 1 LICENSE You have the non exclusive and non transferable right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this Agreement 2 RESTRICTIONS Except as otherwise authorized in writing by Enterasys You may not nor may You permit any third party to i Reverse engineer decompile disassemble or modify the Program in whole or in part including for reasons of error correction or interoperability except to the extent expressly permitted by applicable law and to the extent the parties shall not be permitted by that applicable law such rights are expressly excluded Information necessary to achieve interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasys applicable fee ii Incorporate the Program in whole or in part in any other product or create derivative works based on the
6. Program in whole or in part iii Publish disclose copy reproduce or transmit the Program in whole or in part iv Assign sell license sublicense rent lease encumber by way of security interest pledge or otherwise transfer the Program in whole or in part v Remove any copyright trademark proprietary rights disclaimer or warning notice included on or embedded in any part of the Program 3 APPLICABLE LAW This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts None of the 1980 United Nations Convention on Contracts for the International Sale of Goods the United Nations Convention on the Limitation Period in the International Sale of Goods and the Uniform Computer Information Transactions Act shall apply to this Agreement 4 EXPORTRESTRICTIONS You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the Program is obtained from the U S Government or an exception from obtaining such license may be relied upon by the exporting party If the Program is exported from the United States pursuant to the Li
7. a C2RPS CHAS2 chassis and optional power supply modules Chassis refers to the C2RPS CHAS2 chassis PSMrefers to the C2RPS PSM power supply module PSM cable refers to the C2RPS PSM Cable 12 Vdc power cable Who Should Use This Guide This guide is intended for a network administrator responsible for installing and setting up the stackable switch i Electrical Hazard Only qualified personnel should perform installation procedures Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und gualifiziertes Personal vorgenommen werden How to Use This Guide Read through this guide completely to familiarize yourself with its contents and gain an understanding of the features and capabilities of the RPS components A general working knowledge of data communications networks is helpful when setting up an RPS C2RPS CHAS2 chassis with optional power supply modules SecureStack C2 Installation Guide xi Related Documents This preface provides an overview of this guide and the SecureStack C2 manual set and a brief summary of each chapter and the conventions used throughout this guide To locate information in this guide refer to the following table For Refer to The features and capabilities of the C2RPS CHAS2 Chapter 1 Introduction chassis and optional power supply modules This chapter also
8. agreement Agreement between the end user You and Enterasys Networks Inc on behalf of itself and its Affiliates as hereinafter defined Enterasys that sets forth Your rights and obligations with respect to the Enterasys software program firmware installed on the Enterasys product including any accompanying documentation hardware or media Program in the package and prevails over any additional conflicting or inconsistent terms and conditions appearing on any purchase order or other document submitted by You Affiliate means any person partnership corporation limited liability company or other form of enterprise that directly or indirectly through one or more intermediaries controls or is controlled by or is under common control with the party specified This Agreement constitutes the entire understanding between the parties and supersedes all prior discussions representations understandings or agreements whether oral or in writing between the parties with respect to the subject matter of this Agreement The Program may be contained in firmware chips or other media BY INSTALLING OR OTHERWISE USING THE PROGRAM YOU REPRESENT THAT YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO ACT YOU AND YOUR SHALL BE DEEMED TO REFER TO SUCH ENTITY AND THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT WHICH
9. de radio en cuyo caso puede ser requerido tomar medidas adecuadas Klasse A ITE Anmerkung WARNHINWEIS Dieses Produkt z hlt zur Klasse A Industriebereich In Wohnbereichen kann es hierdurch zu Funkst rungen kommen daher sollten angemessene Vorkehrungen zum Schutz getroffen werden Product Safety This product complies with the following UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Seguridad del Producto El producto de Enterasys cumple con lo siguiente UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 Produktsicherheit Dieses Produkt entspricht den folgenden Richtlinien UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 Electromagnetic Compatibility EMC This product complies with the following 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 Compatibilidad Electrom gnetica EMC Este producto de Enterasys cumple con lo siguiente 47 CFR Partes 2 y 15 CSA C108 8 89 336 EEC EN 55022 EN 55024 EN 61000 3 2 EN 61000 3 3 AS NZS CISPR 22 VCCI V 3 Elektro magnetische Kompatibilit t EMC Dieses Produkt entspricht den folgenden Richtlinien 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment
10. for details Table 2 1 Contents of C2RPS CHAS2 Carton Item Quantity C2RPS CHAS2 1 This guide SecureStack C2 Installation Guide 9034091 xx 1 Release Notes 1 Table 2 2 Contents of C2RPS PSM Carton Item Quantity C2RPS PSM 150 Watt DC Power Supply Module 1 USA NEMA Power Cord 1 C2RPS PSM Cable 1 Notice Card 1 Installing C2RPS PSMs 2 2 Installation Caution Observe all Electrostatic Discharge ESD precautions when handling sensitive electronic equipment Precauci n Al trabajar con equipos electr nicos sensibles tome todas las precauciones de seguridad para evitar descargas de electricidad est tica When you receive your C2RPS CHAS2 chassis a coverplate will be in place over each power supply slot To install the PSMs refer to Figure 2 1 and proceed as follows 1 Place the chassis on a sturdy flat surface where you plan to install PSMs 2 Align the PSM with one of the slots then slide the PSM forward until its front panel is flush against the chassis front panel 3 Fasten the PSM to the chassis using the captive screws on the PSM front panel 4 Repeat steps 2 and 3 for each additional PSM Proceed to Installing C2RPS CHAS2 into the Rack on page 2 4 for the rack mount installation instructions Installing C2RPS PSMs Figure 2 1 C2RPS PSM Installation 1 C2RPS CHAS2 chassis 3 Chassis power supply slot 2 C2RPS PSM power supply module 4 Captive screws 2
11. is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions COMBS RULERS ERE EA EHI VCCI oi ICROSZSAATBSEECI TOHE KE CHATS CBR Gees XHOTOCEMHBVESF COBRAR AAA ART 7 KIEKENDTILVM N K I BSMI EMC Statement Taiwan This is a class A product In a domestic environment this product may cause radio interference in which case the user may be reguired to take adeguate measures SARA EST NENEm TAERA IEA WMR Beka CEEP T EHBERERR Hy 3 tes ut BS SN SE Declaration of Conformity Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Address Conformance to Directive s Product Standards Equipment Type Environment 89 336 EEC 73 23 EEC Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 USA Enterasys Networks Ltd Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England EC Directive 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 EC Directive 73 23 EEC EN 60950 Networking Equipment for use in a Commercial or Light Industrial Environment Enterasys Networks Inc declares that the eguipment packaged with this notice conforms to the above directives Enterasys Networks Inc Firmware License Agreement BEFORE OPENING ORUTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an
12. provides the instructions for obtaining help from Enterasys Networks if needed Instructions to install an RPS into a standard 19 inch Chapter 2 Installation rack This involves installing the C2RPS CHAS2 chassis one or two PSMs PSM interconnecting cables and AC power cords Specifications for the C2RPS CHAS2 chassis PSM Appendix A Specifications PSM cable Redundant Power Supply connector pinout descriptions and Compliance Standards Related Documents Other manuals have been developed for the SecureStack C2 non PoE switch devices that can be connected to the RPS for power redundancy Caution The RPS does not support PoE compliant C2 switches Do not try to connect the AN power cable from this RPS to any C2 switch with a P suffix in the model name such as C2xxxxx xxP Otherwise damage to the device may result Precauci n El RPS no es compatible con switches SecureStack C2 con POE No intente conectar el cable de corriente del RPS a ning n switch SecureStack C2 que tenga el sufijo P en el nombre del modelo tal como C2xxxxx xxP De lo contrario el dispositivo puede da arse The SecureStack C2 switch manuals explain how to install the switch device connect network cable segments to the SecureStack C2 switch device and configure the switch device using the command line interface commands described in the SecureStack C2 Configuraton Guide Note Connection of the RPS system does not require reconfi
13. C2 Installation Guide xiii Conventions Used in This Guide xiv About This Guide Introduction This chapter provides a functional overview of a Redundant Power System RPS For information about Refer to page RPS Overview 1 1 C2RPS CHAS2 Chassis 1 2 C2RPS PSM Power Supply Module 1 3 RPS Deployment Strategies 1 4 Getting Help 1 5 RPS Overview An RPS redundant power system consisting of a C2RPS CHAS2 chassis and C2RPS PSM power supplies is a simple and economical solution to provide backup power for one or two SecureStack C2 Ethernet switch devices one for each switch device When a C2RPS PSM is connected to a switch device it continuously monitors the internal power supply of the switch device If a power interruption is detected the C2RPS PSM is automatically triggered to provide power for the switch device preventing an interruption in network traffic The end result is a more reliable network infrastructure protecting the network from a single source of failure from a network device power supply Depending on your system requirements the C2RPS CHAS2 chassis can consist of the following components to provide redundant power for one or two switch devices One C2RPS CHAS2 chassis One or two C2RPS PSMs one per SecureStack switch device One or two AC power cords one per C2RPS PSM One or two C2RPS PSM Cables one per CZRPS PSM Note The chassis is shipped without a PSM The PSMs are order
14. INATION Enterasys may terminate this Agreement immediately upon Your breach of any of the terms and conditions of this Agreement Upon any such termination You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program vii viii Contents About This Guide Who Should Use TAS 21 k 21 ee xi How to Use THIS SOS ore oed aim SA xi Related DoOIIBlB een xii Conventions Used in TRIS GUJE anni A Sr e e xiii Chapter 1 Introduction PS O UE EN UT 1 1 LZRFSUHASZ P rr stop ia ai i n 1 2 CZRPS PSM Power Supply Module an nen 1 3 RES Deployment Strategies ces een 1 4 Chapter 2 Installation O EE M 2 1 Unpacking Chassis and Power Supply M duleis ua 2 1 Ml RRS SMS een 2 2 Rire EE cl doi ea auda 2 3 installing GZISES CHASZ inte ihe RABE Guia dade ada eO a FH Lc SR RERO RR 2 4 Guidelines for RackmoaniInstallalon iasamusaaammtiamosss E 2 4 Rack Mounino TS LAB Me 2 5 Connecting the PSM Cables and AC Power Cards nassen a MUN AREE HIA DEA kaa 2 6 Appendix A Specifications C2RPS CHAS2 Chassis SOCIOS eek A 1 GSRPST SM SpA cios pp etate oa e pee p FER oca A 2 C2RPS PSM Redundant Power Supply Output Connector sess A 2 Kaman SUNG e lt abe meee reer neyo rire rere ener aaa E A 3 Figures 1 1 SecureStack C2RPS CHAS2 front view without PSM wmmrmrs 1 2 1 2 SecureStack C2RPS CHAS2
15. ING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS DOCUMENT WEB SITE OR THE INFORMATION CONTAINED IN THEM EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF KNEW OF OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 O 2005 Enterasys Networks Inc All rights reserved Part Number 9034091 01 April 2005 ENTERASYS ENTERASYS NETWORKS ENTERASYS MATRIX LANVIEW MATRIX NETSIGHT WEBVIEW and any logos associated therewith are trademarks or registered trademarks of Enterasys Networks Inc in the United States and other countries All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies Documentation URL http www enterasys com support manuals Documentacion URL http www enterasys com support manuals Dokumentation http www enterasys com support manuals Regulatory Compliance Information Federal Communications Commission FCC Notice This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This eguipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provid
16. PS PSM Cable Figure 2 4 Power Connectors on C2RPS PSM rear view 1 Redundant Power Supply connector OOOOOOOO a BS Ph 00055000 5 BIB RR A Redundant Power Supply LLLLLLI 2 AC power connector rear of chassis Connecting the PSM Cables and AC Power Cords Figure 2 5 C2RPS PSM Cable and AC Power Cord Connections Redundant Power Supply 1 Switch device 4 Switch device Redundant Power Supply connector 2 PSM cable 5 AC power cord type varies depending on country 3 PSM Redundant Power Supply 6 AC power outlet with ground connection connector type varies depending on country 5 On certain switches an LED indicator will show that a redundant power supply is now in operation Note No change in switch device configuration is necessary for this installation This completes the installation SecureStack C2 Installation Guide 2 7 Connecting the PSM Cables and AC Power Cords 2 8 Installation Specifications This appendix includes specifications for the C2RPS CHAS2 C2RPS PSM 12 Vdc power supply output connector and provides the Compliance Standards For information about Refer to page C2RPS CHAS2 Chassis Specifications A 1 C2RPS PSM Specifications A 2 C2RPS PSM Redundant Power Supply Output Connector A 2 Compliance Standards A 3 Enterasys Networks reserves the right to change the specifications at any time without notice C2RPS CHAS2 Chassis Specificati
17. Replacing an Installed C2RPS PSM To replace a PSM installed in an operating system proceed as follows Caution Observe all Electrostatic Discharge ESD precautions when handling sensitive A electronic eguipment Precauci n Al trabajar con equipos electr nicos sensibles tome todas las precauciones de seguridad para evitar descargas de electricidad est tica 1 Unplug the AC power cord of the PSM from the AC power source first then from the rear of the PSM 2 Loosen the captive screws securing the PSM until it is released from the chassis front panel 3 Pull the PSM out and remove it from the chassis 4 Repeat steps 1 through 3 for each additional PSM you plan to remove SecureStack C2 Installation Guide 2 3 Installing C2RPS CHAS2 into the Rack Note If you plan to remove and not replace a C2RPS PSM immediately reinstall coverplates over any empty power supply slots to prevent EMI leakage from the chassis To install a PSM proceed as follows 1 Align the PSM with the slot then slide the PSM forward until its front panel is flush against the chassis front panel Fasten the PSM to the chassis using the captive screws Perform steps 1 and 2 for each PSM being replaced When completed proceed to Connecting the PSM Cables and AC Power Cords on page 2 6 Installing C2RPS CHAS2 into the Rack To install the chassis into a 19 inch 48 3 cm rack you need four user supplied screws to fasten the chass
18. SecureStack C2 Redundant Power Supply Chassis C2RPS CHAS2 Installation Guide 2 enterasys fi E Caution Do not use this product with SecureStack PoE devices Any SecureStack device with a P suffix in the model number C2xxxx xxP indicates a SecureStack PoE compliant device and is not compatible with this power system Precauci n EI RPS no es compatible con switches SecureStack C2 con PoE No intente conectar el cable de corriente del RPS a ningun switch SecureStack C2 que tenga el sufijo P en el nombre del modelo tal como C2xxxxx xxP De lo contrario el dispositivo puede da arse 9034091 01 Networks that Know Electrical Hazard Only gualified personnel should perform installation procedures Advertencia electrica Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und gualifiziertes Personal vorgenommen werden Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made The hardware firmware or software described in this document is subject to change without notice IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEOUENTIAL DAMAGES WHATSOEVER INCLUD
19. cense Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the technology if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant or any major component of a plant export to Country Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign produced direct product is subject to national security co
20. de 1 5 Getting Help 1 6 Introduction Installation 2 Electrical Hazard Only gualified personnel should perform installation procedures Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und gualifiziertes Personal vorgenommen werden This chapter provides instructions to install all the components of an RPS To correctly install an RPS follow the order of information listed below For information about Refer to page Reguired Tools 2 1 Unpacking Chassis and Power Supply Module s 2 1 Installing C2RPS PSMs 2 2 Installing C2RPS CHASZ into the Rack 2 4 Connecting the PSM Cables and AC Power Cords 2 6 Reguired Tools A flat blade screwdriver is required to install the C2RPS CHAS2 and C2RPS PSMs Unpacking Chassis and Power Supply Module s The C2RPS CHAS2 and each C2RPS PSM are shipped separately To unpack these devices proceed as follows 1 Open the box and remove the packing material protecting the devices 2 Verify the contents of each carton and compare the contents shipped with those listed in Table 2 1 and Table 2 2 SecureStack C2 Installation Guide 2 1 Installing C2RPS PSMs 3 Perform a visual inspection of the switch devices for any signs of physical damage Contact Enterasys Networks if there are any signs of damage Refer to Getting Help on page 1 5
21. e reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment uses generates and can radiate radio frequency energy and if not installed in accordance with the operator s manual may cause harmful interference to radio communications Operation of this eguipment in a residential area is likely to cause interference in which case the user will be reguired to correct the interference at his own expense WARNING Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the eguipment Industry Canada Notice This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set outin the Radio Interference Regulations of the Canadian Department of Communications Le present appareil num rique n met pas de bruits radiodlectrigues d passant les limites applicables aux appareils num riques de la class A prescrites dans le Reglement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Class A ITE Notice WARNING Thisis a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Clase A Aviso de ITE ADVERTENCIA Este es un producto de Clase A En un ambiente dom stico este producto puede causar interferencia
22. ed separately Each PSM is shipped with an interconnecting C2RPS PSM Cable and an AC power cord SecureStack C2 Installation Guide 1 1 C2RPS CHAS2 Chassis 1 2 C2RPS CHAS2 Chassis Introduction The chassis is a two slot frame without AC power connections or electronics The chassis can be installed in a standard 19 inch rack and populated with one or two PSMs Each PSM operates independently Figure 1 1 shows the front view of the chassis without PSMs Figure 1 2 and Figure 1 3 show the front and rear views of a fully populated chassis Figure 1 1 SecureStack C2RPS CHAS2 front view without PSM gt enterasys Kos Figure 1 2 SecureStack C2RPS CHASZ2 front view with two PSMs C2RPS PSM x Gao Em o amaa zamma 7 popom EJCICIEISI m wj n OAO Sue SEE P C2RPS PSM x e is 220 m 7 MAGAD zamam o jm um m o 5 popom KOE ORO E EE Bae Figure 1 3 SecureStack C2RPS CHAS2 rear view with two PSMs C2RPS PSM Power Supply Module C2RPS PSM Power Supply Module The C2RPS PSM provides the following e Hot swap capability e One 12 Vdc 150 Watts of maximum continuous power output to a connected SecureStack C2 switch device e Front panel Status LED that indicates if the PSM is operating correctly Figures 1 4 and 1 5 show the front and rear view of the C2RPS PSM Figure 1 4 C2RPS PSM front view C2RPS PSM 1 Intake cooling fans 3 Captive screws 2 2 AC power LED
23. guration of the connected Ethernet Switch Each manual is written for qualified personnel responsible for installing the switch device and also have a general working knowledge of data communications networks and their physical layer components xii About This Guide Conventions Used in This Guide Conventions Used in This Guide The following conventions are used in this guide Note Calls the reader s attention to any item of information that may be of special importance Caution Contains information essential to avoid damage to the equipment Precauti n Contiene informaci n esencial para prevenir da ar el equipo Achtung Verwei t auf wichtige Informationen zum Schutz gegen Besch digungen Electrical Hazard Warns against an action that could result in personal injury or death AN due to an electrical hazard Riesgo Electrico Advierte contra una acci n que pudiera resultar en lesi n corporal o la muerte debido a un riesgo el ctrico Elektrischer Gefahrenhinweis Warnung vor s mtlichen Handlungen die zu Verletzung von Personen oder Todesf llen hervorgerufen durch elektrische Spannung f hren k nnen 1 Warning Warns against an action that could result in personal injury or death Advertencia Advierte contra una acci n que pudiera resultar en lesi n corporal o la muerte Warnhinweis Warnung vor Handlungen die zu Verletzung von Personen oder gar Todesf llen f hren k nnen SecureStack
24. is to the rack rails After installing the PSM s as described back in Installing C2RPS PSMs on page 2 2 rack mount the chassis as follows 2 4 1 Refer to the installation guidelines Guidelines for Rackmount Installation on page 2 4 Install the chassis into the rack Rack Mounting the Chassis on page 2 5 Connect the PSM cables and AC power cords Connecting the PSM Cables and AC Power Cords on page 2 6 Guidelines for Rackmount Installation The installation site must be within reach of the network cabling and meet the requirements listed below Installation Chassis placement close enough to connect the 2 meter 6 6 foot AC power cords from the PSMs to the AC power source Up to two three pronged power receptacles capable of delivering the current and voltage specified in C2RPS PSM Specifications on page A 2 Up to two AC outlets on independently fused circuits must be within 182 centimeters 6 feet from the installation site If there is an AC power source failure this will prevent the powering down of PSMs due to a single source power failure Power cords and type of outlet are dependent on the country In the United States one power cord with an NEMA 5 15P plug is provided with each C2RPS PSM An ambient temperature of between 5 C 41 F and 40 C 104 F must be maintained at the installation site with fluctuations of less than 10 C 18 F per hour Installing C2RPS CHAS2 in
25. license this Agreement or any of Your rights or obligations under this Agreement except that You may assign this Agreement to any person or entity which acquires substantially all of Your stock or assets Enterasys may assign this Agreement in its sole discretion This Agreement shall be binding upon and inure to the benefit of the parties their legal representatives permitted transferees successors and assigns as permitted by this Agreement Any attempted assignment transfer or sublicense in violation of the terms of this Agreement shall be void and a breach of this Agreement 12 WAIVER A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition Enterasys failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion 13 SEVERABILITY In the event any provision of this Agreement is found to be invalid illegal or unenforceable the validity legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby and that provision shall be reformed construed and enforced to the maximum extent permissible Any such invalidity illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction 14 TERM
26. ness In the event such audit discovers non compliance with this Agreement including copies of the Program made used or deployed in breach of this Agreement You shall promptly pay to Enterasys the appropriate license fees Enterasys reserves the right to be exercised in its sole discretion and without prior notice to terminate this license effective immediately for failure to comply with this Agreement Upon any such termination You shallimmediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program 9 OWNERSHIP This is a license agreement and not an agreement for sale You acknowledge and agree that the Program constitutes trade secrets and or copyrighted material of Enterasys and or its suppliers You agree to implement reasonable security measures to protect such trade secrets and copyrighted material AI right title and interest in and to the Program shall remain with Enterasys and or its suppliers All rights not specifically granted to You shall be reserved to Enterasys 10 ENFORCEMENT You acknowledge and agree that any breach of Sections 2 4 or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys rights under this Agreement in addition to any and all remedies available at law 11 ASSIGNMENT You may not assign transfer or sub
27. ntrols as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Program i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Enterasys and or its suppliers For Department of Defense units the Program is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 DISCLAIMER OF WARRANTY EXCEPT FOR THOSE WARRANTIES EXPRESSLY PROVIDED TO YOU IN WRITING BY Enterasys Enterasys DISCLAIMS ALL WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTORY QUALITY FITNESS FOR A PARTICULAR PURPOSE TITLE AND NON INFRINGEMENT WITH RESPECT TO THE PROGRAM IF IMPLIED WARRANTIES MAY NOT BEDISCLAIMED BY APPLICABLE LAW THEN ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THIRTY 30 DAYS AFTER DELIVERY OF THE PROGRAM TO YOU 7 LIMITATION OF LIABILITY IN NO EVENT SHALL ENTERASYS OR IIS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF
28. ons Table A 1 provides the physical specifications for the CZRPS CHAS2 Table A 1 C2RPS CHAS2 Specifications Item Specification Power supply slots Two slots for optional C2RPS PSMs Dimensions without mounting brackets 5 5 H x 48 2 W x 18 0D cm 2 2 H x 19 0 W x 7 0 D in Net Weight Unit Only 0 95 kg 2 09 Ib Gross Weight Packaged Unit 1 60 kg 3 52 Ib SecureStack C2 Installation Guide A 1 C2RPS PSM Specifications C2RPS PSM Specifications Refer to Table A 2 for the input output port specifications Table A 2 C2RPS PSM Specifications Item Specification Electrical AC Input Freguency Range 47 63 Hz AC Input Voltage Range 85 264 Vac Output Voltage 12 Vdc Output Current 1 0 A min 8 5 A or 13 0 A max Maximum Output Power 102 W or 156 W continuous Physical Dimensions 19 6 H x 5 2 W x 25 7 D cm 7 7 H x 2 04 W x 10 1 D in Net Weight Unit Only 1 75 kg 3 85 Ib Gross Weight Packaged Unit 3 20 kg 7 04 Ib MTBF 300 000 Hours C2RPS PSM Redundant Power Supply Output Connector A 2 Specifications For pin location and function refer to Figure A 1 and Table A 3 respectively Note The following information is for troubleshooting purposes only For proper operation do not use any other cable except the C2RPS PSM Cable This cable is specially designed for this application and meets all necessary regulatory and safety standards The use of non approved cables will void you
29. r warranty Figure A 1 C2RPS PSM Redundant Power Supply Connector Pin Locations Compliance Standards Table A 3 C2RPS PSM Redundant Power Supply Connector Pin Functions Pin Number Function 1 Ground 2 No connection 3 12 Vdc Output 4 12 Vdc Output 5 12 Vdc Output 6 12 Vdc Output 7 Ground 8 Ground 9 No connection 10 No connection 11 Status 1 12 Status 2 13 Power good 14 Ground Compliance Standards The C2RPS PSM meets the safety and electromagnetic compatibility EMC requirements listed in Table A 4 Table A 4 Compliance Standards Item Standard Safety UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 and IEC 60950 Electromagnetic Compatibility EMC Applies to RPS system with two modules installed and working with two network devices 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 and VCCI V 3 SecureStack C2 Installation Guide A 3 Compliance Standards A 4 Specifications
30. rks Getting Help Getting Help For additional support related to the C2RPS CHAS2 or this document contact Enterasys Networks using one of the following methods World Wide Web http www enterasys com support Phone 603 332 9400 1 800 872 8440 toll free in U S and Canada For the Enterasys Networks Support toll free number in your country http www enterasys com support gtac all html Internet mail support enterasys com To expedite your message please type C SERIES in the subject line To send comments or suggestions concerning this document to the Technical Publications Department techpubs enterasys com To expedite your message please include the document Part Number in the email message Before contacting Enterasys Networks for technical support have the following information ready Your Enterasys Networks service contract number A description of the failure A description of any action s already taken to resolve the problem e g changing mode switches rebooting the unit etc The serial and revision numbers of all involved Enterasys Networks products in the network A description of your network environment layout cable type etc Network load and frame size at the time of trouble if known The device history i e have you returned the device before is this a recurring problem etc Any previous Return Material Authorization RMA numbers SecureStack C2 Installation Gui
31. to the Rack Caution To ensure proper ventilation and prevent overheating leave a minimum clearance space of 10 16 cm 4 0 in at the front and rear of the N POE Chassis Precauci n Para asegurar una buena ventilaci n y evitar que el sistema se sobrecaliente deje un espacio m nimo de 10 16 cm 4 pulgadas con respecto a la parte delantera y trasera del chasis N POE device s without compromising the stability of the rack Otherwise personal injury and or 1 Warning Before installing the chassis into a rack ensure that the rack can support the equipment damage may result Advertencia Antes de instalar el chassis en un rack asegurarse que el rack puede soportar el los dispositivo s sin comprometer la estabilidad del mismo De otra forma puede suceder algun tipo de da o personal o del equipo Warnhinweis Sch tzen Sie sich vor Verletzungen und Ger teschaden berzeugen Sie Sich vor der Installation des Chassis in das Rack von dessen Stabilit t Rack Mounting the Chassis Refer to Figure 2 2 and proceed as follows to install the chassis into a 19 inch 48 3 cm rack 1 Position the chassis between the vertical frame members and align the mounting holes in the chassis brackets with those in the rack frame 2 Fasten the chassis securely to the frame using four mounting screws user supplied Figure 2 2 Fastening the C2RPS CHAS2 to the Rack oon addon mm m m Nasen E g i am o
Download Pdf Manuals
Related Search