Emerson S4K2UC User's Manual
Contents
1. USER MANUAL 6 5 0 Technical Support 5 1 Contact Information To contact SolaHD technical support please use one of the following methods Phone 1 800 377 4384 US or 1 847 268 6651 International E mail solahd technicalservices emerson com Web site www solahd com INTELLISLOT RELAY CARD USER MANUAL 7 SolaHD 1 800 377 4384 US 1 847 268 6651 International www solahd com EMERSON Industrial Automation P N A272 240 Rev 0 May 20112. IntelliSlot Relay Card User Manual IS RELAY L3 4 SOLAD Contents 1 0 Introduction 3 1 1 Inspecting ShipmentonReceipt s emuta a N aca koad aih a e wok e a a ae os sons 3 2 0 Installation 4 2 1 Required Partsstlools se p a Go Ge as Gey ahd Bye Bh ee Ro ee Alte a oh Gl os Se ae we bee ea G 4 22 Installation Instructions lt a usc ox modo mo RU RR n l c i mode BC NAY wR OR ADU A ER dene LR 4 3 0 PIN Configuration 5 Table 1 IntelliSlot Relay Card PIN Configuration llo 5 4 0 Jumper Setup 6 Table 2 JumperConnectlons uc a Bee EM Roe OR RO 3 9 ORE 4 9 ROS d 3E Row 4 RUN 6 5 0 Technical Support 7 5 1 Contactiinformations uox x x 65 gi x g Sai ADS E RR ETUR u dc Ale SED gu y A ae Q24 s42 ae ee A 7 While every precaution has been taken to ensure accuracy and completeness in this manual EGS Electrical Group LLC assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions The SolaHD and Emerson logos are registered in the U S Patent and Trademark Office All other product or service names are the property of their registered owners 2011 EGS Electrical Group LLC All rights reserved Specifications are subject to change without notice 1 0 Introduction The IntelliSlot relay card IS RELAY provides contact closure for remote monitoring of alarm conditions in your SolaHD UPS The IntelliSlot relay card is
3. e SolaHD units listed in Section 1 0 Introduction Table 1 IntelliSlot Relay Card PIN Configuration Common Low Battery Low Battery Low Battery Common UPS Fault UPS Fault UPS Fault Common On Battery On Battery On Battery Signal Ground Signal Ground UPS Any Mode Shutdown Summary Alarm Summary Alarm Common Summary Alarm On UPS On Bypass Common On Bypass Closed if Low Battery point occurs Closed if battery is OK Closed if UPS Fault occurs Closed if no UPS failure AN Closed if ON UPS inverter power Closed if On Bvpass INTELLISLOT RELAV CARD USER MANUAL 5 4 0 Jumper Setup The IntelliSlot relay card has five jumpers P3 through P7 as shown in Figure 2 Each jumper connects two PINs Front of card Jumper P6 Jumper P5 Jumper P4 Jumper P3 wi n _ n Tie Jumper P7 Figure 3 Jumper location amp numbering By default all five jumpers have shunts installed The two PINs are shunted together to provide the functions shown in Table 2 allowing relay commons to be tied together NOTE The jumpers should be removed if there are any external voltage sources that may intentionally or inadvertently be connected to the relay Removing the shunt from any two PINs breaks the connection between the relay commons so they are not tied together Table 2 Jumper Connections Rae we OOO INTELLISLOT RELAY CARD
4. easy to install and integrates with other relay contact monitoring systems This advanced power management device is designed to function in units with a IntelliSlot port such as SAKC Series S5K Series Please visit our Web site at www solahd com for the current list of supported products On supported units the inverter shut off command can be controlled from the computer directly connected to the UPS via the factory installed DB9 connector and will conserve battery power after the workstation shutdown is complete The IntelliSlot relay card is rated for 24 V ac V dc at 1 A 1 1 Inspecting Shipment on Receipt Upon accepting shipment inspect the packaging and product for any damaged or missing parts If any damage is observed report it to the shipping company and your local SolaHD representative immediately If any components are missing contact your local SolaHD representative for replacement Items included with the shipment are IntelliSlot relay card protected by an anti static bag User manual INTELLISLOT RELAY CARD USER MANUAL 3 2 0 Installation 2 1 Required Parts amp Tools NOTE Make sure you have the following parts and tools before you begin the installation IntelliSlot relay card provided 2 medium Phillips or small flathead screwdriver 2 2 Installation Instructions 1 Turning off the UPS prior to installation is suggested although not required 2 Locate the IntelliSlot port See exampl
5. es in Figure 1 Refer to the UPS user manual for port location and orientation 3 Remove the two retaining screws from the IntelliSlot port cover plate see Figure 1 Save the screws for reassembly in Step 5 4 Insert the IntelliSlot relay card Make sure the holes are aligned with those on the UPS Initially the card should slide in freely as you carefully align the screw holes As you feel it click into place press firmly to ensure solid seating in the slot 5 Usethe screwdriver to secure the IntelliSlot relay card to the UPS chassis with the two retaining screws removed in Step 3 Make sure the screws are snug not tight to avoid damage to the device nn np pp oo MM PRESS TORESET l 20A 125V IntelliSlot Relay Card Remove screws Figure 1 Installation 6 Use these guidelines for terminal block specifications Acceptable wire size 24 16 AWG Wire strip length 0 24 0 28 in 6 7 mm Please proceed to Sections 3 0 Pin Configuration and 4 0 Jumper Setup to configure the terminal blocks and jumpers INTELLISLOT RELAY CARD USERMANUAL 4 3 0 PIN Configuration The IntelliSolt relay card has two terminals blocks TB1 green numbered 1 9 and TB2 black numbered 10 18 as shown in Figure 2 TB1 green IS RELAY TB2 black 18 Figure 2 PIN location amp numbering Please refer to the UPS User manual for the UPS terminal block configuration The PIN functions in Table 1 apply only to th
Download Pdf Manuals
Related Search