Emerson LK180 Owner's Manual
Contents
1. Installation on Emerson Fans Having Two Piece Die Cast Switch Housings 1 Remove all parts and parts packages from carton 2 Remove the cover from switch housing below ceiling fan Figure 5 3 Carefully pull down white and blue wires from the switch housing and remove wire connectors 4 Thread the white and black wires of the light fitter through the cover lockwasher hex nut and then secure by using a wrench 5 Connect the white wire from the ceiling fan to the white wire of the light fitter Connect the blue wire from the ceiling fan to the black wire of the light fitter Use listed wire connectors previously removed in Step 3 to make connections Figures 5 and 6 FAN SWITCH SWITCH _ HOUSING WHITE WIRE BLUE WIRE WIRE CONNECTORS WHITE WIRE mea HEX NUT a j LOCKWASHER amp a sWe LIGHT FITTER FILTER FLANGE RUBBER WASHER FAN SWITCH PEX NUT FINIAL FN200 BOWL CAP FN200 Figure 5 WARNING To avoid possible fire or electrical shock make certain no bare wire strands are exposed outside wire connectors Figure 6 4 WARNING To avoid possible fire or electrical shock be careful not to pinch wires between the switch housing and the light fitter NOTE The FN200 finial pack comes with three options no holes one hole and two holes for pull chain options 6 Depending on the model purchased insert the fan speed control switch chain through the offset hole in the gla2. FINIAL FN20C BOWL CAP FN200 Figure 2 WARNING To avoid possible fire or electrical shock make certain no bare wire strands are exposed outside wire connectors Figure 3 4 WARNING To avoid possible fire or electric shock be careful not to pinch wires between switch cup and the cover plate ETL Model No LK180 NOTE The FN200 finial pack comes with three options no holes one hole and two holes for pull chain options 12 Depending on the fan model insert the fan speed control switch chain through the offset hole in the glass bowl and the hole in the bowl cap 13 Gently place the glass bowl onto the light fixture Figure 4 Secure the glass by installing the rubber washer and thin hex nut finger tight Then place the bowl cap onto the threaded light fixture route the fan speed control chain through the outer hole and the light fitter control chain through the center hole Install and tighten the finial nut onto the threaded light fixture Figure 2 RUBBER WASHER FAN SPEED CONTROL CHAIN HEX NUT BOWL CAP FINIAL NUT LIGHT FITTER CONTROL CHAIN COUPLING 2 WOOD PENDANT 2 Figure 4 14 Connect the wood pendant supplied to the switch pull chain by sliding the wood pendant small hole first onto the pull chain Attach the chain coupling to the end of the chain and allow the wood pendant to fall down over the coupling NOTE It is advisable to periodically check the tight ness of the finial
3. READ AND SAVE THESE INSTRUCTIONS EMERSON Ceiling Fan Light Fixture Model Number Owner s Manual LK180 Net weight 4 5 Lbs QI pour 13 wat CFL Metium Base Bubs Questions problems missing parts Before returning to the store call Emerson Electric Customer Service 8 a m 6 p m Eastern Monday Friday 1 800 654 3545 www emersonfans com Safety Instructions WARNING To avoid fire shock and serious personal injury follow all instructions carefully 1 Read your Owner s Manual carefully before installing the light fixture Retain Owner s Manual for future reference 2 Be careful of the fan and blades when cleaning painting or working near the fan Before installing or servicing the light fixture or ceiling fan switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 3 Do not exceed the wattage indicated on fixture ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION 1 To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring 2 Make certain no bare wires are exposed outside the wire connectors 3 All wiring must conform to national and local electrical codes 4 Follow the recommended instructions for the proper method of wiring your new light fix
4. Relates To The Warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state S EMERSON Air Comfort Products Form No BP7486 DIVISION OF EMERSON ELECTRIC CO Printed in China 11 13 Part No F40BP74860000 ee cree 8100 W Florissant St Louis MO 63136 ETL Model No LK180
5. hrough the center hole in the switch cup Figure 2 and thread the switch cup onto the light fitter Hold wires taut while installing switch cup to prevent the wires from twisting Tighten the fitter until the fan switch chain aligns with the hole in the fitter MOTOR CONNECTOR SWITCH CUP SCREWS p CONNECTOR SWITCH CUP CENTER SCREW Figure 1 EMERSON Insert the black and white wires through the lock washer and hex nut supplied firmly tighten the hex nut to secure the light kit fitter to the switch cup Connect the white wire from the switch cup to the white wire of the light fitter Figure 2 Connect the blue wire from the switch cup to the black wire of the light fitter Use listed wire connectors previously removed in Step 5 to make connections Figures 2 and 3 8 Carefully tuck all wires and splices into the switch cup Figure 2 9 Connect the motor connector to the switch cup connector 10 Position the cup light fitter in the cover plate and install the three screws that were previously removed in Step 2 and tighten securely 11 The light sockets are equipped to take four 13 watt CFL medium base bulbs MOTOR SWITCH CUP CONNECTOR J eS BLACK WIRE WIRE CONNECTOR WHITE WIRES LOCKWASHEF FAN SWITCH CHAIN SS BLUE WIRE 7 HEX NUT SCREWS SWITCH CUP LIGHT FITTER FILTER FLANGE RUBBER WASHER FAN SWITCH paia a CHAIN
6. ny such damage What Is Not Covered This warranty also does not cover any defects malfunctions or failures caused by e Repairs by persons not authorized by Emerson Electric Co e Use of parts or accessories not authorized by Emerson Electric Co e Mishandling improper installation modifications or damage to your light fixture while in your possession or e Unreasonable use misuse abuse including failing to do reasonable and necessary maintenance and normal wear and tear Additionally this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when e The original purchaser or user ceases to own the product or e The ceiling fan is moved from its original point of installation This warranty is only valid within the 50 states of the United States and the District of Columbia No other written or oral warranties apply and no employee agent dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co REPAIR REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES Incidental damages include but are not limited to such damages as loss of time and loss of use Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly How State Law
7. rranty for one year from the date you purchased your light fixture ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR What Will Emerson Electric Co Do To Correct Problems Emerson Electric Co will replace a defective Emerson Light Fixture at no charge to you WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL REINSTALLATION AND SHIP PING OF THE PRODUCT TO EMERSON ELECTRIC CO How Can You Get Service YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE You can return the product to our factory or to your nearest authorized service center e To return the product to the factory obtain a return authorization and service identification tag by writing to Air Comfort Products Division of Emerson Electric Co 8100 W Florissant Ave St Louis MO 63136 Include all model numbers shown on the product with your request e To return the product to an authorized service center call 1 800 654 3545 for the address of the nearest authorize service center You will be responsible for all insurance freight or other transportation charges to our factory or authorized service center Your Emerson Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for a
8. ss bowl and the hole in the bowl cap 7 Carefully tuck all wires and splices into the switch housing 8 Install the cover and fitter assembly to the switch housing by using the screws removed in Step 2 9 Gently place the glass bowl onto the light fixture Figure 7 Secure the glass by installing the rubber washer and thin hex nut finger tight Then place the bowl cap onto the threaded light fixture route the fan speed control chain through the outer hole and the light fitter control chain through the center hole Install and tighten the finial nut onto the threaded light fixture Figure 5 emersonfans com Please contact 1 800 654 3545 for further assistance ETL Model No LK180 10 The light sockets are equipped to take four 13 watt CFL medium base bulbs 11 Connect the wood pendant supplied to the switch pull chain by sliding the wood pendant small hole first onto the pull chain Attach the chain coupling to the end of the chain and allow GLASS the wood pendant to fall down over the coupling RUBBER WASHER D FAN SPEED CONTROL CHAIN FINIAL NUT COUPLING 2 Figure 7 LIGHT FITTER CONTROL CHAIN WOOD PENDANT 2 LIMITED WARRANTY What The Warranty Covers All products covered by this Owner s Manual are warranted against all defects in workmanship and materials You must be the original purchaser or user of the product to be covered What The Period Of Coverage Is All components are covered by this wa
9. ture If you feel you do not have enough electrical wiring knowledge or experience have your light fixture installed by a licensed electrician Any electrical work not described in this manual should be performed by a licensed electrician WARNING To reduce the risk of possible fire and electrical shock install only on Emerson CF Series Ceiling Fans in indoor locations This light kit is not to be used on Emerson CF Series Ceiling Fans installed in damp or wet locations Part No F40BP74860000 Form No BP7486 Revision 131112 ETL Model Nos LK180 Assembly and Installation A WARNING Do not install or use the light fixture if any part is missing or damaged Contact your dealer for replacement 4 WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring Installation on Emerson Fans Having a Modular Switch Cup with Center Screw 1 Remove all parts and parts packages from the carton 2 Remove the switch cup from the cover plate by removing the three screws around the side of the switch cup Figure 1 3 Disconnect the motor connector from the switch cup connector Figure 1 4 Remove the center screw from the switch cup Figure 1 5 Carefully locate the white and blue wires labeled either L or LIGHT in the switch cup and remove the wire connectors from the wires 6 Insert the black and white wires from the light fitter t
Download Pdf Manuals
Related Search