Emerson LK141 Owner's Manual
Contents
1. 5 Carefully locate the white and blue wires labeled either L or LIGHT in the switch housing and remove the wire connectors 3 from the wires 6 Connect the white neutral wire from the switch cup to the white neutral wire of the light fixture Figure 4 Connect the blue line hot wire from the switch cup to the black line hot wire of the light fixture Use listed wire connections previously removed in step 5 to make connections Figures 4 and 5 The neutral and line hot wires must be installed as instructed to maintain proper polarly at the lampholders gt A To avoid possible fire or electrical shock make certain no bare wire strands are exposed outside wire connectors Figure 5 7 Carefully tuck all wires and splices into the switch housing 1 8 Attach the cover light fitter 5 6 to the switch assembly housing 1 using the two screws 2 that were removed in Step 2 Figure 4 9 Proceed to Installation of Glass Bowl section A WARNING To avoid fire or electrical shock be careful not to pinch wires between the switch housing assembly and the cover Installation of Glass Bowl 4 WARNING To avoid fire hazard do not exceed wattage indicated on the fixture NOTE Some light kit models provide a hole in the glass bowl for the fan switch chain While other light kit models provide a bowl cap including a hole for the fan switch chain and light switch chain 4 WARNIN2. G Over lamping the light kit will result in the lamps being automatically shut off Use only 60 watt maximum candelabra lamps Turn off electricity before replacing the lamps 1 Install three 60 watt maximum candelabra base bulbs into the fitter sockets 2 Depending on the model purchased insert the fan speed control switch chain through the offset hole in the glass bowl or the hole in the bowl cap 3 Install the light switch chain through the center of the finial nut Screw the finial nut finger tight onto the fitters threaded nipple CAUTION Be sure that the fan switch chain does not make contact with the light bulbs If necessary reposition the light fitter to avoid the fan switch chain from touching the light bulbs 4 Install pendants onto light fixture chain and fan switch chain NOTE It is advisable to periodically check the tightness of the finial 5 Installation is complete Turn on electricity at main fuse or circuit breaker box FAN SWITCH CHAIN NOTE YOUR GLASS MAY NOT LOOK THE SAME AS THE ONE IN THIS LIGHT FITTER BOWL CAP IT INSTALLS IN A SIMILAR THREADED vee er MANNER i 1 GLASS OUTER BOWL CAP BOWL not on all light kits 3 FINIAL LIGHT SWITCH CHAIN Figure 6 PENDANTS 2 For repair parts phone 1 800 654 3545 Ls a o EMERSON Air Comfort Products DIVISION OF EMERSON ELECTRIC CO 8100 W Florissant St
3. LY 7 LIGHT FITTER NOTE YOUR FITTER MAY NOT LOOK THE SAME AS THE ONE IN THIS ILLUSTRATION HOWEVER IT INSTALLS IN A SIMILAR MANNER BOWL CAP Figure 2 Zp 2p To avoid possible fire or electrical shock make certain no bare wire strands are exposed outside wire connectors Figure 3 4 WARNING To avoid possible fire or electric shock be careful not to pinch wires between switch cup and the cover plate 13 Proceed to Installation of Glass Bowl section Installation on Emerson Fans Having Two Piece Die Cast Switch Housings 1 Remove all parts and parts packages from carton A WARNING To avoid possible electric shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring 2 Remove the cover 5 from the fan switch housing 1 by removing the two outer screws 2 See Figure 4 FAN SWITCH CHAIN 3 WIRE CONNECTORS 1 SWITCH HOUSING ASSEMBLY BLUE WIRE WHITE WIRES 9 HEX NUT 8 LOCKWASHER BLACK WIRE 5 COVER 2 SCREWS 4 CENTER SCREW ao 6 LIGHT FITTER 7 BOWL CAP Figure 4 3 Remove the center screw 4 from the cover 5 Insert the black and white wires from the light kit fitter 6 thru the hole and thread the switch housing cover tightly onto the light kit fitter NOTE Wet location plate can not be used with two piece die cast switch housing 4 Insert the black and white wires throu
4. Louis MO 63136 Part No F40BP74510000 Form No BP7451 Printed in China 11 11 ILLUSTRATION HOWEVER READ AND SAVE THESE INSTRUCTIONS Ceiling Fan Light Fixture SUITABLE FOR WET LOCATIONS THREE 60 WATT CANDELABRA BULBS USE THESE FIXTURES ONLY WITH EMERSON CF SERIES CEILING FANS NOTE ANY LIGHT KIT OR FITTER AND GLASS COMBINATION COVERED BY THIS MANUAL WEIGHS 5 8 LBS OR LESS Ceiling Fan Light Fixture EMERSON Owner s Manual LIMITED WARRANTY What The Warranty Covers All products covered by this Owner s Manual are warranted against all defects in workmanship and materials You must be the original purchaser or user of the product to be covered What The Period Of Coverage Is All components are covered by this warranty for one year from the date you purchased your light fixture ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR What Will Emerson Electric Co Do To Correct Problems Emerson Electric Co will replace a defective Emerson Light Fixture at no charge to you WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON How Can You Get Service YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE You can r
5. cethe rubber washer on the top of the wet location plate then place the light fitter through the center hole of the wet location plate secure with lockwasher and nut Figure 2 8 Insert the black and white wires through the lockwasher 8 and hex nut 9 supplied Firmly tighten the hex nut to secure the light kit fitter to the switch cup 9 Connect the white neutral wire from the switch cup to the white neutral wire of the light fixture Figure 2 Connect the blue line hot wire from the switch cup to the black line hot wire of the light fixture Use listed wire connections previously removed in step 5 to make connections Figures 2 and 3 The neutral and line hot wires must be installed as instructed to maintain proper polarly at the lampholders 10 Carefully tuck all wires and splices into the switch cup 1 Figure 2 11 Connect the motor connector 4 to the switch cup connector 5 12 Position the switch cup 1 and fitter assembly 7 on the cover plate 2 and install the three screws 3 that were previously removed in Step 2 and tighten securely 2 COVER PLATE 4 MOTOR CONNECTOR 5 SWITCH CUP BLACK WIRE CONNECTOR Sy 4 6 WIRE ACO HEX NUT CONNECTORS 3 SCREWS gt WHITE WIRES 8 LOCKWASHER H eed 1 SWITCH CUP Le CHAIN HEX NUT LOGKWASHER gt RUBBER WASHER WLP100 WET LOCATION PLATE PURCHASED j SEPERATE
6. eturn the product to our factory or to your nearest authorized service center e To return the product to the factory obtain a return authorization and service identification tag by writing to Air Comfort Products Division of Emerson Electric Co 8100 W Florissant Ave St Louis MO 63136 Include all model numbers shown on the product with your request e To return the product to an authorized service center call 1 800 654 3545 for the address of the nearest authorized service center You will be responsible for all insurance freight or other transportation charges to our factory or authorized service center Your Emerson Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage What Is Not Covered This warranty also does not cover any defects malfunctions or failures caused by e Repairs by persons not authorized by Emerson Electric Co e Use of parts or accessories not authorized by Emerson Electric Co e Mishandling improper installation modifications or damage to your light fixture while in your possession or Unreasonable use misuse abuse including failing to do reasonable and necessary maintenance and normal wear and tear Additionally this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when e The original purchaser or user ceases to own the product or e The ceiling fan is moved from its original point of i
7. gh the lockwasher 8 and hex nut 9 supplied Firmly tighten the hex nut to secure the light kit fitter to the switch housing cover 5
8. nstallation This warranty is only valid within the 50 states of the United States and the District of Columbia No other written or oral warranties apply and no employee agent dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co REPAIR REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES Incidental damages include but are not limited to such damages as loss of time and loss of use Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly How State Law Relates To The Warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Form No BP7451 ETL Model No LK140 amp LK141 Part No F40BP74510000 A WARNING Safety Instructions To avoid fire shock and serious personal injury follow all instructions carefully 1 Read your Owner s Manual carefully before installing the light fixture Retain Owner s Manual for future reference 2 Be careful of the fan and blades when cleaning painting or working near the fan Before installing
9. or servicing the light fixture or ceiling fan switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Do not exceed the wattage indicated on fixture ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring Make certain no bare wires are exposed outside the wire connectors All wiring must conform to national and local electrical codes Follow the recommended instructions for the proper method of wiring your new light fixture If you feel you do not have enough electrical wiring knowledge or experience have your light fixture installed by a licensed electrician Any electrical work not described in this manual should be performed by a licensed electrician WLP100 wet location plate must be installed on light kit when used in wet locations WARNING To reduce the risk of possible fire and electrical shock install only on Emerson Ceiling Fan models CF552 CF542 CF620 CF680 CF654 in wet locations with the WLP100 wet location plate Permissible to use this light kit on models CF788 CF787 CF130 CF742 and CF652 installed in indoor or damp locations Permissible to use this light kit on all Emerson CF model ceiling fans in
10. stalled in indoor locations Assembly and Installation A WARNING Do not install or use the light fixture if any part is missing or damaged Call toll free 1 800 654 3545 A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring Installation on Emerson Fans Having a Modular Switch Cup with Center Screw 1 Remove all parts and parts packages from the carton 2 Remove the switch cup 1 from the cover plate 2 by removing the three screws 3 around the side of the switch cup Figure 1 3 Disconnect the motor connector 4 from the switch cup connector 5 Figure 1 2 4 Remove the center screw 6 from the switch cup Figure 1 5 Carefully locate the white and blue wires labeled either L or LIGHT in the switch cup and remove the wire connectors from the wires 6 Insert the black and white wires from the light fitter 7 through the center hole in the switch cup Figure 2 and thread the switch cup onto the light fitter Hold wires taut while installing switch cup to prevent the wires from twisting 4 MOTOR 2 COVER PLATE CONNECTOR 5 SWITCH CUP 3 SCREWS eee CONNECTOR 1 SWITCH CUP 6 CENTER SCREW Figure 1 7 If installing in a wet location Install the light fitter on plate using the lockwasher nut and rubber washer supplied with the WLP100 purchased seperately wet location plate Pla
Download Pdf Manuals
Related Search