Emerson CF875 Owner's Manual
Contents
1. Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing Do not put anything into the fan blades while they are turning Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades All wiring must be in accordance with the National Electrical Codes ANSI NFPA 70 1999 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be repla2. Fan Together 3 Mount the blade flanges to the fan blades using three 3 16 24 x 9 32 screws per blade Figure 7 Repeat for four remaining blades A WARNING To reduce the risk of personal injury do not bend the _ 1 Screw four 7 watt 120 volt light bulbs into the sock ets on the mounting plate light fitter 2 Install two 3 16 24 x 3 8 screws several turns into screw holes on opposite sides of the mounting plate light fitter Figure 6 Position the crystal glass housing so that the keyhole slots in the crystal glass housing engage with the two screws Turn the housing to the right so the keyhole slots rest on the screws tighten the screws Install the other two 3 16 24 x 3 8 screws blade flanges when installing the flanges balancing the blades or cleaning the fan KEYHOLE SLOT 3 16 24 x 3 8 SCREW LD WY 3 3 16 24 x 9 32 SCREWS Figure 6 BLADE FLANGE Figure 7 5 FAN BLADE 4 Attach one blade assembly to the motor using two 1 4 20 x 1 2 phillips head blade flange screws Figure 8 Make sure the screws are tightened securely Repeat this procedure for the other four blade assemblies NOTE Take care not to scratch the fan housing when installing the blade assemblies CRYSTAL FAN BLADE FLANGE 0x wer ASSEMBLY 1 4 20 x 1 2 PHILLIPS HEAD SCREWS Figure 8 housing light fitter with the motor connector Figure 9 Match the colo
3. TO OBTAIN LIMITED WARRANTY SERVICE KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE You can return the product to our factory or to your nearest authorized service center e To return the product to the factory obtain a return authorization and service identification tag by writing to Air Comfort Products Division of Emerson Electric Co 8100 W Florissant Ave St Louis MO 63136 Include all model numbers shown on the product with your request e To return the product to an authorized service center call 1 800 654 3545 for the address of the nearest authorized service center You will be responsible for all insurance freight or other transportation charges to our factory or authorized service center Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage What Is Not Covered The glass globes and light bulbs of your ceiling fan are not covered by this warranty This warranty also does not cover any defects malfunctions or failures caused by e Repairs by persons not authorized by Emerson Electric Co e Use of parts or accessories not authorized by Emerson Electric Co e Mishandling improper installation modifications or damage to your ceiling fan while in your possession or e Unreasonable use misuse abuse including failing to do reasonable and necessary maintenance and normal wear and tear Additionally this warranty and any implied warranty of m
4. 2 06
5. Check to see that you have received the following parts Crystal glass housing Mounting plate light fitter Motor assembly Switch housing light fitter Four glass shades Five fan blades Five blade flanges One loose parts bag containing Fifteen 3 16 24 x 9 32 phillips head screws Ten 1 8 20 x 1 2 phillips head screws One wood ball Small with chain One wood ball large with chain Three wire connectors Four 3 16 24 x 3 8 phillips head screws Three wire connectors 8 Four Nuts Hexlock 1 4 20 NOTE Place the parts from the loose parts bag in a small container to keep them from being lost If any parts are missing contact your local retail or catalog outlet for replacement before proceeding TO Daon NOOR WD Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit 4 WARNING The outlet box must be securely anchored and capa Turning off wall switch is not sufficient To avoid ble of withstanding a load of at least 50 pounds possible electrical shock be sure electricity is A WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly groun
6. READ AND SAVE THESE INSTRUCTIONS Min P gt EMERSON CRYSTAL LX odai No Ceiling Fan CF375SPBO00 Owner s Manual Net Weight 21 3 Lbs LIMITED WARRANTY What The Warranty Covers This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials You must be the original purchaser or user of the product to be covered What The Period Of Coverage Is As it applies to the motor this warranty will last for a lifetime of your ceiling fan All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR What Will Emerson Electric Co Do To Correct Problems Emerson Electric Co will replace a defective Emerson Air Comfort Ceiling Fan motor blade component or other accessory at no charge to you If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided Emerson Electric Co will refund the actual purchase price of your fan We will ship the repaired product or replacement to you at no charge but you are responsible for all costs or removal reinstallation and shipping of the product to Emerson Electric Co How Can You Get Service YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN
7. ced Consult a qualified electrician if in doubt The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance for an 8 foot ceiling The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician WARNING To avoid fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use this product by Emerson Electric Co could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades WARNING To reduce the risk of electric shock this fan must be installed with an isolating wall control switch DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Yo
8. ct the fan motor white wire and the mounting plate light fitter white wire to the supply white neutral wire using wire connector supplied Figure 5 Connect the fan motor black wire and blue wire to the supply black hot wire using wire connector supplied Figure 5 Your fan is now wired to be turned on and off from the fan switch After connec tions have been made turn leads upward and care fully push leads up into the outlet box WARNING To avoid risk of fire or shock check to see that all A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box or circuit breaker before wiring NOTE If you are not sure if the outlet box is ground ed contact a licensed electrician for advise for it must be grounded for safe operation Connect the green grounding wire from the motor bracket and the green wire from the mounting plate light fitter to the grounding conductor of sup ply this may be a bare wire or wire with green col ored insulation Securely connect wires with wire connector supplied Figure 5 120V SUPPLY WHTIE connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result GROUND BLACK 5 Return to Step 3 of section HOW TO HANG YOUR CEILING FAN Figure 5 How To Put Your Ceiling
9. d Pull Medium 3rd Pull Low 4th Pull OFF All fans are shipped from the factory with the re vers ing switch positioned to circulate air downward If air flow is desired in opposite direction turn your fan off and wait for the blades to stop turning then slide the REVERSING N SWITCH A LIGHT SWITCH PULL CHAIN FAN SWITCH PULL CHAIN j Figure 12 4 WARNING FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER B EFORE TROUBLE SHOOTING YOUR FAN Trouble Shooting 1 Fan will not Reversing switch in neutral position start Fuse or circuit breaker blown Make sure reversing switch position is all the way to one side Check main and branch circuit fuses or circuit breakers Loose power line connections to the fan Check line wire connections to fan and or loose switch wire connections in switch switch wire connections in the switch housing light fitter 2 Fan sounds Blades not attached to fan noisy Screws securing fan blade flanges to motor are loose housing light fitter Attach blades to fan before operating Check to make sure the screws which attach the fan blade flanges to the motor are tight Wire connectors inside switch housing light Check to make sure wire connectors fitter rattling in switch housing light fitter are not rattling against each other or against the interior wall of the switch housing light fitter Scr
10. ded as a precaution against possible electrical shock A WARNING To avoid fire or shock follow all wiring instructions carefully outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt a l Any electrical work not described in these If your fan is to replace an existing ceiling light fixture instructions should be done or approved by a turn electricity off at the main fuse box at this time and licensed electrician remove the existing light fixture How to Hang Your Ceiling Fan A WARNING The fan must be hung with at least 7 of clearance ap from floor to blades Figure 1 suspended Figure 3 Then connect wiring to your fan according to section HOW TO WIRE YOUR H CEILINGS MOUNTING PLATE 2 Carefully lift the motor assembly and engage the slot in the motor bracket with the hook on the mounting plate light fitter so that it is securely LIGHT FITTER AT LEAST T THREADED TUDS 4 Figure 1 STUDS 4 a pry a Z WIRE LEADS MA WARNING The outlet box must be securely anchored and capable l of withstanding a load of at least 50 Ibs Figure 3 AT _ 3 Once wiring is completed lift the motor bracket so WARNING that the four threaded studs on the mounting plate light fitter protrude through the four holes in the motor bracket See Figure 4 To reduce the
11. erchantability or fitness for a particular purpose are voided when e The original purchaser or user ceases to own the product or e The fan is moved from its original point of installation This warranty is only valid within the 50 states of the United States and the District of Columbia No other written or oral warranties apply and no employee agent dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co REPAIR REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES Incidental damages include but are not limited to such damages as loss of time and loss of use Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly How State Law Relates To The Warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Part No F40BP71930002 Form No BP7193 2 U L Model No CF875 WARNING WARNING To avoid fire shock and serious personal injury follow these instructions Safety Instructions Read your owner s manual carefully and keep it for future reference
12. ews holding flanges to blades are loose Tighten screws securely 3 Fan wobbles 1 Screws securing fan blade flanges to or shakes motor are loose excessively 2 Fan blade flanges not seated properly 3 Mounting plate light fitter and or ceiling outlet box are not securely fastened 4 Fan blades out of balance 1 Check to be sure screws which attach the fan blade flanges to the motor are tight 2 Check to be sure the fan blade flanges seat firmly and uniformly to the surface of the motor If flanges are seated incorrectly loosen the screws and retighten 3 Tighten the mounting plate light fitter screws to the outlet box and or secure outlet box 4 Interchanging an adjacent side by side blade pair can redistribute the weight and result in smoother operation Maintenance IMPORTANT CARE INSTRUCTIONS For Your Ceiling Fan Periodic cleaning of your new Ceiling fan is the only maintenance that is needed When cleaning use only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to finish A WARNING Do not use water when cleaning your ceiling fan It could damage the motor or the blades and create the possibility of an electrical shock Accessories 1 Emerson speed controls see store or catalog A WARNING To reduce the risk of fire or electrical shock do not use fan with any solid state speed contr
13. lace the 60 watt maximum intermediate base light bulbs in the light kit turn off the electricity at the wall switch and simply unscrew the bulbs from the sockets and screw in new ones To replace the 7 watt maximum candelabra base light bulbs in the crystal glass housing first turn off the electricity at the main fuse box or circuit breaker panel Remove the switch housing light fitter and 6 disconnect the connector Remove the five fan blades then loosen the two screws at the two keyhole slots at the top of the crystal glass housing and remove the two screws at the two slotted holes Turn the crystal glass housing to the left and carefully remove the housing Replace the burned out 7 watt candelbra base bulbs and then install the crystal glass housing the five fan blades and the switch housing light fitter 1 2 Using Your Ceiling Fan Restore electrical power to the electrical box by turn ing the electricity on at the main fuse box or circuit breaker panel reversing switch to opposite position and turn fan on again The fan blades will turn in the opposite direc tion and reverse the airflow Check the operation of the fan by gently pulling on the 4 Check the operation of the light fixture by gently pulling on the light switch pull chain fan switch pull chain Your fan model is equipped with a 4 position 3 speed fan pull chain switch The operating sequence is as follows 1st Pull High 2n
14. ol device WARNING The use of any other control not specifically approved for this fan could result in fire shock and personal injury A WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or acces sories not designated for use with this product by Emerson could result in personal injury or property damage 1 Repair Parts Listing Part Number Key Model No Description CF875SPB00 1 Switch Housing Light Fitter Assembly 761653 3 Glass Shade set of 4 761656 Flange Assembly 761652 set of 5 set of 5 Loose Parts Bag Containing Blade Hardware Hanging Hardware Pull Chain Ball Blade Assembly 761548 761555 2 5 Crystal Glass Housing 761657 BP7193 2 Before discarding packaging material be certain all parts have been removed HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INFORMATION e PART NUMBER PART DESCRIPTION e NAME OF ITEM _ MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing For repair parts phone 1 800 654 3545 Owner s Manual 5 Ss eee KE EMERSON Air Comfort Products Form No BP7193 2 Part No BP71930002 DIVISION OF EMERSON ELECTRIC CO 8100 W Florissant e St Louis MO 63136 Printed in China 1
15. r stripes on the two connectors and push together until fully seated and latched LATCH HH SWITCH HOUSING LIGHT FITTER CONNECTOR MOTOR MOTOR CONNECTOR CONNECTOR Figure 9 SWITCH HOUSING LIGHT FITTER CONNECTOR 6 Position the switch housing light fitter on the switch housing plate and align the holes in the switch housing light fitter with the holes in the plate Secure by installing three 5 32 x 1 4 screws Figure 10 A WARNING To avoid possible fire or shock do not pinch wire between the switch housing light fitter and the plate SWITCH HOUSING PLATE SWITCH HOUSING 5 32 x 1 4 BSS SCREWS 3 gt LIGHT FITTER Figure 10 N i gt 5 Engage the color coded connector of the switch 7 Back out the three thumb screws in one shade holder until the shade neck slips into the holder Then tighten the thumb screws until they touch the neck with approximate equal projection on the out side Figure 11 Repeat for the other three shades Never use pliers to tighten the thumb screws or a broken or damaged shade may result WARNING Periodically check the tightness of the tightness of the knurled screws Fan operation may loosen these screws causing the shade to fall out A WARNING To avoid fire hazard use 60 watt or less rated intermediate base bulbs HOLDER _ GLASS SHADE KNURLED SCREW 3 PER SHADE Figure 11 Replacement of Light Bulbs To rep
16. risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt To avoid possible fire or shock make sure that the electrical wires are not pinched between the motor bracket and the mounting plate light fitter 1 Pass the supply wires black white and ground through the center hole and securely attach the _ 4 Securely tighten the four locknuts supplied onto mounting plate light fitter to the outlet box Figure 2 the threaded studs Fasten locknuts securely then using the two screws supplied with the outlet box try to shake the motor bracket to ensure that the assembly is tight Proceed to section HOW TO ws VU MOUNTING PLATE Hook MOUN ING PEATE e MOTOR LIGHT FITTER eee BRACKET FOUR 1 4 20 Eee PUT YOUR CEILING FAN TOGETHER NIN i LOCKNUTS TWO SCREWS SUPPLIED Figure 2 WITH OUTLET BOX SUPPLIED Figure 4 MOTOR How To Wire Your Ceiling Fan If you feel that you do not have enough wiring 2 Securely connect the motor orange wire to the knowledge or experience have your fan installed mounting plate light fitter orange wire using wire by a licensed electrician connector supplied Figure 5 _ 3 Securely conne
17. ur Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One 1 4 blade screwdriver One stepladder One wire stripper Four 60 watt maximum intermediate base bulbs Four 7 watt maximum candelabra base bulbs MATERIALS Wiring electrical box and box connectors must be of type required by local code The minimum wire would be a 3 conductor 2 wire with ground of size shown at right Installed Wire Length Wire Size A W G Up to 50 ft 14 50 100 ft 12 WARNING Before assembly your ceiling fan refer to section on proper method of wiring your fan page 5 If you feel you do not have enough wiring knowledge or experi ence have your fan installed by a licensed electrician Unpacking Instructions For your convenience check off boxes are provide next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted A WARNING Do not install or use fan if any part is damaged or missing Call Toll Free 1 800 654 3545 WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or acces sories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage C 1
Download Pdf Manuals
Related Search