Elkay EDFPVR217RC User's Manual
Contents
1. ALL 1 800 323 0620 ELKAY MANUFACTURING COMPANY 2222 CAMDEN COURT OAK BROOK IL 60523 630 574 8484 PAGE 5 98409C Rev B 9 082. ALVM GN3931 G Old ULLUOEL 8 S JULUOET BS a le i PAGE 2 L WVLAG NIHONOH IZ1GHAd4G4 m TANYd MOVA ALISOdWO9 o S 5 EDFPVR217RC INSTALLATION INSTRUCTIONS COMPOSITE BACK PANEL Wall should already be framed for the fountain using the positioning dimensions shown in Fig 2 Shown dimensions pertain to installation location framing must support up to 150 lbs weight Install rough in plumbing as shown in Fig 2 Run supply water inlet line and connect to a service stop not provided Turn on supply water and flush thoroughly Close water supply Remove bottom access panel from fountain basin and save the screws Install the fountain to the back panel and wall using 4 5 16 bolts and washers not provided Bolts should be long enough to securely fasten the fountain to the wall Tighten securely but do not over tighten Over tightening will crack the Marblyte Fountain Remove elbow from end of p trap item 1 and attach it to drain tube Re attach elbow to p trap and cut waste tube to required length using plumbing hadware and trap as guide Make water supply connections from service stop to the fountain strainer Item 16 by inserting the water inlet line into the inlet side of strainer until it rea
3. Cleaners left standing on the fountain surface can dull the surface finish Be certain to rinse all cleaning agents completely and polish with a soft cloth Harsh abrasive cleaners are not required and should not be used Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches and stains Cigarette burns can normally be removed without noticeable effect Deeper scratches or gouges can be corrected with fine grit sandpaper 240 grit then 400 grit or a green Scotchbrite pad To maintain or regain luster and make cleaning easier periodic applications of automobile wax or like products will keep the finish looking like new EDFPVR217RC SEE FIG 7 EDFPVR217RC PARTS LIST ITEM PARTNO DESCRIPTION Drain Screw 10 24 x 1 2 PH TR HD Z Nut Reg Retain 1 1 8 24 Bottom Plate HRFG E Bottom Plate HRFG S Strainer Beehive Hex Nut Ferrule Tailpipe Push Button Push Button Sleeve Regulator Holder Bubbler Assy VR Push Button Extension Fountain Galaxy Gray HRFG E 55969C Fountain Galaxy Gray HRFG S 61313C Regulator 7567268 Screw 55996C Strainer 56114C Panel Dbl Back Galaxy Gray 70012C Bubbler Locknut 755756 Ball Anti Rotation 755546 Insert Threaded 15029C Nipple Assembly 45736C Nut Reg
4. EDFPVR217RC Installation Care Use manual Non Refrigerated Composite VR Fountain with Back Panel Installer To assure you install this model easily and correctly PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING ELECTRICAL AND OTHER APPLICABLE CODES After installation leave these instruc tions inside the fountain for future reference IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANT INSTALLER PLEASE NOTE THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE COMPUTERS ETC TO WATER LINES ISA COMMON PROCEDURE THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE ORAN INCREASE IN THE METAL CONTENT OF THE WATER THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM 98409C Rev B 9 08 EDFPVR217RC GAHSINaNA 1 SNIYLNNO1 40 LHOddNS HAdOHd HOS ASAHLNI SI LHOddNS SNIN90719 7 1VM OL NIVLNNOJ 9ONIHN93S SATOH ONILNNOM p L 1 LATLNO ALSVM NOILVDO71 GAGNAWNODSY 193NNO9 AENL 424d09 GALVIdNN GO 8 NOILVDOT AlddNS H
5. ches a positive stop about 3 4 See Figure 6 Page 7 Turn on water supply and check for leaks Newly installed water supply line should be insulated after leak check is completed DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O RINGS MAY RESULT These products are designed to operate on 20 105 PSIG supply line pressure If inlet pressure is above 105 PSIG a pressure regulator must be installed in the supply line Any damage caused by reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG is not covered by warranty Check stream height from bubbler Stream height is factory set at 45 50 PSI If supply pressure varies greatly from this adjust the screw on regulator item 14 by using a small screwdriver through the small hole in the push button item 8 See Fig 3 Clockwise adjustment will raise stream height and counter clockwise adjustment will lower stream height For best adjustment stream height should be approxi mately 1 1 2 38mm above the bubbler Replace bottom access panel to fountain basin using screws provided Tighten securely Care and Maintenance of ELKAY Composite Fountains Elkay Composite fountains provide an exremely durable nonporous surface which resists staining Care is very simple Routine cleaning with a soft sponge or cloth or with water or non abrasive aerosol foam cleaner is all that is normally needed to give many years of trouble free service
6. ulator Mounting 56092C Poly Tubing Cut To Length 756746 Wrench Allen 7 64 3 8 O D UNPLATED 1 4 O D TUBE COPPER TUBE CONNECT OPERATION OF QUICK CONNECT FI INGS WATER INLET COLD WATER SUPPLY TO COOLER BUILDING WATER INLET SIMPLY PUSH IN TUBE IS PUSH IN COLLET TUBE TO ATTACH SECURED TO RELEASE TUBE IN POSITION aa Z Z 2 TE WATER FL PUSHING TUBE IN BEFORE DIRECTION SERVICE STOP PULLING IT OUT HELPS TO NOT FURNISHED RELEASE TUBE TROUBLE SHOOTING amp MAINTENANCE Orifice Assy Mineral deposits on orifice can cause water flow to spurt or not regulate Mineral deposits may be removed from the orifice with a small round file not over 1 8 diameter or small diameter wire CAUTION DO NOT file or cut orifice material Stream Regulator If orifice is free of material deposits regulate flow as in instructions on page 3 Step 9 or page 5 Step 7 If replacement is necessary see parts list for correct regulator part number Actuation of Quick Connect Water Fittings Cooler is provided with lead free connectors which utilize an o ring water seal To remove tubing from the fitting relieve water pressure push in on the gray collar while pulling on the tubing See Figure 6 Page 7 To insert tubing push tube straight into fitting until it reaches a positive stop approximately 3 4 PRINTEDSIN A FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR C
Download Pdf Manuals
Related Search