Elkay 4595 User's Manual
Contents
1. TO FOUNTAIN A 3 8 O D UNPLATED COPPER TUBE CONNECT COLD WATER SUPPLY BUILDING WATER INLET 0 fh L NOTE WATER FLOW DIRECTION SERVICE STOP NOT FURNISHED FIG 6 FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1 800 323 0620 97460C Rev SIB 6 06 Page 42. 4595 _ FTN Owners Manual Model 4595 Pedestal Barrier Free Stone Fountain k O gt INSTALLER To assure you install your 4595 Stone Fountain model easily and correctly PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING ELECTRICAL AND OTHER APPLICABLE CODES After installation leave these instructions with the Fountain for future reference IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANT INSTALLER PLEASE NOTE THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE COMPUTERS ETC TO WATER LINES IS A COMMON PROCEDURE THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM General Installation Tips 1 Water supply 3 8 O D unplated copper tube Waste 1 1 4 IPS Contractor to supply waste trap and service stop valve in accordance with local code 2 Connecting lines to be made of unplated copper and should be thoroughly flushed to remove all fore
3. d for inlet water pressure of 20 105 PSI A pressure reducing regulator should be used if the inlet water supply exceeds 105 PSI 5 Connect water supply and fountain drain Water connection and drain must comply with local codes 6 Turn on water supply and check all connections for leaks 97460C Rev SIB 6 06 Page 2 4595 _ FTN BUBBLER DETAIL a S See Fig 3 11 2 38mm 1 1 2 38mm STREAM HEIGHT ADJUSTMENT Stream height is factory set at 35 PSI If supply pressure varies greatly from this remove items 7 and 8 See Fig 3 and adjust screw on item 19 Clockwise adjustment will raise stream and counter clockwise adjustment will lower stream For best adjustment stream should hit basin approx 6 1 2 from bubbler FIG 4 Page 3 97460C Rev SIB 6 06 100147140560 100322740560 101570540560 15005C 15013C 170705042830 40048C 40089C 400942308640 98287C 40169C 40250C 45476C 50986C 55913C 55996C 56092C 56121C 600985551640 61313C 66346C 70682C 70683C 75588C 75589C MP PO PP HAH a Baa aoa a RONACOMNDATDRONAGOPOPNOUKRWN 4595 FTN PARTS LIST ITEM NO PART NO DESCRIPTION Drain Gasket Bubbler Gasket Drain Gasket Regulator Retaining Nut Bubbler T
4. ign matter before being connected to fountain This fountain is manufactured in such a manner that it does not in any way cause taste odor color or sediment problems 3 Connect fountain to supply line with a shut off valve and install a 3 8 unplated copper water line between the valve and the cooler Remove any burrs from outside of water line Push the tubes straight into the fittings until they reach a positive stop approximately 3 4 See Fig 6 DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O RINGS MAY RESULT 4 These products are designed to operate on 20 psig to 105 psig supply line pressure If inlet pressure is above 105 psig a pressure regulator must be installed in the supply line Any damage caused by reason of connecting this product to supply line pressures lower than 20 psig or higher than 105 psig is not covered by warranty Page 1 97460C Rev SIB 6 06 4595_FTN DRAIN AND WATER INLET LOCATION DETAIL 1 2 X 3 4 SLOT Ey Ope aD DRAIN saaa WATER INLET Installation Instructions 1 This fountain is to be mounted on a smooth flat finished surface with adequate support structure NOTE Mounting structure must be capable of supporting 300 Ib load on fountain 2 Refer to rough in for plumbing 3 Install shut off valve on water supply Valve not furnished 4 Locate and install fountain using 3 8 minimum screws or bolts Screws or bolts not furnished CAUTION This fountain is rate
5. ube Assy Basin Button Cover Nut Bubbler Bubbler Assembly Hex Nut 1 5 16 20UN Tailpipe 1 1 4 x 5 3 8 Drain Tube Regulator Holder Drain Adapter In Line Strainer Poly Tubing Cut To Length Drain Elbow 1 1 4 Drain Plug Assy Regulator Drain Tube Tee 1 4 Union 1 4 Slip Joint Nut 1 1 4 Gasket 0 SIMPLY PUSH IN TUBE TO ATTACH B TUBE IS SECURED IN POSITION a TROUBLE SHOOTING AND MAINTENANCE Orifice Assy Mineral deposits on orifice can cause water flow to spurt or not regulate Mineral deposits may be removed from the orifice with a small round file or small diameter wire CAUTION DO NOT file or cut orifice material Stream Regulator If orifice is clean regulate flow as in STREAM HEIGHT ADJUSTMENT instructions on page 3 If replacement is necessary see parts list for correct regulator part number Actuation of Quick Connect Water Fittings Fountain is provided with lead free connectors which utilize an o ring water seal To remove tubing from the fitting relieve water pressure push in on the gray collar while pulling on the tubing See Fig 5 To insert tubing push tube straight into fitting until it reaches a positive stop approximately 3 4 ERATION OF QUICK CONNECT FITTINGS PUSH IN COLLET TO RELEASE TUBE C PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO RELEASE TUBE PRINTED IN U S A 1 4 O D TUBE WATER INLET
Download Pdf Manuals
Related Search