Electrolux S670 User's Manual
Contents
1. cord exits the hood Step 3 Attach Outer Bag IMPORTANT To provide a good gasket seal the bag coupling must seat firmly against the motor base Hold outer bag with zipper away from the handle Line up screw holes Start the bag screws by hand then tighten with a screwdriver Loop the bag spring onto the bag support hook located at the back of the upper handle section Step 4 Store Electrical Cord The cleaner has two convenient cord storage hooks attached to the handle However some models feature a quick release cord hook on the upper handle A downward twist of the cord hook frees the cord for quick removal With either style wind the cord around the hooks for storage Fasten the plug to the cord to prevent unwinding N HOW TO USE The upright vacuum cleaner is designed to be used on multiple types of carpeting Do not attempt to use the upright vacuum cleaner on bare floors as damage to the floor covering may result Above the floor cleaning tools are available optional Handle Adjustment With the tip of the foot press down to release the handle lock located at the left rear side of the cleaner Move the handle and adjust it to the desired position for 1 storing upright 2 operating the cleaner at a comfortable height for the user and 3 cleaning underneath low furniture a ENN senor 3 Clean Underneath Handle Lock Power Switch The power switch is mounted on the hand2. in Turn off the switch and unplug the electrical cord when not in use and before servicing Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center before using Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Do not use extension cords or outlets with inadequate current carrying capacity Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow This vacuum cleaner creates suction and contains a revolving brush roll Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag in place Belt pulleys can become hot during normal use To prevent burns avoid touching the be
3. 69 Sanitaire SYSTEM_PRO Heavy Duty Upright Vacuum Cleaner Household Type Owner s Guide Model S670 Series IMPORTANT Do not return this product to the store Call 1 800 800 8975 Monday Friday 8 am to 7 30 pm CST and 10 am to 6 30 pm Saturday or visit our web site www sanitairevac com for any of the following e assembly problems replacement of broken or missing items A N to order replacement parts and accessories yo NN to locate the nearest Sanitaire Warranty Station E En Mexico llame al 55 5343 4384 Ns PLEASE RETAIN We suggest you record the model type and serial numbers below They are located on the silver rating plate on your cleaner For prompt and complete service information always refer to these numbers when inquiring about service Model amp Type Serial No www sanitairevac com It is also important to keep your receipt as proof of date of purchase Part No 75327 12 04 2004 Electrolux Home Care Products Ltd Printed in U S A Index Important Safeguards Service Information Assemble Dust Bag Brush Roll Belt Brush Roll Quick Kleen Fan Chamber Headlight Warranty GENERAL INFORMATION To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other The plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit co
4. CTROLUX HOME CARE PRODUCTS NORTH AMERICA Bloomington Illinois 61701 Household Warranty
5. Damages or malfunctions caused by negligence abuse or use not in accordance with the Owner s Guide e Defects or damages caused by unauthorized service or the use of other than Genuine Eureka Sanitaire parts hat Electrolux Home Care Products North America Will Do Electrolux Home Care Products North America will at its option repair or replace a defective cleaner or cleaner part that is covered by this warranty As a matter of warranty policy Electrolux Home Care Products North America will not refund the consumer s purchase price pended Warranty for Upright Cleaner Only The base of the Sanitaire Upright cleaner is warranted for five years from the original date of purchase xtended Warranty for SYSTEM_PRO Canisters The motor for SYSTEM_PRO canister cleaners is warranted for five years from the original date of purchase Warranty Registration Please fill out and return the warranty registration card accompanying your cleaner btaining Warranty Service To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Sanitaire Authorized Warranty Station You will find the nearest location in the Yellow Pages under Vacuum Cleaners Service and Repair Be certain that the Warranty Station is Sanitaire Authorized For the location of the nearest Sanitaire Authorized Warranty Station or for service information telephone toll free USA 1 800 800 8975 M
6. caps are in line with slots in cleaner base 6 Push brush roll into base 7 Place lower side of belt into belt guide and pull to stretch the belt around the left side of motor pulley Rotate pulley to secure belt into groove 8 Place slots of bottom plate over tabs of cleaner base 9 Seat and secure cam locks Ask for GENUINE EUREKA replacement belts No 52100A Look for the brea atta symbol Brush Roll The rotating brush roll sweeps and combs the carpet nap Keep the brush roll free from hair and threads so it will continue brushing When the bristles of the brush roll no longer touch a straight edge held across the bottom plate the brush roll is ineffective because the bristles no longer touch the carpet nap To maintain the most effective cleaning replace the wood brush roll Install new brush strips on the chromed steel brush roll refer to instructions How To Replace Worn Brush Strips PN 52282 4 chromed steel brush roll CAUTION Turn off the switch and unplug the electrical cord before replacing brush strips New brush strips are supplied in sets of two one long and one short To replace remove bottom plate and belt see How To Change Belt Then grasp center of brush roll and lift to remove A Remove rubber end cap cover G Slide in new brush strip of same available on select models from one end Unscrew locknut Remove end cap Remove shaft washer not included in ball bearing br
7. exico 55 5343 4384 www sanitairevac com Canada 1 800 800 8975 If you prefer you can write to Electrolux Home Care Products North America Service Division P O Box 3900 Peoria Illinois 61612 USA In Canada write to Electrolux Home Care Products North America 866 Langs Drive Cambridge Ontario N3H 2N7 If it is necessary to ship the cleaner outside your community to obtain warranty repair you must pay the shipping charges to the Sanitaire Authorized Warranty Station Return shipping charges will be paid by the Warranty Station When returning parts for repair please include the model type and serial numbers from the data plate on the cleaner urther Limitations and Exclusions Any warranty that may be implied in connection with your purchase or use of the cleaner including any warranty of Merchantability or any warranty for Fitness For A Particular Purpose is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Your relief for the breach of this warranty is limited to the relief expressly provided above In no event shall Electrolux be liable for any consequential or incidental damages you may incur in connection with your purchase or use of the cleaner Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives
8. le Push ON or OFF O Cleaner Height Setting WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting The front of the cleaner has an adjustment that raises or lowers the cleaner base to match the type of carpet With the cleaner cord unplugged set the adjustment to lowest setting for maximum cleaning If the cleaner is difficult to push move adjustment to next highest setting until cleaner is comfortable to push The brush roll must reach the carpet for effective cleaning Make each adjustment with cleaner switch off and cord disconnected from outlet For ease in moving the adjustment knob place handle in operating position and tilt cleaner back to remove weight from front wheels 4 HOW TO MAINTAIN The instructions given in this booklet serve as a guide to routine maintenance To avoid unnecessary service calls check the bag belt and brush roll often Disposable Dust Bags Paper bags play a very important role in the efficiency of a vacuum cleaner The purpose of a paper bag is to trap dirt But at the same time the paper bag must be porous enough to allow air to pass through If the paper bag becomes clogged no air can pass through the cleaner and no cleaning can take place regardless of how powerful the unit Change the dust bag frequen
9. lt pulley when servicing the drive belt Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Store your cleaner in a cool dry area Keep your work area well lighted Unplug electrical appliances before vacuuming them SAVE THESE INSTRUCTIONS HOW TO ASSEMBLE CAUTION Completely assemble vacuum cleaner before using Assembly Packet is with owner s guide vv A B C 2 Part Lower Bag Bolt Cord Hook Screws Step 1 Attach the Handle Push lower handle into handle socket on the base NOTE Check to be sure slot in handle is positioned correctly see Detail A Align the holes on the lower handle and the socket Insert a 2 part bolt A in the bottom center of the handle and tighten Push upper handle onto lower handle Make sure grip curves away from cleaner Align the holes on the upper handle to the holes on the lower handle Insert a 2 part bolt A in center of the handle and tighten Step 2 Attach Lower Cord Hook Make sure cord hook is pointing downwards Press the power cord into the groove on the cord hook pulling any slack toward the base of the cleaner On the cord hook find the curved tab and place in slot on lower handle section keep cord taut while pressing the cord hook to the left until it snaps into slot on opposite side of handle The hook should point downward on the same side that the
10. lts Air dry thoroughly before using DO NOT USE AN AUTOMATIC WASHER OR DRYER as either will cause abrasion to the delicate polyester fabric DO NOT DRY CLEAN as dry cleaning fluids will damage plastic parts of your bag assembly Brush Roll Belt The brush roll belt on the upright vacuum cleaner drives the brush to agitate sweep and comb the carpet nap The belt should be checked regularly to be sure it is in good condition Replace the belt if it is stretching cracking or slipping Cut away any hair or thread wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly How To Replace A Worn Belt Style RD PN 52100A CAUTION Turn off the switch and unplug the electrical cord before replacing belt Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt IMPORTANT Improper installation of the brush roll or brush roll belt could cause carpet or cleaner damage 2 Pull up on belt to rotate it off the motor pulley Lift up on brush roll and remove worn belt Check for brush wear see Brush Roll instructions on page 10 3 Place new belt around brush roll 4 Align brush roll pulley with belt guide OE Metal Brush Roll only Place rubber end cap covers available on select models over both end caps flat side against end cap Align holes and secure 5 Slant brush roll forward so end
11. ntact a qualified electrician to install the proper outlet Do not change the plug in any way The bag may have come dislodged in shipping Check the bag to insure proper seating before attempting to use the cleaner Do not operate the cleaner without a dust bag Damage may result to the motor The cleaner is designed to pick up dirt and dust particles Avoid picking up hard or sharp objects with the cleaner to avoid bag breakage or possible motor damage Service Information The instructions in this booklet serve as a guide to routine maintenance If additional service is required telephone toll free USA 1 800 800 8975 Mexico 55 5343 4384 Canada 1 800 800 8975 If you prefer you can write to Electrolux Home Care Products North America Consumer Service P O Box 3900 Peoria Illinois 61612 USA In Canada write to Electrolux Home Care Products North America 866 Langs Drive Cambridge Ontario N3H 2N7 Refer to The Sanitaire Limited Warranty for complete service information P DO NOT OIL the motor or the brush roll at NY any time The bearings are permanently lubricated and sealed IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Do not leave vacuum cleaner when plugged
12. remove the screws on either side of the fan cover as indicated by the arrows Push the cam locks outward against the wheels to lift the cover from the cleaner base Dirt and obstructions can easily be cleared however caked grease may need to be scraped from the cover and the cleaner If the fan does not turn freely it also should be removed for cleaning To remove the fan place a wrench over the motor pulley Hold the fan blades with one hand and turn the wrench counterclockwise Remove the motor pulley and lift the fan off the motor shaft Clean the area and replace the fan over the motor shaft Tighten the motor pulley snugly clockwise with the wrench If necessary replace the fan cover or the gasket with replacement parts Be sure the gasket is in place Reposition the fan cover by first placing the exhaust end into place between the large rear wheels Seat fan cover firmly Next replace the belt and bottom plate as the pressure from the bottom plate helps seal the fan cover Start the two screws by hand to be sure they are straight then tighten Order fan chamber cover replacement kit fan cover gasket two screws Part No 52334 Headlight Bulb Standard on most models CAUTION Turn off the switch and unplug the electrical cord before replacing headlight bulb Headlight style varies by model Locate the notches that release the tabs at either 1 top 2 side or 3 bottom of the lens as illustrated Place a screwdri
13. tly Some fine particles can restrict airflow very quickly and will decrease performance even before the bag appears to be full For that reason when vacuuming carpet fresheners or cleaners powder plaster dust or similar fine substances the bag may need to be changed more often How To Change Disposable Dust Bag Style F amp G PN 54924A CAUTION Turn off the switch and unplug the electrical cord before changing dust bag Never operate the vacuum cleaner without the dust bag 1 Pull 2 Roll down coil spring 3 Pull bag throat off sleeve 4 Unfold new bag 5 Place bag throat on sleeve 6 Roll up coil spring 7 Place paper bag into outer bag NOTE Be certain there are no folds at the top or bot tom of the paper bag 8 Lift zipper GENUINE Look for the Ers rmoLuer symbol Ask for GENUINE EUREKA dust bags Style F amp G Micron Filter Bag Care Micron Filter Bag is standard on some models Because the Micron Filter Bag is an effective filter medium occasionally trapped dust particles will need to be cleaned from the inside of it The dust accumulation can be vacuumed out with another vacuum or the bag may be removed to shake out If you desire the bag may be hand laundered The zipper on the bag should be down and the bag should remain right side out Use warm water 150 F 65 C and a mild detergent Pre soaking the bag in a laundry pre soak is desirable for best cleaning resu
14. ush roll E Remove bearing retainer F Push shaft through opposite end G Pull out worn brush strip with pliers U OW length rounded end first Fit track on either side into brush roll slot Replace second brush strip from opposite end of brush roll Replace shaft Align indentation on bearing retainer with brush strip on both ends of brush roll Replace shaft washer Position end cap with flat sides of center hole over flat sides of threaded shaft Tighten locknut Align holes and secure rubber end cap cover flat side against end cap When properly assembled the brush roll should rotate freely between the two end caps Check the condition of the belt change if necessary Replace the brush roll belt and bottom plate see How To Replace A Worn Belt Ask for GENUINE EUREKA replacement brush strip 12 inch No 52282 4 Quick Kleen Fan Chamber On some models CAUTION Turn off the switch and unplug the electrical cord before cleaning The clear removable fan chamber cover provides easy inspection cleaning and maintenance of the fan chamber Removing the cover provides easy access to the motor fan Grease buildup dirt or other obstructions visible through the fan cover should be removed To clean the fan area take off the chrome bottom plate by releasing the two cam locks see Brush Roll Belt Figure 1 and 2 Remove the belt from the motor pulley then loosen and
15. ver into one notch twist or pry the screwdriver to release the lens Repeat for the second notch on the opposite side Rotate the bulb socket forward Push bulb in and turn to remove Secure new bulb into socket and rotate bulb socket backward Replace the lens tabs into the top or the bottom of the hood opening Rotate lens to position and press down at each notch until the lens locks into position NOTE Use 25 watt replacement bulb only Ask for GENUINE EUREKA replacement bulb 40009A Cleaner Care CAUTION Turn off the switch and unplug the electrical cord before cleaning unit To keep the vacuum cleaner looking new it can be wiped with a damp cloth and a mild soap solution then thoroughly dried Never use any type of chemical as chemicals can damage the cleaner When not in use the cleaner should be stored in a clean dry place THE SANITAIRE LIMITED WARRANTY Wha This Warranty Covers Your Sanitaire cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of two years and five years for the motor and base assembly The warranty is granted only to the original purchaser and members of his or her immediate household The warranty is subject to the following provisions hat This Warranty Does Not Cover e Parts of the cleaner that require replacement under normal use such as disposable dust bags filters drive belts light bulbs and brush roll bristles e
16. you specific legal rights You may also have other rights which vary by state GENUINE EUREKA PRODUCT uestions amp Answers about Genuine Eureka Sanitaire Products Q Why should I use only Genuine Eureka Sanitaire paper bags belts and parts in my Eureka Sanitaire vacuum cleaner A Using Genuine Sanitaire Products which are made to our exacting specifications and engineered with emphasis on quality performance and customer satisfaction ensures the long life and cleaning efficiency of your vacuum cleaner Overall this saves you money and helps to keep your home clean Q How can I be sure I am using only Genuine Eureka Sanitaire products in my vacuum cleaner A Typically packaged products and paper bags can be identified by a Eureka or Sanitaire logo For further identification assistance you may call our toll free number 1 800 800 8975 for the location of a nearby Eureka Sanitaire Authorized Warranty Station Q Are there any differences between made to fit or imitation and Genuine Eureka Sanitaire paper bags belts and parts A Yes there are some very important differences in materials quality and reliability Many customers have mistakenly purchased imitation paper bags and parts while thinking they purchased genuine Unfortunately many of these customers discovered the differences after they experienced related difficulties For Genuine Sanitaire Value Accept No Imitations 69 Sanitaire ELE
Download Pdf Manuals
Related Search