Electrolux ESI 6220 User's Manual
Contents
1. Waterinlet Mains cable Water Mains drain socket Mains cable 33 Guarantee Conditions Standard guarantee conditions We Electrolux undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condi tion that e The appliance has been correctly installed and used only on the electricity supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manu facturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any per son not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre e Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect2. Do not use more detergent special salt or rinse aid than is recommended in these operating instructions and by the manufacturer of the respective product Appliance Features and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Spray Arm Spray Arms Water hardness switch Container for Special Salt Detergent Container for Rinse Aid Rating Plate Filters Control Panel Water softener Function button button Multidisplay poo Q 319 x ol O o 0 ba o O ____ e O O oy p o Q Wash programme Control Door handle ON OFF button buttons indicator Water softener and function button In addition to the indicated wash programme the dishwasher water softener can be set using a combination of these but tons The 3 lights onthe Top light multidisplay can display O Middle light e the current Bottom light stage of the wash pro gramme selected e which fault has occurred in the dishwasher The indicator has the following meaning Refill with special salt The control indicator never illuminates while a wash programme is running Prior to using for the first time Prior to using for the first time remove all the clips with which the dish baskets are secured for transport Then perform the following steps 1 Adjust the water softener 2 Filling w
3. 1 Fit the elbow to the drain hose 2 Secure the drain hose against sliding off the edge of the wash basin Pass a piece of cord through the hose elbow and fix it to the wall or the tap Leak Prevention System For protection from damage due to water leaks the dishwasher is equipped with a leak prevention sys tem In the event of a fault the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain pump is activated The remaining water in the appliance is automatically pumped out The leak prevention system also works when the appliance is switched off 240 cm 31 Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person A WARNING This appliance must be earthed The manufacturer declines any responsi bility should these safety measures not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug must still be accessible after the appliance has been installed Changing a fuse The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS 1363A fuse must be used Should the plug need to be replaced for any r
4. Off the Dish washer Switch off the dishwasher when is illuminated on the programme progress display 1 Press the ON OFF button The ON OFF but ton O indicator extinguishes Hot steam may escape from the appliance when opening the door immediately after the end of the programme Therefore 2 Open the door carefully Emptying the Dishwasher G e Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing them from the appliance e Leave the dishes in the dishwasher for approx 15 minutes after the end of the programme so that they dry better and can cool down e First empty the lower basket and then the upper rack By using this procedure you will avoid any water that may be remaining in the upper basket dripping onto the dishes in the lower basket and leaving water marks Care and Cleaning i Do not under any circumstances use furni ture care products or aggressive cleaners If necessary clean the controls only with a soft cloth and pure warm water Occasionally check the internal containers door seal and water inlet for soiling clean if necessary Cleaning the Filter Gi The filters in the base of the washing com partment are to a large extent self cleaning Nevertheless the filters should be checked and cleaned from time to time Dirty filters will degrade the washing result Open the door remove the lower basket The dishwasher filter syste
5. SL1 1DZ Tel 08705 950950 Calls may be recorded for training purposes 35 O Electrolux plc 2002 822 960 473 00 0303 Subject to change without notice lt The Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world
6. items such as knives To ensure that all items of cutlery are completely washed you should 2 Place short knives forks and spoons in the grid 1 Place the grid insert on the cutlery basket OS ORS WRB 2 707 WAY insert with their handles pointing downwards Some models of dishwasher have cutlery baskets without a cutlery grid 14 Loading Pans Frying Pans and Large Plates Load large and heavily soiled dishes in the lower bas ket Plates up to 29cm in diameter Your dishwasher has one of the following two types of lower basket Type 1 The rear plate insert in the lower basket can be removed To make it easier to load large dishes it is G possible to remove the plate inserts from the lower basket to move the cutlery basket sideways Type 2 The rear plate insert in the lower basket can be folded on its side To ease the loading of large items G the two rows of prongs in the rear plate insert can be folded across one another the cutlery basket in the lower basket can be moved to the side NON C Gap A 15 Loading Cups Glasses and Coffee Services Load small delicate items and long pointed cutlery in the upper basket M e Arrange plates and dishes offset on and under the folding cup racks so that
7. the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of Electrolux manufacture which are not marketed by Electrolux European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first pur chased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of prod ucts e This guarantee relates to you and cannot be transferred to another user 34 Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regula tions in your new country Before you move please contact your nearest Cus tomer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 6
8. too much foam will be formed during the wash Adjusting Rinse Aid Dosing O As the dishes are washed rinse aid is released from the dispenser into the wash water The dose is factory set at 4 and can be adjusted from 1 to 6 Only change the set ting if streaks milky spots or dried on water marks are visible on glasses or crockery 1 Open the door of the dishwasher Press the rinse aid compartment release button with your finger Fully open the rinse aid compartment lid Set the dose level Close the lid and press until it locks into place If rinse aid has run out wipe up with a cloth N oa kh WO af xi AS In Daily Use e s it necessary to refill with special salt or rinse aid e Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading cutlery and dishes Sponges household cloths and any object that can absorb water may not be washed in the dishwasher For washing in the dishwasher the following cutlery dishes are not suitable are of limited suitability Cutlery with wooden horn Only wash stoneware in the dishwasher if it is spe china or mother of pearl handles cifically marked as being dishwasher safe by the Plastic items that are not heat resistant manufacturer Older cutlery with cement that is
9. 2 20 13 Germany N rnberg 49 0 800 234 7378 Italy Pordernone 39 0 800 11 7511 Sweden Stockholm 46 0 20 78 77 50 UK Slough 44 0 1753 219898 Service and Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact Service Force by telephoning 08705 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading What to do if When you contact the Service Force Centre you will need to give the following details Your name address and post code Your telephone number Clear and concise details of the fault The model and serial number of the appliance found on the rating plate 5 The purchase date ON Please note that a valid purchase receipt or guaran tee documentation is required for in guarantee serv ice calls Customer Care For general enquiries concerning your Electrolux appliance or for further information on Electrolux products please contact our Customer Care Depart ment by letter or telephone at the address below or visit our website at www electrolux co uk Customer Care Department Electrolux 55 77 High Street Slough Berkshire
10. In the event of a fault first close the tap then switch off the appliance and unplug it from the mains If the appliance is permanently wired to the mains switch off the fuse s or unscrew them Y Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material cor rectly All the packaging materials used are harmless to the environment and can be recycled e Plastic parts are marked with standard interna tional abbreviations gt PE lt for polyethylene e g sheet wrapping material gt PS lt for polystyrene e g padding mate rial always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recy cled paper and should be deposited in the waste paper collection for recycling Disposal of old appliances As and when you cease to use your dishwasher please take it to a recycling centre or to your dealer who will for a small contribution to the costs dispose of it for you Y Economical and Ecological Dishwash ing e Only connect the dishwasher to the cold water supply e Ensure that the water softener is correctly adjusted Do not pre rinse dishes under running water When you wash a small load the load sensor cal culates the amount of water necessary and short ens the programme It is more economical to always wash with a full load e Select the wash programme to suit the nature and degree of the soiling on the dishes
11. User Instructions 00000000 E ESI 6220 ANC 822 960 473 00 0303 Dear customer Please read these user instructions carefully Above all please observe the safety instructions on the first few pages ofthese user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance A 1 7 The warning triangle and or specific words Warning Caution Important are used to highlight instructions that are important for your safety or for the function of the appli ance It is imperative that these instructions are observed Numbered instruction steps lead you step by step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appli ance are marked with a clover leaf In the event of a malfunction these operating instruc tions contain information on how to rectify faults your self see the What to do if section If these instructions are insufficient please contact your nearest Service Force Centre In this respect please read the Service and Spare Parts section at the rear of these user instructions Your dishwasher is fitted with the new PULSE WASH wash system With this wash system the motor speed and spray pressure are varied during the wash programme to improve the clea
12. alt for the Water Softener A Use only special salt for dishwashers Never fill the salt container with any another type of salt e g culinary salt or dishwasher deter gent This would irreparably damage the water softener Prior to filling with salt please check each time that you really do have a packet of spe cial salt in your hand Fill with special salt e Prior to using the dishwasher for the first time e When the SALT indicator Ne on the control panel is illuminated Gi If the water hardness in your area is less than 4 d you do not need to use special salt 1 Open the door remove the lower basket 2 Undo the lid on the salt container by turning it anti clockwise 3 Only when using for the first time fill the salt container with water 4 Place the funnel supplied on the container open ing Fill the container with special salt through the fun nel the capacity of the container is approx 1 0 1 5 kg depending on the grain size Do not overfill the salt container with special salt The water expelled by filling the salt con G tainer with special salt runs out of the salt container onto the base of the washing com partment This is not a cause for concern the water will be pumped out at the start of the next wash programme 5 Clean any salt remnants on the container open ing 6 Turn the lid clockwise to the stop otherwise spe cial salt will leak into the wash water this could lead to poo
13. cal COANECION s sereia a a a sd aided an a add aa t hei od a a Bea A 32 Connections 25 5 245 satel peer hen ri ck incl ott Eee ene ie eh cies BI os ie GA a n i 33 Guarantee Conditions caia A Malet Rhea ca ann Baden Ir Die hed ot 34 Service and Spare Parts aia pesci eaten oe ale Berets PEW OE ee EE ae wa Ewa eek A 35 A Safety Instructions The safety aspects of ELECTROLUX electrical appli ances comply with accepted technical standards and the German Appliance Safety Law Nevertheless as a manufacturer we consider it our obligation to make you aware of the following safety information Installation Connection and Plac ing into Operation e The dishwasher may only be transported upright e Check the dishwasher for transport damage Do not in any circumstances connect an appliance that is damaged In the case of damage please contact your supplier e Prior to placing the appliance in operation ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate e For information on how to correctly install and connect up your dishwasher please read the Installation section Multiway plugs connectors and extension cables must not be used This could constitute a safety hazard Child Safety e Children often do not recognise the hazards asso ciated with the use of electrical appliances It is th
14. ce Force Centre Once the fault has been rectified press the On e f other lights in the multidisplay flash please Off button The wash programme will continue If contact Service Force and let them know which fault indicator is flashing Symptom Possible Cause Solution The top light in the Tap is blocked or furred with lime scale Clean tap paulicieplay 1 Masma The filter where present in the threaded Clean the filter in the threaded hose hose fitting is blocked fitting O O The water inlet hose is connected There is no water wrongly entering the dishwasher Check hose installation The middle light is flashing The sink outlet is blocked Clean the sink outlet in the multidisplay O F F ji The water drain hose is connected Check hose installation wrongly O The top and the middle light are flashing in the multidisplay The anti flood system has been triggered See ihe TAP aie GONAGE eed Force O O 22 there are problems operating the dishwasher The dishwasher door has not been closed properly Shut the door The programme does The mains plug is not plugged in Insert mains plug not start House fuse is faulty Replace fuse For dishwasher models with delay start timer Delay start has been selected If dishes are to be washed immediately cancel delay start timer The washing compartment is made of anti Onl
15. d tight only In order that access to the tap in the kitchen Gi is not limited by the use of the dishwasher we recommend the installation of an addi tional tap or fitting a two way adapter to the existing tap e If you need a longer water inlet hose than that supplied VDE approved complete hose sets are to be used These are available from your local Service Force Centre 29 The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water and the draining pump in the dishwasher is switched on 30 Please take care when installing the water inlet hose The distance between the bottom edge of the safety value and the floor on which the dish washer is standing must be at least 30 cm The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water inlet hose or the safety valve in water If the water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by a specialist or Customer Serv ices Place the water inlet hose in
16. door 1 If the lid is closed press release button 1 The lid springs open 2 Fill the detergent dispenser with detergent The markings indicate the dosing levels 20 corresponds to approx 20 ml of detergent 30 corresponds to approx 30 ml of detergent 3 Close the lid and press until it locks into place O If the dishes are very heavily soiled put addi tional detergent into the adjacent chamber 2 This detergent will take effect during the pre wash 17 Use of 3 in 1 Combi Detergent Tablets General Advice These products are tablets with combined detergent rinse aid and salt functions 1 Before using these products you should first check that the water hardness in your supply is compati ble with the use of these products as per the detergent manufacturers instructions on the prod uct packaging 2 These products should be strictly used according to the detergent manufacturers instructions Do not place the tablets in the tub or the A cutlery basket as this will result in poorer wash results The tablets should be pla ced in the detergent dispenser 3 If you encounter problems when using 3 ini products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special Advice When using combination products the rinse aid and salt lights are no longer useful It may be help
17. eason proceed as described below The wires on the mains lead are coloured in accord ance with the following code Green and Yellow Earth Blue Neutral Brown Live e The wire coloured green and yellow must be con nected to the terminal marked with the letter E or by the earth symbol or coloured green and yel low e The wire coloured blue must be connected to the terminal N or coloured black e The wire coloured brown must be connected to the terminal marked L or coloured red e Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath A WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that if it is necessary to cut off the plug it is disposed of safely and not retained 32 Green amp Yellow Cord Clamp Connections The water inlet and drain hoses as well as the mains cable must be connected beside the dishwasher because there is no space for them behind the appli ance The example plumbing and electrical installation given below can only be regarded as a recommenda tion the actual situation where the dishwasher is to be installed will define the exact installation available connections local electricity and water board regula tions for connecting up appliances etc Two 45 or Straight Connec tions Outer 19 mm Length 30 mm Double Water drain
18. er authorised by ELECTRO LUX Never unplug the appliance by pulling on the cable always pull the plug Additions or modifications to the dishwasher are not permitted for safety reasons Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Sharp knives and items of cutlery with sharp edges must be placed in the cutlery tray or in the upper basket Correct Use Only wash household dishes using the dish washer If the appliance is used for other pur poses or is used incorrectly the manufacturer cannot accept any liability for any damage caused Prior to use ensure that the manufacturers of the special salt detergent and rinse aid employed specifically permit the usage of their products in household dishwashers Do not put any solvents in the dishwasher There is a risk of an explosion The anti flood system provides dependable pro tection against damage due to leaks For this sys tem to function correctly the following preconditions must be met The appliance must remain connected to the mains even when it is switched off The dishwasher must be correctly installed Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods e g when you are away on hol iday Do not sit or stand on the open door the appli ance may tip over
19. erefore important that you ensure children are adequately supervised and that you do not allow children to play with the dishwasher there is a risk that children can shut themselves inside the appliance risk of suffocation e Packaging materials e g films styrofoam can be dangerous for children Risk of suffocation Keep packaging away from children e Detergents can cause burns to the eyes mouth and throat or even cause choking Please observe the manufacturer s safety instructions for cleaners and detergents e The water in your dishwasher is not suitable for drinking If there are still remnants of detergent in the appliance there is a risk of burns e When disposing of the dishwasher unplug from the mains cut off and dispose of the mains cable Break the door lock so that the door no longer shuts General Safety e Repairs to the dishwasher are only to be carried out by qualified service engineers Improper repairs can give rise to significant hazards for the user If your appliance needs repairing please contact customer service or your dealer Never place the dishwasher in operation if the mains cable water inlet or drain hose is damaged or the control panel work top or plinth area is damaged such that the inside of the appliance is freely accessible If the mains lead is damaged or is to be replaced for a longer lead the cable obtainable from ELECTROLUX Service Force must be changed by a service engine
20. ful therefore to switch the rinse aid off please note that only some dishwashers have this facility and select ing the lowest possible setting for water hardness For more information please refer to your instruction manual If you decide to switch to the use of a standard deter gent system we advise that you e Refill both the salt and rinse aid compartments e Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load e Readjust the waterhardness setting again accord ing to the conditions for your region as per the instruction manual 18 Concentrated Detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caus tic components low alkaline concentrated detergents with natural enzymes Y The use of 50 C wash programmes in con junction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are spe cially matched to the dirt dissolving proper ties of the enzymes in the concentrated detergent For this reason 50 C wash pro grammes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C programmes Detergent Tablets G Detergent tablets of different makes dis solve at different speeds For this reason some detergent tablets cannot develop their
21. full cleaning power during short pro grammes Therefore please use wash pro grammes with pre wash when using detergent tablets Selecting the Wash Programme Programme Table Choose the most suitable wash programme with the aid of this table Type of Dishes Dinner service and Pans Dishes without Pans in addition with dishes that are sensitive to changes in tem perature Type of normal soiling Formal normal dishes that have just been Soiling dried onleft overs soiling soiling mi normal to slight soil particularly suitable when concentrated detergents are used Suitable Wash Pro y y y y gramme Press pro gramme but 2 2 3 E S v5 4 ton 65 50 5 Programme Pre wash Pre wash Sequence 1 Main wash Main wash Main wash Main wash 2 rinsing Rinsing Rinsing 7 Final rinse Final rinse Final rinse Final rinse Drying Drying Drying Consumption SARTE g g 3 g Figures Duration 105 115 minutes 120 130 minutes 75 85 minutes 30 minutes Energy 1 75 1 95 kWh 0 95 1 05 kWh 1 05 1 24 kWh 0 8 kWh Water 16 18 litres 14 16 litres 10 12 litres 8 liter 1 The various stages in the wash programme have different sounds because the dishes are washed more intensely for short periods during certain stages of the wash programme to improve cleaning 2 The consumption figures were determined under standard conditions They are intended as a guide only and depend on the loading Va
22. ip Depending on type the dishwasher is to be installed as follows Dishwashers That Can Be Inte grated see installation template supplied The door of the appliance can be fitted with a wooden furniture door with the following dimensions Width 591 594 mm Thickness 16 24 mm Height dependent on variable Recess height Plinth height The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining units must be measured at the place of installation If the facing panel is longer than 600 mm the door of the appliance cannot be opened completely the facing panel bumps against the plinth If this is the case the plinth must be cut out see installation template or the brace adapter for the extra long door BLT 60 must be used You can obtain this with the E No 911 239 008 27 Built In Dishwasher see enclosed installation instructions Free Standing Appliances A can be set up as stand alone without addi tional installation If the dishwasher is set up next to a cooker a heat insulating non flammable plate must be mounted between the dishwasher and the cooker flush to the top edge of the work sur face depth 57 5 cm The plate should have aluminium foil on the side facing the cooker If the dishwasher is installed underneath a kitchen work surface the original work surface of the dish washer is to be removed as follo
23. ith Special Salt for the Water Softener 3 Filling with Rinse Aid Adjusting the Water Softener To prevent the build up of scale on dishes and in the dishwasher the dishes must be washed with soft i e low lime content water For this reason the dish washer is fitted with a water softener in which tap water from a hardness of 4 d German degree is softened with the aid of special salt Your local water authority can advise you on G the hardness of the water in the area where you live The water softener can be set manually using the water hardness switch it can also be set electroni cally using the buttons on the control panel Water Hardness Hardness Setting Number of in d ininPPM Range Manual Electronic Plasngs 41 50 730 900 IV 5 5 30 40 530 720 IV 4 4 19 29 330 520 IHV 3 3 4 18 70 320 1 11 111 2 2 1 less than 4 less than 70 l no salt necessary 1 1 d German degree measure of the hardness of water 2 PPM Parts Per Million international units of water hardness factory setting Adjust the water softener to the setting given in the table that corresponds to the hardness of the water in the area where you live A It is only possible to adjust the water hard ness setting when there is no programme running lf you have inadvertently started a programme an LED indicator is constantly illuminated then the programme must be cancelled by pres
24. m comprises a coarse fine filter microfilter and a flat filter Unlock the fil ter system using the handle on the microfilter and remove Turn the handle about Y a turn anticlockwise and remove Take hold of the coarse fine filter 1 by the handle with the hole and remove from the microfilter 2 Clean all filters thoroughly under running water Remove the flat filter 3 from the base of the washing compartment and clean both faces thor oughly Put the flat filter back in the base of the washing compartment Place the coarse fine filter in the microfilter and press together Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not pro trude above the base of the washing compart ment A Under no circumstances may the dishwasher be used without filters 21 What to do if Try to rectify minor faults on the dishwasher with the aid of the instructions given here If you call in cus tomer service to resolve one of the malfunctions listed here or rectify an error made in the operation of the appliance the customer service engineer s visit is not free of charge even during the period of guar antee Fault warnings are displayed e If the top or middle light in the display is flashing the fault is displayed again contact your local you can probably rectify the fault yourself Servi
25. ning of the dishes It is for this reason that the noise level changes during the wash pro gramme Contents Safety Instructions 4 i 4 cccn E bed David Red eae iad Mende eae ede ated AE 5 Disposal siii ci Gene blast Whi beet nea ie den hate Se he Pia Sm oo E 6 Economical and Ecological Dishwashing 0 cece ete 6 Appliance Features and Control Panel 20 0 cee tee teas 7 A ANE sh Actes cei ON 8 Prior to using for the first time 0 00 00 e eee 8 Adjusting the Water Softener 0 0 tte tee eee 9 Filling with Special Salt for the Water Softener 0 0 teed 11 Filling with RMSEA ios aaa a beds EA a da 12 Adjusting Rinse Aid Dosing 3 04 2 4 nta rele be bene al ea ae dd ee aa bays 12 In Dally Use ico ii Ving baht et Sn ais eds a oad ee 13 Loading cutlery and dishes oooooocorocor ete eee 13 Loading Cullen A e mae acateeh 4 14 Loading Pans Frying Pans and Large Plates 0 cece ete eae 15 Loading Cups Glasses and Coffee Services 00 cect eens 16 Adjusting the Height of the Upper Basket 0 0 0 0 cee tte teens 16 Filling with Detergent cios yen ede ees bey eed eee A e hoe nad wy oar ob aaa 17 Use of 3 in 1 Combi Detergent Tablets 0 0 0 cca 18 Concentrated Detergent s so re aaea EE aa ATE EAEE E eet eee 18 Selecting the Wash Programme Programme Table 0 0 00 cece eae 19 Start the wash programme 20 Inter
26. not tempera Glazed patterns may fade if machine washed fre ture resistant quently Bonded cutlery items or dishes Silver and aluminium parts have a tendency to dis Pewter or copper items colour during washing Left overs e g egg white Lead crystal glass egg yolk and mustard often cause discolouring and Steel items subject to rusting staining on silver Therefore always clean left overs Wooden platters from silver immediately if it is not to be washed Items made from synthetic fibres straight after use Some types of glass can become dull after a large number of washes e Before loading the dishes you should Remove large left overs Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rota tion of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Do not lay small objects e g lids in the cutlery basket 13 Loading Cutlery A A A Long bladed knives stored in an upright posi tion are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizon tally in the upper basket Take care when loading or unloading sharp
27. nsumer advisor 23 Technical Data Capacity 12 place settings including serving dishes Permitted Water Pressure 1 10 bar 10 100 N cm 0 1 1 0 MPa Electrical Connection Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right Dishwasher Free Standing Appliances Dimensions 850 x 600 x 600 H x B x Din mm Max Weight 54 Kg Dishwashers that Can Be Integrated Built In Dishwashers Dimensions 820 880 x 596 x 570 H x W x D in mm Max Weight 50 Kg Dishwashers that Can Be Fully Integrated Dimensions 820 880 x 596 x 546 550 H x W x D in mm Max Weight 50 Kg This appliance conforms with the following EU Directives e 73 23 EWG dated 19 02 1973 Low Voltage Directive e 89 336 EWG dated 03 05 1989 including Directive Amendment 92 31 EWG EMC Directive 24 Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test pro gramme see Programme Table Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Programme Table Full Load Half Load 12 place settings incl serving dishes 6 place settings incl serving dishes leaving alternate positions free Detergent D
28. osing 5g 25g Type B 20g Type B Rinse Aid Setting 4 Type III 4 Type Ill Sample loading arrangement Upper basket A T E Us NS TAK I I Sample loading arrangement Upper basket Sample loading arrangement Lower basket ADN Y yA A CZ w SS 3 TCM 25 Sample loading arrangement Cutlery basket Some dishwasher models have cutlery baskets with out a grid insert 26 INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher e The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level e To compensate for unevenness in the floor and to match the height of the appliance to that of sur rounding units extend the threaded feet by unscrewing use a screwdriver e For built in integrated and fully integrated dish washers the rear feet should be adjusted from the front of the appliance using a screwdriver e The drain hose inlet hose and mains cable must not be kinked or crushed when the dishwasher is in position e The dishwasher must also be screwed on tightly to the work surface or to the adjoining units This is essential to ensure the diswasher does not t
29. r wash results To avoid this run a rinse programme after filling the salt container with spe cial salt This will wash away salt water and any salt crystals that have been spilt Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and the special salt indicator Ng to extinguish The setting of the water softener and thus the consumption of salt are dependent on the hardness of the local water Filling with Rinse Aid Rinse aid ensures that your dishes gleam and are free from spots and that you glasses are clear Use only branded rinse aid for dishwashers Never fill the rinse aid container with any another substance e g concentrated vine gar This would damage the appliance Fill with rinse aid e Prior to using the dishwasher for the first time When a dark point surrounded by a light ring is to be seen in the indicator window on the container If there is rinse aid in the container the indicator window is uniformly dark The rinse aid compartment is on the inside of the dishwasher door 1 Open the door 2 Press the rinse aid compartment release button with your finger 3 Fully open the rinse aid compartment lid 4 Fill with rinse aid exactly up to the level marked max this corresponds to a quantity of approx 140 ml 5 Close the lid and press until it locks into place 6 Wipe up any spilt rinse aid with a cloth Otherwise
30. riations can occur during normal usage 3 4 Test programme This programme is not suitable when left overs have dried on 19 Start the wash programme 1 Check that when the dishes and cutlery are loaded in the dishwasher the spray arms are free to rotate 2 Open the tap fully Shut the door 4 Press the On Off button The On Off button indica tor lights up 5 Press the programme button for the required pro gramme see Programme Table The pro gramme indicator lights up One or two lights will flash in the multidisplay During this time it is pos sible to reselect the programme The selected wash programme will start after about 6 seconds The current wash programme stage will always be shown in the multidisplay w Gi If the top light and or the middle light in the multidisplay flash after the programme has started please read the section What to do if Interrupting or ending the wash programme 1 Only interrupt a wash programme that is run ning if it is absolutely necessary After the appliance has been closed again the air that has entered will be greatly heated and expand As a result water may penetrate the base of the appliance and trigger the anti flood system Interrupt the wash programme by open ing the door Hot steam can escape from the appliance when the door is opened deleted by the reviewer Open the door carefully 1 Open the door of the dishwasher The wa
31. rupting or ending the wash programme 0 tees 20 Pause TUNCUON ici A cake be E E a E dae ages 20 Load SENSING serut kaa 29 4 Hawtin oleh oe Se awed a A Oh he aces 20 Switching Off the Dishwasher 0 0 00 ii en ea a ete eee 20 Care and CI ANIOS AA OM RA Pe GOA e 21 Cleaning the Filter udooiioc add ds a id se RA a ida ai 21 Whatta d Ti it a pa ans pata lb Mens eee ad pee pee 22 Fault warnings are displayed dre errer ki e EE tee 22 there are problems operating the dishwasher o ococccooccoccocoo eee 23 the wash results are unsatisfactory 2 0 2 tet 23 Technical Data Telani te ps bh te BR gee He ae de Deals Sede ete tm ed a 24 Notes Tor TLestilMStitutes vota A a Re aoe ea a nee 25 Contents Installation and Connection Instructions 0 0 00 0000 ee eee ees 27 Installing the Dishwasher piai 548 6 ia oe Means be dda pe dale had ed ee baer ied de 27 Dishwashers That Can Be Integrated 0 0 2c tee eae 27 Built In DiShWaSNER 20 cee A aes oem eet td es Deere Seeds A 28 Free Standing Appliances oooooocoooo tnt ae 28 Connecting the Dishwasher 0 cette eee 29 Water Connection tsetse A o ght Oa sek lege das 29 Permitted Water pressure o 29 Connect the inlet ROSE iisa ss Daria barri lt Beds By it la a te ch dealt ama Weep 29 Water Cialis a IN cep Ue Se Saat on dy a aloes Ir DAA bres 31 Leak Prevention System zye ierosme au Anki EEA E E ERa eee eee 31 Electri
32. sh pro gramme will stop 2 Lights are flashing in the multidisplay 3 Shut the door The wash programme continues Ending the wash programme 1 Press the button for the wash programme that is running and hold it down until the programme indi cator for the wash programme goes out 2 Release the programme button the wash pro gramme has been ended Pause function The pause function can only be initiated before the drying section of the programme If the pause function is initiated during the drying section of the programme the wash programme is ended 20 Using the pause function the dishwasher can be tem porarily stopped 1 Press the On Off button The wash programme will stop 2 All indicators will go out 3 When after a short time the wash programme is to continue press the On Off button again The wash programme will continue Y The wash programme should not be stopped for a prolonged period or the cooled water will need to be reheated resulting in increased energy consumption Load Sensing If a wash programme is started even though there are only a few dishes in the upper and or lower basket an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes By this means it is possible to wash only a few dishes quickly and economically At half load 6 place settings up to 2 litres of water and 0 2 kWh of electricity are saved Switching
33. sing the appropriate button 1 The dishwasher must be switched off Manual setting Open the door on the dishwasher Remove the lower basket from the dishwasher Turn the water hardness switch to 0 or 1 Re position the lower basket Electronic setting Press the water softener and function buttons simultaneously and keep them pressed In addition press the ON OFF button 8 The LED indicator for the water softener button flashes 9 Press the water softener button again The LED indicator for the water softener button will be illuminated continuously for an initial 5 seconds and then begin to flash The number of flashes corresponds to the hardness setting The sequence of flashes is repeated several times after a 5 second pause 10 Each time you press the water softener button the hardness setting will go up by 1 Exception Hardness setting 1 follows hardness setting 5 N oa E gt E o N If the hardness setting is changed the LED indicator for the water softener button will con firm the change by remaining illuminated con tinuously for 5 seconds and then flashing again The number of flashes corresponds to the new hardness setting The sequence of flashes is repeated several times after a 5 second pause 11 Once the hardness setting is correct press the ON OFF switch The hardness setting is then saved 10 Filling with Special S
34. such a way that it is never higher than the bottom edge of the safety valve Water drain Drain hose The drain hose must not be kinked crushed or entangled e Connecting the drain hose Maximum permitted height 1 metre Minimum required height 40cm above the lower edge of the machine Extension hoses e Extension hoses are available from your dealer or customer service The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded e Extension hoses may be laid a maximum of 3 metres horizontally the maximum permitted height for the connection for the drain hose is then 85 cm Siphon connection e The outlet of the drain hose a 19 mm fits all com monly available siphon types The outer diameter of the siphon connection must be at least 15 mm e The drain hose must be fixed to the siphon con nection using the hose clamp supplied If the dishwasher is fitted at a high position If the dishwasher is installed at a high level and the drainhose connection is less than 30 cm from the bot tom of the appliance adapter kit ET 111099520 must be fitted This is available from Customer Service Water drain into wash basins only possi ble with free standing appliances In the case that you wish to hang the drain hose in a wash basin use a detachable hose elbow You can obtain this from customer service under spare part number ET 646 069 190
35. washing water can reach all items e The cup racks can be folded up out of the way for tall items e Lay or hang wine champagne and brandy glasses in the cut outs on the cup racks J a e Glasses beakers etc can also be placed on the two rows of prongs on the left of the upper basket L Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket With upper basket raised 22 cm 30 cm With upper basket lowered 24 cm 29 cm O The height of the basket can also be adjusted when it is loaded Lowering the Upper Basket 1 Pull the upper basket out completely 2 Holding the upper basket by the handle lift it as far as it will go and then lower it vertically The upper basket will engage in the lower position Raising the Upper Basket 1 Pull the upper basket out completely 2 Holding the upper basket by the handle lift it as far as it will go and then lower it vertically The upper basket will engage in the higher position 16 Filling with Detergent N Only use dishwasher detergent Fill with detergent Prior to the start of a wash programme not for the pre wash programme The detergent is released into the wash water during the programme Y Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging The detergent compartment is on the inside of the dishwasher
36. ws 1 Unscrew the screws from the positioning plates on the back 1 2 Slide the appliance s work surface approx 1 cm to the rear 2 3 Lift the work surface at the front 3 and remove If the dishwasher is later used as a free standing appliance the original work surface must be re mounted za O The plinth on free standing appliances is not adjustable 28 Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that pre vent the wash water returning into the drinking water system and comply with the applicable plumbing reg ulations e The dishwasher can be connected to cold and hot water supplies up to max 60 C e The dishwasher must not be connected to open hot water appliances or instantaneous water heat ers Permitted water pressure Lowest permitted water pressure Consult your installer if the water pressure is less than 1 bar 1 bar 10 N cm 100 kPa y P Highest permitted water pressure In the case of a water pressure greater than 10 bar a pressure reduc 10 bar 100 N cm 1 MPa tion valve must be used available from your dealer Connect the inlet hose i The water inlet hose must not be kinked crushed or entangled when it is being con nected up Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch Tighten the threaded hose fitting han
37. y wash cutlery and dishes that are corrosive stainless steel Any spots of rust Spots of rust are visible inside the washing compartment stem from suitable for dishwasher use in the washing compart other sources flakes of rust from the water ment pipe or from pans cutlery etc Remove Close the salt dispenser lid securely such spots with a commercially available stainless steel cleaner There is a whistling noise during washing The whistling is not a cause for concern Use a different brand of detergent the wash results are unsatisfactory The dishes are still dirty The wrong wash programme was selected e The dishes were arranged in such a way as to stop the water reaching all parts of the surface The dish racks must not be overloaded e The filters in the base of the washing compart ment are dirty or incorrectly positioned e Too little or no detergent was used e Where there are limescale deposits on the dishes The salt dispenser is empty or the water softener unit is set wrongly e The drain hose is incorrectly connected The dishes are wet and dull e Rinse aid was not used e The rinse aid container is empty There are streaks milky spots or a bluish coating on glasses and dishes e Decrease rinse aid dosing There are dried water drops on the glasses and dishes e Increase rinse aid dosing e The detergent may be the cause Contact the detergent manufacturer s co
Download Pdf Manuals
Related Search