Electrolux ESF2450 User's Manual
Contents
1. 2 During the Auto washing programme the level of soiling on the dishes is determined by how cloudy the water is The programme duration water and energy consumption levels can vary this depends upon if the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled The temperature of the water is automatically adjusted between 45 C and 70 C 3 Test programme for test institutes Please refer to separate leaflet supplied for test data Consumption values Programme Programme duration Energy consumption Water consumption tai in kWh in litres 5 7 1 0 9 0 AUTO 0 5 0 8 5 0 9 0 ECO 0 68 7 0 Ci 0 45 6 0 1 The digital display shows the programme duration The pressure and temperature of the and the quantity of dishes can change water the variations of power supply these values Setting and starting a washing programme Set the washing programme with the The washing programme starts auto door ajar The washing programme only matically starts after you close the door Until then The phase indicator light for the wash it is possible to modify the settings ing programme is on Do these steps to set and start a washing i When the washing programme oper programme ates you cannot change the pro 1 Switch on the appliance gramme Cancel the washing pro 2 Make sure that the appliance is in setting gramme mode Warning Only interrupt or cancel a 3 Press one of the programm2. dishes can be wet once the programme finish ed We recommend to leave the appli ance door ajar so that dishes can dry naturally Standby mode If you do not switch off the appliance at the end of the washing programme the appli ance automatically goes into standby mode The standby mode decreases energy con sumption Three minutes after the end of the pro gramme all indicator lights go off and the digital display shows one horizontal bar Press one of the buttons not the on off but ton to go back to end of programme mode unsatisfactory washing results and damage to the appliance The dishwasher has 2 filters 1 microfilter 2 flat filter 12 electrolux Do these steps to clean the filters 1 Open the door 2 Remove the basket 3 Remove the filters in the bottom of the appliance Clean the filters below running water Put the filters back Turn the microfilter clockwise to lock it Close the door NOOK Cleaning the spray arm Regularly examine the spray arm Remove remaining food from the holes in the spray arm Technical data Dimensions Width cm Height cm Depth cm Electrical connection Voltage Overall power Fuse Water supply pressure Minimum Maximum Capacity Place settings What to do if The appliance does not start or stops during operation If there is a fault first try to find a solution to the problem yourself If you cannot find
3. buttons Save energy button Saver Delay start button Indicator lights Digital display Function buttons Indicator lights TA The indicator light comes on when the washing phase or the rinsing phase operates JS The indicator light comes on when the drying phase operates gt The indicator light comes on when the washing programme is completed tS The indicator light comes on when it is necessary 1 to fill the salt container Refer to the chapter Use of dishwasher salt The salt indicator light can stay on for some hours but it does not have an unwanted effect on the operation of the appliance electrolux 5 Indicator lights The indicator light comes on when it is necessary to fill the rinse aid Refer to the chapter Use of rinse aid 1 The indicator light is off when a washing programme operates Delay start button Use the delay start button to delay the start of the washing programme with an interval between 1 and 19 hours Refer to the chapter Setting and starting a washing programme Digital display The display shows e Adjusted level of the water softener e Programme duration e Remaining time to the end of the pro gramme e End of a washing programme e Number of hours in delay start e Fault codes Save energy button This function decreases the temperature in the drying phase Saved energy is between 10 and 25 If dishes at the end of the programme are w
4. close the water tap e Only an authorised service engineer can repair this appliance Use only original spare parts Setting and starting a washing programme 10 Care and cleaning 11 Technical data 12 What to do if 12 Installation 14 Water connection 14 Electrical connection 16 Environment concerns 16 Subject to change without notice e Do not do repairs yourself to prevent injury and damage to the appliance Always con tact your local Service Force Centre General safety e Persons including children with reduced physical sensory mental capabilities or lack of experience and knowledge must not use the appliance They must have su pervision or instruction for the operation of the appliance by a person responsible for their safety e Obey the safety instructions from the man ufacturer of the dishwasher detergent to prevent burns to eyes mouth and throat e Do not drink the water from the dishwash er Detergent residues can stay in your ap pliance e Always close the door when you do not use the appliance to prevent injury and not to stumble over the open door e Do not sit or stand on the open door Child safety e Only adults can use this appliance Chil dren must get supervision to make sure that they do not play with the appliance e Keep all the packaging away from children There is a risk of suffocation e Keep all detergents in a safe area Do not let children touch the detergents e Keep childre
5. hollow items e g cups glasses and pans with the opening down Make sure that water does not collect in the container or in a deep base Make sure that cutlery and dishes do not lie inside one another Make sure that cutlery and dishes do not cover other cutlery and dishes Make sure that glasses do not touch other glasses Put small objects in the cutlery basket e Plastic items and pans with non stick coatings can keep water droplets e Plastic items do not dry as well as porce lain and steel items e Put light items in the main basket Make sure that the items do not move Caution Make sure that the spray arm can move freely before you start a washing programme Primary basket Arrange the deep dishes and large lids around the edge of the basket Arrange items on and below the cup racks The water must come to all parts of the dishes You can fold the cup racks to clean high items CA ANAE CES i 1 YW Use of detergent Cutlery basket Warning Do not put long bladed knives in a vertical position to prevent injury Arrange long and or sharp items of cutlery horizontally in the primary basket Be careful with sharp items such as knives Use the cutlery basket for e Forks and spoons with the handles down e Knives with the handles up The cutlery basket has a cutlery grid that you can remove Do not let the cutlery bond together Make sure that the spray arm c
6. installed e The quantity of detergent is too little or missing Limescales particles on the e The salt container is empty dishes e The water softener is adjusted on a wrong level e The salt container cap is not closed correctly The dishes are wet and dull e No rinse aid has been used e The rinse aid dispenser is empty There are streaks milky spots Decrease the rinse aid dosage or a bluish coating on glasses and dishes 14 electrolux The cleaning results are not satisfactory Dry water drop signs on glasses and dishes Installation e Increase rinse aid dosage e The detergent can be the cause Warning Make sure that mains plug is disconnected from the mains socket during installation Fitting the appliance Put the appliance adjacent to a water tap and a drain When you put the appliance in place make sure that the water hoses are not kinked or squashed Install the appliance on a kitchen sink work top or built in Positioning Install the dishwasher into the furniture of the kitchen Water connection Make sure that the dimensions of the recess agree with the given dimensions Make sure that there are openings in the fur niture for the inlet hose the water drain hose and the mains cable Adjusting the level of the appliance Make sure that the appliance is level to close and seal the door correctly If the level of the appliance is correct the door does not catch on t
7. the rinse aid dispenser Loading cutlery and dishes Helpful hints and tips Caution Only use the appliance for household utensils that are applicable for dishwashers Do not use the appliance to clean objects that can absorb water sponges household cloths etc electrolux 7 When you set the water softener to level 1 the salt indicator light does not stay on 1 Press the release button A to open the rinse aid dispenser 2 Fill the rinse aid dispenser with rinse aid The mark max shows the maximum level 3 Remove the spilled rinse aid with an ab sorbent cloth to prevent too much foam during the subsequent washing pro gramme 4 Close the rinse aid dispenser i The capacity of the rinse aid dispenser is approximately 150 ml The quantity of rinse aid is sufficient for approximately 60 washing programmes Adjust the dosage of rinse aid The appliance is set at the factory at level 1 You can set the rinse aid dosage between 1 6 1 6 ml of the rinse aid Refer to the washing results chapter What to do if Start with the lowest dosage 1 Turn the arrow clockwise to increase the dosage 2 Increase the dosage if there are water droplets or limescale on the dishes e Before you load cutlery and dishes do these steps Remove all food remainings and debris Make burnt remaining food in pans soft 8 electrolux e While you load cutlery and dishes do these steps Load
8. washing programme starts auto matically Do not open the door during the count down to prevent interruption of the countdown When you close the door again the countdown continues from the point of interruption Cancelling a delay start 1 Press and hold function buttons B and C until all the programme lights come on When you cancel a delay start you also cancel the washing programme 2 Set anew washing programme Care and cleaning Warning Switch the appliance off before you clean the filters Cleaning the filters Caution Do not use the appliance without filters Make sure that the installation of the filters is correct Incorrect installation will cause electrolux 11 i You can select the washing programme and delay start also with the door closed When you press a programme button you have only 3 seconds to select a dif ferent washing programme or a delay start After these 3 seconds the selec ted programme starts automatically End of the washing programme Switch off the appliance in these conditions e The appliance stops automatically e The display shows 0 e The end of programme indicator light comes on 1 Press the on off button 2 Open the door 8 For better drying results keep the door ajar for some minutes before you remove the dishes Let the dishes cool down before you remove them from the appliance Hot dishes are easily damaged i If the save energy function is set
9. Thinking oF yor_ user manual Electrolux Dishwasher ESF2450 2 electrolux Electrolux Thinking of you Share more of our thinking at www electrolux com Contents Safety information Product description Control panel Use of the appliance Setting the water softener Use of dishwasher salt Use of rinse aid Loading cutlery and dishes Use of detergent Washing programmes CE AN Safety information i For your safety and correct operation of the appliance read this manual carefully before installation and use Always keep these instructions with the appliance even if you move or sell it Users must fully know the operation and safety fea tures of the appliance OONN O O1 O1 R ND Correct use e The appliance is designed exclusively for domestic use e Only use the appliance to clean household utensils that are applicable for dishwash ers e Do not put solvents in the appliance Risk of explosion e Put the knives and all items with sharp points in the cutlery basket with their points down If not put in a horizontal po sition in the main basket e Use only branded products for dishwash ers detergent salt rinse aid e If you open the door while the appliance is in operation hot steam can escape Risk of skin burns e Donot remove dishes from the dishwasher before the end of the washing programme e When the washing programme is comple ted disconnect the mains plug from the mains socket and
10. a sol Do these steps to remove the spray arm 1 Turn the nut anticlockwise 2 Remove the spray arm 3 Fully clean the holes External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth Only use neutral detergents Do not use abrasive products scouring pads or solvents acetone trichloroethylene etc Frost precautions Caution Do not install the appliance where the temperature is below O C The manufacturer is not responsible for damage because of frost If not possible empty the appliance and close the door Disconnect the water inlet hose and remove water from the water inlet hose 54 5 44 7 48 49 Information on the electrical connection is given on the rating plate on the back of appliance 0 8 bar 0 08 MPa 10 bar 1 0 MPa 6 ution to the problem yourself contact the Service Force Centre electrolux 13 Fault code and malfunction Possible cause and solution e digital display shows I 0 The dishwasher does not fill with wa ter digital display shows cL The dishwasher will not drain e the drain pump operates continu ously e all indicators lights on the control panel go off The anti flood device operates The programme does not start The water tap is blocked or furred with limescale Clean the water tap The water tap is closed Open the water tap The filter in the water inlet hose is blocked Clean the filter The conn
11. aining water out of the dish washer Warning Only if the dishwasher is connected to the mains socket the water safety system operates when the dishwasher is off electrolux 15 2 procedures are possible to install the water drain hose 1 Attach the plastic curve supplied at the end of the hose Put the water drain hose in the sink 2 Connect the water drain hose to the wa ter drain system The hose must be less than 75 cm above the bottom of the dishwasher to prevent incorrect operation of appliance If you connect the water drain hose to a trap spigot under the sink remove the plastic membrane A If you do not remove the membrane remaining food can cause a blockage in the drain hose spigot _A 16 electrolux Electrical connection A Warning The manufacturer is not responsible if you do not follow these safety precautions Ground the appliance according to safe ty precautions Make sure that the rated voltage and type of power on the rating plate agree with the voltage and the power of the lo cal power supply Always use a correctly installed shock proof socket Environment concerns The symbol X on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will
12. an move freely before you close the door i Only use detergents powder liquid or tablet that are applicable for dishwash ers Follow the data on the packaging e Dosage recommended by the manu facturer e Storage recommendations The instructions on the packaging usu ally refer to large dishwashers 12 set tings Do not use more than the correct quan tity of detergent to save an environment Fill with detergent Do these steps to fill the detergent dispenser 1 Open the lid of the detergent dispenser 2 Fill the detergent dispenser A with de tergent 3 If you use a washing programme with prewash phase put more detergent in the prewash detergent compartment B The detergent is removed during the pre wash phase 4 Close the lid of the detergent dispenser Use of detergent tablets Put the detergent tablet in the detergent dis penser A Detergent tablets contain e detergent e rinse aid e other cleaning agents Do these steps to use detergent tablets Washing programmes Washing programmes electrolux 9 1 Make sure that the detergent tablets are applicable for your water hardness Refer to the instructions from the manufacturer 2 Set the lowest levels of water hardness and rinse aid dosage It is not necessary to fill the salt container and the rinse aid dispenser Do these steps when the drying results are not satisfactory 1 Fill the rinse aid dispenser with rinse ai
13. d 2 Set the rinse aid dosage to position 2 Do these steps to use the detergent powder again 1 Fill the salt container and the rinse aid dispenser 2 Setthe water softener to the highest level 3 Do a washing programme without dishes 4 Adjust the water softener Refer to the chapter Setting the water softener 5 Adjust the rinse aid dosage i Different brands of detergent dissolve in different times Some detergent tablets do not have the best cleaning results during short washing programmes Use long washing programmes when you use detergent tablets to fully remove the detergent Programme pede ne Programme description Prewash Selectable ba por Main wash up to 70 C impact on B S Y ais ne 2 intermediate rinses washing p ne Final rinse pro j Drying gramme s Prewash Selectable AUTO ni Hee Main wash up to 45 C or 70 C impact on 2 and light pots a 1 or 2 intermediate rinses washing Final rinse pro soil pate Drying gramme Prewash Selectable Crockery Main wash up to 55 C impact on E c o jus and cut 1 intermediate rinse washing lery Final rinse pro Drying gramme 10 electrolux Programme Degree Type of Programme description of soil load Selectable Normal Crockery Main wash up to 50 C no impact or light and cut 1 intermediate rinse on washing soil lery Final rinse pro gramme 1 For programmes where the option has an impact the energy saving is between 10 and 25
14. e buttons washing programme if necessary Refer to the chapter Washing pro grammes Caution Open the door carefully Hot The programme indicator light comes steam can come free on All other programme indicator lights go Cancelling a washing programme off 1 Press and hold function buttons B and C The digital display shows in flashing the until all the programme lights come on programme duration 2 Release function buttons B and C to can The phase indicator light for the wash cel the washing programme ing programme starts to flash At this time you can do these steps 4 Close the door 1 Switch off the appliance 2 Set anew washing programme Fill the detergent dispenser with detergent before you set a new washing programme Interrupting a washing programme Open the door e The programme stops Close the door e The programme continues from the point of interruption Setting and starting a washing programme with delay start 1 Press the on off button 2 Set a washing programme 3 Press the delay start button until the dis play shows on flashing the necessary de lay start of the washing programme The delay start indicator light comes on 4 Close the door The number on the display comes on with fixed light The countdown of the delay start starts The countdown of the delay start de creases with steps of 1 hour When the countdown is completed the
15. ection of the water inlet hose is not correct The hose can be kinked or squashed Make sure that the connection is correct There is a blockage in the sink spigot Clean the sink spigot The connection of the water drain hose is not correct The hose can be kinked or squashed Make sure that the connection is correct Close the water tap and contact your local Service Force Centre The appliance door is not closed Close the door Mains plug is not connected in Put in the mains The fuse has blown out in the household fuse box Replace the fuse Delay start is set Cancel the delay start to start the programme immediately After the check switch on the appliance The Product number PNC programme continues from the point of in e Serial number S N terruption If the malfunction shows again For these data refer to the rating plate contact your Service Force Centre Write the necessary data here These data are necessary to help you quickly Model description and correctly e Model Mod Product number Serial number The cleaning results are not satisfactory The dishes are not clean e The selected washing programme is not applicable for the type of load and soil e The basket is loaded incorrectly so that water cannot reach all sur faces e Spray arm does not turn freely because of incorrect arrangement of the load e The filters are dirty or not correctly
16. et keep the door ajar to let the dishes dry naturally This function is available with all washing pro grammes The related indicator light comes on when you press the button Use of the appliance The save energy function has no effect on some programmes Refer to the chapter Washing programmes for the list of pro grammes where save energy has or not an effect Function buttons Use the function buttons for these opera tions e To set the water softener Refer to the chapter Setting the water softener e To cancel the washing programme in pro gress or a delay start in progress Refer to the chapter Setting and starting a washing programme Setting mode The appliance is in setting mode when all programme indicator lights are on The appliance must be in setting mode for these operations To set a washing programme To set the water softener level If a programme indicator light is on cancel the programme to go back to the setting mode Refer to the chapter Setting and starting a washing programme Refer to the following instructions for each step of procedure 1 Make a check if the water softener level is correct for the water hardness in your area If necessary set the water softener Fill the salt container with dishwasher salt Fill the rinse aid dispenser with rinse aid Load cutlery and dishes into the dish washer oN Setting the water softener The water softener re
17. he sides of the cabinet If the door does not close correctly loosen or tighten the ad justable feet until the appliance is level Inlet hose The appliance has safety features to prevent that the water in the appliance goes back into the drinking water system Connected the appliance to a hot max 60 or cold water supply If the hot water comes from alternative sour ces of energy that are more environmentally friendly e g solar or photovoltaic panels and aeolian use a hot water supply to decrease energy consumption It is important that a water tap or stopcock is near the dishwasher with easy access Connect the inlet hose to a water tap with an external thread of 3 4 If the water inlet hose is too short replace the water inlet hose with an applicable longer high pressure hose Do not connect an ex tension hose To suit the installation it is possible to turn the end of the hose that is connected to the dishwasher Do these steps 1 Loosen the retaining nut 2 Turn the hose 8 Tighten the retaining nut Warning Make sure that the retaining nut and all other connections are tight before you move the dishwasher into position Warning Always use a new water inlet hose Do not use connection hoses from an old appliance Drain hose The appliance has water safety system to prevent water damage If there is a malfunc tion the drain pump automatically starts to drain the rem
18. help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Discard the packaging materials in the applicable container at the community waste disposal facilities Warning To discard the appliance follow the procedure e Pull the mains plug out of the socket e Cut off the mains cable and mains plug and discard them e Discard the door catch This prevents the children to close themselves in side the appliance and endanger their lives Do not use multi way plugs connectors and extension cables There is a risk of fire Do not replace the mains cable yourself Contact the Service Force Centre Make sure that the mains plug is acces sible after installation Do not pull the mains cable to discon nect the appliance Always pull the mains plug electrolux 17 18 electrolux electrolux 19 www electrolux com 156985870 00 052009
19. moves minerals and salts from the water supply Minerals and salts can have bad effect on the operation of the appliance 5 Set the correct washing programme for the type of load and soil 6 Fill the detergent dispenser with the cor rect quantity of detergent 7 Start the washing programme If you use detergent tablets refer to the chapter Use of detergent Water hardness is measured in equivalent scales e German degrees dH e French degrees TH 6 electrolux e mmol l millimol per litre international unit Adjust the water softener to the water hard for the hardness of water ness in your area If necessary contact your e Clarke local water authority Water hardness Water hard Digital dis dH mmol l TH Clarke ness setting play level gt 24 gt 4 2 gt 40 gt 28 5 SL 18 24 3 2 4 2 32 40 22 28 4 uy L 12 18 2 1 3 2 19 32 13 22 3 JL 4 12 OTZ 7 19 5 13 2 al lt 4 lt 0 7 ET lt 5 11 it 1 No use of salt required Electronic adjustment The water softener is set at the fac tory at level 3 1 Switch on the appliance 2 Make sure that the appliance is in setting mode 6 3 Press and hold function buttons B and C until the indicator lights of function but tons A B and C start to flash 12 4 Release function buttons B and C 5 Press function button A The indicator lights for function buttons B and C go off Use of dishwasher salt Caution Only use dish
20. n away from the appliance when the door is open Installation Make sure that the appliance is not dam aged because of transport Do not con nect a damaged appliance If necessary contact the supplier Remove all packaging before first use A qualified and competent person must do the electrical installation A qualified and competent person must do the plumbing installation Do not change the specifications or modify this product Risk of injury and damage to the appliance Do not use the appliance Product description electrolux 3 if the mains cable or water hoses are damaged if the control panel worktop or plinth area are damaged that you can get ac cess to the inner side of the appliance Contact your local Service Force Centre Do not drill into the sides of the appliance to prevent damage to hydraulic and elec trical components Warning Carefully obey the instructions for electrical and water connections Spray arm Microfilter Detergent dispenser Rinse aid dispenser Flat filter Fl Salt container 4 electrolux i The rating label is on the back of appli ance Control panel 70 45 700 55 50 Saver o o mo mo O Oo CO0060 o TS 1 19h 70 45 70 55 4 Saver O wf go oOo auto Eco a yi gt I OOOOO L Cancel J On off button Programme selection
21. washers salt Types of salt that are not applicable for dishwashers cause damage to the water softener Caution Grains of salt and salty water The indicator light for function button A continues to flash The digital display shows the current level Example digital display shows J L lev el 3 Press the function button A one time to increase the water softener level by one step Press the on off button to save the oper ation on the bottom of the appliance can cause corrosion Fill the appliance with salt before you start a washing programme to prevent corrosion Do these steps to fill the salt container 1 Turn the cap anticlockwise to open the salt container 2 Fill the salt container with 1 litre of water only the first operation 8 Use the funnel to fill the salt container with salt 5 4 Remove the salt around the opening of the salt container Turn the cap clockwise to close the salt container It is normal that water overflows from the salt container when you fill it with salt Use of rinse aid Caution Only use branded rinse aid for dishwashers Do not fill the rinse aid dispenser with other products e g dishwasher clean ing agent liquid detergent There is a risk of damage to the appliance Rinse aid makes it possible to dry the dishes without streaks and stains Rinse aid is automatically added during the last rinsing phase Do these steps to fill
Download Pdf Manuals
Related Search