Electrolux E40PV100FS User's Manual
Contents
1. Figure 5 Installation 15 INSTALLING THE SUPPORT SYSTEM 1 At hood location install 2 x 4 cross framing between ceiling joists TOP VIEW OF SUPPORT FRAME using dimensions shown in Figure 6 2 Finish the ceiling surface Be sure to mark the location of the deal ceiling joists and cross framing 3 Measure the ceiling height and determine distance between the cook apat ge ira top and bottom of hood 4 Per the chart adjust overall length of the support frame as shown in Figure 7 Remove and reinstall 4 screws in the height adjustment slots to achieve proper length Install 4 additional 3 9 x 9 5mm screws and 4 5 diameter washers from the Hardware Parts Bag SUPPORT FRAME HEIGHT ADJUSTMENT CHART CEILING HOOD DISTANCE ABOVE 36 HIGH COOKTOP SEE NOTE A HEIGHT 24 25 26 97 28 SUPPORT FRAME LENGTH 29 30 es O E E E em ee NOTE A Minimum hood distance above the cook top must not be less than 24 A maximum of 30 above the cook top is highly recommended for best capture of cooking impurities Distances over 30 above the cook top are at the installer s and user s discretion providing that the ceiling height and flue length permit B Requires optional 10 foot flue extension model EXPV100S CEILING JOISTS 5 Secure the support frame to ceiling joists and cross framing with 4 6 x 70mm lag bolts and 6 4 diameter washers provided Make sure the bolts ar2. To reduce risk of fire and to properly exhaust air be sure to duct air outside Do not vent exhaust air into spaces within walls or ceilings or into attics crawl spaces or garages Take care when using cleaning agents or detergents Avoid using food products that produce flames under the Range Hood For general ventilating use only Do not use to exhaust hazardous or explosive materials and vapors To avoid motor bearing damage and noisy and or unbalanced impellers keep drywall spray construction dust etc off power unit Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated The motor will restart when it cools down If the motor continues to shut off and restart have the hood serviced For best capture of cooking impurities the bottom of the hood should be a minimum of 24 and a maximum of 30 above the cooking surface See Installing the Support System section for mounting restrictions Two installers are recommended because of the large size and weight of this hood This product is equipped with a thermostat which may start blower automatically To reduce the risk of injury and to prevent power from being switched on accidentally switch power off at service panel and lock or tag service panel Please read specification label on product for further information and requirements Use with approved cord connection kit only 8 Getting Started OPERATING YOUR H
3. Use amp Care Guide Installation Instructions Vent Hood A Electrolux 2 Finding Information READ AND SAVE THESE INSTRUCTIONS NOTE Installer Leave instructions with owner Owner Read your Hood Use amp Care Manual It contains important safety information for operating this appliance It also has many suggestions for getting the best results from your hood Read all instructions before installing the hood For your safety please read and observe all safety instructions This guide will help you anticipate all installation connections QUESTIONS For toll free telephone support in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 For online support and Internet product information www electroluxusa com 2006 Electrolux Home Products Inc Post Office Box 212378 Augusta Georgia 30917 USA All rights reserved Printed in the USA Finding Information 3 TABLE OF CONTENTS Finding Information cccsssscsssseseeeeseees 2 Please Read And Save This Guide 08 2 Make A Record For Quick Reference 2 QUESTIONS cccccscscscscscsssessscsesescsesestsesestseseseees 2 Table Of Content ccccscesssesseessssesseseeerees 9 E a AEE EAE N E TT T T 4 Important Safety Instructions cceeeeees 4 General Precautions c cccesseseeseeeeeen 5 Getting Started sssesssssssssnsnsnsnsnnnnensannnnnnnsnnnnnna 8 Operating Your Hood
4. Blown fuse Check lamp fuse and replace if open 22 Saving Energy ENERGY SAVING TIPS 1 Do not operate the blower at a speed that is higher than necessary to remove the cooking exhaust Running at excessive speeds removes more air from the inside of the house that must be replaced by outside air This may be especially costly when the housing air conditioning or heating system is in operation Clean filters and grease laden surfaces often to improve efficiency Turn off the blower as soon as all cooking smoke and odors have been eliminated Always use lids on cookware to retain heat and moisture Minimize the amount of liquid used to cook food Select cookware of the proper size material and construction for the cooking task being performed 24 Warranty HOOD WARRANTY Your hood is protected by this warranty WARRANTY THROUGH OUR AUTHORIZED SERVICERS THE CONSUMER WILL BE PERIOD WE WILL RESPONSIBLE FOR FULL ONE YEAR One year from Pay all costs for repairing or replacing any parts of this Costs of service calls that are listed under WARRANTY original purchase product which prove to be defective in materials or NORMAL RESPONSIBILITIES OF THE date workmanship CONSUMER LIMITED Time periods listed All of the provisions of the full warranties above and the Costs of the technician s travel to the home and WARRANTY above exclusions listed below apply any costs for pick up and delivery of the appliance Ap
5. ccccssseeseessseeeeeeeeees 8 Care and Cleaning sssssssssssssrsrsrsnnrnsnsnennnnnnsnsas 11 Cleaning the Filters and Hood cccseeeee 11 INS CAN AUO p r E A 12 Installation Planning 12 Verifying Package Contents ccccseeseeeees 13 Installing the Ductwork 14 Installing the Support System cceeeee 15 Connecting the Decorative Flue 00 16 Installing the Duct Collar cee 16 Mounting the Hood to Support Frame 17 Installing the Electrical cceseeeeees 17 Connecting the DUCtWOFK cceeeeeeeen 18 Replacing the Bottom Trim c cee 18 Installing the Filters cesses 19 Troubleshooting ssceeseeesseeeesseeeeeeseeseeteess 20 If Service iS REQUIFEd ccceeseeteeeeeeees 20 Troubleshooting GUIE ccceeeeeeeeeen 21 Energy Saving TipS cccssesssssssessersseeees 22 Warranty Information ccscsseseeeeen 24 4 Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Warning or Caution based on the risk type Definitions Z This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death AWARNING WARNING indicates a potentially hazardous
6. an outlet near the appliance This appliance should be serviced only by qualified service personnel Contact the nearest Electrolux authorized servicer at 877 435 3287 or at www electroluxusa com for examination repair or adjustment If the information in this manual is not followed exactly a fire or explosion may result Causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Improper installation adjustment alteration service or maintenance can cause personal injury or property damage Refer to these instructions and the accompany ing Use amp Care Manual For assistance or additional information consult a qualified installer service agency or dealer Keep appliance area clear and free from combustible material For general ventilating use only Do not use to exhaust hazardous or explosive materials and vapors To reduce the risk of a range top grease fire a Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings b Always turn hood ON when cooking at high heat or when cooking flaming foods c Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element Safety CAUTION
7. situation which if not avoided could result in death or serious injury ACAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related Safety 5 SAFETY PRECAUTIONS AWARNING Read all instructions before using this appliance Install or locate this appliance only in accordance with these installation instructions Do not operate this appliance if it has a damaged electrical conduit or wires if it is not working properly or if it has been damaged or dropped To reduce the risk of fire electric shock or injury to persons observe the following a Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire rated construction b Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guidelines and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers AS
8. ENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY Note Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you 2 Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary household use The consumer shall pay for such service calls 3 Damages caused by services performed by servicers other than Electrolux Home Products Inc Electrolux Canada Corp or its authorized servicers use of parts other than genuine Electrolux Home Products parts obtained from persons other than such servicers or external causes such as abuse misuse inadequate power supply or acts of God 4 Products with original serial numbers that have been removed or altered and cannot be readily determined IF YOU NEED Keep your bill of sale delivery slip or some other appropriate payment record The date on the bill establishes the SERVICE warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by contacting Electrolux Home Products Inc or Electrolux Canada Corp This warranty only applies in the 50 States of the U S A and Puerto Rico and Canada Product featur
9. HRAE and the local code authorities c When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities d Ducted fans must always be vented outdoors e Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer f Before servicing or cleaning unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel To reduce the risk of fire use only metal ductwork Grounding Instructions This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet this is properly installed and grounded Improper grounding can result in a risk of electric shock Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded Do not use this unit with any separate solid state speed control device 6 Safety WARNING Do not use an extension cord If the power supply cord is too short have a qualified electrician install
10. OOD The hood is operated using the slide controls under the front edge of the hood The light switch turns the halogen lights on and off The blower on off switch turns the blower on to the running cia TWEE EEA speed set by the blower speed control The blower must be ON OFF j j j SWITCH o SPEED ONOFF turned on and off using this switch The blower speed control changes the running speed of the blower 1 2 3 The pilot lamp lights up whenever the blower is on Auto Start Heat Sensing System Your hood is equipped with an Auto Start Heat Sensing System thermostat This thermostat is a device that will turn Figure 1 on or speed up the blower if it senses excessive heat above the cooking surface 1 If blower is OFF it turns blower ON to HIGH speed 2 If blower is ON at a lower speed setting it turns blower up to HIGH speed When the temperature level drops to normal the blower will return to its original setting AWARNING The Auto Start Heat Sensing System thermostat can start the blower even if the hood is turned OFF When this occurs it is impossible to turn the blower OFF with its switch If you must stop the blower do it from the main electrical panel Operation 9 HALOGEN BULBS E O E E E a a a E E a E a E E m a a a E E E This range hood requires four 4 halogen bulbs Type MR16 12V 20W AWARNING Always switch off the electrical supply before performing any operations on the appliance To c
11. ce entrance before wiring 1 Remove the wiring box cover Remove a knockout from the wiring box WIRING BOX COVER 2 Feed 6 of power cable through the knockout opening and secure cable to the wiring box with an appropriate connector 3 Make electrical connections Connect white to white black to black and green to green 4 Replace wiring box cover and screws Check that wires are not pinched between cover and box Figure 13 18 Installation CONNECTING THE DUCTWORK 1 Use 8 round metal duct to connect the discharge collar on the hood to the ductwork above 2 Use duct tape to make all joints secure and air tight 3 Remove the two temporary retaining screws from the lower flue and set it in place on the hood 4 Secure decorative flue to hood with two mounting screws 3 9 x 9 5mm pan head mounting screws 8 ROUND METAL DUCT Figure 14 MOUNTING SCREWWS 3 9 x 9 5 mm Figure 15 REPLACING THE BOTTOM TRIM 1 Remove the four 4 screws from the inside of the hood 2 Remove the trim by pulling downward 3 Slide the new trim upward into hood 4 Replace the four screws inside hood Figure 16 19 INSTALLING THE FILTER S 1 To remove the grease filter grip the latch and pull it down This will disengage the filters from the hood Tilt the filter downward and remove 2 To install the grease filter align rear filter tabs with slots in the hood Pull latch tab down push filter up into po
12. e driven into centers of joists and cross framing for f f MOUNTING j maximum strength See Figure 8 SCREWS 6 x 70mm 6 Run 2 wire plus ground electrical cable through the hole on top of the support frame bracket Cable length must extend at least 12 below the bottom of the support frame Secure cable to the support SUPPORT frame with an appropriate cable connector HEIGHT ADJUSTMENT SLOTS Figure 8 16 Installation CONNECTING THE DECORATIVE FLUE 1 Secure the upper flue to the upper support frame with the mounting screws 3 9 x 9 5mm 2 Insert the lower flue moving it completely towards the top and secure it temporarily with retaining screws 3 9 x 9 5mm MOUNTING 3 FS INSERT THE LOWER FLUE 3 XJ0mmM RETAINING 3 9 x 9 5mm A Figure 10 FLUE Figure 9 INSTALLING THE DUCT COLLAR 1 Fold the 2 tongues outwards 2 Secure the discharge collar to the hood with 2 retaining screws 3 90 x 9 5mm RETAINING SCREWS 3 9 x 9 5mm PR Figure 11 Installation 17 MOUNTING THE HOOD TO SUPPORT FRAME 1 Insert four 4 bolts through the top of the hood from the inside 2 Use four 4 nuts and four 4 washers to secure hood to support frame WASHER ut Figure 12 INSTALLING THE ELECTRICAL AWARNING Electrical wiring must be done by a qualified person s in accordance with all applicable codes and standards This range hood must be properly grounded Turn off electrical power at servi
13. es or specifications as described or illustrated are subject to change without notice All warranties are made by Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp USA Canada 1 877 4ELECTROLUX 1 866 294 9911 Electrolux Home Products Inc Electrolux Canada Corp P O Box 212378 6150 McLaughlin Road Augusta GA 30917 Mississauga Ontario L5R 4C2
14. hange bulbs 1 Loosen the ring nut by turning it counterclockwise 2 Remove the bulb by pulling downward DO NOT ROTATE ACAUTION Bulb may be hot 3 Replace with a bulb of the same type MR16 12V 20W Do not touch replacement bulb with bare hands ACAUTION o Use of bulbs greater than 20 watts will cause the fuse to open MASA Figure 2 10 Operation FUSE REPLACEMENT IF LIGHTS FAIL TO OPERATE DISCONNECT POWER AT THE SERVICE ENTRANCE CHECK THE FUSE AND REPLACE IF NECESSARY 1 Remove grease filters 2 Remove the electrical box support and open the fuse box 3 Unscrew the cap from the fuse holder and remove the fuse 4 Replace the fuse with the same size and amperage 5 x 20mm 4 amp 125 volt ACAUTION Use of a fuse greater than 4 amps may damage the transformer FUSE S Figure 3 5 Reconnect power at the service entrance Care and Cleaning 11 CLEANING THE FILTERS AND HOOD Proper maintenance of the Range Hood will assure proper performance of the unit Grease Filters The grease filters should be cleaned frequently Use a warm detergent solution Grease filters are dishwasher safe See INSTALL FILTERS section for removal and installation instructions Hood Cleaning Stainless steel is one of the easiest materials to keep clean Occasional care will help preserve its fine appearance Cleaning tips 1 Hot water with soap or detergent is all that is usually needed 2 Follow all c
15. hown provide minimum clearances unless otherwise noted Make certain that you have everything necessary to ensure a proper installation before proceeding Installation 13 VERIFY PACKAGE CONTENTS Unpack hood and check contents You should receive 1 Hood 1 Decorative Flue Assembly 1 Support Frame 1 Duct Collar 1 Parts Bag containing 8 Washers 6 4 4 Washers 4 5 4 Lag Bolts 8 Mounting Screws 3 9 X 9 5mm Pan Head 4 Hex Nuts 1 Installation Instructions 2 Warranty Cards 4 HEX NUTS DUCT COLLAR DECORATIVE SUPPORT 8 WASHERS 4 Lag Bolts FLUE 26 4 FRAME 6x70mm T gt 4 WASHERS 8 MOUNTING SCREWS 04 5 3 9 x 9 5mm Pan Head Figure 4 14 Installation ROOF CAP 24 to 30 ABOVE COOKING INSTALLING THE DUCTWORK ACAUTION To reduce the risk of fire use only metal ductwork 1 Decide where the ductwork will run between the hood and the outside Figure 5 2 Astraight short duct run will allow the hood to perform most efficiently 3 Long duct runs elbows and transitions will reduce the performance of the hood Use as few of them as possible Larger ducting may be required for best performance with longer duct runs 4 Install a roof or wall cap Connect round metal ductwork to cap and work back towards hood location Use duct tape to seal the joints between ductwork sections SURFACE See Install Mounting Bracket section for mounting amp restrictions
16. leaning by rinsing with clear water Wipe dry with a clean soft cloth to avoid water marks 3 For discolorations or deposits that persist use a non scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth 4 For stubborn cases use a plastic scouring pad or soft bristle brush together with cleanser and water Rub lightly in direction of polishing lines or grain of the Stainless finish Avoid using too much pressure which may mar the surface 5 DO NOT allow deposits to remain for long periods of time 6 DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust 7 DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth Painted surfaces should be cleaned with warm water and mild detergent only 12 Installation INSTALLATION PLANNING A qualified installer must complete the installation of this built in appliance Proper installation is your responsibility Carefully check the location where the hood is to be installed The hood should be placed for convenient access Make certain that electrical power can be provided in the selected location Plan the installation so that all minimum clearances are met or exceeded Dimensions s
17. plicable to the required because of service State of Alaska In the U S A your appliance is warranted by Electrolux Home Products Inc We authorize no person to change or add to any of our obligations under this warranty Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products Inc servicer In Canada your appliance is warranted by Electrolux Canada Corp NORMAL This warranty applies only to products in ordinary household use and the consumer is responsible for the items RESPONSIBILITIES listed below OF THE CUSTOMER 1 Proper use of the appliance in accordance with instructions provided with the product 2 Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing electrical and or gas codes 3 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring 4 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it was shipped from the factory 5 Damages to finish after installation 6 Replacement of light bulbs and or fluorescent tubes on models with these features EXCLUSIONS This warranty does not cover the following 1 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCID
18. sition and release the tab Make sure the filter is securely engaged after installation NOTE Prior to use remove protective film from the filter frame GREASE FILTERS Figure 17 20 Troubleshooting IF SERVICE IS REQUIRED First review the recommended checks listed in the Troubleshooting Guide Then be certain that the appliance has been installed properly and is being operated correctly Familiarize yourself with the warranty terms and conditions listed in the Warranty section If the above checks have been completed and the problem has not yet been remedied contact the dealer where you purchased the unit State the Model and Serial number and explain the problem The Model and Serial number plate is located inside the unit at upper right hand corner If you do not know the name of the selling dealer or local service company you can check online at www electroluxusa com Troubleshooting 21 TROUBLESHOOTING GUIDE IMPORTANT Unnecessary service calls may be expensive frustrating and time consuming Before you call for service please review the potential problems possible causes and remedies shown in the table below Troubleshooting What to check when problems occur Problem Possible Cause Nothing works Vent power supply Have electrician check power supply interrupted or not energized including house circuit breaker and fuses Lights do not turnon Aloose or burned out light Check the light
Download Pdf Manuals
Related Search