Electrolux CHDD 8795 User's Manual
Contents
1. L or coloured red 65 Wall unit mounting Fig 8 9 10 11 e Place the three rubber strips on the back of the cooker hood Where necessary mount the two spacers provided on the drill holes for definitive fixing The spacers are useful when the wall which is to house the cooker hood is not perfectly vertical for example where it is partially covered with wall tiles rubber strips rubber strips rubber strips XI US definitive fixing LS Q Fig 8 Spacers 66 Mark the wall with a centre line this will aid mounting procedure 1 position the template so that the mid line printed on the template matches with the centre line previously marked the lower side of the template corresponds to the lower side of the hood once mounted 2 Drill two holes 8mm and fix the support bracket with two wall plugs and screws 3 Remove the front panels see paragraph Removing the front panels Hang the hood 4 adjust its position 5 6 and from the inside of the hood sign two points for definitive fixing 7 remove the hood and drill two holes 8mm 8 fit two wall plugs hang the hood again and fix it securely with two screws 9 Cover the drill holes for screws with the two screw caps provided 67 14 Fix the sides of the cooker hood by fastening the pins 10a to the sides of the fastening screws 10b Only DD 8794 not UK side panels are available as a special acc2. hood is used Re setting the saturation signal After cleaning or replacing the filter select the intensive speed the control ball lights up with a red flashing light depress again and hold depressed for about 3 seconds until an audible signal indicates the reset has taken place 58 Maintenance and care The hood must always be disconnected from the electricity supply before beginning any maintenance work Cleaning the hood Clean the outside of the hood using a damp cloth and a mild deter gent Never use corrosive abrasive or flammable cleaning products Never insert pointed objects in the motor s protective grid Wash the outside surfaces using a delicate detergent solution Never use caustic detergents or abrasive brushes or powders Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents It is extremely important to clean the unit and change the filters at the recommended intervals Failure to do so will cause grease deposits to build up that could constitute a fire hazard Metal grease filter Removing the front panels The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used either in the external extraction or internal recycling function Attention the metal grease filters must be removed and washed either by hand or in the dishwasher every four weeks To access the grease filter first remove the fro
3. maintenance or failure to observe the above safety recommendations Disconnect the cooker hood from the main supply Remove the lamp use a screw driver as a lever Fig 7 Remove the connector Replace the old bulb with a new one of the same type Refit the connector Zo If the light does not come on make sure the bulb has been inserted correctly before contacting your local Service Force Centre Fig 7 Special accessories Charcoal filter KF 14 E Nr 942 120 604 Remote control RM 8700 942 120 658 Telescopic chimney for extractor version only 942 120 750 Stainless steel side panels Only DD 8794 942 120 768 Aluminium side panels 942 120 769 Not available in UK please contact your local Service Force Centre Technical assistance service not for UK You are welcome to telephone our technical assistance service see list of technical assistance centres whenever you need information or in the unlikely event of a fault When calling please be ready to specify 1 The model code number 2 The serial number E Nr 3 Themanufacturing number F Nr This information is shown on the registration plate inside the unit behind the grease filter We reserve the right to change specifications and colours as a result of our policy of continuing technological development Service and spare parts for UK In the event of your appliance requiring service or if you wish to purchase spare parts contact y
4. rooms in which fuel burning appliances are installed The air outlet installation must comply with the regulations laid down by the relevant authorities When the unit is used in its extractor version a sufficiently large ventilation hole must be provided with dimensions that are approxi mately the same as the outlet hole National and regional building regulations impose a number of restrictions on using hoods and fuel burning appliances connected to a chimney such as coal or oil room heaters and gas fires in the same room Hoods can only be used safely with appliances connected to a chimney if the room and or flat air environment combination is ventilated from outside using a suitable ventilation hole approximately 500 600 cm large to avoid the possibility of a depression being created during operation of the hood If you have any doubts contact the relevant controlling authority or building inspector s office Since the rule for rooms with fuel burning appliances is outlet hole of the same size as the ventilation hole a hole of 500 600 cm which is to say a larger hole could reduce the performance of the extractor hood If the hood is used in its filtering function it will operate simply and safely in the above conditions without the need for any of the aforementioned measures When the hood is used in its extractor function the following rules must be followed to obtain optimal operation sh
5. DD 8794 DD 8795 CHDD 8795 Dunstabzugshaube Afzuigkap Hotte Cooker Hood Campana extractora Montage und Gebrauchsanweisung Installatie en gebruiksaanwijzing Notice d utilisation et d installation Operating and Installation Instructions Instrucciones de montaje y manejo Contents Safety warnings For the user For the installer Description of the Appliance Extractor version Filter Version Control Panel Switching on the hood Switching on the light Control device for grease or charcoal filter Led signal for grease filter Led signal for charcoal filter Re setting the saturation signal Maintenance and care Cleaning the hood Metal grease filter Removing the frontal screens Removing the metal grease filter Charcoal filter Changing the light bulb Special accessories Technical assistance service Technical Specifications Mounting accessories included Electrical connection Wall unit mounting Printed on recycled paper AEG putting words into action SSSS 9598589893 S958 REEF R238888 BR 92 8 8 53 54 AN Safety warnings For the user The cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam Always cover heating elements to prevent excess heat from damaging the appliance In the case of oil gas and coal fired cookers it is essential to avoid open flames Also when frying keep the deep frying pan on the cooker top cooker under ca
6. Panel e Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated Turn the hood on a few minutes before you start cooking you will then get an under pressure in the kitchen The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared e The hood operation can be controlled via the control ball or with the remote control the remote control is a special accessory and is ordered separately Every change changing speed switching on the lights etc is recognizable from the variation of light emitted by the control ball and by an acoustic signal The control ball is located below on the right side of the cooker hood The control ball is also a light signal e No signal The hood is switched off Static green light Hood is switched on at power level 1 minimum Static orange light Hood is switched on at power level 2 medium Static red light Hood is switched on at power level 3 maximum Flashing red light Hood is switched on at intensive power level timed at 5 minutes Flashing green light Indicates the grease filter saturation clean the grease filter Flashing orange light Indicates the charcoal filter saturation clean or replace the charcoal filter Attention The control ball flashes orange to indicate the saturation of the charcoal filter even if the hood is used in the extractor version and
7. essory please contact your local Service Centre or see paragraph Special Accessory Block the sides sliding the two tabs outwards 11 Make electrical connection 12 but leave the hood disconnected from the home general electric panel In the case that it is decided to use the cooker hood in the suction version then place one of the two flanges provided in the exit hole 13 Suction Attention The tall flange should be used when a telescopic chimney is required to be mounted this item should be ordered see special accessories the short flange is to be used in all other cases Remount the grease filter and the front panels according to the numbering noted also on the back of each screen from 1 to 4 from the top to the bottom Connect the hood the the home general electric panel and check ifthe hood work properly AEG Hausgerate GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de http www aeg co uk Copyright by AEG LI10UE Ed 04 03
8. lange O 150 125 mm 2 flanges 150 mm Only DD 8795 and CHDD 8795 2 Stainless Steel side panels Electrical connection not for UK Safety warnings for the electrician Before connecting the appliance to the power supply check that the voltage indicated on the rating plate corresponds to the mains power supply available Appliances fitted with a plug can be connected to any standard power socket within easy access Should it be necessary to provide a fixed connection the hood must only be installed by an electrician authorised by the local electricity board When installing an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided Fixed connection of the appliance must only be carried out by an authorised electrician Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts The switch must be accessible at all times The following is valid in the United Kingdom only the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol L or coloured green or green and yellow the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black the wire which is coloured brown must be connected to the terminal which is marked with the letter
9. no charcoal filter is fitted In this case perform the signal reset operation as follows select the intensive speed the control ball lights up with a red flashing light depress again and hold depressed for about 3 seconds until an audible signal indicates the reset has taken place 57 Switching on the hood Fig 3 depress towards the bottom to switch on The control ball is a balancer switch the hood Depressing the control ball repeatedly towards the bottom switches on the hood and you may select the motor level desired depressing once again the hood switches off C Switching on the light Fig 3 Y Depress the control ball towards the top once for submersed lighting A once again for full lighting depress again to switch off the light a Indicator light for grease or dapreas towards charcoal filter the top to switch p on the lights The air duct in this hood includes a device that signals when the filter requires cleaning or changing Led signal for grease filter The LED signal flickers flickering green light when the grease filter requires cleaning occurs at about 40 operating hours Ensure that the indicator light is checked each time the hood is used Fig 3 Led signal for charcoal filter The LED signal flickers flickering orange light when the charcoal filter requires cleaning occurs at about 160 operating hours Ensure that the indicator light is checked each time the
10. nt panels which conceal the grease filter Extract the small panel rotate upwards and unhook Repeat the operation for all the small panels Fig 4 59 Removing the metal Handle grease filter Pull the handle downards then extract the filter Fig 5 Hand washing Soak grease filter s for about one hour in hot water with a grease loosening cleaner then rinse off thoroughly with hot water Repeat the process if necessary Refit the grease filters when they are dry Dishwasher Place grease filters in the dishwasher Select most powerful washing programme and highest temperature at least 65 C Repeat the process Refit the grease filters when they are dry When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur this does not have any impact on its performance e Clean the inner housing using a hot detergent solution only never use caustic detergents abrasive powders or brushes After having re installed the grease filter remount the front panels following the instructions for removal in reverse The narrower front panel is to be mounted at the highest position 60 Charcoal filter The charcoal filter should only be used if you want to use the hood in the recirculation function To do this you will need an original AEG charcoal filter available from your local Service Force Centre Cleaning replacing the carbon filter Unlike other carbon filters
11. ort and straight outlet hose keep bends in outlet hose to a minimum never install the hoses with an acute angle they must always follow a gentle curve keep the hose as large as possible preferably the same diameter as the outlet hole Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood 55 Description of the Appliance e The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter You will need an original AEG charcoal filter for this function Available from your local AEG Service Force Centre Extractor version e nthis version fumes are extracted to the outside via reduction a hose connected to the coupling ring Fig 1 coupling ring flange norderto obtain the best performance the hose should have a diameter equal to the outlet hole e Should there already bea pipe of diameter 125 mm that ducts to the outside through the walls or roof it is possible to use the 150 125 mm reduction flange provided In this case the hood will be slightly noisier Filter Version e The air is filtered through a charcoal filter and returned to Deflector the kitchen You will need an original AEG charcoal filter for the filtering function See Special Accessories Fixthe deflector using 2 screws 3 5x9 5 mm Fig 2 56 Control
12. our local AEG Service Force Centre by telephoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Please ensure that you have read the section What to do if as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty Please note that proof of purchase is required for in guarantee service calls Help us to help you Please determine your type of enquiry before writing or telephoning When you contact us we need to know e Your name Clear and concise details of the fault e Address and postcode s Name and model of the appliance Telephone number e E number This information can be found on the rating plate which can be seen when the grease filters are removed T 64 Technical Specifications Dimensions in cm Height x Width x Depth 80 x 89 8 x 33 5 Maximum absorbed power 235 W Motor absorption 175W Lighting 3x 12V 20W halogen lamps Type GU4 Length of the cable 150cm Electrical connection 230 V Mounting accessories included 1 support bracket 1 deflector 3 Rubber strips 2 Screw caps 1 template 2 spacers 4 wood screws 5 x 45 mm 4 wall plugs 8 mm 2 metal screws 3 5 x 9 5 2 metal screws 3 5 x 32 1 reduction f
13. reful control The hot oil in the frying pan might ignite due to overheating The risk of self ignition increases when the oil being used is dirty It is extremely important to note that overheating can cause a fire Never carry out any flamb cooking under the hood Always disconnect the unit from the power supply before carrying out any work on the hood including replacing the light bulb take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker It is very important to clean the hood and replace the filter at the recommended intervals Failure to do so could cause grease deposits to build up resulting in a fire hazard For the installer When used as an extractor unit the hood must be fitted with a 150mm diameter hose Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof it is possible to use the 150 125 mm reduction flange provided In this case the hood will be slightly noisier When installing the hood make sure you respect the following minimum distance from the top edge of the cooking hob ring surfaces electric cookers 300 mm gas cookers 300 mm coal and oil cookers 400 mm min The national Standard on fuel burning systems specifies a maximum depression of 0 04 mbar in such rooms The air outlet must not be connected to chimney flues or combustion gas ducts The air outlet must under no circumstances be connected to ventilation ducts for
14. the LONGLIFE carbon filter can be cleaned and reactivated At normal use the filter should be cleaned every second month when using the hood 2 5 hours per day in avarage The best way to clean the filter is in the dishwasher Use normal detergent and choose the highest temperature 65 C Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours To reactivate the carbon the filter should be dried in an oven for 10 minutes with a temperature of maximum 100 C After approximately three years of use the charcoal filter should be replaced with a new as the odour reduction capacity will be reduced Fitting Fit the charcoal filter on the rear side of the grease filter fix it with two metal wires Fig 6 To remove proceed in the reverse order charcoal filter Always specify the hood metal wires model code number and as serialnumber when ordering replacement filters This information is shown on the registration plate located on the inside of the unit The charcoal filter can be ordered from your local AEG Service Force Centre grease filter 61 62 Changing the light bulb Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard You are therefore strongly recommended to follow these instructions The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate
Download Pdf Manuals
Related Search