Electrolux 50877 User's Manual
Contents
1. d Rinse aid dispenser activated 4 To change the setting press button B again the digital display indicates the new setting 5 To memorise the operation switch off the dishwasher by pressing the On Off button i If you decide to turn back to the use of standard detergent system we advise that you 1 Deactivate the Multitab function 2 Fill up the salt container and the rinse aid dispenser again 3 Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes 4 Adjust the water hardness setting according to the hardness of the water in your area 5 Adjust the rinse aid dosage Washing programmes Programme Degree of Type of Programme description Consumption val soil load ues Z 2 P la la o Maea E Ial a So 2 z 2 Sl a T D 2 Ela a a i s AUTOMATIC2 Mixed nor Crockery e see Q gt g mal and cutlery de i a heavy soil pots and gS ae pans 30 MIN Light soil Crockery e 8 2 gt and cutlery INTENSIV Heavy soil Crockery fe o o 2 CARE 70 cutlery Fa TE pots and e ee pans Select and start a washing programme Programme Degree of Type of Programme description soil load co T n vu s E z s 3 2 o gt D vu vu oO 5 Z oO it a ui ECO 50 Normal Crockery e o o o 2 z 2 soil and2. 45 51 64 5 1 6 4 2 level 7 yes 28 35 40 50 4 0 5 0 2 evel 6 yes 23 27 33 39 3 3 3 9 2 level 5 yes 18 22 26 32 2 61 3 2 1 evel 4 yes 13 17 19 25 1 9 2 5 1 level 3 yes 5 12 7 18 0 71 1 8 1 evel 2 yes lt 5 lt 7 lt 0 7 1 level 1 no The water softener must be set in both ways manually using the water hardness dial and electronically Setting manually i The dishwasher is factory set at position 2 1 Open the dishwasher door 2 Remove the lower basket from the dishwasher 3 Turn the water hardness dial to posi tion 1 or 2 see table 4 Replace the lower basket Use of dishwasher salt Setting electronically i The dishwasher is factory set at level 5 1 2 Press the On Off button The dishwasher must be in setting mode Press simultaneously and keep pressed buttons B and C until the lights of buttons A B and C start flashing Press button A the lights of buttons B and C turn off while the light of button A goes on flashing In the digital display is visible the current level Examples S L displayed level 5 IO L displayed level 10 To change the level press button A Each time the button is pressed the level changes for the selection of the new level see the chart Examples if the current level is 5 by pressing button A once level 6 is selected if the current level is 10 by pressing button A once level 1 is selected To memorise the operation
3. Check the water drain hose connection 130 appears in the digital display e Close the water tap and contact your local Anti flood device is activated Service Force Centre What to do if Fault code and malfunction Possible cause and solution The programme does not start e The dishwasher s door has not been properly closed Close the door e The main plug is not plugged in Insert the main plug e The fuse has blown out in the household fuse box Replace the fuse e Delay start has been set If dishes are to be washed immediately cancel the delay start Once these checks have been carried out switch on the appliance the programme will continue from the point at which it was interrupted If the malfunction or fault code reappears contact the Service Force Centre For other fault codes not described in the above chart please contact your local Service Force Centre quoting the model Mod product number PNC and serial number S N This information can be found on the rating plate located on the side of the dishwasher door So that you always have these numbers at hand we recommend you to make a note of them here Technical data The wash results are not satisfactory The dishes are not clean The dishes are wet and dull There are streaks milky spots or a bluish coating on glasses and dishes Water drops have dries onto glasses and dishes he wrong washing programme has been se lected
4. Washing programmes chart When a programme has been selected the corresponding light will illuminate Close the dishwasher s door the programme starts automatically Select and start a washing programme i i AN Setting and starting the programme with delay start 1 After having selected the washing programme press the delay start button until the flashing number of hours for the delay start will appear in the digital display You can choose from 1 to 19 hours of delay 2 Close the dishwasher s door the countdown starts automatically The number in the display is no longer flashing but fixed with static light 3 The countdown will decrease with steps of 1 hour 4 The opening of the door will interrupt the countdown 5 Once the delay start has elapsed the programme will start automatically With the delay start function set the programme in progress indicator light is off Once the countdown of the delay start has elapsed the washing programme will start automatically and the programme in progress indicator light will illu minate The selection of the washing programme and delay start can also occur with the door closed Keep in mind that in this way once a washing programme button is pressed you have ONLY 3 seconds in which you can choose another programme or select a delay start after which the selected programme will start automatically Cancelling the delay start and or a washing programme e To canc
5. and lock by turning the handle clock wise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment AN WARNING NEVER use the dishwasher without filters Incorrect repositioning and fitting of the filters will produce poor washing results and may result in damage to the appliance Care and cleaning Cleaning the spray arms i NEVER try to remove the spray arms If residues of soil have clogged the holes in the spray arms remove them with a cocktail stick External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scour ing pads or solvent acetone trichloroethylene etc Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes Prolonged periods of non operation If you are not using the machine for any prolonged period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the formation of any unpleasant smells 3 Leave the inside of the machine clean Frost precautions Avoid placing the machine ina location where the temperature Is below 0 C If this is unavoidable empty
6. switch off the dishwasher by pressing the On Off button Use of dishwasher salt AN WARNING Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in a dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion To fill Is Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise Pour 1 litre of water inside the container this is necessary only before filling with salt for the first time Use of rinse aid 3 Using the funnel provided pour in the salt until the container is full 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Replace the cap tightly turning it clockwise until it stops with a click i Do not worry if water overflows from the unit when filling with salt this is quite normal i The salt indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The function of t
7. the indication of the running time of the programme is automatically updated Once the programme is running the Multitab function can NO longer be changed If you want to exclude the Multitab function you have to cancel the programme setting and then deactivate the Multitab function In this case you have to set a washing programme and desired options again Activation deactivation of the Multitab function Simultaneously press and hold the two Multitab buttons D and E until the Multitab function indicator light illuminates This means that the function is ac tive To deactivate the function press the same buttons again until the Multitab func tion indicator light turns off i If the drying results are not satisfactory we suggest that you 1 Fill up the rinse aid dispenser with rinse aid 2 Activate the rinse aid dispenser 3 Set the rinse aid dosage to position 2 e The activation deactivation of the rinse aid dispenser can only be possible with the Multitab function active Activation deactivation of the rinse aid dispenser 1 Press the On Off button The dishwasher must be in setting mode 2 Press simultaneously buttons B and C until the lights of buttons A B and C start flashing 3 Press button B the lights of buttons A and C turn off while the light of button B goes on flashing The digital display indicates the current setting D d Rinse aid dispenser deactivated Washing programmes
8. cutlery z i y o CRE 2 Yas Normal Delicate e o o o o a je soil crockery e AU per and glass alls ware 1 The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes 2 During the Auto washing programme the amount of soil on the dishes is determined by how cloudy the water is The programme duration water and energy consumption levels can vary this depends upon if the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled The temperature of the water is automatically adjusted between 45 C and 70 C 3 Ideal for washing a partially loaded dishwasher This is the perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery 4 Test programme for test institutes Select and start a washing programme i Select the washing programme and delay start with the door slightly opened The start of the programme or the countdown of the delay start will occur only after the closure of the door Until then it is possible to modify the settings 1 Check that the baskets have been loaded correctly and that the spray arms are free to rotate Check that the water tap is opened Press the On Off button all the programme lights illuminate setting mode 4 Press the button corresponding to the required programme see
9. lid and press until it locks in place i Detergent tablets Detergent tablets from different manu factures dissolve at different rates For this reason some detergent tablets do not at tain their full cleaning power during short washing programmes Therefore please use long washing programmes when us ing detergent tablets to ensure the complete removal of detergent residuals Multi tab function This appliance is equipped with the Multitab function that allows the use of the Multitab combi detergent tablets These products are detergents with a combined cleaning rinsing and salt functions They can also contain other different agents depending on which kind of tablets you choose 3 in 1 4in 1 5 in 1 etc Check whether these detergents are suitable for your water hardness See the manufacturers instructions This function can be selected with all washing programmes With the selection of this function the inflow of rinse aid and salt from each respective supply container Multi tab function is automatically deactivated and also the indicator lights for salt and rinse aid are deactivated Select the Multitab function before the start of a washing programme Once this function is selected indicator light illuminated it will remain active also for the following washing programmes With the use of the Multitab function the cycle durations may change In this case in the digital display
10. the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off What to do if 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during transportation What to do if The dishwasher will not start or stops during operation Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the indications described in the chart without calling out an engineer Switch off the dishwasher and carry out the following suggested corrective actions Fault code and malfunction Possible cause and solution IL appears in the digital display e The water tap is blocked or furred with lime The dishwasher does not fill with water scale Clean the water tap e The water tap is turned off Turn the water tap on e The filter where present in the threaded hose fitting at the water inlet valve is blocked Clean the filter in the threaded hose e The water inlet hose has not been correctly aid or it is bent or squashed Check the water drain hose connection cu appears in the digital display e The sink spigot is blocked The dishwasher will not drain Clean out the sink spigot e The water drain hose has not been correctly laid or it is bent or squashed
11. the two rear retaining screws pull the worktop from the back of the machine and slide out the front slots lifting the worktop 2 Insert the machine after adjusting the levelling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been installed it is easily accessible for the service engineer in the event that a repair is required If the dishwasher is later used as a free standing appliance the original worktop must be re mounted The plinth on free standing appliances is not adjustable Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level Water supply connections Connection to a cold water supply is advised If connection is made to a hot water supply the maximum permissible temperature is 60 C A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto a 3 4 gas thread spout or to a purpo
12. FAVORIT 50877 User manual Dishwasher A i Q Dear Customer Thank you for choosing one of our high quality products With this appliance you will experience the perfect combination of functional design and cutting edge technology Convince yourself that our appliances are engineered to deliver the best performance and control indeed we are setting the highest standards of excellence In addition to this you find environmental and energy saving aspects as an integral part of our products To ensure optimal and regular performance of your appliance please read this instruction manual carefully It will enable you to navigate all processes perfectly and most efficiently To refer to this manual any time you need to we recommend you to keep itin a safe place And please pass it to any future owner of the appliance We wish you much joy with your new appliance The following symbols are used in this user manual Important information concerning your personal safety and information on how to avoid damaging the appliance General information and tips Environmental information 117970660 12022008 Contents Contents Operating instructions 5 Safety information 5 Correct use 5 General safety 6 Child safety 6 Installation 6 Product description 7 Control panel 8 The digital display 9 Function buttons 9 Setting mode 9 To cancel a set programme or a programme in progress 10 First us
13. The dishes are arranged in such a way as to stop water reaching all parts of the surface The baskets must not be overloaded The spray arms do not rotate freely due to ncorrect arrangement of the load he filters in the base of the washing com partment are dirty or incorrectly positioned Too little or no detergent has been used Where there are limescales deposits on the dishes the salt container is empty or the in correct level of the water softener has been set The drain hose connection is not correct The salt container cap is not properly closed Rinse aid was not used The rinse aid dispenser is empty Decrease rinse aid dosing Increase rinse aid dosing The detergent may be the cause Contact the detergent manufacturer s consumer care line If after all these checks the problem persists contact your local Service Force Cen tre Technical data Dimension Electrical connection Voltage Overall power Fuse Water supply pressure Capacity Place settings Max weight kg Width height depth cm Minimum Maximum MPa 60 x 85 x 63 5 Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher s door 0 05 0 8 12 45 Hints for test institutes Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme see Washing programmes Test in a
14. ccordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with salt and rinse aid respectively and using the test programme see Washing programmes Full load 12 standard place settings Amount of detergent required 5 g 25 g Type B Rinse aid setting position 4 Type III Hints for test institutes Example loading arrangements Upper basket 1 Lower basket with cutlery basket Cutlery basket M I h S X E PNN AA lt a ES M 7 CS KOY WE 1 If there are cup racks in place on the lefthand side remove them Installation Installation instructions Installation AN WARNING Any electrical and or plumbing work required to install this appliance should be carried out by a qualified electrician and or plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Fitting under a counter kitchen worktop or sink By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows 1 Remove the machine s worktop by unscrewing
15. e 10 Set the water softener 10 Setting manually 11 Setting electronically 12 Use of dishwasher salt 12 Use of rinse aid 13 Adjusting the dosage of rinse aid 14 Daily use 14 Load cutlery and dishes 15 The lower basket 16 The cutlery basket 17 The upper basket 18 Adjusting the height of the upper basket 19 Use of detergent 20 Fill with detergent 20 Multi tab function 21 Activation deactivation of the Multitab function 22 Washing programmes 23 Contents Select and start a washing programme 24 Unloading the dishwasher 26 Care and cleaning 26 Cleaning the filters 26 Cleaning the spray arms 28 External cleaning 28 Internal cleaning 28 Prolonged periods of non operation 28 Frost precautions 28 Moving the machine 28 What to do if 29 Technical data 31 Hints for test institutes 32 Installation instructions 34 Installation 34 Fitting under a counter kitchen worktop or sink 34 Levelling 35 35 Water supply connections 35 Water outlet hose connection 36 Electrical connection 37 Environment concerns 38 Packaging material 38 Subject to change without notice Safety information Operating instructions Safety information In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully including its hints and warnings To avoid unnecessary mistakes and accidents it is important to ensure that all people using th
16. e appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety Correct use This dishwasher is only intended for washing household utensils suitable for machine washing Do not put any solvents in the dishwasher This could cause an explosion Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket Only use products detergent salt and rinse aid suitable for dishwashers Avoid opening the door whilst the appliance is in operation hot steam may escape Do not take any dishes out of the dishwasher before the end of the dishwashing cycle After use isolate the appliance from the power supply and turn off the water supply This product should be serviced only by an authorised service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons will cause injury or serious mal functioning Contact your local Service Force Centre Always insist on genuine spare parts BEM Safety information General safety e Dishwasher detergents can cause chemical burns to eyes mouth and throat Could endanger life Comply with the
17. e lower basket With upper basket raised 22 cm 30 cm With upper basket lowered 24 cm 29 cm i The height of the upper basket can also be adjusted when it is loaded Raising lowering the upper basket Use of detergent 1 Pull out the upper basket completely 2 Holding the upper basket by the han dle raise it as far as it will go and then lower it vertically The upper basket will latch into the lower or the upper position A WARNING After loading your machine always close the door as an open door can be a hazard i Before closing the door ensure that the spray arms can rotate freely Use of detergent i Only use detergents specifically designed for use in dishwashers Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging W Using no more than the correct amount of detergent contributes to reducing pol lution Fill with detergent 1 Open the lid Multi tab function 2 Fillthe detergent dispenser 1 with detergent The marking indicates the dosing levels 20 approximately 20 g of detergent 30 approximately 30 g of detergent 3 All programmes with prewash need an additional detergent dose 5 10 g that must be placed in the prewash detergent chamber 2 This detergent will take effect during the prewash phase 4 When using detergent tablets place the tablet in compartment 1 5 Close the
18. el a delay start in progress you have to reset the dishwasher e Cancelling a delay start involves also the cancelling of the washing programme set In this case you have to set the washing programme again If anew washing programme is to be selected check that there is detergent in the detergent dispenser WARNING Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened Open the door carefully Interrupt a washing programme in progress Open the dishwasher door the programme will stop Close the door the pro gramme will start from the point at which it was interrupted e Press the On Off button all lights will turn off Press the On Off button again the programme will start from the point at which it was interrupted End of the washing programme e The dishwasher will automatically stop Unloading the dishwasher e The light of the programme just ended will remain on e n the digital display appears a zero 1 Switch off the dishwasher by pressing the On Off button 2 Open the dishwasher s door leave it ajar and wait a few minutes before re moving the dishes in this way they will be cooler and the drying will be improved Unloading the dishwasher e Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appliance e Empty the lower basket first and then the upper o
19. ems such as knives To ensure that all items of cutlery in the cutlery basket can be reached by the water you should 1 Place the grid insert on the cutlery basket 22227 243714 a COC TT 4J411111111 yugu agayiitijit wUdjsaaaadd 3480222277 Load cutlery and dishes 2 Place forks and spoon in the cutlery basket with their handles pointing downwards For larger utensils such as whisks leave off one half of the cutlery grid The upper basket Load smaller fragile crockery and long sharp cutlery in the upper basket e Arrange items of crockery on and under the HH folding cup racks so that they are offset from each other and water can reach all items e The cup racks can be folded up out of the way for tall crockery items e Lay or hang wine and brandy glasses in the slots in the cup racks Load cutlery and dishes BEC e For glasses with long stems fold the glass rack to the right otherwise fold it away to the left e The row of spikes on the left of the upper basket is also in two parts and can be folded away Spikes not folded away place glasses mugs etc in the upper basket Spikes folded away more room for serv TAN ing dishes i LL 4 iN Adjusting the height of the upper basket Maximum height of the dishes in D the upper basket th
20. er safe e Plastic items that are not heat resistant by the manufacturer e Older cutlery with glued parts that are not Glazed patterns may fade if machine washed temperature resistant frequently e Bonded cutlery items or dishes e Silver and aluminium parts have a tendency to discolour during washing Residues e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver e Wooden platters immediately if it is not to be washed straight e Items made from synthetics fibres after use e Pewter or copper items e Lead crystal glass e Steel items prone to rusting Open the door and slide out the baskets to load the dishes The lower basket Load larger and heavily soiled dishes and pans in the lower basket WOWAWAAWAWH SSS SSSSCGGSSSSSS ooog se 0000 22 00 BOBO0000009 0800030000022 Load cutlery and dishes To make it easier to load larger dishes all rear plate racks in the lower basket can be folded ve down de The cutlery basket A WARNING Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp it
21. er salt or rinse aid e Load cutlery and dishes into the dishwasher Load cutlery and dishes e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Load cutlery and dishes Sponges household cloths and any object that can absorb water may not be washed in the dishwasher e Before loading the dishes you should Remove all left over food and debris Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening down wards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket e Plastic items and pans with non stick coatings have a tendency to retain water drops these items will not dry as well as porcelain and steel items e Light items plastic bowls etc must be loaded in the upper basket and arranged so they do not move BETA Load cutlery and dishes For washing in dishwasher the following cutlery and dishes are not suitable are of limited suitability e Cutlery with wooden horn china or mother Only wash stoneware in the dishwasher if it of pearls handles is specially marked as being dishwash
22. he machine is not affected Use of rinse aid A WARNING Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher clean ing agent liquid detergent This would damage the appliance i Rinse aid ensures thorough rinsing and spot and streak free drying Rinse aid is automatically added during the last rinse 1 Open the container by pressing the release button A ri NE Zi Daily use 2 Add the rinse aid in the container The maximum level for filling is indicated by max The dispenser holds about 110 ml of rinse aid which is sufficient for be tween 16 and 40 dishwashing cycles depending upon the dosage setting 3 Ensure that the lid is closed after every refill Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the dosage of rinse aid i According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum dosage position 6 maxi mum dosage The dose is factory set in position 4 Increase the dose If there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades Daily use e Check if it s necessary to refill with dishwash
23. mation about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Packaging material The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities A WARNING When a unit is no longer being used e Pull the plug out of the socket e Cut off the cable and plug and dispose of them e Dispose of the door catch This prevents children from trapping themselves inside and endangering their lives CE www electrolux com 80072 20C1L 099026211
24. meter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm max100 maximum from the bottom of the f dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided Electrical connection i i When connecting the drain hose to an under sink trap spigot the entire plastic mem A brane A must be removed Failure to re move all the membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We therefore advise you to remove it To avoid water leakage after installation make sure that the water couplings are tigh
25. ne this will avoid water drip ping from the upper basket onto the dishes in the lower one e Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes A CAUTION When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off Care and cleaning Cleaning the filters The filters must be checked and cleaned from time to time Dirty filters will degrade the washing result WARNING Before cleaning the filters ensure that the machine is switched off 1 Open the door remove the lower basket Care and cleaning 2 The dishwasher filter system compri ses a coarse filter A a microfilter B and a flat filter Unlock the filter system using the handle on the mi crofilter and remove the filter system 3 Turn the handle about 1 4 a turn an ticlockwise and remove the filter sys tem 4 Take hold of the coarse filter A by the handle with the hole and remove from the microfilter B 5 Clean all filters thoroughly under run ning water 6 Remove the flat filter from the base of the washing compartment and clean both faces thoroughly 7 Put the flat filter back in the base of the washing compartment and en sure that it fits perfectly 8 Place the coarse filter A in the mi crofilter B and press together 9 Put the filter combination in place
26. on lights illuminate The programme has been cancelled and the machine is now in setting mode First use i Before using your dishwasher for the first time e Ensure that the electrical and water connections comply with the installation instructions e Remove all packaging from inside the appliance e Set the water softener e Pour 1 litre of water inside the salt container and then fill with dishwasher salt e Fill the rinse aid dispenser If you want to use combi detergent tablets such as 3 in 1 4in 1 5 in 1 ete set the Multitab function see Multitab function Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance Set the water softener The higher the content of these minerals and salts the harder your water is Water hardness is measured in equivalent scales Clarke degrees French degrees TH and mmol l millimol per litre international unit for the hardness of water The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area Water hardness Adjusting the water hardness Use of salt setting ee Du Lane 64 88 91 125 9 1 12 5 level 10 yes 53 63 76 90 7 6 8 9 level 9 yes 46 52 65 75 6 51 7 5 2 evel 8 yes 36
27. safety instructions of the dishwasher de tergent manufacturer e The water in your dishwasher is not for drinking Detergent residues may still be present in your machine e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves e Do not sit or stand on the open door Child safety e This appliance is designed to be operated by adults Don t allow children to use the dishwasher unsupervised e Keep all packaging well away from children There is risk of suffocation e Keep all detergents in a safe place out of children s reach e Keep children well away from the dishwasher when the door is open Installation e Check your dishwasher for any transport damage Never connect a damaged machine If your dishwasher is damaged contact your supplier e All packaging must be removed before use e Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person e Forsafety reasons it is dangerous to alter the specifications or attempt to modify this product in any way e Never use the dishwasher if the electrical supply cable and water hoses are damaged or if the control panel work top or plinth area are damaged such that the inside of the appliance is freely accessible Contact your local Service Force centre in order to avoid hazard e Allsides of
28. se made quick coupling tap such as the Press block The water pressure must be within the limits given in the Technical specifications Your local Water Authority will advise you on the average mains pressure in your area The water inlet hose must not be kinked crushed or entangled when it is being connected The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut The locknut must be correctly fitted to avoid water leaks Attention NOT all models of dishwashers have fill and drain hoses provided with locknut In this case this kind of facility is not possible If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose DO NOT use connection hoses which have previously been used for an old appliance i This appliance has been fitted with safety features which will prevent the water used in the appliance from returning back into the drinking water system This appliance complies with the applicable plumbing regulations Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet spigot securing it to the underside of the work surface This will prevent waste water from the sink running into the machine 2 To a stand pipe provided with vent hole minimum internal dia
29. t Electrical connection A WARNING Safety standards require the appliance to be earthed Prior to using the appliance for the first time ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate Always plug the mains plug into a correctly installed shockproof socket Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through overheating If necessary have the domestic wiring system socket replaced In case that the electrical cable has to be replaced contact your local Service Force centre The plug must be accessible after the appliance has been installed Never unplug the appliance by pulling on the cable Always pull the plug The manufacturer accepts no liability for failure to observe the above safety pre cautions Environment concerns Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed infor
30. the dishwasher must never be drilled to prevent damage to hydraulic and electric components Product description A WARNING For electrical and water connection carefully follow the instructions given in specific paragraphs Product description Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser E Rating plate Filters E Lower spray arm EX Upper spray arm BEM Control panel Worktop Control panel o AUTO 30 INTENSIV ECO yg MATIC MIN CARE70 50 LA MULTITAB x reser L mumah e a as AUTO 30 INTENSIV ECO q MATIC MIN CARE70 50 45 a MULTITAB g On off button Programme selection buttons Delay start button Indicator lights Digital display Fl Function buttons Indicator lights Programme in progress llluminates when a washing programme is set and remains illuminated for all the duration of the washing programme MULTITAB Indicates the activation deactivation of the MULTITAB function see MULTITABfunction Control panel 9 Indicator lights Salt Illuminates when the special salt has run out g Rinse aid ___ Illuminates when the rinse aid has run out 1 BS 1 The salt and rinse aid indicator lights are never illuminated while a washing programme is running even if filling
31. with salt and or rinse aid is necessary The digital display The digital display indicates e the level of hardness to which the water softener is set e the approximate remaining time of the running programme e activation deactivation of the rinse aid dispenser ONLY with Multi tab function active e the end of a washing programme a zero will appear in the digital display e the countdown of the delay start e fault codes concerning malfunction of the dishwasher Function buttons The following functions can be set with the help of these buttons e setting of the water softener e cancel a washing programme or a delay start in progress e activation deactivation of the Multi tab function e activation deactivation of the rinse aid dispenser when Multi tab function is active Setting mode The appliance is in setting mode when ALL programme button lights are illumi nated First use i Always remember that when performing the following operations selecting a washing programme setting the water softener activating deactivating the rinse aid the appliance MUST be in setting mode If a programme button light is illuminated the last performed or selected pro gramme is still set In this case to return to setting mode the programme has to be cancelled To cancel a set programme or a programme in progress Simultaneously press and hold the two RESET buttons B and C until all the pro gramme butt
Download Pdf Manuals
Related Search