Edelbrock 65732 User's Manual
Contents
1. header 2 Re connect battery Note If your vehicle does not have an EGR install 3 At this point it is a good idea to look everything over supplied block off plate with gasket and two 5 16 bolts and lock washers kit items to header before 4 installation 8 Place header into position from below car and start 5 one bolt at front Note Use flat washers and lock washers on all bolts PARTS LIST 65732 amp 65733 Part 25 9265 25 9266 29 9245 Description Qty Manifold left side Ceramic Coated Manifold right side Ceramic Coated Manifold left side Ti Tech Coated Manifold right side Ti Tech Coated Hex header bolts 8mm x 1 25 x 30mm LS 2 V8 port gaskets Catalytic converter gasket left Catalytic converter gasket right 5 16 x 1 Hex bolts and make sure that nothing was missed in assembly Start vehicle and bring up to normal operating temperature Check for possible leaks Turn engine off and let cool Tighten all bolts again Description 3 8 16 Hex nuts 3 8 16 x 1 1 2 Hex bolts Flat washers 5 16 Lock washers 5 16 1 D x 1 8 thick Hardened washers EGR gasket A I R gasket 3 8 Lock washers EGR Block off plate Edelbrock Corporation 2700 California Street Torrance CA 90503 Toll Free Tech Line 1 800 416 8628 Tech E Mail Edelbrock Edelbrock com 2006 Edelbrock Corporation Catalog 65732 amp 65733 Page 2 of 2 Brochure 63 0405 Rev2. 7 06
3. Shorty Headers For 2000 2002 Camaro Firebird 5 7L LS1 V8 Auto Manual Transmission Catalog 65732 amp 65733 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new Tubular Exhaust System If you have any questions please contact our Technical Hotline at 1 800 416 8628 from 7 am 5 pm Monday through Friday Pacific Standard Time or e mail us at Edelbrock Edelbrock com DESCRIPTION These shorty headers are designed to improve the exhaust efficiency of the GM 5 7 Liter LS1 V8 engine This system does not require welding for installation and retains all 0 E M emissions equipment IMPORTANT NOTE Proper installation is the responsibility of the installer Improper installation will void warranty and may result in poor performance and engine or vehicle damage Suggested tools needed for installation This vehicle has some metric fasteners Q 1 4 ratchet and socket set Q 3 8 ratchet socket set with extensions and universal 13mm and 15mm swivel sockets QQ Combination of open end wrenches Q Jackstands screwdrivers pliers crescent wrench etc Q Liquid penetrant GM 1052627 or equivalent anti seize compound GM 5613695 or equivalent SPECIAL NOTICE This Edelbrock part has received an Executive Order number E 0 from the California Air Resources Board C A R B making it legal for street use on pollution controlled motor vehicles in all 50 states To assist you with emissio
4. hers then tighten evenly starting with 6 At mid section of exhaust pipe is a two bolt flange centermost bolts unbolt and set catalytic converter assembly aside Note Use flat washers and lock washers on all bolts 2006 Edelbrock Corporation Brochure 63 0405 Catalog 65732 amp 65733 Page 1 of 2 Rev 7 06 DISASSEMBLY LEF SIDE Continuation 10 7 Install 02 sensor on new manifold Use anti seize compound on threads 8 Replace spark plug wires 11 12 Install all manifold bolts and tighten Re attach EGR tube if equipped using supplied gasket and 5 16 bolts and lock washers Re attach spark plug wires Re install dip stick tube 9 Replace A I R assembly using supplied gasket 13 Re attach A I R assembly RIGHT SIDE FINAL ASSEMBLY 1 Disconnect and remove spark plug wires 1 Using supplied 3 8 16 x 1 1 2 bolts lock washers 2 Disconnect A I R assembly from manifold flat washers nut and catalytic converter flange 3 Remove bolts from EGR flange if equipped gaskets re install catalytic converter assemblies 4 Remove dip stick 2 Re install all 02 sensors use anti seize compound 5 Remove bolts from manifold 6 Remove stock manifold from below FINAL INSPECTION 7 Install flange gasket and one 8mm bolt lock washer 1 Check all hydraulic vacuum and fuel lines to ensure and flat washer at rearmost bolthole leave bolt loose there is adequate clearance to TES components enough to accept
5. ns equipment certification we have included a silver fan shroud decal to help testing personnel verify that this part is a legal replacement part on the vehicle for which it is cataloged The adhesive backed decal should be affixed to your fan shroud next to the existing emission and engine specification decal Do not cover your original equipment specification decal with the Edelbrock fan shroud decal WARNING The use of Thermal Wrap or any aftermarket coating process will void the warranty on your Tubular Exhaust System Those products can cause excessive heat and moisture build up resulting in corrosion and early failure of the system INSTALLATION INSTRUCTIONS DISASSEMBLY LEFT SIDE 1 Disconnect negative battery cable 1 Disconnect and remove spark plug wires 2 Raise vehicle and unplug all 02 sensors and carefully 2 Disconnect A I R assembly from stock manifold remove 3 Remove manifold bolts 3 Starting with the driver s side remove the three bolts 4 Remove manifold from below on the inlet flange of the catalytic converter 5 Install flange gasket and one 8mm bolt lock washer 4 At mid section of left side exhaust pipe is a two bolt and flat washer at rear most bolthole leave bolt flange unbolt and set catalytic converter aside loose enough to accept header 5 On passenger s side remove the three bolts on the 6 Place header into position from below Start all bolts inlet flange of the catalytic converter and was
Download Pdf Manuals
Related Search