Dynex DX-TVM113 User's Manual
Contents
1. 2013 BBY Solutions Inc All rights reserved DYNEX is a trademark of BBY Solutions Inc Registered in some countries All other products and brand names are trademarks of their respective owners 6907 002011 lt 02 gt V1 ENGLISH 13 03212. Minimum solid concrete thickness 8 in 203mm Minimum concrete block size 8 x 8 x 16 in 203 x 203 x 406 mm Minimum horizontal spacing between fasteners cannot be less than 16 406 mm You ll need Doc I aoe Pencil 1 2 masonry Wall plate A Drill drill bit 1 2 socket ie wrench pao C EX Wall plate template R a ape Installation instructions DX TVM113 7 TTT STEP 3 Determine whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV screen face down on a cushioned clean surface to protect the screen from damages and scratches 2 If your TV has a table top stand attached remove the stand See the documentation that came with your TV for instructions 3 Temporarily lay the TV brackets B and C on the back of your TV 4 Align the screw holes in the TV brackets with the mounting screw holes on your TV 5 Identify which type of back your TV may have Flat back The brackets lay flush against the back of your TV and do not block any jacks You do not need spacers when assembling the wall mount e Obstructed back The brackets block one or more of the jacks on the back of your TV You will need spacers when assembling the wall mount Irregularly shaped back There is a gap between a bracket and some part of the back of your TV You will need spacers when assembling the wall mount 6 Remov
3. ASSEMBLY GUIDE For wood stud solid concrete or concrete block installations Safety information and specifications Tools needed Package contents Installation instructions 00000e 2 DX TVM113 Safety information and specifications Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION Do not use this product for any purpose not explicitly specified by Dynex Improper installation may cause property damage or personal injury If you do not understand these directions or have doubts about the safety of the installation contact Customer Service or call a qualified contractor Dynex is not responsible for damage or injury caused by incorrect installation or use The weight of your TV must not exceed 100 Ibs 45 kg The wall must be capable of supporting five times the weight of your TV and wall mount combined This product contains small items that could be a choking hazard if swallowed Keep these items away from young children Tools needed You will need the following tools to assemble your new TV wall mount j p Ene Level fmm oongoD Edge to edge stud Drill finder Pencil Phillips screwdriver 7 32 5 5 mm wood drill bit Socket wrench with 1 2 for wood stud wall 13 mm socket or OR adjustable wrench Hammer 1 2 13
4. mm masonry drill bit concrete only Tape Measuring tape Package contents DX TVM113 3 TT aaa Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount A Wall Plate 1 B Left TV Bracket 1 C Right TV Bracket 1 R Wall Plate Template 1 TV Hardware Bag Label Hardware Qty Label Hardware Qty M4 x 12 mm D um screw 4 L pum sA ermm 4 M4 x 30 mm E ll OM lt crew 4 M8 x 40 mm m umm screw F M4 washer 8 N Cp M6 M8 spacers 4 G M6 M8 washer 4 o Lag bolt washer 4 H D M4 spacers 4 l M6 x 12 mm 4 P 4 screw M6 x 20 mm J pmm screw j Q Concrete anchor 4 M6 x 35 mm K mn 2 4 1 2 3 Ain 10 20 30 40 50 60 70 80 90 100mm 4 DX TVM113 Installation instructions iii CSCS Installation instructions STEP 1 Determine wall mount location Note For more detailed information on determining where to drill your holes visit our online height finder at http mf1 bestbuy selectionassistant com index php heightfinder Your T should be high enough so your eyes are level with the middle of the screen Normally 40 to 60 inches from the ground The center of your TV will match the center of the wall plate A Before you drill holes in the wall 1 Measure the distance from the bottom of your TV to the middle half of the height of the TV This is measurement a 2 Measure the distance from the floor to where you want the b
5. ay cause your TV to fall from the mount Screw is Screw is too long too short 2 Remove the screws 3 Fora flat back TV go to STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back on page 9 OR For an irregular or obstructed back go to STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs on page 10 Installation instructions DX TVM113 9 STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back 1 Align the left and right TV brackets B and C with the screw holes on the back of the TV Make sure that the brackets are level 2 Install washers F or G and screws D I J or L into the holes in the back of the TV 3 Tighten the screws until they are snug against the TV brackets Do not over tighten You ll need Screws Washers p_a m O a Level D 4 I 4 F 4 G 4 H p C J 4 L 4 B and C TV brackets Phillips screwdriver 10 DX TVM113 Installation instructions ee STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Align the left and right TV brackets B and C with the screw holes on the back of the TV Make sure that the brackets are level 2 Place spacers H or N behind the TV brackets If you are using M4 washers F place them between the spacers and TV brackets and over the h
6. e the TV brackets 8 DX TVM113 Installation instructions M SCSCSCSC SCSCSSSSSSSS STEP 4 Select screws washers and spacers 1 Select the hardware for your TV screws washers and spacers A limited number of TVs come with mounting hardware included If there are screws that came with the TV they are almost always in the holes on the back of the TV If you don t know the correct length of the mounting screws your TV requires test various sizes by hand threading the screws Select one of the following types of screws M4 x 12 mm screws D for flat backed TVs M4 x 30 mm screws E for irregular or obstructed back TVs M6 x 12 mm screws I for flat backed TVs M6 x 20 mm screws J for flat backed TVs M6 x 35 mm screws K for irregular or obstructed back TVs M8 x 16 mm screws L for flat backed TVs M8 x 40 mm screws M for irregular or obstructed back TVs Select from the following washers M4 washer F M6 M8 washer G For an irregular or obstructed TV back use the following spacers M4 spacer H M6 M8 spacer N caution To avoid potential personal injuries and property damage make sure that there are adequate threads Screw fits tO secure the brackets to your TV If you encounter resistance correctly stop immediately and contact customer service Use the shortest screw and spacer combination to accommodate your TV Using hardware that is too long may damage your TV However using a screw that is too short m
7. inal 11 2 x 31 2 in 38 x 89 mm Minimum horizontal spacing between fasteners cannot be less than 16 406 mm aeeneee Serna eras E x 2 5 in 63 5 mm You ll need 1 2 socket wrench Wall plate template R Wall plate A Edge to edge Drill 0 4 stud finder a a S p pa 7 32 wood Level Tape Pencil drill bit 6 DX TVM113 Installation instructions STEP 2 Option 2 Installing on a solid concrete or concrete block wall CAUTION 7o prevent property damage or personal injury never drill into mortar between blocks Mount wall plate directly onto the concrete surface 1 Align the wall plate template R at the height you determined in the previous step make sure that it is level then tape it into place Use a pencil to mark the lag bolt hole locations 4 Remove the wall plate template 2 Drill pilot holes to a depth of 2 5 in 63 5 mm using a 1 2 in 13 mm diameter masonry drill bit 3 Insert the concrete wall anchors Q into the pilot holes and use a hammer to make sure the anchors are flush with the concrete surface 4 Align the wall plate A with the anchors insert the lag bolts P through the lag bolt washers O then through the holes in the wall plate Tighten the lag bolts only until they are firm against the wall plate A CAUTION Avoid potential injuries or property damage DO NOT over tighten the lag bolts P
8. oles in the TV brackets If you are using M6 washers G place them over the holes in the TV brackets Insert screws E K or M through the washers TV brackets and spacers 3 Tighten the screws until they are snug against the TV brackets Do not over tighten You ll need Screws Washers Spacers i os io o Jor D or E 4 il K 4 F 8 G 4 H 4 ar ccc pue _ E level Phillips screwdriver B and CTV brackets N 4 Installation instructions DX TvM113 11 STEP 6 Mounting the TV to the wall plate 1 Place the TV brackets B and C into the slotted flanges of the wall plate A 2 Push the bottom of the TV toward the wall until the latch mechanism clicks into place E gt HEAVY You will need assistance with this step 12 DX TVM113 Installation instructions Removing the TV from the wall plate 1 Grasp the TV by the bottom edge then pull down on the locking cords and pull the bottom of the TV out from the wall 2 Release the locking cords and lift the top of the TV from the wall bracket HEAVY You will need assistance with this step Unlatched Pull down to unlatch Pull bottom away from wall then lift off the wall bracket gt A doi www dynexproducts com 800 305 2204 Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A
9. ottom of the TV to be placed on the wall Keep in mind that the bottom of the TV should be placed above any furniture such as entertainment centers or TV stands The TV should also be above items placed on top of the furniture like a Blu ray player or cable box This measurement is b 3 Add a b The total measurement is the height where you want the center of the wall plate to be on the wall 4 Use a pencil to mark this spot on the wall You ll need Measuring tape Pencil Installation instructions DX TVM113 5 a STEP 2 Option 1 Installing on a wood stud wall Note Any drywall covering the wall must not exceed 5 8 16 mm 1 Locate the stud Verify the center of the stud with an edge to edge stud finder 2 Align the wall plate template R at the height you determined in the previous step make sure that it is level then tape it into place Use a pencil to mark the lag bolt hole locations 4 on the stud centers Remove the wall plate template 3 Drill pilot holes to a depth of 2 5 in 63 5 mm using a 7 32 in 5 5 mm diameter drill bit 4 Align the wall plate A with the pilot holes insert the lag bolts P through the lag bolt washers O then through the holes in the wall plate Tighten the lag bolts only until they are firm against the wall plate A CAUTION Avoid potential injuries or property damage DO NOT over tighten the lag bolts P Minimum wood stud size common 2 x 4 in 51 x 102 mm nom
Download Pdf Manuals
Related Search