Dynalink A 0977A User's Manual
Contents
1. per the codes list to the highest code number and will stop searching when it has done all code numbers as per your selected key no in fig 1 Note 2 During searching you may release 1 button j PANASONIC HITACHI TOSHIBA PIONEER SANYO MITSUBISHI AKAI FUJITSU PHILIPS THOMSON EMRSON PANASONIC HITACHI NEC TOsHIBA PIONEER SHARP SANYO MITSUBISHI PHILIPS THOMSON PANASONIC HITACHI NEC TOSHIBA PIONEER SHARP SANYO MITSUBISHI PHILIPS THOMSON EMRSON LOEWE APEX TEAC PANASONIC HITACHI NEC TOSHIBA PIONEER SHARP SANYO MITSUBISHI JVC AKAI FUJITSU SAMSUNG PHILIPS THOMSON EMRSON LOEWE SONY ONKYO DENON KENWOOD PANASONIC HITACHI NEC TOSHIBA PIONEER SHARP SANYO MITSUBISHI PHILIPS JERROLD TEAC 7 B MAGNAVOX MARANTZ MARANTZ MARANTZ ECHOSTAR TECHNICS TECHNICS GENERAL FISHER YAMAHA Figure 1 This table shows the number left column corresponding to different popular device brands TEAC MARANTZ GENERAL TECHNICS FISHER ECHOSTAR TECHNICS FISHER YAMAHA SYLVANIA SYLVANIA E Using TV quick search For TV programming Press TV device key and release Turn on TV using your existing remote Press and hold MUTE button After 3 seconds it will begin searching Every second it will send 15 codes to the TV The LED indicator will flash fast indicating it is sending the codes 4 When the TV displays MUTE release2. the mute button The LED indicator will now flash twice every 2 seconds 5 When the TV displays VOL quickly press the OK button to save the code The LED indicator will extinguish Note 1 Every quick search will begin from the last code sent until it has completed one circle of codes on F Using LEARNING mode to program the remote control 1 Press and hold the device key The LED indicator will flash once Press and hold the LEARN key for 3 seconds The LED indicator will flash continuously 2 Release the LEARN button 3 Place the original remote and the A 0977A remote control as per the diagram below with a distance apart of 1 2cm Original Remote Jumbo Learning Remote 4 Press once the function button you want to learn on the A 0977A universal remote The LED indicator will illuminate and remain lit Press and hold the original remote function button you want to program The LED will now remain constantly on Press and hold the button on your original remote that you want to learn The LED will flash twice and then change to flashing very quickly The button has now been learnt Release the button on your original remote If the remote control codes data from your original remote has not been successfully learnt the LED indicator will blink 3 times and remain constantly lit waiting for data to be received again from your original remote To learn the function please repeat step 4 5 To learn other button
3. A 0977A A Learning Jumbo Remote gt ynaink Operating Instructions Congratulations on purchasing the A 0977A 4 in 1Jumbo remote control The unit can program a range of devices including TVs Set top boxes DVDs amplifiers VCRs PVRs CDs etc For the full range of compatible devices refer to the device code listing enclosed with this product The remote control has 4 labelled device keys These are TV STB Set top box DVD and AUX Auxiliary However any type of device can be programmed into any button Instructions Install batteries in unit batteries not supplied requires 2 x AA cells The battery compartment is on the rear of the unit Insert batteries in direction indicated in battery compartment Code Programming The unit can be programmed in the following ways A Inputting the brand code number 1 Press and hold the device key button you want to program eg TV STB etc for 3 seconds until the LED indicator remains illuminated 2 Release the device key 3 Locate the brand code number from the code list supplied separately with this unit Eg Akai 0043 0067 0070 etc Now input this code Once entered the LED will turn off 4 If you input an incorrect code the LED indicator will flash twice If this occurs simply go back to step 1 5 Test the operation of the remote control If the first code for the designated appliance eg Akai 0043 does not work or some functions do not work correctly enter the next ap
4. mote control to the appliance Press the Power button and release and the remote control will send a power off signal to your device every 2 seconds 5 When the remote control finds the correct device type by powering off your device press the OK button The LED indicator will no longer be illuminated Note 1 Every time you begin the autosearch it will begin searching from the last code Once the unit has outputted every code the LED indicator will extinguish and quit searching Hence it may be necessary to start the search again from the beginning Note 2 During searching you may press LEFT search backwards or RIGHT button search forwards Note 3 You can use MUTE button instead of the Power button to find the code for your device When the code is found the mute function will be enabled D Using popular brand name code search 1 Turn on device eg TV using your existing remote 2 Press and hold the device key Whilst holding the device key press the number that corresponds to your device brand as per the chart Fig 1 page 3 Continue holding the 2 buttons on 2 Turn on device eg TV 3 The remote control will now send a power off signal to your device every 2 seconds The LED indicator will flash every 2 seconds denoting it is sending the code to your device 4 When your device powers off release the 2 buttons Note 1 The searching begins from the lowest code number as
5. pliance code eg Akai 0067 until you are successful The device key code number can be checked as follows 1 Press and hold the device key name you want to display eg TV 2 The LED indicator will flash once 3 Whilst holding the device key press the OK button then release both buttons 4 The LED indicator will now flash the number of times that corresponds to each digit of the code with a 1 second pause between each digit 5 For example if the code is 1038 the indicator will flash once stop for 1 second flash 10 times for the 0 pause for a second flash 3 times for the 3 then flash 8 times for the g 6 When finished the remote control will exit automatically 1 B Using Code manual search 1 Press and hold the device key button you want to program eg TV STB etc for 3 seconds until the LED indicator remains illuminated 2 Release the device key 3 Turn on device eg TV using your existing remote 4 Face the remote control to the appliance Press and release the left or right button Each pressing of the button sends a different Off command to the appliance Repeat this action until the TV powers Off 5 Press the OK button C Using Auto Code search 1 Press and hold the device key button you want to program eg TV STB etc for 3 seconds until the LED indicator remains illuminated 2 Release the device key 3 Turn on device eg TV using your existing remote 4 Face the re
6. s repeat step 4 until you have completed all buttons 6 Press LEARN key again to quit learning mode NOTE 1 When you enter Learning mode if you do not press any button within 15 seconds the unit will exit learning mode NOTE 2 If you are in Learning mode and no remote control codes data from another remote control 4 are received within 15 seconds the unit will exit learning mode NOTE 3 Except LEARN and device buttons any button can be programmed and programmed more than once The unit will retain the last code programmed To delete any programmed buttons 1 Press the device key 2 Press and hold the learn button then press the device button you wish to clear After 2 seconds The LED indicator will flash 3 times signifying the data has been deleted To delete all the data in a device key Press and hold the Learn button then press MUTE button After 2 seconds the LED indicator will flash 3 times and all the learned data will be deleted To reset the remote Go into code programming mode see A Inputting the brand code number When in programming mode input the device key 9901 The LED indicator will flash twice and the remote will go back to its original factory preset
Download Pdf Manuals
Related Search