Dual XDM6220 User's Manual
Contents
1. GRAY BLUE BLACK RED 10 AMP dived p YELLOW Right Front o Gray Black Gray 7 Left Front White Black White id Rear Preamp Output Connect to amplifier input Remote Turn On Connect to amplifier or power antenna Insulate wire if not used Ground Connect to vehicle chassis ground Accessory aa 0 Connect to existing ignition circuit or switched 12 volt source 0 LH Memory Connect to battery circuit or constant 12 volt source Right Rear Violet Black o Violet Li o Left Rear 0 Green Black o Green Antenna Connector plug Interface Cable included Connect to audio output of portable media player etc not included FUSE When replacing the fuse make sure new fuse is the correct type and amperage Using an incorrect fuse could damage the radio The XDM6220 uses one 10 amp AGC fuse Battery located in line XDM6220 OPERATION Control Locations Release Power Mute Audio Band Play Pause Auto Store Preset Scan Enter Mode Search Eject Tune Track Up Down Loudness Display 0 00900000000 m o Ss o Tuner Scan 8 Local Distance 7 Preset 6 Folder Up Preset 5 Folder Down Preset 4 Preset 3 Intro Preset 2 Random Preset 1 Repeat Volume Up Down The XDM6220 allows playback of your favorite2. XDM6220 INSTALLATION OWNER S MANUAL AM FM CD MP3 WMA Receiver with Detach Face COMPACT RECORDABLE REWRITABLE Dplug XDM6220 INSTALLATION Preparation Please read entire manual before installation Before You Start Disconnect negative battery terminal consult a qualified technician for instructions Avoid installing the unit where it would be subject to high temperatures such as from direct sunlight or where it would be subject to dust dirt or excessive vibration Getting Started Remove 2 transit screws located on top of the unit Insert the supplied keys into the slots as shown and slide the unit out of the mounting sleeve Install mounting sleeve into opening bending tabs to secure TRIM RING Connect wiring harness and antenna consult a qualified technician if you are unsure Certain vehicles may require an installation kit and or wiring harness adapter sold separately Test for correct operation and slide into mounting sleeve to secure Snap trim ring into place Mount the iplug adapter to any smooth clean surface using the supplied double sided tape or 2 x 3 8 Phillips head screws MOUNTING STRAP HEX NUT PLAIN WASHER HEX BOLT SPRING WASHER TAPPING SCREW T MOUNTING SLEEVE TYPICAL FRONT LOAD DIN MOUNTING METHOD XDM6220 INSTALLATION Wiring Diagram YELLOW Auxiliary Input HHAH ULU
3. on display ERROR 02 appears Focus error or disc is in upside down Press EJECT or RESET on display ERROR 03 appears FAT error Press EJECT or RESET on display ERROR 04 appears MP3 WMA decode error Press EJECT or RESET on display PROTECT appears The WMA file is DRM protected Press EJECT or RESET on display Unit will not accept CD mechanism position out of alignment Press EJECT for 3 seconds to reset a disc CD mechanism position CD transit screws still in place Remove 2 transit screws located on top of the unit XDM6220 OPERATION Dual Notes Dual Electronics Corp 21318 64th Ave South Kent WA 98032 Toll Free 1 866 382 5476 www dualav com 2005 Dual Electronics Corp All rights reserved Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries NSA0505 V01
4. MP3 WMA Files Folder Access File Repeat File Repeat Current Folder Only Disc Random Folder Random Disc Intro Folder Intro Press FY to select the previous folder Press FA to select the next folder Folder access is only available on MP3 WMA discs recorded with more than one folder Press RPT momentarily to continuously repeat selected file Press RPT again to cancel Press RPT for more than 2 seconds to consecutively repeat all files in the current folder only The S icon will appear in the display when in folder repeat mode Press RPT again to cancel Press RDM momentarily to play all files on entire disc in random order Press RDM again to cancel Press RDM for more than 2 seconds to play all files in current folder only in random order The fa icon will appear in the display when in folder random mode Press RDM again to cancel Press INT momentarily to play the first 10 seconds of each file on the entire MP3 WMA disc Press INT again to cancel Press INT for more than 2 seconds to play the first 10 seconds of each file in the current folder only The fm icon will appear in the display when in folder intro mode Press INT again to cancel Note File repeat current folder only folder random and folder intro is only available on MP3 WMA discs recorded with more than one folder XDM6220 OPERATION CD Player Operation MP3 WMA Files Media Compatibility Playback Order Compatible Re
5. MP3 WMA Files Additional MP3 WMA Information Sampling Frequency Rates MP3 WMA Transfer Bit rates MP3 WMA MP3 Tag Display Recommended Settings An internal buffer provides ESP Electronic Skip Protection to virtually eliminate skipping When playing a disc recorded with regular audio files CD DA or WAV and MP3 WMA files the unit will play the MP3 WMA files only Only MP3 files with filename extension mp3 can be played Only WMA files with filename extension wma can be played Do not attempt to play discs which contain non MP3 WMA files with the MP3 WMA extension 8kHz 48kHz 32kHz 48kHz 8kbps 320kbps constant Variable bit rates 32kbps 192kbps constant Variable bit rates Note Some files may not play or be displayed correctly depending on sampling rates and bit rates ID3 tags Version 1 x This model will not display ID3 Version 2 0 or greater tags For best results use the following settings when burning an MP3 disc 128kbps or higher constant bit rate 44 1kHz or higher sampling frequency For best results use the following settings when burning a WMA disc 64kbps or higher constant bit rate 32kHz or higher sampling frequency XDM6220 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights You may also have other rights which vary from state to state Dual Electronics Corp warrants this product to the original purchaser to be free fro
6. Press and hold DISP then press TUNE lt lt to select time display priority TIME will momentarily appear in the display Clock will be displayed by default Radio frequency CD track elapsed time or MP3 WMA file information is accessed by pressing DISP momentarily Programs unit to display clock no clock when unit is off Press and hold MODE then press PRESET 1 to select clock priority on off CLK ON or CLK OFF will momentarily appear in the display Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs The reset button is located behind the faceplate Refer to page 2 for details Press and hold AUD for 3 seconds to turn confirmation beep on off BEEP ON or BEEP OFF will momentarily appear in the display Press MUTE to silence the audio MUTE will flash in the display Press MUTE again to cancel Audio Bass Treble Balance Fader Source Audio Memory XDM6220 OPERATION General Operation Press AUD to select between Volume default Bass Treble Balance amp Fader BAS TRE BAL gt FAD 7 Press AUD until BAS appears Press VOL V or A to adjust 6 minimum 6 maximum Press AUD until TRE appears Press VOL V or A to adjust 6 minimum 6 maximum Press AUD until BAL appears Press VOL V or A to adjust BAL L 12 BAL 00 BAL R 12 BAL 00 represents equal balance Press AUD until FAD appears Press VOL
7. the display Use the buttons in the table on page 11 32 character maximum input or the VOL Y VOL A to enter the desired alphanu meric search characters Press AUD to advance one character to the right Press to initiate the selected alphanumeric search Press VOL V VOL A to preview the search results If the search returns a folder the asi icon will illuminate Press to select the desired file or folder If a folder is selected two will illuminate Press VOL A to begin searching files in the folder Press to select the desired file within the folder Note If the file is not available NO FILE will be displayed momentarily and the current file will continue to play Press SEARCH for more than 3 seconds then release Press SEARCH again two times to navigate files folders on the disc The current folder name will scroll one time followed by available files and folders Press VOL V VOL A to preview files folders in the current folder If a folder is selected the fais icon will illuminate Press to select the desired file or folder If a folder is selected two will illuminate Press VOL A to begin searching files in the folder Press to select the desired file within the folder When navigating root folders will illuminate Press AUD to access the previous folder level up one level Only available on MP3 WMA discs recorded with more than one folder XDM6220 OPERATION CD Player Operation
8. 1710kHz Usable sensitivity 22uV Frequency response 30Hz 2 2kHz Total power output 200 Watts Peak Power output 50Wx4 4 ohms 14 4 VDC Operating voltage 11 16 VDC negative ground Speaker output impedance 448 ohms Line output voltage 2 Volts Dimensions 7 x 7 x 2 178 x 178 x 51 mm Design and specifications subject to change without notice XDM6220 WARRANTY Troubleshooting Problem Unit will not turn on no power Cause Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Action Check connections for proper voltage 11 16VDC Black wire not connected Check connection to ground Fuse blown Replace fuse Unit has power but no sound Speaker wires not connected Check connections at speakers One or more speaker wires touching each other or touching chassis ground Insulate all bare speaker wires from each other and chassis ground Unit blows fuses Yellow or red wire touching chassis ground Check for pinched wire Speaker wires touching chassis ground Check for pinched wire Incorrect fuse rating Use fuse with correct rating Excessive skipping Unit is not mounted correctly or backstrap is not secure Check mounting sleeve and backstrap support Physical defect in media CD CD R or CD RW Check media for scratches ERROR 01 appears Disc read error Press EJECT or RESET
9. CK gt gt to skip to the beginning of the next track Press TRACK lt lt to return to the beginning of the current track Pressing TRACK lt lt again skips to the beginning of the previous track Press and hold TRACK gt gt or TRACK lt lt to fast forward or reverse a track Press amp Il to temporarily stop CD playback Press amp Ill again to resume playback Press INT to play the first 10 seconds of each track Press INT again to cancel Press RPT to continuously repeat selected track Press RPT again to cancel Press RDM to play all tracks in random order Press RDM again to cancel Random mode is retained in memory when selecting between tuner CD player and auxiliary input modes and when the unit is turned on off Some CD Rs and CD RWs may be incompatible with this unit depending on media type and recording method In addition the following CDs may be incompatible with this unit CDs exposed to extreme temperatures or direct sunlight for extended periods of time CDs recorded in which a recording session failed or a re recording was attempted and or encrypted or copy protected CDs which do not conform to the audio CD DA red book recording standard XDM6220 OPERATION CD Player Operation MP3 WMA Files Playing an MP3 WMA Disc ws MP3 Icon i WMA Icon fa Folder Icon Displaying Information Character Support When an MP3 WMA encoded disc is first inserted READING will a
10. M1 FM2 FM3 AM1 and AM2 bands Press and hold BAND then press TUNE lt lt to select European frequency spacing Press and hold BAND then press TUNE gt gt to select USA frequency spacing default Up to 18 FM stations and 12 AM stations can be stored To store a station select the desired band and station Press and hold the desired preset button 1 6 for more than 2 seconds When stored the preset number will appear in the display The station can be recalled anytime by pressing the corresponding preset button Note Function buttons 7 8 9 and 0 apply to MP3 and WMA playback only Press AS PS for more than 2 seconds to automatically store the six strongest stations in the current band Automatic LocaUDistance is activated during the initial band scan Press AS PS for less than 2 seconds to scan presets 1 6 on the current band pausing for 5 seconds at each Press AS PS again to cancel Insert CD Eject CD Track Select Fast Forward and Reverse Pause Intro Repeat Random CD R CD RW Compatibility XDM6220 OPERATION CD Player Operation With the label facing up insert a standard size CD into the CD slot The CD will automatically begin playback Press EJECT to eject the CD The unit will change to previous mode of operation AM FM or auxiliary input If the disc is not removed within 10 seconds the unit will reload the disc The unit does not have to be turned on to eject CD Press TRA
11. MP3 and WMA files recorded on CD R and CD RW discs Its powerful on board DSP processor decodes the compressed audio while maintaining near CD sound quality An internal SRAM buffer provides ESP Electronic Skip Protection to virtually eliminate skipping and allows alphanumeric or direct track search even while a song is currently playing 4 Faceplate Removal Semi permanent Faceplate Installation Power On Off Mode Loudness Volume Programmable Turn On Volume Preset EQ Curves Display Set the Clock 12 24 hour Clock XDM6220 OPERATION General Operation Press RELEASE and pull away from the left side to remove To re install insert right side of faceplate first then push left side to secure Remove trim ring and install supplied 1 x 7 32 Phillips head screw through left side of mounting frame into faceplate Press PWR or any other button except eject or volume up down to turn the unit on Inserting a disc will turn the unit on automatically Press PWR to turn the unit off Press MODE to select between tuner CD player and auxiliary input Modes of operation are indicated in the display Press LOUD to activate and deactivate the loudness contour curve Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes Adjust volume using VOL W VOL A 00 46 Press and hold PWR for 3 seconds to program currently selected volume level P VOL and t
12. V or A to adjust FAD F 12 FAD 00 FAD R 12 FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM FM CD and AUX modes This allows you to save the Bass and Treble settings separately for each mode Example FM tuner mode can have Bass 3 and Treble 1 while CD mode can have Bass 2 and Treble 2 Note Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve if one is selected XDM6220 OPERATION Tuner Operation Seek Tuning Manual Tuning Scan Tuning Local Distance Band Frequency Spacing Storing and Recalling Station Presets Automatically Store Stations Preset Scan Press TUNE lt lt or TUNE gt gt momentarily to seek the next strong station Press TUNE lt lt or TUNE gt gt for more than 2 seconds then release MANUAL will momentarily appear in the display Press TUNE lt lt or TUNE gt gt momentarily to move radio frequency up or down one step at a time Press and hold to advance quickly If tuning is not adjusted for 5 seconds the unit will return to seek tuning mode default AUTO will momentarily appear in the display Press SCAN to preview strong stations on the current band pausing for 5 seconds at each Press SCAN again to cancel Press LOC to activate local tuning for strong station reception only Press LOC again to cancel and resume distance tuning default Press BAND to select between F
13. cording Formats The following types of discs files are compatible CD ROM ISO CD R CD RW CD DA MP3 data WMA data The following types of discs files are not compatible WMA files that are protected by DRM Digital Rights Management WMA lossless format Discs recorded with Track At Once or packet writing MP3 PRO format MP3 playlists WAV format MP3 WMA playback sequence is based on recorded order of files and begins in the root folder of the disc Any empty folders or folders that do not include MP3 WMA files are skipped This unit may not play files in the order they were recorded in Refer to your recording software s user s manual for more information e S09660 level 1 e S09660 level 2 Yellow Book MODE 1 Yellow Book MODE 2 FORM 1 Multi session Maximum folders and files 256 Maximum folder levels 8 MPEG 1 2 2 5 Audio Layer 3 1509660 standards Maximum nested folder depth is 8 including the root folder Valid characters for folder file names are letters A Z all caps numbers 0 9 and _ underscore Some characters may not be displayed correctly depending on the character type This device can play back discs in Joliet Romeo and other standards that conform to IS09660 MP3 WMA written in the formats other than the above may not play and or their file names or folder names may not be displayed properly XDM6220 OPERATION CD Player Operation
14. he current volume level will momentarily appear in the display Press EQ to select between POP JAZZ CLASSIC BEAT ROCK and OFF default equalization curves Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve if one is selected Press DISP to select between clock and radio frequency tuner mode clock and CD track elapsed time CD mode or clock and AUX AUX mode With the unit on press and hold DISP until the clock begins to flash then release Press TUNE to adjust the hours and TUNE gt gt to adjust the minutes Press DISP momentarily to save the selected time The clock will display 12 hour AM PM time in USA frequency spacing mode PM 10 00 In European frequency spacing mode the clock will display 24 hour time 22 00 XDM6220 OPERATION General Operation Programmable Display Priority Programmable Clock Priority Reset Confirmation Beep Mute In tuner mode press and hold DISP then press TUNE gt gt to select function priority display FREQ will momentarily appear in the display Note FUNC will appear in CD or AUX modes Radio frequency tuner mode CD track elapsed time CD mode or AUX AUX mode will be displayed by default Note When playing MP3 WMA files the track number elapsed time track name directory name title artist album year or comment will be displayed by default Clock is accessed by pressing DISP momentarily
15. ion with a copy of the original receipt from the retailer to an authorized service center 3 Please describe your problem in writing and include your name a return UPS shipping address P O Box not acceptable and a daytime phone number with your shipment 4 For more information and for the location of the nearest authorized service center please contact us by one of the following methods Call us toll free at 1 866 382 5476 Email us at cs dualav com Exclusion of Certain Damages This warranty is exclusive and in lieu of any and all other warranties expressed or implied including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation liability right claim or remedy in contract or tort whether or not arising from the company s negligence actual or imputed No person or representative is authorized to assume for the company any other liability in connection with the sale of this product In no event shall the company be liable for indirect incidental or consequential damages CD Player FM Tuner AM Tuner General XDM6220 OPERATION Specifications Signal to noise gt 92dB Frequency response 10Hz 20kHz Channel separation 1kHz gt 65dB D A converter 1 Bit Tuning range 87 5MHz 107 9MHz Usable sensitivity 8 5dBf 50dB quieting sensitivity TOdBf Stereo separation 1kHz 40dB Frequency response 30Hz 13kHz Tuning range 530kHz
16. m defects in material and workmanship for a period of one year from the date of the original purchase Dual Electronics Corp agrees at our option during the warranty period to repair any defect in material or workmanship or to furnish an equal new renewed or comparable product whichever is deemed necessary in exchange without charges subject to verification of the defect or malfunction and proof of the date of purchase Subsequent replacement products are warranted for the balance of the original warranty period Who is covered This warranty is extended to the original retail purchaser for products purchased and used in the U S A What is covered This warranty covers all defects in material and workmanship in this product The following are not covered installation removal costs damage resulting from accident misuse abuse neglect product modification improper installation incorrect line voltage unauthorized repair or failure to follow instructions supplied with the product or damage occurring during return shipment of the product What to do 1 Before you call for service check the troubleshooting guide in your owner s manual A slight adjustment of any custom controls or connections discussed in your instruction booklet may save you a service call 2 If you require service during the warranty period you must carefully pack the product preferably in the original package and ship it by prepaid transportat
17. n function table when selecting searching or navigating MP3 WMA files and folders MP3 WMA Button Function Table SEARCH Direct Select Search and Navigate Modes Enter Confirm Preset 1 A B C 1 Preset 2 D E F 2 Preset 3 G H 1 3 Preset 4 JKL 4 Preset 5 Preset P Q R6 S T U 7 V W X 8 Y Z 9 T 0 AUD Character Shift VOLw VOLA Character Select A B C 8 9 0 MUTE Character Backspace Direct Select Search and Press SEARCH for more than 3 seconds to select between Navigate Modes the following modes Direct File Select Alphanumeric File or Folder Search File or Folder Navigate Direct File Select Press SEARCH for more than 3 seconds then release Step 1 MP3 T or WMA T will flash in the display Use the buttons in the above table 3 keystroke maximum input or the VOL V VOL A to enter the desired file number Step2 Press to confirm the selected file number or wait for the input cycle to time out approximately 5 seconds If the file is not available NO FILE will be displayed momentarily and the current file will continue to play XDM6220 OPERATION CD Player Operation MP3 WMA Files Alphanumeric File or Folder Search Step 1 Step 2 Step 3 Step 4 Step 5 File Folder Navigate Step 1 Step 2 Step 3 Step 4 Folder Access Up one level 12 Press SEARCH for more than 3 seconds then release Press SEARCH again an will flash in
18. ppear in the display Depending on the number of files and folders this may take several seconds The es icon will illuminate anytime a valid MP3 encoded disc is inserted and flash in MP3 search navigate modes The m icon will illuminate anytime a valid WMA encoded disc is inserted and flash in WMA search navigate modes The amp icon will illuminate anytime a folder is selected in the file folder search modes Press DISP to select between track number elapsed time default clock track name directory name title artist album year and comment NO ID3 TAG will be displayed if the MP3 file contains no ID3 tag information UNKNOWN will be displayed if the WMA file contains no WMA tag information ROOT will be displayed if the directory name of a root folder is not labeled Maximum character display information Track name 32 character maximum e Directory name 32 character maximum e Song title 30 character maximum e Artist name 30 character maximum e Album name 30 character maximum Year 4 character maximum e Comment 28 character maximum Song title Artist Name Album name Year and Comment will only be displayed if included with the MP3 WMA file When referring to MP3 WMA playback the following terms are synonymous File name and track name Folder name and directory name XDM6220 OPERATION CD Player Operation MP3 WMA Files Refer to the following butto
Download Pdf Manuals
Related Search