Dual XD622W User's Manual
Contents
1. RCA Cable sold separately GRAY Rear Preamp Output Connect to amplifier RCA Input BLUE Remote Turn On Connect to amplifier or power antenna Insulate wire if not used M BLACK Ground Connect to vehicle chassis ground RED Accessory lt 0 Connect to existing ignition circuit or switched 12 volt source FUSE When replacing a fuse 7 make sure new fuse is the correct type and amperage YELLOW Memory Using an incorrect fuse Connect to battery could damage the radio circuit or constant 12 volt source The XD622W uses one 10 amp ATM fuse located beside the wiring connector Right Front Right Rear Gray Black Violet Black Gray Violet Y Left Front Left Rear White Black Green Black White Green 9 XD622W OPERATION Control Locations XDGZZW CD WEATHER RECEIVER 208 WATTS GD CLASSIC BEAT OCR 0651 0 Release Mode Power Bass Boost Audio Preset 6 Scan Preset 5 Display Preset 4 Auto Store Preset Scan Preset 3 CD Intro EQ Preset 2 CD Random Tune Track Down Preset 1 CD Repeat Play Pause Band Mute Eject Tune Track Up 1 99 Semi permanent For semi permanent faceplate installation remove trim ring Faceplate Attachment and install supplied Phillips head 1 screw through left side2. 22 CO WEATHER AECEIVER 8 6208 WATTS R cmm pR Wise SCAN mses 57 INPUT mone XD622W INSTALLATION OWNERS MANUAL AM FM CD Weather Receiver XD622W INSTALLATION Preparation Please read entire manual before installation Before You Start e Disconnect negative battery terminal consult a qualified technician for instructions e Avoid installing the unit where it would be subject to high temperatures such as from direct sunlight or where it would be subject to dust dirt or excessive vibration Getting Started Remove 2 transit screws located on top of the unit Insert the supplied keys into the slots as shown and slide the unit out of the mounting sleeve Install mounting sleeve into opening bending tabs to secure e Connect wiring harness and antenna consult a qualified technician if you are unsure Certain vehicles may require installation kit and or wiring harness adapter sold separately Test for correct operation and slide into mounting sleeve to secure Snap trim ring into place HEX BOLT MOUNTING SLEEVE TYPICAL MOUNTING METHOD HEX NUT PLAIN WASHER SPRING WASHER TAPPING SCREW XD622W INSTALLATION Wiring Diagram og YELLOW Auxiliary Input
3. are erased Up to 18 FM stations and 12 AM stations can be stored To store a station select the desired band and station Press and hold the desired preset button for more than 2 seconds When stored the preset number will appear in the display The station can be recalled anytime by pressing the corresponding preset button Press AS PS for more than 3 seconds to automatically store the six strongest stations in the current band Automatic Local Distance is activated during the initial band scan Press AS PS to scan presets 1 6 on the current band pausing for 5 seconds at each Press AS PS again to cancel XD622W OPERATION Weatherband Tuner Operation Manual Tuning Press TUNE 3 25 momentarily to seek the next weatherband station Direct Tuning Press preset 1 6 or BAND to directly access the 7 weatherband stations Refer to the table below Weatherband Stations Direct Tuning Table Preset 1 162 400 MHz Wb 1 Preset 2 162 425 MHz Wb 2 Preset 3 162 450 MHz Wb 3 Preset 4 162 475 MHz Wb 4 Preset 5 Wb 5 Preset 6 162 525 MHz Wb 6 BAND 162 550 MHz Wb 7 Insert CD Eject CD Track Select Fast Forward and Reverse Pause Intro Repeat Random CD R Compatibility XD622W OPERATION CD Player Operation With the label facing up insert a standard size CD into the CD slot The CD will automatically begin playback Press the EJECT button to stop and eject the CD The unit wi
4. abuse neg lect product modification improper installation incorrect line voltage unauthorized repair or failure to follow instructions supplied with the product or dam age occurring during return shipment of the product What to do If the product requires warranty service you must prepay the initial shipping charges DUAL will pay the return shipping charges if the product is returned to an address within the USA Namsung America Inc Attn Returns Center 21318 64th Ave South Kent WA 98032 U S A Toll Free 1 866 626 7863 Exclusion of Certain Damages This warranty is exclusive and in lieu of any and all other warranties expressed or implied including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation liability right claim or remedy in contract or tort whether or not arising from the company s negligence actual imputed No person or representative is authorized to assume for the company any other liability in connec tion with the sale of this product In no event shall the company be liable for indirect incidental or conse quential damages Specifications Outside Diameter Mounting Depth Mounting Height Cut out Diameter Frequency Response Sensitivity Impedance RMS Power Peak Power DMP65 SPECIFICATIONS 7 13 2 5 88 5 13 45Hz 18kHz 3dB 90dB 1W 1M 4 ohms 20 Watts 60 Watts Specifications subject to change with
5. ad Eject operation error Press eject or RESET ERO3 appears on display Focus adjustment error Clean or replace media 04 appears on display Tracking auto adjustment error Clean or replace media 6 appears on display Sled operation error Press eject or RESET ERO7 appears on display Focus error or disc is in upside down Press eject or RESET 8 appears on display CLV PLL operation error Press eject or RESET 9 appears on display TOC data read error Clean or replace media Namsung America Inc 21318 64th Ave South Kent WA 98032 Toll Free 1 866 626 7863 www dualav com 2004 Namsung America Inc EVOK0404 V01 DMP65 INSTALLATION OWNERS MANUAL 6 5 Dual Cone Marine Speakers MARINE DMP65 INSTALLATION Preparation Installation Please read entire manual before installation Before You Start Disconnect negative battery terminal consult a qualified technician for instructions e Use extreme caution when drilling holes to avoid damaging fuel lines hydraulic lines or existing wiring Getting Started Determine where the speakers will be mounted Ensure an area large enough for the speaker to mount evenly Be sure the mounting location is deep enough for the speaker to fit e Using an appropriate tool cut a 5 13 diameter mounting hole Route speaker wires and connect to speakers observing speaker polarity e Ins
6. ation with proof of the purchase date from the retailer to the Return Center address listed below 3 Please describe your problem in writing and include your name a return UPS shipping address Box not acceptable and a daytime phone number with your shipment 4 DUAL will pay the return shipping charges if the product is returned to an address within the USA Namsung America Inc Attn Returns Center 21318 64th Ave South Kent WA 98032 U S A Toll Free 1 866 626 7863 Exclusion of Certain Damages This warranty is exclusive and in lieu of any and all other warranties expressed or implied including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation liability right claim or remedy in contract or tort whether or not arising from the company s negligence actual or imputed No person or representative is authorized to assume for the company any other liability in connection with the sale of this product In no event shall the company be liable for indirect incidental or consequential damages CD Player FM Tuner AM Tuner Wetherband Tuner General XD622W OPERATION Specifications Signal to noise gt 92dB Frequency response 10Hz 20kHz Channel separation 1kHz gt 65dB D A converter 1 Bit Tuning range 87 5MHz 107 9MHz Usable sensitivity 8 5dBf 50dB quieting sensitivity 10dBf Stereo separation 1kHz 40dB Frequency r
7. esponse 30Hz 13kHz Tuning range 530kHz 1710kHz Usable sensitivity 22uV Frequency response 30Hz 2 2kHz Tuning range 162 400MHz 162 550MHz Total power output 208 Watts Peak Power output 52Wx4 4 ohms 14 4 VDC Operating voltage 11 16 VDC negative ground Speaker output impedance 4 8 ohms Line output voltage 2V Dimensions 7 x 7 x 2 178 x 178 x 51 mm Design and specifications subject to change without notice XD622W OPERATION Troubleshooting Problem Unit will not turn on no power Cause Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Action Check connections for proper voltage 11 16VDC Black wire not connected Check connection to ground Fuse blown Replace fuse Unit has power but no sound Speaker wires not connected Check connections at speakers One or more speaker wires touching each other or touching chassis ground Insulate all bare speaker wires from each other and chassis ground Unit blows fuses Yellow or red wire touching chassis ground Check for pinched wire Excessive skipping Speaker wires touching chassis ground Incorrect fuse rating Unit is not mounted correctly or backstrap is Check for pinched wire Use fuse with correct rating Check mounting sleeve and backstrap not secure support Physical defect in media CD or CD R Check media for scratches ER02 appears on display Lo
8. ll change to previous mode of operation AM FM tuner Weatherband tuner or auxiliary input If the disc is not removed within 10 seconds the unit will reload the disc The unit does not have to be turned on to eject CD Press TRACK 2 to skip to the beginning of the next track Press TRACK 3 to return to the beginning of the current track Pressing TRACK again skips to the beginning of the previous track Press and hold TRACK 2 or TRACK 5 to fast forward or reverse a track Press to temporarily stop CD playback Press again to resume playback Press INT to play the first 10 seconds of each track Press INT again to cancel Press RPT to continuously repeat selected track Press RPT again to cancel Press RDM to play all tracks in random order Press RDM again to cancel Random mode is retained in memory when selecting between modes and when the unit is turned on off Some CD Rs may be incompatible with this unit depending on media type and recording method This model does not support CD RWs XD622W WARRANTY Limited One Year Warranty This warranty gives you specific legal rights You may also have other rights which vary from state to state Namsung America Inc warrants this product to the original purchaser to be free from defects in material and workmanship under normal conditions for a period of one year from the date of the original purchase Namsung America agrees at our option during
9. ntil clock begins to flash then release Press TUNE 2 to adjust the hours and TUNE amp to adjust the minutes Press DISP momentarily to save the selected time The clock will display 12 hour AM PM time in U S frequency spacing mode PM 10 00 In European frequency spacing mode the clock will display 24 hour time 22 00 XD622W OPERATION General Operation Programmable Display Priority Programmable Clock Priority Reset Audio Bass Treble Balance Fader Source Audio Memory Press and hold DISP then press TUNE A to select radio frequency tuner mode or CD track elapsed time CD player mode display priority default Clock is accessed by pressing DISP momentarily Press and hold DISP then press TUNE 3 to select clock display priority Radio frequency or CD track elapsed time is accessed by pressing DISP momentarily Programs unit to display clock no clock when unit is off Press and hold MODE then press PRESET 1 to turn clock priority on off Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs The RESET button is located behind the faceplate Press rotary encoder to select between Volume default Bass Treble Balance amp Fader VOL gt BASS gt TRE gt BAL gt FAD 7 Press rotary encoder until BASS appears Rotate encoder left right to adjust 6 maximum 6 minimum Press rotary encoder until TRE appea
10. of mounting frame into faceplate Faceplate Removal Power On Off Mode Bass Boost Volume Programmable Turn On Volume Confirmation Beep Mute Preset EQ Curves Display Set the Clock 12 24 hour Clock XD622W OPERATION General Operation Press RELEASE and pull away from the left side to remove To re install insert right side of faceplate first then push left side to secure Press PWR or any other button except eject to turn the unit on Inserting a CD will turn the unit on automatically Press PWR to turn the unit off Press MODE to select between AM FM tuner weatherband tuner CD player and auxiliary input Modes of operation are indicated in the display Press BASS to activate and deactivate bass boost curve Activating this feature will enhance the bass frequencies when listening to music at all volumes Adjust volume using rotary encoder 00 46 Press and hold PWR for 3 seconds to program currently selected volume level Press rotary encoder for 3 seconds to turn confirmation beep on off Press MUTE to silence the audio Press MUTE again to cancel Press EQ to select between POP JAZZ CLASSIC BEAT ROCK and OFF default equalization curves Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve Press DISP to select between clock and radio frequency tuner mode or CD track elapsed time CD player mode With the unit on press and hold DISP u
11. out notice Namsung America Inc 21318 64th Ave South Kent WA 98032 Toll Free 1 866 626 7863 2003 Namsung America Inc EVOK0603 V01
12. rs Rotate encoder left right to adjust 6 maximum 6 minimum Press rotary encoder until BAL appears Rotate encoder left right to adjust L12 0 R12 00 represents equal balance Press rotary encoder until FAD appears Rotate encoder left right to adjust F12 0 R12 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM FM Weatherband CD and AUX modes Seek Tuning Manual Tuning Scan Tuning Band Frequency Spacing Storing and Recalling Station Presets Automatically Store Stations Preset Scan XD622W OPERATION AM FM Tuner Operation Press TUNE 3 2 momentarily to seek the next strong station Press TUNE 3 amp for more than 2 seconds then release MANU will momentarily appear in the display Press TUNE 2 25 momentarily to move radio frequency up or down one step at a time Press and hold to advance quickly If tuning is not adjusted for 5 seconds the unit will return to seek tuning mode default AUTO will momentarily appear in the display Press SCAN to preview strong stations on the current band pausing for 5 seconds at each Press SCAN again to cancel Press BAND to select between FM1 FM2 FM3 and AM2 bands Press and hold BAND then press 57 to select European frequency spacing Press and hold BAND then press TUNE A to select U S frequency spacing default Anytime frequency spacing is changed all station presets
13. tall speaker into opening using supplied hardware and test for correct operation TYPICAL MOUNTING METHOD DMP65 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights You may also have other rights which vary from state to state Namsung America Inc warrants this product to the original purchaser to be free from defects in material and workmanship under normal conditions for a period of one year from the date of the original pur chase Namsung America agrees at our option during the warranty period to repair any defect in material or workmanship or to furnish an equal new or renewed product in exchange without charges subject to veri fication of the defect or malfunction and proof of the date of purchase During the One Year Warranty Period For One Year from the date of purchase your product will be replaced with a new renewed or comparable product whichever is deemed necessary if it becomes defec tive or inoperative This is done without charge to you Replacement products are warranted for the balance of the original warranty period Who is covered This warranty is extended to the original retail purchaser for products purchased and used in the U S A in the 48 contiguous states ONLY What is covered This warranty covers all defects in material and workmanship in this product The fol lowing are not covered installation removal costs damage resulting from accident misuse
14. the warranty period to repair any defect in material or workmanship or to furnish an equal new or renewed product in exchange without charges subject to verification of the defect or malfunction and proof of the date of purchase During the One Year Warranty Period For One Year from the date of purchase your product will be replaced with a new renewed or comparable product whichever is deemed necessary if it becomes defective or inoperative This is done without charge to you Replacement products are warranted for the balance of the original warranty period Who is covered This warranty is extended to the original retail purchaser for products purchased and used in the U S A in the 48 contiguous states ONLY What is covered This warranty covers all defects in material and workmanship in this product The following are not covered installation removal costs damage resulting from accident misuse abuse neglect product modification improper installation incorrect line voltage unauthorized repair or failure to follow instructions supplied with the product or damage occurring during return shipment of the product What to do 1 Before you call for service check your operating instructions A slight adjustment of any custom controls may save you a service call 2 If you require service during the warranty period you must carefully pack the product preferably in the original package and ship it by prepaid transport
Download Pdf Manuals
Related Search