Drive Medical Design Light Therapy Device 14000 User's Manual
Contents
1. ail ae WWW DRIVEMEDICAL COM 99 Seaview Boulevard Port Washington NY 11050 Phone 516 998 4600 Fax 516 998 4601 Toll Free 877 224 0946 www drivemedical com True Low Air Loss Therapy Blower Replacement Mattress System Future Air True Low Air Loss Instruction Manual Please Read Manual Before Operating Device Model No 14000PLEASE READ ALL INSTRUCTIONS BEFORE USE CONTENTS IMPORTANT SAFEGUARDS nunuonnnnnannnnnnnnnnnannnnnnnnnnunanannnnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 2 1 INTRODUCTION Ore reer rere reer errr rrr rrr rrrr rrr rrr rrr rrr rr rrrrrrrr rrr rr rrr rrr rrerrrrrrrrrrr rrr rr rrr rer rr rr errr rr rrrrrr rrr rrr rrr rrr rrr 3 1 1 GENERAL INFORMATION OCP PPC CCC errr errr rrr rrr rr rrr rrr rrr rr rrr rrr rer rrr rrr rr tit refer tree reer errr rrr rT 3 1 2 INTENDED USE OCU CCCCCCCCCOCCCCCOCCO CCC CeCe eee eee rere errr rrr rr errr rrr rr rer rrr err rere eee rere ere eer eee ee ee rrr rr er 3 Se PRODUCE DESCARTO goa tae F 21 BLOWER amp MATTRESS SYSTEM nnunsnnnnnnnnnnnnannnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 4 22 BLOWER UNIT snunnnnnnnnnnnannnnnnnnnnnnannnnnnnnnnnnnnnnannnanannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 5 23 FRONT PANEL nnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 5 3 INSTALLATION snnnonnnnnnnnnnnnnnnnnnnnnnnnNNNNNNNNNNNNNENNNNNNNNNNNNNNNNNANNENNENNENNNNNENNAN2. please contact aqualified electrician or serviceman To reduce the risk of electric shock do not modify the cord or plug in any way Check with a qualified electrician or serviceman if the grounding instructions are not completely understood or if in doubt as to whether the product is properly grounded 1 YEAR LIMITED WARRANTY Your Drive brand product is warranted to be free of defects in materials and workmanship for one year of the original consumer purchaser This device was built to exacting standards and carefully inspected prior to shipment This 1 year Limited Warranty is an expression of our confidence in the materials and workmanship of our products and our assurance to the consumer of years of dependable service This warranty does not cover device failure due to owner misuse or negligence or normal wear and tear The warranty does not extend to non durable components which are subject to normal wear and need periodic replacement If you have a question about your Drive device or this warranty please contact an authorized Drive dealer 14 9 TECHNICAL DESCRIPTION Specifications Item Specification Power Supply Note See AC 100 120V 50 60 Hz 5 0A for 120V system rating label on the product AC 220 240V 50 60 Hz 3A for 230V system T5A 250V for 120V system T3A 250V for 230V system Dimension LxWxH 15 8 x 38 x 26 8 cm or 6 2 x 15 x 10 5 Weight 5 5 kg or 12 1 Ib Operation 10 C to 33 C 50 F to
3. store where you purchased this product 2 1 INTRODUCTION BF symbol indicate this product is according to the degree of protecting against This product should be handed over to an applicable collection point for the recycling of electrical and electronic equipment For more detailed information about the recycling of this product please contact your local city office household waste disposal service or This manual should be used for initial set up of the system and for reference purposes 1 1 GENERAL INFORMATION The system is a true low air loss mattress system suitable for prevention and treatment of Pressure Ulcers up through Stage IV The system has been tested and successfully approved with the following standards EN 60601 1 EN 60601 1 2 C EN 55011 Class B IEC61000 3 2 IEC 61000 3 3 A FOR US AND CANADA ONLY KSSE Medical Equipment Air Blower E228589with r sg amp etecirical shock fire and a ie MY in accordance with UL60601 1 AND CAN CSA C22 2 NO 601 1 Le produit t test avec des quipementsm dicauxetrespecte les normes UL 60601 1 amp CAN CSA C22 2 No 601 1 pr venant les choc lectrique le feu et les risques de blessures physiques 1 2 INTENDED USE This product is intended to help treat and reduce the incidence of pressure ulcers from Stage Stage IV while optimizing patient comfort It is appropriate for use in home care long term care and acute care settings A NOTE Equipment not
4. 2 levels higherand wait for a few minutes for best comfort Patient is bottoming out Check if the fowler boost adaptor is connected and secured to the blower unit Check if the fowler boost sensor pad tightly snapped to the designated location inside the bottom of the mattress foam pocket Automatic fowler boost is not functioning If the above information does not solve your problems please contact your local agent directly They might require a technician totake care the problem 2 1 BLOWER AND MATTRESS SYSTEM l By wiping the mattress unit with a damp cloth pre soaked with warm water not to exceed 65 containing a mild detergent and keep it away from dust The cover may also be cleaned using sodium hypochlorite diluted in water All parts should be air dried thoroughly before use NCAUTION Do not use phenolic based product for cleaning CAUTION After cleaning dry the mattress without direct exposure of sunlight The carrying bag if available should be turned inside out and completely wiped down using the disinfectant solutions Allow it to air dry thoroughly Once the inside is dry turn it back and wipe down the outside of the bag with disinfectant solutions 6 STORAGE 1 To quickly vacuum air out from mattress for storage rotate the Quick Connector to the CPR position and press the Max Firm button It will vacuum air out within 5 minutes and then blower will stop automatically Disconnect the automatic
5. 91 F Temperature Storage 15 C to 50 C 5 F to 122 F Shipping 15 C to 70 C 5 F to 158 F Operation 10 to 90 non condensing Humidity Storage 10 to 90 non condensing Shipping 10 to 90 non condensing Class Type BF IPX0O Applied Part Air Mattress Not suitable for use in the presence of a flammable anesthetic mixture No AP or APG protection Mattress Specification 8 Mattress with 10 side bolster Model 2 foam pocket is provided Standard 35 4 width 48 width Dimension 200 x 90 x 20 3 25 4 200 x 122 x 20 3 25 4 cm or LxWxH cmor78 7 x 35 4 x 8 10 78 7 x 48 x 8 10 Weight 7 5 kg or 16 5 Ib 9 5 kg or 20 9 Ib Maximum Weight Capacit 200kg or 440 Ibs 450kg or 1 000lbs A NOTE Mattress dimension and weight is measured without foam cushion Fuse Rating Environment Classification READ ALL INSTRUCTIONS BEFORE OPERATING THIS DEVICE DANGER To reduce the risk of electrocution 1 Always unplug this product immediately after using 2 Do not use while bathing 3 Do not place or store product where it can fall or be pulled into a tub or sink 4 Do not place in or drop into water or other liquid 5 Do not reach for a product that has fallen into water Unplug immediately WARNING To reduce the risk of burns electrocution fire or injury to persons 1 This product should never be left unattended when plugged in 2 Close supervision is necessary when this prod
6. ENNNSNNENENANAENNNNNENNNNNANNNNNNNNNENEEENENN 7 3 1 BLOWER amp MATTRESS INSTALLATION nnnnnnnnnnnnnnnnnnnnannnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 7 4 OPERATION snnnnnnnnnnnnnnnnnnnnnnnnnNNNNNNNNNNNNNNNNNNNNENNNSNNNENNNNENNENNNENNNSSNNNENNNNSENNNENNASENAEENASENNEENNEENNSSNNANNNNNENNNNNNENNEN 9 4 1GENERALOPERATION OPPO CeCe CeCe ere reer errr rr errr errr rer ere r rere tr re rere ee eee en re re 9 4 2 CPR snsnnnnnnnnnnnnnnnnnnnnnNNNNNNNNNNNNNNNNNNNASNNNNNNNNNNNSNNNENNNNNNNSNNENNNNNSNNENNSENASNNNNNSENSEENNNENNENNNNNENNSEENENNNSENNNNENNNNENNNENNN 9 4 3 PRESSURE SET UP snnnonnnnnnnnnnnnnnnnNnnNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNSENNNNENNNNNNNNNNNNNNANNNANNNNEENNEENNEENEN 10 44 AUDIBLE AND VISIBLE ALARM eee eCCEOCeCT COOP Terre er errr rrr rrr rrr rrr rrr retiree etre rt rr re err rrr rT 10 ar seria pile T be ras ie ee E ere e ee eer ete i0 5 CLEANING snnnnnnnnnnnnnnnnnnnnnnnNNNNNNNNNNNNNNNNNNNNSNNNNNNNNNNNNNNNENNNNNENSEENENNNNNENNEENENNAEENANENSNNANENNNNNENNSSNNNNENNNANENENNNNN 10 6 STORAGE snnnnnnnnnnnnnnnnnnnnnNNNNANNNANNNANNNNNNNANNNNNENNNENNNENNNEENNENENNEENNENSNENSNSENNNNNNASESNNAEENAENNENSNASENNNNNNENNNNNNNENENENEN 11 7 MAINTENANCE nnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 11 7 1GENERAL snnnnnnnnnnnnnnnnnnnnnnnnnnnNNNNNNNNNNNNNANNNNNNNENNNNNNNNNNNNNNNENNNNNNNASNEENNENEEENENNSNSNNNNNNNNNNNSNNNNENENENNNENENENENEN 11 7 2 FUSE REPLACEMENT nnunonnnnnnnonannnnnnnannnnnnnannnnnnnn
7. IT type Front 1 Quick Connector 2 Front Panel 3 Handle 4 Auto Fowler Boost Adaptor Rear Power Switch Power Socket Fuses Mounting Bracket Blower Bumper Air Filter oar WN 2 3 FRONT PANEL 3 1 a N f T A O Fowler Boost 5o S A nt drive L i T6 wo 4 1 ComfortLevel Comfortlevel controls the air pressure output When turning up A the output pressure will increase and higherpressure output will Support the heavier weight user Vice vers for decreasing air pressure ooo000000 NOTE Maximum Weight Capacity 200kg or 440 Ibs for 35 4 model 450kg or 1 000lbs for 48 model 4 3 PRESSURE SET UP Users can adjust pressure of air mattress to a desired softness by adjusting the Comfort Level Please consult your physician by the below weight support range for a suitable setting NOTE Maximum Weight Capacity 200kg or 440 lbs for 35 4 model 450kg or 1 000lbs for 48 model 4 4 AUDIBLE AND VISIBLE ALARM When the following situation occurred the LED lights will light up along with the buzzer 4 4 1 CPR When CPR or quick storage is performed or the Quick Connector is on Disconnect position under power on situation the CPR indicator orange LED will light up along with buzzer 4 4 2 Power Failure When electrical shortage occurred or power cord is disconnected without turning off the blower first the power fai
8. fowler boost adaptor on the side of the blower unit Rotate Quick Connector to the Disconnect position and pull up the Quick Connector Lay the mattress out flat and upsides down Roll from the head end towards the foot end Foot end strap can then be stretched around the rolled mattress to prevent unrolling 7 The power cord could be wrapped around the blower bumper on the back of blower Oooh OD A CAUTION When the blower is vacuuming air air temperature is hot Do not block the air outlet A NOTE Do not fold crease or stack the mattresses 7 MAINTENANCE 7 1 GENERAL 1 Check main power cord and plug and auto fowler boost cord if there are abrasions or excessive wears 2 Check mattress cover for signs of wear or damage Ensure mattress cover and tubes are stubbed together correctly 3 Check the air hoses for any kink or break For replacement please contact your local dealers 7 2 FUSER DEARERGENT 2 BlowerUnit 3 Differential Zone Mattress 4 Atiteee 5 Mattress OaM Pocket _ 2 Remove the cover of the fuse holder by means ofa small f o screwdriver 1 Disconnect the plug form mains power when a blown fuse is suspected Fowler Boost Sensor Pad for standard 35 4 mattress only Attest oe _ 3 Insert a new fuse of the correct rating in and replace the d cover of the fuse holder back The fuse should be rated as 5A 250V f 120V system and T3A 250V for 230V system 2 2 BLOWER UN
9. lure indicator orange LED will light up along with buzzer Check to ensure power cord is connected properly 4 4 3 Low pressure When an abnormal low pressure occurred in body section the Low Pressure indicator orange LED will light up along with buzzer Check all tubingsare correctly installed as per installation instructions and ensure all tubingsare secured properly The Low Pressure indicator will continuously light up until the low pressure fault condition is resolved 4 5 ALARM MUTE When these situations mentioned above occurred both the LED light and buzzer will sound off to warn the patient By pressing the button it will temporary mute the buzzer CPR amp Low Pressure so the caregiver may check for possible causes Should the CPR amp low pressuresituation not resolved within 3 minutes the alarm will resume to beep When in Power Failure situation pressing alarm mute button it will cease the buzzer and turn off the power failure indicator 5 CLEANING By wiping the blower unit with a damp cloth pre soaked with a mild detergent and keep it away from dust If other detergent is used choose one that will have no chemical effects on the surface of the plastic case of the blower unit caution The Fowler Boost Sensor Pad should be always kept away from water caution Do not immerse or soak blower unit 10 Grounding Before any connection to the output connectors is made the unit shall be con
10. nected to a protective earth conductor via the three core main cable the mains plug shall be inserted only into a socket outlet provided with a protective earth contact The protective action shall not be negated by the user of an extension cord without protective conductor Several installation tips are listed below After installation the extra length of the power cord if any should be neatly arranged to avoid any tripping accidents The EQUIPMENT should be firmly placed at position where users doctors can access easily 4 OPERATION A NOTE Always read the operating instruction before use 4 1 GENERAL OPERATION 1 Switch on the main power switch found from the side of the blower and press Oon the control panel to turn sii the power 2 The system will automatically go into Max Firm mode for a few minutesof inflation A NOTE The mattress is equipped with differential zone feature therefore center section of the mattress will be inflated quicker than the head and foot sections 3 The low pressure indicator orange LED will light up when the mattress is not fully inflated 4 According to the weight and height of the patient adjust the pressure setting to the most suitable level without ACS E bottoming out 4 2 CPR Connector to the CPR position to release air When CPR needs to be performed quickly rotate the Quick 2 Panel Lock Should the panel remain untouched for5minutes the panel lock fea
11. nnnnnnnnnnannnannnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 11 7 3 AIR FILTER REPLACEMENT OCC CCCCCCCCC CeCe Tere errr errr errr rrr retire rere re eee eer re rr rr err 12 74 RECHARGEABLE BATTERY nunuonnnnnnnnnnnannnnnnnnnnnnnnnnnnnnannnnnnnnnnnnsnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnunnnn 12 8 TROUBLESHOOTING sunsnnnnnnnnnnansnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 12 9 TECHNICAL DESCRIPTION nunnnnnnnnnnnnannnnnnnannnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 13 SAVE THESE INSTRUCTIONS OCC P OC CCCCO COCO C COCO CC OCC e Cre rr rr errr re rrr terre rere rrr reer ere rere re rer re er errr ee 14 1 IMPORTANT SAFEGUARDS SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This product should be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This product is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded DANGER I mproper use of the grounding plug can result in a risk of electric shock If repair or replacement of the cord or plug is necessary do not connect the grounding wire to either flat blade terminal The wire with insulation having an outer surface that is green with or without yellowstripes is the grounding wire NOTE If the repair or replacement of the cord is necessary
12. osition When a click sound is felt or heard the connection is completed and secured A NOTE The blower is only operable at Lock On position 4 Connect and secure the automatic fowler boost adaptor on the side of the blower unit The automatic fowler boost sensor pad must snap to the designated location inside the bottom of the mattress foam pocket F This function is only available for 35 4 replacement mattress system A NOTE Use the Velcro strips to fasten the cable of fowler boost sensor pad to prevent stumbling 5 Plug the power cord into electrical outlet A NOTE 1 Make sure the blower unit is suitable for the local power voltage 2 The plug is also served to disconnect the device A CAUTION The blower can only be applied to the mattress recommended by the manufacturer Do not use it for any other purpose applied part air mattress 6 Then turn the main power switch to ON position
13. patient A CPR During the CPR situation the caregiver can rotate the quick connector to perform CPR Once the quick connector is switched to CPR mode CPR alarm will sound with LED light on to notify the caregiver B PFA Power Failure Alarm During power failure situation the Power Failure LED light will light on with buzzer By pressing the mute button to disable both buzzer and LED C Low Pressure Indicator When low pressure LED continuously lights up with buzzer the pressure inside of air mattress body section is abnormal please check all tubings arecorrectly installed as per installation instructions and ensure all tubings are secured properly N TE The low pressure indicator will not be detected if air cells of mattress are purposely disconnected 3 INSTALLATION Unpacking the box to inspect for any damage which may have occurred during shipment If there are any damages please contact your dealer immediately 3 1 BLOWER amp MATTRESS INSTALLATION 1 Place the mattress on top of the bed frame Please note for the foot end 2 Hang the blower onto bed rail foot end and adjust hangers to best upright position of the blower A NOTE Do not place the blower on flat surface this might block the air intake of blower unit 3 Connect air hose connectors from air mattress to the blower unit Make sure the connector is in the right position as the inserted diagram below Rotate the connector clockwise to the Lock on p
14. suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide A NOTE L quipement ne peut treutilises il y a risque de m lange d un anesthesique inflammable avec I airoul oxygeneouoxydenitreux 2 PRODUCT DESCRIPTION 7 3 AIR FILTER REPLACEMENT 1 Replace the air filter locatedat the bottom of blower 2 The filter is reusable and can be washed gentlywith a mild detergent and water Dry the filter before use 3 Check and replace air filterregularly if environment is dirty 7 4 RECHARGEABLE BATTERY 1 To check if the rechargeable battery has been drained out unplug the power cord andsee if the Power Failure indicator will light up along with buzzer last for a few minutes 2 If the Power Failure Alarm is unable to work or the battery might need to be replaced approximate life expectancy 6 months user can contact your dealer or notify the technician for replacement 8 TROUBLESHOOTING Problem Solution e Check if the plug is connected to mains e Check if there is any blown fuse Power is not ON Check if the Quick Connector is rotated to the Lock on position Check if the power is suddenly shut down Check if the connection between air tube connector to blower unit is tightly secured Check if all tubing connections along mattress are secured Alarm is on Audible amp visual Pressure setting might be inadequate for thepatient adjust comfort range 1 to
15. ture will lock the panel with green LED light on to prevent accident from changing the setting during normal operation To unlock simply by pressing the Panel Lock button for 3 seconds 3 Max Firm This mode will be forced to execute every time the power is turned on This insures the blower is able to reach its maximum operating pressure Once the max pressure level is reached the blower will automatically switch into the previous selected comfort level User can also use this function as full mattress inflation during patient ingress egress for better support There is a 20 minutes auto recovery mode to return back the previous selected comfort level 4 On off Press On to turn on the unit Press Off to turn off standby the unit VTE The power switch on the side of blower must be turned on 5 Fowler Boost The automatic Fowler Boost featuresadditional supports to the patient during upright position to prevent bottoming out This function is automatically activated when the bed is raised and deactivated when the bed is flat A NOTE This function is only available for 35 4 replacement mattress system A NOTE When the patient in the raised position it is recommended that caregiver readjust the patient sitting posture to prevent possible bottoming out 6 Alarm Mute Press alarm mute button to temporary suspend the CPR and low pressure alarm Should the situation not resolved within 3minutes the alarm shall resume tonotify the
16. uct is used by on or near children or invalids 3 Use this product only for its intended use as described in this manual Do not useattachments not recommended by the manufacturer 4 Never operate this product if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the product to a service center for examination and repair 5 Keep the cord away from heated surfaces 6 Never block the air openings of this product or place it on a soft surface such as a bed or couch where their openings may be blocked Keep the air opening free of lint hair and other similar particles 7 Never drop or insert any object into any opening or hose 8 Connect this product to a properly grounded outlet only See Grounding Instructions NOTE CAUTION AND WARNING STATEMENTS NOTE Indicate some tips CAUTION Indicate correct operating or maintenance procedures in order to prevent damage to or destruction of the equipment or other property WARNING Calls attention to a potential danger that requires correct procedures or practices in order to prevent personal injury Pp lt u O m 0 REP Authorised representative in the European community Manufacturer electric shock for type BF equipment Grounding terminal for 230V system Attention should read the instructions Disposal of Electrical amp Electronic Equipment WEEE bt gt OPRIE the retail
Download Pdf Manuals
Related Search