Dixon Marking Tools ZTL 312 User's Manual
Contents
1. Bin 3506 TURE rop TIRE SIGG WHEEL sa li 3204 be Gu 15407 L thy 3786 UN 3007 T 2266 i 014 p 2195 1292 Ze 1285 Fant 1556 2401 ASSEMALT A578 WHEEL m YA KI 12 Transaxle Assembly D TRANGAYLE TOOL KIT 861 a HARDWARE PACE AGE Fot TOOL KIT a a E ane PUNCH cs PUNCH 8758 asy ARAR ir BEAR H DR VER DRIVER d TAANS GECH 4256 Beh DIS LUP A GRKMENT 113584 zanne d 1 13328 Sons R we A Ne 3334 257 g one Pa H Nr pe a Bitz Ss IG RE soti 255524 a a aza NE 2509 a w i LF 4 i 5249 i 5170 3052 s207 5242 5264 T 1206 LTE 3 Z 8 1 a ki U I Ole 312 Wiring Assembly LA essi FO me siika EEN Kat T 4752 e L 4586 COVER ONLY ANM ae WW V 7 SWITCH MAGNETO KILL A TO Br 4598 IGNITION AL TERNATOR CIRCUIT SWITCH i o A NE ees sl Sm YO STARTER S lt 4216 ea 42 ANE a z es 4556 A MELY A dis 4413 COVER ONLY BODY WIRING LOOM 4762 g i WIRING KIT 8369 4465 ASSEMBLY SEE ASSEMBLY BREAKDOWN 4466 COVER ONLY BATTERY sore oe rao ES Sigs Ji cede Gen ed I lt gt 0019 P e 312 Body Assembly SE EE ep aSpa COVERED Ox Bet EK e s F wo SRE 14652 w DECALS n 137052. deck Roll chassis free of the deck 1 To Install reverse the above procedure MOWER BLADE OPERATION To engage mower blades turn engagement lever on floor slowly to the ON position To disengage mower blades turn lever slowly to the OFF position IMPORTANT PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS 1 After reassembly while seated on mower attempt to start engine with mower deck engaged Engine should not start If engine does start return the mower to an Authorized Dixon Dealer for adjustment or repair 2 Disengage mower deck and start engine With the operator in the normal seated position engage mower deck and remove weight from seat The engine should stop If the engine doesn t stop when operator rises from the seat return the mower to an Authorized Dixon Dealer for adjustment or repalr 3 Engage then disengage mower blade in each cutting height Insure that blade disengages and comes to a stop within 5 seconds In each height position If blade does not disengage properly contact your Authorized Dixon Dealer PARKING BRAKE ADJUSTMENT Remove the body as described above Tighten nut on brake rod P N 2533 located in front of the transaxle on each side just enough to prevent brake from slipping when engaged CAUTION Over tightening may cause premature wear on the brake band P N 5085 Page 2 of 7 Revised 1 92 P N 8114 8374 we GRIP 7536 ASSEMBLY 6373 w GRIP
3. DIXON INDUSTRIES INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2000 FAX 316 251 4117 TECHNICAL DATA ZTR MODEL 312 IMPORTANT READ OPERATOR S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS SEAT ADJUSTMENT A 1 Pull or lift body retention latch P N 3934 lt e from transaxle backing plate raise and push a body and seat assembly forward 2 Loosen four seat ad jus tee it knobs P N 1849 and sl de seat forward or backward to desired ALA position 2 a 3 Re tighten seat adjustment knobs P N 1849 DO Se NE LESS yek NOT operate Bower without seat adjustment knobs Sa Ce _ properly tightened CR SIA Rit 4 Close upper body and push retention canini N di latch P N 3934 over transaxle backing plate TREE BACX In Mare a Sy Eise GE REMOVING THE BODY 1 The 312 has a 2 piece polyethelene body The upper body can be folded forward to expose the transaxle In some cases 1t nay be necessary to remove the upper body to service the transaxle 2 To relieve upper body remove two bolts P N 3080 from the front of upper body hinge located on the brake shaft P N 9283 Disconnect seat switch P N 4761 at plug in 3 Reverse above procedure to reinstall ADJUSTMENT OF MOWER DECK DRIVE BELT 1 This mower deck drive belt is tensioned by a spring loaded engagement idler quadrant 2 This system is designed to maintain the proper belt tension at all
4. times 3 Belt tension can be adjusted by moving the engaging rod P N 7013 into the outside hole of engagement handle P N 7020 4 After belt tension is adjusted check to assure that the mower blade will not turn freely when the engaging rod is in the OFF positon 5 If the mower blade turns freely adjust the blade brake by loosening nut P N 3205 at the end of the brake rod P N 2988 6 After adjustment is achieved perform the safety checks listed below Page 1 of 7 REMOVING THE MOWER BLADE Secure blade P N 2483 from turning Remove blade bolt from center of blade P N 3268 and blade washer P N 6260 then remove blade P N 2483 To reinstall reverse above procedure WARNING Sharp edges on blade can cause Injury Caution should be exercised when service is required on blade REMOVING THE MOWER DECK 1 Loosen belt keeper P N 7026 7027 located under the engine by loosening two rear engine mounting bolts allowing the deck drive belt to come free of the rear pulley 2 Disconnect the wiring loom at the deck safety switch P N 4242 3 Remove the two clevis pins P N 3072 from the two rear L rods P N 1355 and slide from slots 4 Remove clevis pin P N 3072 from L rod attached to lift handle and slide from slot 5 Remove clevis pin P N 3072 from front deck hanger shaft P N 1332 located at front of mower deck on slide plates welded at battery box and remove 6 Lift front of mower chassis clear of
Download Pdf Manuals
Related Search