Directed Electronics 563T User's Manual
Contents
1. 2003 directed electronics inc 15 panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter Just press for two seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time a press on the remote transmitter again valet mode 16 You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the remote transmitter but all convenience functions door locks trunk release etc will continue to work normally To enter or exit Valet Mode Turn the ignition on l 2 Turn the ignition off TS a 3 Press and release the Valet 29 No switch within 10 seconds The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode To enter or exit Valet Mode using the transmitter 1 Open any vehicle door 2 Press 2003 directed electronics inc 3 Press 4 Press Al e a again The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode remote start This feature allows you to remotely start and run your vehicle for2. a programmable period of time This makes it possible to warm up the engine as well as adjust the interior temperature of the ve hicle with the climate control system If interior heating or cooling is desired the climate controls must be preset and the fan blower must be set to the desired level prior to remote starting the vehicle important 1 Never remote start your vehicle when the keys are in the ignition except when performing Valet Take Over and 2 Never start the vehicle if it is not in either PARK or NEUTRAL To remote start the vehicle 1 Press O on the transmitter twice within 3 seconds 2 The parking lights will flash to confirm that the vehicle will attempt to start 3 In gasoline vehicles the engine will start 4 seconds after the parking lights flash In diesel vehicles the engine will start when the WAIT TO START indicator on the vehicle s dash goes out O 2003 directed electronics inc 17 18 4 Once the vehicle has started it will run for the pre program med period of time either 12 24 or 60 minutes see Programming Options section of this guide or until a shut down input is triggered important It is unsafe to operate a vehicles motor in a garage or other closed off area Breathing the exhaust from the vehicle is hazardous to your health Never acti vate the remote start in an enclosed space When you are ready to drive the vehicle
3. absence Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal moni toring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second Bypass Notification chirp Once the light turns off however the security system resumes normal monitoring note Bypass Notification does not occur when the sys tem is in Silent Mode or if the notification chirps have been programmed off by the installer O 2003 directed electronics inc 25 disarming diagnostics Extra chirps that are heard when disarming the system are the Tamper Alert If four chirps are heard when disarming the system then the security system was triggered in your absence If five chirps are heard when disarming the system a zone was trig gered so many times that the Nuisance Protection Circuitry has bypassed that zone In either case the status LED will indicate wh
4. without a transmitter you must have the vehicle s ignition key and know where the Valet switch is located Be sure to check with your installer at the time of installation for both the location and the preset response 1 5 presses of the Valet switch 2003 directed electronics inc To disarm the security system turn the ignition to the ON posi tion Press the Valet button the preset number of times one to five times within 15 seconds After five seconds the system will disarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of Valet Button Number of Presses important The Valet switch can be programmed to respond to 1 5 presses for the disarm function You must check with the installer to verify the programming for your individual unit silent mode To temporarily turn off the arm or disarm chirps use Silent Mode M Simply press for less than one second before arming or disarming and the confirmation chirp s will be elim inated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The Warn Away response to lighter impacts is bypassed if the system is armed using Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering Only the Warn Away response is bypassed
5. 876 0800 Directed security systems including this unit are deterrents against possible theft Directed is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability what soever including without limitation liability for theft damage and or vandalism Directed does not and has not authorized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile VWMYWVWYvvVvvvyv Installation receipts ii 2003 directed electronics inc table of contents o o limited lifetime consumer warranty 22 i standard transmitter configuration 3 whats included oosina ya Sn dat 4 important information 4 System Maintenance vedado Lim bane oe cares Boas dre das des ees 5 VOUL Watan ee Sen Leta atta oe Det ata Ue ah Notte o ORs A 5 fechid MOC iss oye defere
6. An XHF receiver antenna Two four button transmitters A Stinger DoubleGuard two stage shock sensor A Revenger Soft Chirp six tone programmable siren A red status LED indicator light A push button Valet switch Your warranty registration VVVV VV VV VY A shut down toggle switch Congratulations on the purchase of your combination remote start alarm system Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer certifi cate to verify authorization By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing our web site at www directed com 4 2003 directed electronics inc system maintenance The system requires no specific maintenance Your remote is powered by a small lightweight 3 volt lithium battery that will last approximately one year under normal use When the battery begins to weaken operating range will be reduced and the LED on the remote will dim gt your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you re
7. K If shut down with the remote start button the system will remain in timer mode 5 The system will start every 3 hours until canceled by the brake hood or neutral safety shut down wires important Timer Mode should be used only in open areas Never start and run the vehicle in an enclosed space such as a garage or carport To exit timer mode turn the ignition switch on any time the engine is running The parking lights will flash 4 times indi cating timer mode has been exited 2003 directed electronics inc 21 safety features o This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components starter anti grind circuitry Whenever the vehicle is remote started advanced anti grind circuitry prevents the starter from engaging even if the key is turned to the start position This prevents damage to the starter motor if the key is turned to the start position during remote start operation disabling the remote start system This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the shutdown toggle switch to the OFF position The switch can be installed in a location of your choice Check with your installer fo
8. period of time in which no operation has been performed This lowers the current draw on the vehicle s battery Power Saver Mode takes over under the following conditions gt Power Saver when the system is armed After the system has been armed for 24 hours the LED will flash at half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a one hour period while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off O 2003 directed electronics inc Programming options control your system s normal operational set up Most options do not require additional parts but some may require installation labor The following is a list of the programmable options with the factory settings in Bold gt Active arming transmitter only or passive arming auto matic arming 30 seconds after the last door has been closed Arming disarming siren chirps on or off The ignition controlled door lock feature on or off When this feature is programmed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off If your installer is programming the security system with the Directed Bitwriter ignition loc
9. release for the vehicle s trunk or hatch 2003 directed electronics inc Although the on board relay can control most power trunk re leases sometimes an optional relay is required If the factory release is not power activated Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is pro vided with the 529T and 530T systems These can operate power windows and can roll them up automatically when the system is armed roll them down or both up and down Mobile Video This system is compatible with Directed Video s MCB1000 Multi Channel Controller featuring on screen secu rity system programming and zone trigger information O 2003 directed electronics inc 35 glossary of terms 36 Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the microprocessor which monitors your vehicle and controls all system functions Fault Proof Starter Interrupt An automatic switch controlled by your system that prevents the vehicles starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet Mode or if the starter interrupt switch itself fails Your system has feature ready circuitry for the starter interrupt however installation may require additional labor Input A physical connection to the system An input ca
10. 1 Insert the ignition key and turn tion 2 Press the brake pedal note If the brake pedal is pressed before the key is in the ON position the engine will shut down While the vehicle is running during remote start operation the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut down inputs gt The brake pedal is pressed gt The hood is opened gt The shutdown toggle switch is put into the OFF position gt The pre programmed run time 12 24 or 60 minutes has elapsed gt Transmitter buttons Ok is pressed twice within 3 seconds 2003 directed electronics inc valet take over The Valet Take Over feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate controls on To pertorm Valet Take Over 1 Before turning off the engine press and release Ok twice within 3 seconds on the transmitter or press and release the optional momentary switch Then wait five seconds 2 Turn the ignition key to the OFF position The engine will stay running 3 The engine will run until the pre programmed time elapses or a shut down input is received See the previous Remote Start section for a complete li
11. ILITY WHATSOEVER INCLUD ING WITHOUT LIMITATION LIABILITY FOR THEFT DAMAGE AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REINSTALLATION OF THE UNIT OR ANY 2003 directed electronics inc i CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV ER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con sequential damages This warranty gives you specific legal rights and you may also have other rights that vary from State to State This product may be covered by a Guaranteed Protection Plan GPP See your autho rized Directed dealer for details of the plan or call Directed Customer Service at 1 800
12. Model 5631 gt Owner s Guide limited lifetime consumer warranty Directed Electronics Inc Directed promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed dealer the unit will be pro fessionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information con sumer s name telephone number and address the authorized dealers name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including without limitation the siren the remote trans mitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non transferable and is automatically void if the original purchaser has not completed the warra
13. any time by pressing EN disarming N To disarm the security system press amp You will hear two chirps and the parking lights will flash twice If the power locks are controlled by the system the doors will also unlock The siren chirping either four or five times when disarming indicates Tamper Alert which is described in the Diagnostics Section of this guide 2003 directed electronics inc 13 high security disarm This security system offers High Security Disarm High Security Disarm is a feature that makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds pressing J on the remote transmitter will stop the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visu ally checking the vehicle Pressing d E after resetting the system will disarm the system pressing this button during the first six seconds of the triggered sequence will disarm the security system immediately The six second timer is provided for your conve nience in case the system is accidentally triggered disarming without a transmitter If your remote transmitter is lost or damaged you can manually disarm your vehicle security system To disarm the system
14. ceive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 2003 directed electronics inc 5 caution This product is designed for fuel injected automatic transmis sion vehicles only Use of this product in a standard transmission vehicle is dangerous and contrary the product s intended use transmitter functions The receiver uses a computer based Learn Routine to learn the transmitter buttons This makes it possible to assign any remote transmitter button to any receiver function The transmitter initially comes programmed with Standard Configuration but may also be customized by an authorized dealer The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter 3 standard configuration A Button The arming and panic functions are controlled by pressing this button for one second d Button The disa
15. d dealer gt When properly installed this system can start the vehicle via a command signal from the remote control transmitter Therefore never operate the system in an enclosed area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partially enclosed area or when having the vehicle serviced the remote start system must be disabled using the installed toggle switch It is the user s sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole respon sibility of the user gt Use of this product in a manner contrary to its intended 8 O 2003 directed electronics inc mode of operation may result in property damage personal injury or death 1 Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the neutral safety feature of the vehicle periodically checked wherein the vehicle must not remotely start while the car is in gear This testing should be performed by an authorized Directed dealer in acco
16. d easy reference to keep in your purse or wallet PA DO QUICK REFERENCE GUIDE Arming M To arm press A When the system arms you will hear a short chirp and the parking lights will flash once Arming while driving M To arm the system while driving press on your transmitter while the vehicle is running The system will chirp once and then once more to indi cate that the ignition is on Disarming M To disarm press ef You will hear two chirps and the parking lights will flash twice High security disarm M For high security disarm press on your transmitter and the siren will stop sounding To completely disarm the security system press again and the system will chirp 4 or 5 times reporting the trigger Disarming without a transmitter M Turn on the ignition Press the Valet switch within 15 seconds The system should now disarm If it does not you may have waited too long so turn the ignition off and on and try again Silent Mode M Pressing briefly before arming or disarming will eliminate the confirma tion chirp s for that one operation only Panic Mode M Press for 2 seconds and you will enter Panic Mode The siren will sound and the lights will flash for 30 seconds To stop Panic Mode at any time press on the transmitter again To remote start the vehicle M Press EF twice within 3 seconds The parking lights will turn on if connected and the vehicle will start and run for the programmed period of ti
17. en armed your vehicle is protected as follows gt Light impacts trigger the Warn Away signal When trig gered the siren chirps and the parking lights flash for a few seconds gt Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for a pre programmed period which can range in duration from 1 to 180 seconds gt If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the system is armed while still providing instant re sponse even if the door is immediately closed gt Turning on the ignition key will trip the same progressive re sponse as opening a door gt The optional starter kill prevents the vehicle s starter from cranking O 2003 directed electronics inc 11 multi level security arming Multi Level Security Arming allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section of this guide Pressing only in Standard Configuration again within five seconds of arming the system will activate the Multi Level Security feature Each time is pressed again a different security level is selected The d
18. full triggered response can be programmed for any duration ranging from 1 to 180 seconds Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter will be disabled To start the O 2003 directed electronics inc car it will be necessary to disarm the system with the trans mitter It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times AED is also disabled when the system is in Valet mode note This feature will only function if the FailSafe Starter Kill relay has been installed gt Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by a dealer resulting in a unique easily identifiable siren sound The chirps can be either full volume or 6 decibels quieter than the full alarm blast gt The engine can be programmed to run for any duration ranging from 1 to 60 minutes 12 minutes is the default After the programmed run time the engine w
19. ich zone was involved see Table of Zones section The security system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time that the ignition is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the systems status as described below Action Number of Chirps Description Arm 1 System armed Arm 1 3 second delay 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC active 26 O 2003 directed electronics inc table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input Standard input assignments are listed in the following table along with spaces to write in any optional sensors or switches that have been installed ZONE Number of LED Flashes 1 2 DEALER INSTALLED DESCRIPTION OPTIONS Trunk Pin Instant trigger a heavier impact detected by the shock sensor Door switch trigger Instant trigger for optional sensors Ignition trigger Hood Pin interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics If you receive a Bypass notification when arming or a Tamper Alert notification when disarming look at the LED Active or triggered zones will be indicated by a
20. ifferent security levels are selected as follows gt gt Press once The siren chirps once The system is armed Press a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed Press a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed Press a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now bypassed Press le fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed O 2003 directed electronics inc note Multi Level Security Arming only applies to a sin gle arming cycle Once the system is disarmed and then re armed all the zones will be active again arming while driving Your security system can be armed while driving the vehicle Simply press on the transmitter for two seconds while the vehicle is running The siren will chirp once to indicate that the security system is armed and then once more to indicate that the ignition is on The system will not respond to any input except the door triggers and the starter kill relay if installed will not be activated Once you have arrived at your destination the system will disarm when the ignition is turned off The siren will chirp twice and the LED will then stop flashing The system can also be disarmed at
21. ignal Enjoy a phenomenal increase in range even in areas with high radio interference a Owner Recognition is a revolutionary new feature available only from Directed Using a Directed Bitwriter hand held program ming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each transmitter that is used with the system Then whenev er a specific transmitter is used the system will recall the settings assigned to that transmitter Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user note Owner Recognition cannot be programmed with out a Bitwriter and the necessary software Check with your dealer for more information 2003 directed electronics inc 29 d odi This Directed system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a
22. ill shut down and will not restart unless in Timer Mode gt While the remote start system is running the engine the parking lights of the vehicle can flash on and off or come on and light steadily 2003 directed electronics inc 33 34 Listed below are some of the many expansion options available Please consult your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery is dis connected Hood Lock Prevents the vehicle s hood from being opened without a key keeping thieves away from the system s siren the battery connections and other components under the hood Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the 508D radar sensor Your system can react to any intrusions into this field with the full triggered sequence Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Power Trunk Release The accessory output of the system can op erate a factory power
23. k and unlock are independent features that can be programmed separately Passive door locking with passive arming or active door locking only when arming with the transmitter Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Panic mode enabled disabled when the ignition is turned on Some states have laws against sirens sounding in moving cars 2003 directed electronics inc 31 32 gt Forced passive arming on or off If your security system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open Forced passive arming ensures that the system will be armed if a door has accidentally been left ajar when leaving the vehicle note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Directed Bitwriter the
24. me To disable the remote start system M To disable the remote start move the shutdown toggle switch to the OFF position Location of Valet switch Number of Valet switch pulses for disarming O 2003 directed electronics inc 39 40 2003 directed electronics inc 2003 directed electronics inc 41 The company behind this system is Directed Electronics Inc Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services 0 E Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers driven to excel Vinected ELECTRONICS INC Vista CA 92081 www directed com 2002 Directed Electronics Inc All rights reserved G563T 6 03
25. n be pay y P provided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights LED A red light mounted at a discretionary location inside the vehicle It is used to indicate the status of your system Shock Sensor This system has a dual zone shock sensor This sensor is mounted in the vehicle and designed to pick up impacts to the vehicle or glass Transmitter A hand held remote control which operates the various functions of your system Trigger or Triggered Sequence This is what happens when the O 2003 directed electronics inc alarm goes off or trips The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration Valet Switch A small push button mounted at a discretionary location inside the vehicle It is used to override the starter inter rupt when a transmitter is lost or damaged or to enter or exit Valet Mode Warning Zone Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 2003 directed electronics inc 37 38 2003 directed electronics inc Cut along dotted line and fold for a quick an
26. ns Bird oe ees Gite tree ee dates were eat 5 CAU MERS A ves Arar eres ove Net as LE trian des DNS MES te ea 6 transmitter FUNCHONS esra 0 20 e iste tierce newt ti 6 standard configuration 6 USING YOUL SYSTEM sssssssssssessesesesesseeeesesssss 8 Watilitig safetysfitstic crus dans wea ars US aay aya hens ih moe 8 ACTIVE AMOO e cities dede aiken a AA aterm tee sd ipl etes Lok 10 PASSIVE AMI Gs ioe are Te cree ann OR A OY eee Meo det AR 10 multi level security arming 12 arming while drivitig wis i hace dee ede he Ball Ge toast 13 SAINT Oceana PE nr Nala iy Ne Ce ai tole ne Sen hin 13 high security disafm 4 4 ss isa de la e EE S 14 disarming without a transmitter 14 Silent Modes 2 5 34 od iid Fas wed ated nee ohne dea E A 15 panic Modems woos A See a ee ie ok 16 vale modestie est nr BR Wo US ee Dene Se Leta 16 TEMO ica Sea ee ee ee ei ane EAR ORGS annie ed ee 17 valer take over ihn Aes Code o el re Ui be Mgt ae A 19 Short run turbOs essee 8e ine pn ee Bane ads 20 timer modes vienne nn EEE Eee Peas He eee ae 20 Safety features lt 62 O alesse nase Wh 22 starter anti grind Circuits e ea ie ccc cece eens 22 disabling the remote start system 22 over and under rev protection 22 Shut doit pts cils Lo ba ne Se bid 23 nuisance preven
27. nty card and mailed it within ten 10 days of the date of purchase to the address listed on the card the unit s date code or serial num ber is defaced missing or altered the unit has been modified or used in a manner con trary to its intended purpose the unit has been damaged by accident unreasonable use neglect improper service installation or other causes not arising out of defects in materi als or construction The warranty does not cover damage to the unit caused by installa tion or removal of the unit Directed in its sole discretion will determine what consti tutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUD ING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL ERS OR INSTALLERS DIRECTED SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM DAM AGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DISCLAIMS ANY LIAB
28. pattern of blinks by the LED O 2003 directed electronics inc 27 Example If zone 3 was active or triggered the LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on note Your system stores the last two triggered zones in memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details code hopping 28 The receiver and transmitters use a mathematical formula called an algorithm to change their code each time the transmitter is used This technology has been developed to increase the secu rity of the unit The control unit knows what the next codes should be This helps to keep the transmitter in sync with the control unit even if you use the remote control out of range of the vehicle However if the remote has been pressed many times out of range of the vehicle or the battery has been removed it may fall out of sync with the control unit and fail to operate the system To re sync the remote simply press C1 several times within range of the vehicle The alarm will automatically re sync and respond to the transmitters normally O 2003 directed electronics inc Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable s
29. r recommended locations Location of Shutdown Switch over and under rev protection The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the 22 O 2003 directed electronics inc programmed levels This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race note The system uses a wire connected to the vehicle to sense engine speed This wire must be connected in order for over and under rev protection to work shut down inputs This security system uses several inputs to shut down the remote start operation of the motor or prevent remote start if certain inputs are active The two most important are hood and brake inputs The hood input will prevent the motor from starting as well as shut it down any time the hood is opened The brake pedal will shut down the motor at any time during remote start operation as well as preventing the remote start from activating while it is being pressed 2003 directed electronics inc 23 nuisance prevention circuitry 24 Your system has Directed s Nuisance Prevention Circuitry NPC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same
30. rdance with the Safety Check outlined in the product installation guide If the vehicle starts in gear cease remote start operation immediately and consult with the authorized Directed dealer to fix the problem gt After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle starts when performing the Neutral Safety Shutdown Circuit test the remote start unit has not been properly installed The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear All installations must be performed by an autho rized Directed dealer OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPER ATION OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMMEDIATELY CEASE THE USE OF THE 2003 directed electronics inc 9 UNIT AND SEEK THE ASSISTANCE OF AN AUTHO RIZED DIRECTED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS active arming You can arm the system by pressing a of your transmitter for one second When the system arms you will hear a short siren sound or chirp and see the pa
31. rking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the status LED will flash approximately once per second indicating that the system is actively protecting your vehicle If you hear a second chirp after arming and note that the status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification passive arming 10 The system can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the status LED will flash twice as fast as it does when the system is armed At the 20 second point of the count 2003 directed electronics inc down the siren will chirp to indicate that the system is about to arm At the 30 second point the parking lights will flash to indicate that the system is armed note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is pro grammed on See Programming Options section Addi tionally each time a sensor is triggered during the arming countdown the 30 second countdown starts over Wh
32. rming function is controlled by pressing this button for one second Button Silent Mode and an optional auxiliary function are controlled by this button Silent Mode works by pressing this button for 6 2003 directed electronics inc less than one second before arming or disarming An optional auxiliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls K Button The remote start function of your system is controlled by pressing this button twice within 3 seconds and Buttons An optional auxiliary convenience or expansion function that P y P you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls and Buttons An optional auxiliary convenience or expansion function that P y P you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls and Buttons The remote start timer mode is controlled by pressing these buttons simultaneously K and AUX Buttons The short run turbo mode is activated when these buttons are pressed simultaneously 2003 directed electronics inc 7 warning safety first The following safety warnings must be observed at all times gt Due to the complexity of this system installation of this product must only be performed by an authorized Directe
33. sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the security system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continually being triggered will remain bypassed The vehicle doors are protected by NPC differently If your security system is triggered by an open door for three full cycles the system will bypass the doors until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working If five chirps are heard when disarming NPC has been engaged If you wish to clear the NPC memory turn the ignition on 2003 directed electronics inc The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your
34. st of shut down inputs note This feature will not work if the brake pedal is being pressed 2003 directed electronics inc 19 short run turbo Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1 3 5 or 10 minutes This allows the systems timer to conveniently cool down the turbo after you have left the vehicle To activate 1 Park the vehicle and set parking brake 2 Remove your foot from the brake pedal and leave the engine running 3 Press and release the EJ and buttons at the same time 4 The lights will flash to indicate the remote start has entered short run turbo mode 5 Turn off the key the engine will keep running 6 Exit and secure the vehicle 7 The engine will turn off after the programmed run time timer mode 20 By pressing the remote A and d buttons the parking lights will flash 4 times and then start the vehicle and run for the set duration The remote start can be shut off by the transmitter by pressing the remote start button and remain in timer mode but if any other shut down zones or the ignition becomes 2003 directed electronics inc active the timer mode will cancel 1 Press Timer mode buttons 2 The vehicle will confirm with 4 parking light flashes 3 A 1 second delay will start 4 The system will start the car and will run for the specified duration unless shut down by the remote start button
35. tion CILCUILLY es ee 24 ANOS iia se donner dune SE and cg eee hate ben fers Li 25 arming diagnostics scr ards wk she eden a dns Wiebe e Pet ee 25 disarming diagnostics 26 systemi Status Chips ci eee le een oeil 26 tabl of zones iii a tt de 27 interpreting zone diagnostics 27 code hopping stunt dinde de ld ete cada Cd 28 high frequency cs rt 29 O 2003 directed electronics inc 1 owner recognition sssssssseesesessssseseeessssssse 29 rapid resume logic 30 power Saver modernes a A AL a A ek els 30 programming options ss ssssssssee 31 security amp convenience expansions es se 34 glossary of terms 36 2 2003 directed electronics inc controls the Arm and Panic On Off function A G controls the Disarm and Panic Off function AUX controls Silent Mode and Auxiliary channel 2 output controls the Remote Start function A 25 and a pressed together control the Timer mode UX and pressed together control Turbo Short Run D and AUX pressed together control channel 4 output D pb yr and AUX pressed together control channel 5 output 2003 directed electronics inc 3 A control module
Download Pdf Manuals
Related Search