Dimplex DFB8842 User's Manual
Contents
1. 2011 Dimplex North America Limited 232. Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of times you need to open the unit to replace light bulbs Care must be taken when removing the Log Set as the Log Set contains LED s and wires Lower Light Bulb Requirements Quantity of three 3 clear chan delier or candelabra bulbs with an E 12 small socket base 60 Watt rating Example GE 60BC or Philips 6OCTC Do not exceed 60 Watts per bulb To access the lower light bulb area 1 Slide fireplace out of mantel Figure 7 Upper Light Bracket Lower Bulbs Log Set Assembly Upper Bulbs Front Glass Trim oe Maintenance 2 Remove four 4 Phillips screws from right side of trim Figure 7 3 Remove trim 4 Slide glass to right side of fireplace to remove Figure 7 5 Pull the front edge of the plastic Log Set or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the mirror Figure 8 IMPORTANT Only handle the Log Set Assembly by the Ember Bed or plastic grate NOTE Log Set Assembly fits tightly into firebox some force may be necessary to remove Figure 8 Log Ember Bed Back rea Ledge m Rear e Tab Side Section Front Edge 6 Set Log Set Assembly in front of fireplace 7 Unscrew bulbs
3. always be followed to reduce the risk of fire electric shock and injury to persons including the following D Read all instructions before using this appliance e The heater is hot when in use To avoid burns do not let bare skin touch hot surfaces The trim around the heater outlet becomes hot during heater operation Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9m from the front of the unit 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended 4 Always unplug the fireplace when not in use 5 Do not operate any unit with a damaged cord or plug or if the heater has malfunctioned or if the fireplace has been dropped or damaged in any manner Return heater to authorized service facility for examination electrical or mechanical adjustment or repair 6 Do not use outdoors 2 The fireplace is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container Do not run the cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 9 To disconnect the unit turn the controls off then remove the plug from the outlet Do not insert or allow foreign
4. objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or CAUTION RISK OF ELEC TRIC SHOCK DO NOT OPEN NO U SER SERVICEABLE PARTS INSIDE www dimplex com amp IMPORTANT INSTRUCTIONS damage to the heater To prevent a possible fire do not block air intake or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked 2 All electrical heaters have hot and arching or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the unit will be exposed to flammable vapours 3 Do not modify the fireplace Use it only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Avoid the use of an extension cord Extension cords may overheat and cause a risk of fire If you must use an extension cord the cord must be No 14 AWG minimum size and rated no less than 1875 Watts 5 Do not burn wood or other materials in the fireplace Do not strike the fireplace glass 2 Always use a certified electrician should new circuits or outlets be required Always use properly grounded fused and polarized outlets Disconnect all power supply before performing any cleaning maintenance or relocation of the unit When transporting or storing the unit and cord keep in a dry place free from e
5. Purifire includes a high efficiency filter to help improve the quality of air Press the G button P to turn the Purifire function on When the Purifire function is on the Purifire symbol will flash When off the symbol will be solid The default setting for the Purifire is set at low speed Press the Q or the R buttons to change between low and high speeds Press the G button to turn the Purifire function off H Flame amp Heat On Off Button Press the H button 4 to turn the Flame Heat function on When B is higher then A the heat will come on To turn the heat off lower the B so that it s setting is lower then the A The default temperature setting is 72 F 22 C NOTE When using the remote control the heater runs on a thermostat Press the J or I buttons to adjust the set temperature Once the desired set temperature is reached the heater will turn off The heater will cycle on and off to maintain the desired set temperature Child Lock Figure 6 1 Depress tab on the battery cover on the back of the remote transmitter and remove the battery cover 2 Move Child Lock tab to the right to lock the remote transmitter 3 Move Child Lock tab back to the left to unlock the remote transmitter 4 Replace the battery cover 13 Operation NOTE To temporarily unlock the remote transmitter press in order I then J then K When the remote transmitter s backlight is illuminat
6. a hard surface to dislodge any loose dirt or debris and then clean with water No soap or cleaning products are recommended The filter size is 20 x 10 x 1 inches rated at MERV 10 To replace filter 1 Remove fireplace from mantel 2 Filter can be accessed from the top rear of the unit Figure 9 3 Grasp filter and slide filter straight up 4 Replace or clean filter NOTE If after market air filter is used ensure it is installed according to the manufacturer s recommended instructions Figure 9 Purifire Filter Al L3 Glass Cleaning The glass is cleaned in the factory during the assembly operation During shipment installation handling etc the clear door may collect dust particles these can be removed by dusting lightly with 17 P di Maintenance a clean dry cloth To remove fingerprints or other marks the clear door can be cleaned with a damp cloth The clear door should be completely dried with a lint free cloth to prevent water spots To prevent scratching do not use abrasive cleaners or spray liquids on the clear door surface Warranty Five Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to the following model of your newly purchased Dimplex electric fireplace DFB8842 and to newly purchased Dimplex fireplace surrounds mantels and trims This limited warran
7. ad and save these instructions amp CAUTION Read all instructions and warnings carefully before starting installation Failure to follow these instructions may result in a possible electric shock fire hazard and will void the warranty Please record your model and serial numbers below for future reference model and serial numbers can be found on the Model and Serial Number Label of your fireplace Serial Number SERIAL No XX idi Number Part Number AIR HEATER CHAUFFE AI CALENTADOU DE AIRE Won A MODEL NO UL PART 148Y E7416 MADE IN ENTS 4 965707 AND 8 642 588 CANADIAN PATENT 2 175 442 FURTHER PATENTS PENDING ION K OF ELECTRIC SHOCK DO NOT OPEN NO USER SERMCEABLE PARTS INSIDE AUCUNE PIECE REPARABLE PAR L UTILISATEUR A L INTERIEUR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR ZIZI Ll Contact us at OR STOP NO NEED TO RETURN TO THE STORE Questions with operation or assembly Require Parts Information Product Under Manufacturer s Warranty www dimplex com customer_support For Troubleshooting and Technical Support Lnd G Toll Free 1 888 DIMPLEX 1 888 346 7539 Monday to Friday 8 00 a m to 4 30 p m EST Please have your model number and product serial number ready See above amp IMPORTANT INSTRUCTIONS When using electrical appliances basic precautions should
8. b on the battery cover on the back of the remote transmitter and remove x battery cover T Child Lock Batteries 2 Install two 2 AAA batteries into the remote control included 3 Ensure child lock is in the position 4 Replace the battery cover NOTE When the BAT symbol is present on the remote control it is recommended to replace the batteries promptly to maintain full functionality of the remote fireplace The remote transmitter has a battery backup time of only several hours Initializing Reprogram ming the Remote Control 1 Plug cord into 120 Volt wall outlet 2 Ensure the Main On Off Switch of the fireplace Figure 3A is in the On position 3 Set the 3 Position Manual Control Figure 3B to the Remote position left position 4 Press and hold the Initialization Button on the unit Figure 3C 5 While holding the Initialization Button press the Flame Heat On Off button or the Purifire On Off B button on the remote control transmitter Figure 5 6 Release the Initialization Button on the unit 7 Press the Flame Heat On Off button amp to turn the Flame Heat function on or press the Purifire On Off button P to turn the Purifire function on 11 Operation Figure 5 A Room Temperature Set Temperature Light Dimmer Contr
9. counter clockwise 8 Insert new bulbs and screw in clockwise 9 Install the Log Set Assembly by placing the front bottom edge of the Ember Bed in the track behind the control panel Once in place push down on the back edge of the Ember Bed until the rear tab snaps into place under the Mirror Figure 8 NOTE Ensure the Log Set Assembly is installed tightly under the back ledge to prevent light leakage 10 Slide front glass back into position and attach trim Upper Light Bulb Requirements Quantity of two 2 clear chandelier or candelabra bulbs with an E 12 small socket base 15 Watt rating Do not exceed 15 Watts per bulb To access the upper light bulb area 1 Slide fireplace out of mantel 2 Remove four 4 Phillips screws from right side of trim Figure 7 3 Remove trim www dimplex com oe Maintenance 4 Slide glass to the right side of the fireplace to remove Figure 7 5 Remove Upper Light Bracket Figure 7 6 Upper bulbs are located in the upper left and upper right corners of the fireplace 7 Unscrew bulbs counter clockwise 8 Insert new bulbs and screw in clockwise 9 Re install Upper Light Bracket 10 Slide front glass back into position and attach trim Purifire Filter The Purifire filter supplied in your fireplace is reusable and washable The filter should be cleaned or replaced on average once a year To clean the filter gently tap filter on
10. e been tested and inspected prior to shipment Subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 5 years from the date of the first purchase of such products as follows a a repair or replacement warranty on defective products or parts including in home services for the first year following the date of first purchase and b thereafter a replacement of parts warranty on defective products and parts with no in home services for the 4 year period commencing on the first anniversary of first purchase and ending on the fifth anniversary of the date of first purchase Dimplex fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment and subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products Warranty services do not include in home services The above section is a summary only of your warranty rights Please review the remaining provisions of this warranty for your specific rights The limited 5 year warranty period for products other than fireplace surrounds mantels and trims and the limited 1 year warranty period for fireplace surrounds mantels and trims also applies to any implied warranties that may exist under appl
11. ed the Child Lock is bypassed When the backlight is off the Child Lock is re activated Figure 6 cm a Z 35 Unlocked Child Lock Locked Switch es Frequency Interference If the fireplace does not respond properly to the remote control the remote operating frequency may have to be reset The remote control can send another frequency code to the circuit board to eliminate interference 1 Simultaneously press the O Sleep Timer Down button and the Q button on the remote control COD will appear in place of the sleep timer digits Release the O button and the Q button Press the Initialization button on the unit Figure 4C Press the H amp button on the remote Your remote will now have a different frequency communicating with the fireplace www dimplex com oe Maintenance amp WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electric shock or damage to persons Light Bulb Replacement Allow at least five 5 minutes for light bulbs and heater to cool off before touching bulbs to avoid accidental burning of skin Light bulbs need to be replaced when you notice a dark section of the flame There are three 3 under the Log Set which generate the flames and embers and two 2 bulbs above the log that illuminate the log exterior
12. icable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser What this limited warranty does not cover This limited warranty does not apply to products that have been repaired except by Dimplex or its authorized service representatives or otherwise altered This limited warranty does further not apply to defects resulting from misuse abuse accident neglect incorrect installation improper maintenance or handling or operation with an incorrect power source What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1 888 DIMPLEX 1 888 346 7539 or 1367 Industrial Road Cambridge Ontario Canada N1R 7G8 Please 19 SG Warranty have proof of purchase catalogue model and serial numbers available when calling Limited warranty service requires a proof of purchase of the product What Dimplex will do in the event of a defect In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during i the 5 year limited warranty period for products other than fireplace surrounds mantels and trims and ii the 1 year limited warranty period for surrounds mantels and trims you have the following rights Limited warranty service will be performed solely by dealers o
13. in fire or mix with used or other battery types may explode or leak causing injury amp CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void user s authority to operate the equipment www dimplex com SE Site Selection and Preparation This section provides instructions for selecting a location and preparing the site to install the fireplace into your Dimplex mantel surround 1 Select a suitable location that is not susceptible to moisture and is away from drapes furniture and high traffic 2 For ease of electrical hook up you may wish to locate the fireplace near an existing outlet refer to NOTE 1 3 Store the fireplace in a safe dry and dust free location NOTE 1 A15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedicated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker amp CAUTION Clearance for air circulation beneath the fireplace insert is provided by six 6 rubber feet Do not install the fireplace insert directly on carpet or similar surfaces which may restrict air circulation If installing the fireplace in a carpeted area place a one piece solid flat surface under the fireplace inser
14. ives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty 22 www dimplex com s Replacement Parts Log Set Assembly 00 00 eee eee 0438550100RP Flicker Motor 3000240200KIT Heater Assembly 00000 c eee eee eee 2200490600RP CutOUb e Ta ia ace e Rei hein aar REA wk Al 2300270300RP Main On Off Switch llle 2800070700RP Remote Switch Board 20 0 eee 3000300300RP Cord Sel coe enc rx ett kar Ud o eie a 4100040500RP Lower Light Wire Harness send with below 2500400100RP Lower Centre Socket send with above 2500150200RP Upper Light Wire Harness 2500400200RP MINOR err REE ner a Ro spar Re phia 5900680100RP Front Glass 2d es VE eR a a a a A 5900310500RP Remote Transmitter 2 2 0005 3000300100RP Remote Receiver elslseeelee seen 3000300200RP Flicker ROU o rbd rad 5900080700RP Purfire M Filter ioc er Re ERE RR 0439060100RP Switch Housing Door 0020 0 eee 0439210200RP Wire Harness 1 socket 0000005 2500150200RP Fireplace Foot 00 002 eee eae 8800090100RP X Dimplex Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8
15. ncluding without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s business and all labour costs Such costs shall not be the responsibility of Dimplex Oncsite or in home services not provided under this warranty may be performed at the purchaser s specific request and expense at Dimplex s then current rates for Such services What Dimplex and its dealers and service agents are also not responsible for IN NO EVENT WILL DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL DIMPLEX OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT 21 GS Warranty SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER How State and Provincial law apply This limited warranty g
16. ol Flame Speed Control Sleep Timer Purifire Purifire On Off Flame amp Heat On Off Temperature Down Temperature Up Dimmer Down Dimmer Up Flame Speed Down Flame Speed Up Sleep Timer Down Sleep Timer Up Purifire Speed Down Purifire Speed Up J O voz ar ASC TA 1MWVO DW Remote Control Functions SC Dimplex B Set Temperature Press H button 4 to turn fireplace on Press J to raise thermostat or to lower the thermostat Press both J and I to change F to C C Light Dimmer Control While the fireplace is running repeatedly press the L or K button to increase or decrease the brightness of the upper lights D Flame Speed Control B While the fireplace is running press the N button to increase the speed of the flame or press the M to decrease the speed of the flame 12 www dimplex com Operation E Sleep Timer The Sleep Timer automatically shuts off the fireplace after a preset time from 30 minutes to 8 hours During fireplace operation to set the sleep timer press the P button Set the timer from 30 minutes through 8 hours The fireplace will automatically turn off when the sleep timer reaches zero 0 minutes The sleep timer can be cancelled at any time by pressing the O button repeatedly until the sleep timer displays 0 Se ZZ po m F Purifire The
17. on The flame effect and heater are turned ON simultaneously When the manual control is in the Flame amp Heat position the heater does not run on the remote operated thermostat C Initialization Button Used to synchronize remote control NOTE When the manual control switch is in the Flame and Flame amp Heat positions the fireplace unit will not operate with the remote control Figure 3 EET A B C Resetting The Temperature Cutoff Switch The heater is protected with a safety device to prevent overheating Should the heater overheat an automatic cut out will turn the heater off and it will not come back on without being reset It can be reset by switching the ON OFF Switch to OFF and waiting five 5 minutes before switching the unit back on A CAUTION If you need to continuously reset the heater unplug the unit and call Dimplex North America Limited at 1 888 346 7539 Have the product Model and Serial Numbers ready when calling www dimplex com Operation Remote Control The remote control has a range of approximately 50 feet 15 25 m It does not have to be pointed at the fireplace and can pass through most obstacles including walls It is supplied with 243 independent frequencies to prevent interference with other units Battery Installation Figure 4 Figure 4 1 Depress the ta
18. r service agents of Dimplex authorized to provide limited warranty services For products other than surrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective product or part without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part This limited warranty entitles the purchaser to on site or in home warranty services Accordingly Dimplex will be responsible for all labour and transportation costs associated with the repair or replacement of the product or part except as follows i charges may be levied for travel costs incurred to travel to the purchaser s site where the product is located if the purchaser s site is beyond 30 miles 48 km from the closest service depot of Dimplex s dealer or service agent and ii the purchaser is solely responsible for providing clear access to all serviceable parts of the product For products other than surrounds mantels and trims for the period commencing at 12 01 a m on the day after the first anniversary of the first purchase and ending at midnight on the fifth anniversary of the date of first purchase this limited wa
19. rranty entitles the purchaser to replacement parts only without charge If Dimplex is unable to replace such part or if replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of replacement choose to refund the purchase price for such part The purchaser shall not be entitled to on site or in home warranty 20 www dimplex com GS Warranty services The purchaser shall be responsible for all expenses incurred for the removal of the part and installation of the replacement part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s place of business and all labour costs Such costs shall not be the responsibility of Dimplex e For surrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective surrounds mantels and trims or part thereof without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part The purchaser shall not be entitled to on site or in house services The purchaser is responsible for all expenses incurred for repair or replacement of such product or part i
20. s IMPORTANT If not using a Dimplex mantel the firebox must be installed in an enclosure with the following MINIMUM internal opening dimensions Figure 2 New Wall Construction 1 Select a suitable location that is not susceptible to moisture and is away from drapes furniture and high traffic 2 Place the fireplace in the desired location to see how it will look in the room www dimplex com Fireplace Installation 3 Mark the desired location Option 2 A new outlet can be on the floor and store the installed inside the new frame fireplace in a safe dry and construction duets location Plug the unit directly into a 15 4 Use studs to frame an opening Amp 120 Volt outlet of 30 inches 781 mm wide X 25 inches 654 mm high X 10 inches 273 mm deep Option 1 The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace Figure 2 254 654 mm 30 24 lt 781 mm 1034 273 al mm Operation Electric Fireplace Manual Controls The manual controls for the fireplace are located in the lower right hand corner Figure 3 A Main On Off Switch Supplies power to the 3 position manual control switch B 3 Position Manual Control Switch Remote right position The unit is operated with the remote control Flame center position The flame effect is turned ON Flame amp Heat left positi
21. t Ensure that all six of the insert s feet rest securely on this surface WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician Fireplace Installation Figure 1 31 34 797 mm 730 Ys 768 mm 648 mm 26 670 y mm Y L For dimensions of the firebox insert with and without the trim refer to Figure 1 The fireplace does not require any additional venting NOTE 1 A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedicated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker Install the fireplace assembly into the mantel refer to mantel assembly instruction
22. ty applies only to purchases made in any province of Canada except for Yukon Territory Nunavut or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska This limited warranty applies to the original purchaser of the product only and is not transferable Products excluded from this limited Fireplace Surface Clean ing Use damp warm cloth only to clean painted surfaces Do not use abrasive cleaners on glass surface or spray liquids directly onto any surface warranty Light bulbs and Purifire filters are not covered by this limited warranty and are the sole responsibility of the owner purchaser Products purchased in Yukon Territory Nunavut Northwest Territories Hawaii or Alaska are not covered by this limited warranty Products purchased in these States provinces or territories are sold AS IS without warranty or condition of any kind including without limitation any implied warranties or conditions of merchantability or fitness for a particular purpose and the entire risk of as to the quality and performance of the products is with the purchaser and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair 18 www dimplex com Warranty What this limited warranty covers and for how long Products other than fireplace surrounds mantels and trims covered by this limited warranty hav
23. xX Dimplex Better solutions through innovation Owner s Manual Model DFB8842 IMPORTANT SAFETY INFORMATION Always read this manual first before attempting to install or use this fireplace For your safety always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage To view the full line of Dimplex products please visit www dimplex com 7207500200R05 Table of Contents Welcome amp Congratulations 3 A IMPORTANT INSTRUCTIONS 4 SE Site Selection and Preparation T Fireplace Installation sce Rt ERI 8 Mr Operation 25242424485 4 pute 98 6 Pe aed 10 d Maintenance La ae iC RR ACRI GEN qn de d 15 SG WANE sse NM CNN ON 18 Replacement Parts ERE 23 Always use a qualified technician NOTE Procedures and or service agency to repair techniques that are this fireplace considered important enough to emphasize amp CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury or death 2 www dimplex com Welcome amp Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex the world leader in electric fireplaces Please carefully re
24. xcessive vibration and store so as to avoid damage SAVE THESE INSTRUCTIONS amp IMPORTANT INSTRUCTIONS NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna ncrease the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device 4 WARNING Remote control contains small batteries Keep away from children If swallowed seek medical attention immediately amp WARNING Do not install battery backwards charge put
Download Pdf Manuals
Related Search