Dimplex DF3215NH User's Manual
Contents
1. NOTE A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedicated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician Site Selection And Preparation This section provides instructions for selecting a location and preparing the site to install the fireplace into your Dimplex mantel surround 1 Select a suitable location that is not susceptible to moisture and is away from drapes furniture and high traffic 2 For ease of electrical hook up you may wish to locate the fireplace near an existing outlet refer to NOTE 1 3 Store the fireplace in a safe dry and dust free location2. NOTE The dimensions of the fireplace are 36 4 inches 927 mm wide X 31 inches 806 mm high X 13 inches 330 mm deep The viewing area is 32 inches 813 mm wide and 28 715 mm high The fireplace does not require any additional venting Fireplace Installation 1 Install the Bi fold doors to the fireplace IMPORTANT Bi fold doors MUST be installed to the firebox prior to installing firebox to mantel Bi fold Door Installation Figure 2 Figure 2 gt x O 5 5 Q Door Bottom a Screw Spacer Ledge i Remove the Bi fold doors from packaging ii Remove the Philips head screw and the door spacer from the bottom edge of the Bi fold door opposite of the door handle iii Insert the door spacer into the bottom panel ledge mounting hole iv Insert the top edge of the Bi fold door into the top door track on the fireplace v Secure the Bi fold door to unit with supplied screw using a short handled screwdriver NOTE If short handled screwdriver is not available tilt the unit back vi Repeat steps 2 5 for the other side 2 Install the fireplace assembly into the mantel refer to Dimplex mantel assembly instructions 8 IMPORTANT If not using a Dimplex mantel the fireplace must be installed in an enclosure with the following MINIMUM internal opening dimensions 32 inches 813 mm wide x 31 inches 806 mm h
3. NOTE To temporarily unlock the remote transmitter press in order Temperature Down then J Temperature Up then K Dimmer Down Firelight Off When the remote transmitter s backlight is illuminated the Child Lock is bypassed When the backlight is off the Child Lock is re activated Frequency Interference If the fireplace does not respond properly to the remote control the remote operating frequency may have to be reset The remote control can send another frequency code to the circuit board to eliminate interference 1 Simultaneously press the O Slow Start Fading Embers Off button and the Q Purifire Low Speed button on the remote control 2 CODE will appear 3 Release the Slow Start Fading Embers Off button and the Purifire Low Speed button 4 Press and hold the Initialization Button on the unit Figure 4 5 Press the G Flame amp Heat On Off amp button on the remote and release the Initialization Button Your remote will now have a different frequency communicating with the fireplace Maintenance WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electric shock or damage to persons Light Bulb Replacement Allow at least five 5 minutes for light bulbs to cool before touching bulbs to avoid accidental burning of skin Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the l
4. Z j og SE Dimplex 12 Remote Control Functions Figure 6 A B C D E F G H J Room Temperature K Dimmer Down Firelight Off Set Temperature L Dimmer Up Firelight On Dimmer Firelight Control M Flame Speed Down Flame Speed Control N Flame Speed Up Slow Start Fading Embers O Slow Start Fading Embers Control Off Purifire Speed P Slow Start Fading Embers Flame amp Heat On Off On Timer Cycle Purifire On Off Q Purifire Low Speed l Temperature Down R Purifire High Speed Temperature Up The set temperature buttons are not operational on the DF3215NH model B 1 2 3 4 fireplaces Set Temperature Press G Flame amp Heat On Off button to turn the fireplace on Press J Temperature Up to raise thermostat Press Temperature Down to lower the thermostat Press both J Temperature Up and Temperature Down to change F to C Not applicable on DF3215NH model fireplaces C 1e Dimmer Firelight Control Press the G Flame amp Heat On Off button to turn the Flame amp Heat on Repeatedly press the L Dimmer Up Firelight On or K Dimmer Down Firelight Off button to increase or decrease the brightness of the upper lights To activate the Firelight continue pressing L Dimmer Up Fire light On until the Firelight On icon is shown on the display screen To shut the Firelight off continue pressi
5. Road Cambridge ON Di m lex Canada N1R 7G8 1 888 346 7539 e www dimplex com 2010 Dimplex North America Limited 22
6. use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 8 Do not run the cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 9 To disconnect the unit turn the controls off then remove the plug from the outlet 10 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage to the heater 11 To prevent a possible fire do not block air intake or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked not applicable on DF3215NH model fireplaces 12 All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the unit will be exposed to flammable vapors not applicable on DF3215NH model fireplaces 13 Do not modify the electric fireplace Use it only as described in this 4 manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 14 Avoid the use of an extension cord Extension cords may overheat and cause a risk of fire If you must use an extension cord the cord must be No 14 AWG minimum size and rated no less than 1875 Watts 15 Do not burn wood or other materials in the
7. 20 inches x 10 inches 18 X 1 inch rated at MERV 10 If using an after market filter follow the manufacturers recommended replacement instructions To replace filter 1 Open the Bi fold doors 2 Remove the three 3 mounting screws Bracket from the Air Filter i Bracket 3 Remove the Air Filter Bracket assembly from the Mounting firebox Screws 4 Slide Filter out of Air Filter Bracket 5 Replace filter and Figure 11 Air Filter p reassemble in reverse order as above NOTE If after market air filter is used ensure it is installed according to the manufacturer s recommended instructions Glass Cleaning The glass is cleaned in the factory during the assembly operation During shipment installation handling etc the glass may collect dust particles these can be removed by dusting lightly with a clean dry cloth To remove fingerprints or other marks the glass can be cleaned with adamp cloth To prevent scratching do not use abrasive cleaners or spray liquids on the glass surface Fireplace Surface Cleaning Use a cloth dampened with warm water only to clean painted surfaces of the electric fireplace Do not use abrasive cleaners 19 Ten Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to the following model of your newly purchased Dimplex electric fireplace DF
8. 3215 DF3215NH and to newly purchased Dimplex fireplace surrounds mantels and trims This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory Nunavut or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska This limited warranty applies to the original purchaser of the product only and is not transferable Products excluded from this limited warranty Light bulbs and Purifire filters are not covered by this limited warranty and are the sole responsibility of the owner purchaser Products purchased in Yukon Territory Nunavut Northwest Territories Hawaii or Alaska are not covered by this limited warranty Products purchased in these States provinces or territories are sold AS IS without warranty or condition of any kind including without limitation any implied warranties or conditions of merchantability or fitness for a particular purpose and the entire risk of as to the quality and performance of the products is with the purchaser and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair What this limited warranty covers and for how long Products other than fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment Subject to the provisions of this warranty Dimplex warrants such products to be free from def
9. 8 Insert new bulbs 9 Install the left side of the flame rod to the mounting bracket 10 Reconnect the Log Set LED Wire Harness 11 Replace the Log Set by inserting the rear tab of the Figure 9 Ember Bed under the mirror and push down on the front Back ay Log edge of the Ember Bed until it Ledge Ember snaps into place Figure 9 bg Bed NOTE Ensure the Log Set is installed tightly under the back Rear Gide Section ont ledge to prevent light leakage Tab Edge 12 Close the Bi fold doors Upper Light Bulb Requirements Quantity of two 2 clear chandelier or candelabra bulbs with an E 12 guren small socket base 25 Watt rating All Upper Light Do not exceed 25 Watts per bulb To access the upper light bulb area 1 Open the Bi fold doors a 2 Remove upper light bracket with a screwdriver Figure 10 3 Replace bulb 4 Reassemble in the reverse order as above Upper Light Bracket Purifire Filter Figure 11 The Purifire7M filter supplied in your fireplace is reusable and washable The filter should be cleaned or replaced on average once a year To clean the filter gently tap filter on a hard surface to dislodge any loose dirt or debris and then clean with water No soap or cleaning products are recommended The filter size is
10. e remote control Flame center position The flame effect is turned on Flame amp Heat right position The flame effect and heater are turned on simultaneously When the manual control is in the Flame amp Heat position the heater does not run on the remote operated thermostat When the heater is on the red indicator light is activated on the firebox and the fan and heater are running on low NOTE When the manual control switch is in the Flame and Flame amp Heat positions the fireplace unit will not operate with the remote control 10 Flame only function of DF3215NH Resetting The Temperature Cutoff Switch Should the heater overheat an automatic switch will turn the heater off and it will not come back on without being reset The temperature cutoff switch can be reset by unplugging the unit waiting five 5 minutes and plugging the unit back in A CAUTION If you need to continuously reset the heater unplug the unit and call Dimplex North America Limited at 1 888 346 7539 for technical support Not applicable on DF3215NH model fireplaces Remote Control The remote control has a range of approximately 50 feet 15 25 m It does not have to be pointed at the fireplace and can pass through most obstacles including walls It is supplied with 243 independent frequencies to prevent interference with other units Battery Installation Figure 5 1 Depress the tab on the battery cover on the back of th
11. e remote transmitter and remove battery cover 2 Install two 2 AAA batteries into the remote control included 3 Ensure child lock is in the unlocked position 4 Replace the battery cover Figure 5 NOTE When the B gt symbol is present i on the remote control it is recommended to replace the batteries promptly to maintain Child Lock Batteries full functionality of the remote fireplace The remote transmitter has a battery backup time of only several hours 11 Initializing the Remote Control 1 2 Plug cord into 120 Volt wall outlet Ensure the Main On Off Switch of the fireplace Figure 4 is in the On position Set the 3 Position Manual Control Figure 4 to the Remote position left position Press and hold the Initialization Button on the unit Figure 4 While holding the Initialization Button press the Flame Heat On Off button or the Purifire On Off B button on the remote control transmitter Figure 6 Release the Initialization Button on the unit Press the Flame Heat On Off button 4 to turn the Flame Heat function on or press the Purifire On Off button B to turn the Purifire function on Figure 6 O7 s Y 7 9 M i Pras
12. ects in material and workmanship for a period of 10 years from the date of the first purchase of such products as follows a a repair or replacement warranty on defective products or parts including in home services for the first year following the date of first purchase and b thereafter a replacement of parts warranty on defective products and parts with no in home services for the 9 year period commencing on the first anniversary of first purchase and ending on the tenth anniversary of the date of first purchase Dimplex fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment and subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products Warranty services do not include in home services The above section is a summary only of your warranty rights Please review the remaining provisions of this warranty for your specific rights The limited 10 year warranty period for products other than fireplace surrounds mantels and trims and the limited 1 year warranty period for fireplace surrounds mantels and trims also applies to any implied warranties that may exist under applicable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser What this limit
13. ed warranty does not cover This limited warranty does not apply to products that have been repaired except by 20 Dimplex or its authorized service representatives or otherwise altered This limited warranty does further not apply to defects resulting from misuse abuse accident neglect incorrect installation improper maintenance or handling or operation with an incorrect power source What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1 888 DIMPLEX 1 888 346 7539 or 1367 Industrial Road Cambridge Ontario Canada N1R 7G8 Please have proof of purchase catalogue model and serial numbers available when calling Limited warranty service requires a proof of purchase of the product What Dimplex will do in the event of a defect In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during i the 10 year limited warranty period for products other than fireplace surrounds mantels and trims and ii the 1 year limited warranty period for surrounds mantels and trims you have the following rights e Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services For products other than surrounds mantels and trims for the period ending at midnight on the first anniversary of the date of fi
14. efund the purchase price for such part The purchaser shall not be entitled to on site or in home warranty services The purchaser shall be responsible for all expenses incurred for the removal of the part and installation of the replacement part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s place of business and all labour costs Such costs shall not be the responsibility of Dimplex e For surrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion 21 either repair or replace such defective surrounds mantels and trims or part thereof without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part The purchaser shall not be entitled to on site or in house services The purchaser is responsible for all expenses incurred for repair or replacement of such product or part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s business and all labour costs Such costs shall not be the responsibility of Dimplex On site or in home services not provided under this warranty may be performed a
15. electric fireplace 16 Do not strike the fireplace glass 17 Always use a certified electrician should new circuits or outlets be required 18 Always use properly grounded fused and polarized outlets 19 Disconnect all power supply before performing any cleaning maintenance or relocation of the unit 20 When transporting or storing the unit and cord keep in a dry place free from excessive vibration and store so as to avoid damage CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE SAVE THESE INSTRUCTIONS NOTE Procedures and techniques that are considered important enough to emphasize A CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment a WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury illness or death NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the in
16. igh x 13 inches 343 mm deep and in such a way that the plug and outlet can be accessed Figure 3 Figure 3 ae 13 1 2 3 Removable mounting hardware must be used when installing this unit into a new wall application this unit must be able to be removed from the opening to access the plug and outlet as well as for servicing purposes A custom trim may be used permitting easy and non destructive removal 4 Plug the unit into a 15 Amp 120 Volt outlet If the cord does not reach you may use an extension cord rated for a minimum of 1875 Watts WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge Also ensure the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Operation Electric Fireplace Manual Control The manual controls for the fireplace are located in the upper right hand corner Figure 4 Figure 4 EA f at ri H wm o Main aie 083 On Off Et DAL Initialization HS Ses IE a Button MI o JHE e O o m Indicator 3 Position 7 C Light Manual Control Main On Off Switch Supplies power to the 3 Position Manual Control Switch 3 Position Manual Control Switch Remote left position The unit is operated with th
17. m The world leader x D m p lex in electric fireplaces Owner s Manual Model Numbers DF3215 DF3215NH Quality checked by Serial Number Model Number Part Number Valued Customer Thank you and congratulations for purchasing a Dimplex electric fireplace Over the years valuable memories will occur around the warmth and comfort of your hearth Thank you for allowing our product to be the backdrop for those special moments 7207030100rev11 QUICK REFERENCE GUIDE 1 Before using the fireplace verify e Are the circuit breakers for the unit on e Are the light bulbs loose to check follow the instructions for replacing the light bulbs under the maintenance section of this manual The heater may emit a slight harmless odor when first used This odor is a normal condition caused by the initial heating of internal heater parts The information regarding the model of your unit can be found on the rating plate located inside the unit See Page 6 for an illustration on how to locate the rating plate If you have any questions or concerns regarding the operation of your fireplace contact Dimplex customer service at 1 888 DIMPLEX 1 888 346 7539 before returning the product to the point of purchase CONTENTS Important Instructions PAGE 4 Model and Serial Number Information PAGE 6 Site Selec
18. ng the K Dimmer Down Firelight Off button until the Firelight Off is shown on the display 13 D Flame Speed Control 1 Press the G Flame amp Heat On Off button to turn the Flame amp Heat on 2 Press the N Flame Speed Up button to increase the speed of the flame 3 Press the M Flame Speed Down button to decrease the speed of the flame E Slow Start Fading Embers Control The Slow Start function simulates a starting fire The function is automatically programmed for 30 seconds and the timer setting cannot be changed The Fading Embers function simulates a fire going out The Fading Embers timer can be set to 1 5 or 10 minutes 1 Press the P Slow Start Fading Embers On Timer Cycle button to turn the Slow Start Fading Embers function on 2 Press the P Slow Start Fading Embers On Timer Cycle button repeatedly to set the Fading Embers timer to 1 5 or 10 minutes 3 Press the O Slow Start Fading Embers Off button to turn the Fading Embers timer function off F Purifire Speed When the Purifire function is on the Purifire symbol will flash When off the symbol will be solid The default setting for the Purifire is set at low speed 1 Press the H Purifire On Off button to turn the Purifire function On 2 Press the Q Purifire Low Speed to decrease the Purifire speed or the R Purifire High Speed to increase the speed 3 Press the H Purifire On Off button to turn
19. og ember bed exterior disappears There are four 4 bulbs under the log set which generate the flames and embers and two 2 bulbs above the log that illuminate the log exterior 16 Lower Light Bulb Requirements Quantity of four 4 clear chandelier or candelabra bulbs with an E 12 small socket base 60 Watt rating Example GE 60BC or Philips 60 CTC Do not exceed 60 Watts per bulb Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of times you need to open the unit to replace light bulbs Care must be taken when removing the Log Set as the Log Set contains LED s and wires To access the lower light bulb area Figure 8 1 Open the Bi fold doors 2 Pull the front edge of the plastic Ember Bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the mirror IMPORTANT Only handle the Log Set by the Ember Bed NOTE Log Set fits Figure 8 tightly into firebox some force may be necessary Light Bulbs to remove 3 Set Log Set in front of LED Wire firebox Harness 4 Disconnect the Log Set LED wire harness from unit 5 Lift the left side of the flame rod out of the Bed Lm Ras mounting bracket 6 Examine the bulbs to determine which bulbs require replacement 7 Unscrew bulbs counter clockwise 17
20. rst purchase Dimplex will in its sole discretion either repair or replace such defective product or part without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part This limited warranty entitles the purchaser to on site or in home warranty services Accordingly Dimplex will be responsible for all labour and transportation costs associated with the repair or replacement of the product or part except as follows i charges may be levied for travel costs incurred to travel to the purchaser s site where the product is located if the purchaser s site is beyond 30 miles 48 km from the closest service depot of Dimplex s dealer or service agent and ii the purchaser is solely responsible for providing clear access to all serviceable parts of the product For products other than surrounds mantels and trims for the period commencing at 12 01 a m on the day after the first anniversary of the first purchase and ending at midnight on the tenth anniversary of the date of first purchase this limited warranty entitles the purchaser to replacement parts only without charge If Dimplex is unable to replace such part or if replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of replacement choose to r
21. t the purchaser s specific request and expense at Dimplex s then current rates for such services What Dimplex and its dealers and service agents are also not responsible for IN NO EVENT WILL DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL DIMPLEX OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER How State and Provincial law apply This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty c UL us Dimplex North America Limited m 1367 Industrial
22. terference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to 5 which the receiver is connected Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Model And Serial Number Information If you have any questions about our produ cts please have the product model and serial numbers available upon calling Dimplex customer service To locate the model and serial number see below Figure 1 Record the Part Number Model Number a nd Serial Number on the front cover of this manual for future reference Figure 1 Part Number 1 ANADIA F THE ARTES ADENT T ATIS VATI LTS VOLTIO FREQUE TI ISK OF ELECTRIC SHOCK T OPE ER SERVICEABLE PARTS INSIDE ATTENTI ISQUE DE DECHARGE ELECTRIQUE Et Is E PIECE EPARABLE PAR LUTLISATEUR A LINTERIE ECAUCI IE E CHOQUE ELE TI ABRI HAY E EL USUARIO PUEDA REPARA AIR HEATE HE FFE I ALENTA E AIRE TETE ATENT MW ATENTS PENDI ETE une ET Dimplex eus NORTH AMERICA LIVITED USTED 1 iwn EA Serial Number XXXXXXX XXX
23. the Purifire function off NOTE To turn the Flame amp Heat and Purifire off press both control buttons simultaneously G Flame amp Heat On Off Press the G Flame amp Heat On Off button to turn the Flame amp Heat function on When the B Set Temperature is higher then the 14 A Room Temperature the heat will come on To turn the heat off lower the B Set Temperature so that it s setting is lower then the A Room Temperature The default temperature setting is 72 F 22 C NOTE When using the remote control the heater runs on a thermostat Press the J Temperature Up or I Temperature Down button to adjust the B Set Temperature Once the desired set temperature is reached the heater will turn off The heater will cycle on and off to maintain the desired set temperature Not applicable on DF3215NH model fireplaces Child Lock 1 Depress tab on the battery cover on the back of the remote transmitter and remove the battery cover Figure 7 Figure 7 Unlocked Locked jet ra l A AN Child Lock Switch Child Lock 2 Move Child Lock tab to the right to lock the remote transmitter 3 Move Child Lock tab back to the left to unlock the remote transmitter 4 Replace the battery cover 15
24. tion and Preparation PAGE 7 Fireplace Installation PAGE 7 Operation 22c 2 0 2 vbw oe Ee Ee PAGE 10 Maintenance ss ss se EE EE BERE FREE PAGE 16 Warranty ee ys EE we eee ER a ee PAGE 20 IMPORTANT INSTRUCTIONS Retain This User s Guide For Future Reference When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read all instructions before using the electric fireplace 2 The heater is hot when in use To avoid burns do not let bare skin touch hot surfaces The trim around the heater outlet becomes hot during heater operation Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9 m from the front of the unit not applicable on DF3215NH model fireplaces 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended not applicable on DF3215NH model fireplaces 4 Always unplug the electric fireplace when not in use 5 Do not operate any unit with a damaged cord or plug or if the heater has malfunctioned or if the electric fireplace has been dropped or damaged in any manner Return heater to authorized service facility for examination electrical or mechanical adjustment or repair 6 Do not use outdoors 7 The electric fireplace is not intended for
Download Pdf Manuals
Related Search