Delta Electronics TP-PCC01 User's Manual
Contents
1. A MELTA DELTA ELECTRONICS INC 5011669200 TP00 E Ui PCCW INSTRUCTION SHEET st i OF Sc Fe tt AR A Program Copy Card a BERERE a BERET www delta com tw industrialautomation TP PCC01 doesn t support plug and play function Please turn off power before plugging v The voltage for TP PCCO1 is supplied from TP extension slot Please ensure that plug direction is correct when connecting TP PCCO1 to TP extension slot in case danger and damage on the device may occur 0 Introduction Model Name Explanation TP PCCO1 Program Copy Card Series Electrical Specifications Item Model Name TP PCC01 Writing In Data Reserved Life Times for 20 years one hundred thousand times Operation Temperature 0 C 55 C Weight Dimensions 6g 50 85x19 8x10 mm Program Copy Card Functions Compatible firmware version TPO5G TPO8G V1 00 and above Using program copy card functions can copy the whole system parameters and application programs set in one TPO5G TPO8G to another TPO5G TP08G rapidly It can save much time and manpower The operation is described in the following sections TP PCC01 Program Copy Card TP Terminal Panel TPO5G TPO8G Series Ste TP gt TP PCCO1 TP PCC013TP p C2. Esc to Exit Press CLR to Erase TP PCCO1 Press lt Enter gt key to confirm the writing in 5 Press lt Enter gt key to confirm the writing in operation operation m When executing writing in operation m When executing writing in operation TP will display TP will display TP series gt TP PCCO1 TP PCC0O1 TP series Please wait Please wait m Writing in operation is completed m Writing in operation is completed TP will display TP will display Please Remove the TP PCC01 and Please Remove the TP PCC01 and Reboot Reboot Please turn the power of TP off and remove Please turn the power of TP off and remove TP PCC01 from TP At this time all TP programs TP PCCO01 from TP At this time all programs and and system parameters have been copied to system parameters stored in TP PCC01 have TP PCCO1 been copied to TP Turn the power of TP off and then remove Turn the power of TP off and then remove 6 TP PCCO01 when the message Please Remove TP PCCO1 when the message Please Remove the TP PCC01 and Reboot displays on the the TP PCC01 and Reboot displays on the screen of TP screen of TP Dimension and Installation Units mm Note To avoid damage to TP PCC01 when installing TP PCC01 into TP please pay particular attention to the installation direction of TP PCC01 and ensure that the side which there is a switch o
3. n it should be up and toward the user
4. opy TP program to TP PCC01 Copy program in TP PCC01 to TP 1 Turn the switch on the TP PCC01 to Turn the switch on the TP PCC01 to TPTP PCC01 TP PCC01 gt TP 2 Insert the TP PCC01 into the extension slot of TP Insert the TP PCC01 into the extension slot of TP 3 Apply power to TP Apply power to TP m ifthe model type of TP does not match the m _ sif there is no program in TP PCC01 model type of the program set in TP PCC01 TP will display TPO5G program and TP08G program can t be The TP PCCO1 is Empty compatible with each other It means that TP PCC01 gt TP series TPO5G program can t be opened and edited by is illegal TPO8G and TP08G program can t be opened and edited by TP05G either fs TP will display TP series and TP PCC01 is different Press Enter to Confirm TP series gt TP PCCO1 Press Esc to Exit Press CLR to Erase TP PCCO1 m Remove the program m f the model type of TP does not match the TP will display model type of the program set in TP PCC01 TP PCCO1 will be Erased TP will display Press Enter to Confirm TP series and TP PCC01 is different Press ESC to Exit Please Remove the TP PCCO01 and Reboot m fthe model type of TP and the model type of If the model type of TP and the model type of the program set in TP PCC01 is matched the program set in TP PCC01 is matched TP will display TP will display Press Enter to Confirm Press Enter to Confirm TP series gt TP PCCO1 TP PCC0O1 gt TP series Press Esc to Exit Press
Download Pdf Manuals
Related Search