Delta Electronics DTE-2DS User's Manual
Contents
1. a Insert DTE 2DS into the DTE main unit to be copied Enter parameter in initial setting mode and select A and DTE 2DS will read the parameters in the DTE main unit Next you will see on the screen indicating that the copy is successful indicates the copy fails Press to return to operation mode and you will see the present temperature value PV and set temperature value SV b Switch off DTE and withdraw DTE 2DS Insert DTE 2DS into another DTE main unit Enter parameter in initial setting mode and select DTE 2DS will write the parameters into it Next you will see on the screen indicating that the writing in is successful indicates the writing in fails Press to return to operation mode and you will see the present temperature value PV and set temperature value SV Locking the Keys on Panel Lock the keys Enter parameter in operation mode see Setting up Parameters section for details and select the function you desire How does it work indicates locking all the keys on the panel indicates that you can only modify the set temperature value SV and all other functions are locked Press and at the same time to unlock the keys u Analog Output amp Temperature Tuning d Set up analog output tuning Enter parameter and in regulation mode see Setting up Parameters section for details and tune the parameter to the desired output value Lo Temperature offset tuning En2. Set up positive negative proportional output Set it up when in proportional output control Press amp gt Return to set up input type Press lt gt gt Return to auto tuning Types of Input Sensors amp Temperature Range 1 Setup input sensor Enter parameter see Setting up Parameters section for details in initial setting mode and select an input sensor see Table 1 2 Setup temperature range Enter parameter and see Setting up Parameters section for details in initial setting mode to set up the temperature range 3 Setup the position of decimal point Enter parameter see Setting up Parameters section for details in operation mode The position of decimal point will change the temperature range The screen displays only 4 digits therefore you have to set 0 in this parameter if you wish to display values bigger than 999 or smaller than 99 The setting will not be saved Default 1 Input Sensor Type Range Platinum resistance Cu50 50 150 C Platinum resistance Ni120 niel 80 300 C Platinum resistance Pt100 Pe 200 850 C Platinum resistance JPt100 JPL 20 400 C Thermocouple TXK type ma 200 800 C Thermocouple U type H 200 500 C Thermocouple L type ae 200 850 C Thermocouple B type aa 100 1 800 C Thermocouple S type 5 0 1 700 C Thermocouple R type O 1 700 C Thermocouple N type eal 200 1 300 C Thermocouple E ty
3. Setting up Parameters section for details Range Lower limit 100 Set up lower limit Enter parameter in regulation mode see Setting up Parameters section for details Range 0 upper limit For Alarm Application 1 Set up output function only when there is group INB Enter parameter in initial setting mode see Setting up Parameters section for details and set it as alarm output 2 Setup alarm type Enter parameter with INB or and without INB in initial setting mode See Table 2 for more details on the alarm output 3 Setup parameters In operation mode Parameter and Can be set up when there is group INB Parameter and Can be set up when there is no group INB 4 Setup delay alarm output Enter parameter in regulation mode unit second The alarm will be enabled only when the temperature reaches the alarm output condition and the condition remains until the delay time is reached DTE main unit offers 2 groups of alarm output each with 12 alarm modes in the initial setting mode When SV is higher or lower than SV the alarm output will be enabled See the table in the next column for the explanations on the 12 alarm output modes amp Note AL H and AL L include ALIH AL2H and ALIL AL2L SV Alarm Mode Alarm Output Operation 0 No alarm Alarm output is enabled when the temperature reaches upper and lower limits The alarm will be enabled
4. connection Can only be inserted into the Display and Setup Unit slot on DTE main unit u Setting up Parameters Switching modes DTE 2DS is in operation mode when the power is switched on Press to enter regulation mode Press for more than 3 seconds in the operation mode to enter initial setting mode Press in the regulation mode or initial setting mode to return to the operation mode PV SV Displaying the present value and set value Use to change the set value How to set up Use lt gt in the three modes to select the parameter to be set up and to modify the settings Press to save the setting How to switch modes by keys and set up parameters Press forless than 3 secs Press Press for more than 3 secs Press Regulation Mode Operation Mode Initial Setting Mode Regulation Mode PASEI Select channel Operation Mode Initial Setting Mode E UES Set up input type temperature SV Press gt V LO eg Control loop RUN STOP cru Press gt V DL RE Auto tuning Set it up when in PID control and RUN Press gt V Press gt V Press V Regulation Mode EA PID proportional band Set it up when in PID control Press amp V Ea Set up PID Ti value Set it up when in PID control Press lt gt V g Set up PID Td value Set it up when in PID control Press gt V ETH o Set up PD PID control offset When in PID control set up PdoF when Ti 0 AT se
5. output 2 Set up control type Enter parameter in initial setting mode see Setting up Parameters section for details and set it up as ON OFF control 3 Set up parameters In regulation mode Parameters and hysteresis for output 1 can be set up when parameter is set as heating cooling output hysteresis for output 2 can be set up when parameter is set as heating or cooling output You can only set up when and are set as List or at the same time Parameter Can be set up when parameter and are set as control output and the settings in and are different e g output 1 is heating and output 2is cooling For Manual Control Application 1 Set up 2 outputs Enter parameter and in initial setting mode see Setting up Parameters section for details Set up one of the two parameters as or of control output Set up control type Enter parameter in initial setting mode see Setting up Parameters section for details and set it up as manual control 3 Set up parameters In regulation mode Parameter and control cycle for output 1 can be set up when parameter is set as heating or cooling output control cycle for output 2 can be set up when parameter is setas M heating or cooling output Parameter EMH and in operation mode can be set up when parameter is set as heating or cooling output can be set up when parameter is set as
6. when PV exceeds SV AL H or falls below SV A L L OFF _ a OFF A A A AL L SV AL H Alarm output will be enabled when the temperature reaches the ON 2 upper limit The alarm will be enabled when PV exceeds SV AL H Alarm output will be enabled when the temperature reaches the ON l 3 lower limit The alarm will be enabled when PV falls below SV AL L New amp 4 Alarm output will be enabled when PV is between SV AL H oo M and SV AL L acl Sv ACH Alarm output will be enabled when the temperature reaches the ON i 5 absolute value of the upper and lower limits The alarm will be enabled when PV exceeds AL H or falls below AL L Alarm output will be enabled when the temperature reaches the ON A 6 absolute value of the upper limit The alarm will be enabled when PV exceeds AL H Alarm output will be enabled when the temperature reaches the ON O 7 absolute value of the lower limit The alarm will be enabled when PV falls below AL L AL L Upper lower limit standby alarm The alarm will be enabled when ON 8 PV reaches SV and further exceeds SV AL H or falls below OFF i a SV AL L AL L SV AL H 9 Upper limit standby alarm The alarm will be enabled when PV Ba reaches SV and further exceeds SV AL H ent 10 Lower limit standby alarm The alarm will be enabled when PV A reaches SV and further falls below SV AL L AA Upper limit hysteresis alarm The alarm will be enabled when PV ON T 11 exceeds SV AL
7. 2008 08 08 5011673101 DSE1 Aneta http www delta com tw industrialautomation SpE NR ZIZ ZDS DTE Accessory Instruction Sheet Thank you very much for choosing DTE 2DS Please read this instruction sheet before using your DTE 2DS to ensure proper operation Keep this instruction sheet handy for quick reference u Warning 1 Please hold the plastic terminal when installing DTE 2DS to prevent electrostatic discharge ESD 2 Prevent dust or metallic debris from falling into the device and cause malfunction DO NOT modify or uninstall DTE 2DS without being permitted DO NOT use empty terminals 3 When installing DTE 2DS please make sure the power of DTE main unit is switched off and insert DTE 2DS into the correct slot on DTE main unit 4 Make sure you install DTE 2DS correctly before switching on the power otherwise serious damage may occur 5 DO NOT touch the terminals or repair the device when the power is on otherwise an electric shock may occur m Product Outline amp Dimension PV Present temperature value SV Set temperature value AT Auto tuning indicator OUT1 OUT2 Output indicator C F degree Celsius Fahrenheit ALM Alarm indicator i Select and setup Changing page 1 EIEN tuning digits m Electrical Specifications Input power DC 5V Power consumption Max 0 5W A Single row 7 segment LED display two 4 bits Display PV red SV green Keys 4 keys for selecting changing pages and tuning Terminal
8. H The alarm will be disabled when PV falls OFF ss below SV AL L SV AL H Lower limit hysteresis alarm The alarm will be enabled when PV ON er ess 12 falls below SV AL L The alarm will be disabled when PV OFF yoy Ge exceeds SV AL L SV AL H Table 2 E Setting up Communication Set up communication Enter parameter i j Ets and in initial setting mode see Setting up Parameters section for details and select your desired communication settings DTE series temperature controller is able to set up or read communication settings through DTE 2DS Selecting Channel Select channel Enter parameter in regulation mode see Setting up Parameters section for details and select the channel to be monitored 2 How does it work DTE main unit has maximum 8 channels which can be connected to 8 input sensors at the same time The 8 input channels belong to group INA and INB each group with 4 input channels INB is optional accessory therefore if INB is not inserted in DTE DTE will only show 4 channels Setting up Copy Function Set up the function Enter parameter in initial setting mode see Setting up Parameters 3 section for details and select the function you desire How does it work The copy function allows a DTE main unit to copy its parameters including the values set in the parameter and communication settings to another DTE main unit through DTE 2DS Follow the steps below
9. gt V For locking the keys on the panel Press lt gt V For displaying and tuning the value of output 1 Displayed when in PID programmable PID manual control RUN Press gt V PIH For displaying and tuning the value of output 2 Displayed when in PID programmable PID manual control RUN Press lt gt gt Return to target temperature Initial Setting Mode mi Pima Set up upper limit of temperature Press V mi SEES Setup lower limit of temperature Press lt gt V Ceri Select control mode Press GJ v PEE Set up output 1 Heating cooling or proportional output Press lt gt V S 02 Set up output 2 Heating cooling or alarm output Press gt V or BER Without with group INB Set up Alarm 1 mode a Without group INB Set up Alarm 2 mode Press B V Set up copy function Press gt V ic St Select ASCII RTU communication format Press GJ v IC no Set up communication address Press gt V EA Set up communication baud rate Press gt V Set up data length Press amp V Per 5 Set up parity bit Press V Regulation Mode Operation Mode Initial Setting Mode 7 Set up delay time for alarm Eiri Set up stop bit output Press gt V For tuning upper limit of analog output Displayed when in analog output Press lt gt V ie Se ee For tuning lower limit of analog output Displayed when in analog output Press gt V W
10. heating or cooling output For Programmable PID Application 1 Set up 2 outputs Enter parameter and in initial setting mode see Setting up Parameters section for details Set up one of the two parameters as or of control output 2 Set up control type Enter parameter in initial setting mode see Setting up Parameters section for details and set it up as fail programmable control 3 Set up parameters In regulation mode Parameter and Parameter can be set up when parameter is set as 0 Parameter and Wei control cycle for output 1 can be set up when parameter is set as Witi heating or cooling output control cycle for output 2 can be set up when parameter is set as heating or cooling output Parameter and Can be set up when parameter and are set as heating or cooling output The settings in and have to be different Parameter and in operation mode Can be set up when parameter is set as or ieii For Proportional Output Application In this application output 1 has to be analog output 1 2 Set up output function Enter parameter in initial setting mode see Setting up Parameters section for details and set it as fiat proportional output Set up parameters In regulation mode Parameter For Upper Lower Limits of Control Output 1 Set up upper limit Enter parameter in regulation mode see
11. pe g 0 600 C Thermocouple T type mm 200 400 C Thermocouple J type Ss 100 1 200 C Thermocouple K type e 200 1 300 C Table 1 Setting up Control Output For PID Control Application 1 Set up 2 outputs Enter parameter and in initial setting mode see Setting up Parameters section for details Set up one of the two parameters as alsa or of control output 2 Set up control type Enter parameter in initial setting mode see Setting up Parameters section for details and set it up as PID control 3 Set up parameters In regulation mode Parameter Can be set up when parameter is setas MHZ When itd is set as the program will calculate parameters 4 i WEH and automatically and save them Parameter 7 MS anc 3 Parameter and Gig lta can be set up when parameter HS is set as 0 can be set up when is not 0 Parameter and control cycle for output 1 can be set up when parameter is set as heating or cooling output control cycle for output 2 can be set up when parameter is set as Witi heating or cooling output Parameter and Can be set up when parameter and are set as heating or cooling output The settings in and have to be different For ON OFF Control Application 1 Set up 2 outputs Enter parameter and in initial setting mode see Setting up Parameters section for details Set up one of the two parameters as or of control
12. ter parameter in regulation mode and tune the parameter to the displayed temperature value How does it work a Tuning analog output For example if you would like to have accurate 4 20mA of output you can set up output 0 by manual control connect the output to ampere meter and tune parameter making the meter point to 4mA Next set up output 100 by manual control and tune parameter making the meter point to 20mA b Tuning temperature offset This allows the displayed temperature to plus or minus 1 offset value Error Message Error PV Input sensor not connected Internal communication error Output error Input error nm 7 7 Storage error Channel disabled Channel being initialized E cr u How to Install Uncover the panel and insert DTE 2DS to the operation interface slot Remove all the terminal blocks on the panel Insert the terminal blocks back to their positions The content of this instruction sheet may be revised without prior notice Please consult our distributors or download the most updated version at http www delta com tw industrialautomation
13. ts up ioF automatically when Ti 0 Press lt gt V PE Hysteresis for output 1 Set it up when in ON OFF control Press GJ v i es Hysteresis for output 2 Set it up when in ON OFF control Press gt V Pd il Control cycle for output 1 Set it up when in PID programmable PID manual control Press gt V i eS Control cycle for output 2 Set it up when in PID programmable PID manual control Press gt V Pass A Ratio of output 1 amp output 2 when in dual output control Pb2 Pb1 x COEF Set it up when in PID programmable PID dual output Press gt V CO Set up the overlapped area for dual output dead band Set it up when in dual output Press gt V Loc cror For tuning temperature offset ELES Set up upper limit for control output Press gt V Set up lower limit for control output Press gt V Operation Mode Perea Set up start pattern Set it up when in PID control Press lt gt V c co FASS Set up start step Set it up when in PID program control Press lt gt V 5P Set up the position of decimal point Not for thermocouple R S B type Press gt V o MEE Without with group INB Set up upper limit of Alarm 1 Press V Without with group INB Set up lower limit of Alarm 1 Press gt V EEE Without group INB Set up upper limit of Alarm 2 Press lt gt V eS Without group INB Set up lower limit of Alarm 2 Press
Download Pdf Manuals
Related Search