Contents
1. Brackets 1 M2 5 screws 4 2 front mounting bracket 3 Tesla K10 GPGPU card 4 M3 screws 2 5 back mounting bracket 12 11 Connect the power cables to the GPGPU card Ensure the cables are properly attached 12 Connect the emergency throttling cable to the GPGPU card Figure 1 14 Connecting the Power and Emergency Throttling Cables 1 2 power cables 3 emergency throttling cable 13 Align and insert the GPGPU card assembly into the back GPGPU card riser connector until the card is fully seated 14 Secure the GPGPU card to the back of the sled cover using the four M3 screws working in a clockwise sequence Tighten the screws to 5 21 in Ib Figure 1 15 Installing the Back GPGPU Card Assembly 1 M3 screws 4 2 Tesla K10 GPGPU card assembly 3 back GPGPU card riser 15 Align the left air baffle with the screw holes on the back of the sled cover 16 Secure the left air baffle to the sled cover using the two M3 screws Tighten the screws to 5 21 in lb 17 Route the power and emergency throttling cables along the inside wall of the sled cover 18 Secure the cables to the retaining clips 19 Route the emergency throttling cable through the cable guide on top of the air baffle Figure 1 16 Installing the Left Air Baffle 1 left air baffle 2 M3 screws 2 3 power and emergency throttling cables 4 retaining clips 3 5 emergency throttling cable 20 Replace the top cover 21 Close the sled 22 Replace the2. Figure 1 9 Releasing the Power and Emergency Throttling Cables 1 power and emergency throttling cables 2 Remove the four M3 screws securing the air baffles 3 Lift the air baffles out of the sled cover and save for future use Figure 1 10 Removing the Air Baffles 1 M3 screws 4 2 right air baffle 3 left air baffle 4 GPGPU blank 4 Remove the four M3 screws securing the mounting brackets 5 Lift the mounting brackets away from the GPGPU blank Save the mounting brackets for future use 6 Lift the GPGPU blank out of the sled cover Save the GPGPU blank for future use Figure 1 11 Removing the Mounting Brackets and GPGPU Blank 1 M3 screws 4 2 front mounting bracket 3 back mounting bracket 4 GPGPU blank Z NOTE Ensure that the back GPGPU card riser is secured to the sled cover using the type B screw holes 7 Align the right air baffle with the screw holes on the back of the sled cover 8 Secure the right air baffle to the sled cover using the two M3 screws Tighten the screws to 5 21 in lb Figure 1 12 Installing the Right Air Baffle a 1 M3 screws 2 2 right air baffle 9 Align the front mounting bracket with the screw holes on the left of the GPGPU card and secure with two M2 5 screws Tighten the screws to 5 21 in Ib 10 Align the back mounting bracket with the screw holes on the right of the GPGPU card and secure with two M3 screws Tighten the screws to 5 21 in lb Figure 1 13 Installing the Mounting
3. 7 Installing the Back TeslaK10GPGPUcard 10 Cable Routing Diagram 2 15 Contents Contents Important Safety Information Observe the following safety precautions when installing NVIDIA Tesla K10 GPGPU cards in the PowerEdge C8220X sled AN WARNING Working on systems that are still connected to a power supply can be extremely dangerous A CAUTION The sled must be operated with the cover installed to ensure proper cooling A CAUTION To ensure proper airflow in the PowerEdge C8000 server enclosure if a sled module is removed it should be immediately replaced with another sled or sled blank A CAUTION Operating the system for extended periods of time without a sled blank installed can cause the PowerEdge C8000 server enclosure to overheat A CAUTION GPGPU cards can only be installed in the slots on the GPGPU card risers Do not attempt to install GPGPU cards directly into the riser connector on the system board K NOTE Itis recommended that you always use a static mat and static strap while working on components in the interior of the system To avoid injury to yourself or damage to your system follow these guidelines e Always disconnect the system from the power outlet whenever you are working inside the system e If possible wear a grounded wrist strap when you are working inside the system Alternatively discharge any static electricity by touching the bare metal chassis of the system cas
4. Brackets 2 A P r 1 M2 5 screws 4 2 front mounting bracket 3 Tesla K10 GPGPU card 4 M3 screws 2 5 back mounting bracket 10 Connect the power cables to the GPGPU card Ensure the cables are properly attached 11 Connect the emergency throttling cable to the GPGPU card See Figure 1 17 for the cable routing diagram Figure 1 6 Connecting the Power and Emergency Throttling Cables 1 2 power cables 3 emergency throttling cable 12 Align and insert the GPGPU card assembly into the front GPGPU card riser connector until the card is fully seated 13 Secure the GPGPU card to the front of the sled cover using the four M3 screws working in a clockwise sequence Tighten the screws to 5 21 in lbs Figure 1 7 Installing the Front GPGPU Card Assembly 1 M3 screws 4 2 Tesla K10 GPGPU card assembly 3 front GPGPU card riser 10 14 15 Align the left air baffle with the screw holes on the front of the sled cover Secure the left air baffle to the sled cover using the two M3 screws Tighten the screws to 5 21 in lbs 16 Route the emergency throttling cable through the cable guide on top of the air baffle Figure 1 8 Installing the Left Air Baffle 1 left air baffle 2 3 Tesla K10 GPGPU card assembly 4 M3 screws 2 emergency throttling cable Installing the Back Tesla K10 GPGPU card 1 Release the cables from the retaining clips and slightly lift the cables to access the screws on the sled cover
5. Dell PowerEdge C8220X Tesla K10 GPGPU Card Installation Guide Notes Cautions and Warnings KA NOTE A NOTE indicates important information that helps you make better use of your computer A CAUTION A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed AN WARNING A WARNING indicates a potential for property damage personal injury or death Information in this publication is subject to change without notice 2013 Dell Inc All rights reserved Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and PowerEdge are trademarks of Dell Inc Intel is a registered trademark of Intel Corporation in the U S and other countries NVIDIA and Tesla are trademarks and or registered trademarks of NVIDIA Corporation Other trademarks and trade names may be used in this publication to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Regulatory Model B06B Regulatory Type B06B001 2013 05 P NOOVKC Rev A00 Contents Important Safety Information 5 Recommended Tools 1 5 Information You May Need 6 Tesla K10 GPGPU Cards 6 Installing the Front TeslaK10GPGPUcard
6. e or the bare metal body of any other grounded appliance e Hold electronic circuit boards by the edges only Do not touch the components on the board unless it is necessary to do so Do not flex or stress the circuit board e Leave all components inside the static proof packaging until you are ready to use the component for the installation e Some cables have a connector with locking tabs if you are disconnecting this type of cable press in on the locking tabs before you disconnect the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before you connect a cable ensure that both connectors are correctly oriented and aligned Recommended Tools You may need the following items to install NVIDIA Tesla K10 GPGPU cards in the PowerEdge C8220X sled e 1 or 2 Phillips screwdriver e Static mat e Static strap Information You May Need For information about system features troubleshooting and component replacement see the PowerEdge C8220X Hardware Owner s Manual This document is available at dell com support manuals Tesla K10 GPGPU Cards 1 Remove the sled from the PowerEdge C8000 server enclosure For detailed information on removing the sled see the PowerEdge C8220X Hardware Owner s Manual 2 Place the sled on a flat stable surface 3 Open the sled For detailed information on opening the sled see the PowerEdge C8220X Hardware Owner s Manual Remo
7. sled in the server enclosure 14 Cable Routing Diagram KA NOTE Route the cables properly inside the sled to prevent the cables from being pinched or crimped Cable Routing for Front and Back Tesla K10 GPGPU Card Assembly Figure 1 17 n 0 om OS I I I I O Oo DO 1 2 3 4 L 05 di gt 2 6 me 7 8 y i 9 7 1615 14 igi 16 power connector on front GPGPU card riser twin axial cable on back GPGPU card riser power emergency throttling connector on node power distribution board NPDB power connector on NPDB power connector on NPDB power connector on NPDB power connector on back Tesla K10 GPGPU card power connector on front Tesla K10 GPGPU card power emergency throttling connector on front Tesla K10 GPGPU card 12 14 16 power connector on back GPGPU card riser twin axial cable connector on system board power emergency throttling connector on NPDB power connector on NPDB power connector on NPDB power connector on back Tesla K10 GPGPU card power emergency throttling connector on back Tesla K10 GPGPU card power connector on front Tesla K10 GPGPU card
8. ve the five M3 screws securing the top cover Lift the top cover away from the sled cover Figure 1 1 Removing the Top Cover 1 top cover 2 M3 screws 5 Installing the Front Tesla K10 GPGPU card 1 2 Lifttheair baffles out of the sled cover and save for future use Remove the four M3 screws securing the air baffles Figure 1 2 Removing the Air Baffles 1 M3 screws 4 2 right air baffle 3 left air baffle 4 GPGPU blank 3 Remove the four M3 screws securing the mounting brackets 4 Lift the mounting brackets away from the GPGPU blank Save the mounting brackets for future use 5 Lift the GPGPU blank out of the sled cover Save the GPGPU blank for future use Figure 1 3 Removing the Mounting Brackets and GPGPU Blank LZ 1 M3 screws 4 2 front mounting bracket 3 back mounting bracket 4 GPGPU blank 6 Align the right air baffle with the screw holes on the front of the sled cover 7 Secure the right air baffle to the sled cover using the two M3 screws Tighten the screws to 5 21 in lbs Figure 1 4 Installing the Right Air Baffle 1 M3 screws 2 2 right air baffle 8 Align the front mounting bracket with the screw holes on the left of the GPGPU card and secure with two M2 5 screws Tighten the screws to 5 21 in lbs 9 Align the back mounting bracket with the screw holes on the right of the GPGPU card and secure with two M3 screws Tighten the screws to 5 21 in lbs Figure 1 5 Installing the Mounting
Download Pdf Manuals
Related Search