Definitive Technology Speaker Reference Series In-Ceiling Speaker User's Manual
Contents
1. Frequency Response 30 Hz 30 kHz Nominal Impedance Compatible with 4 8 ohm outputs Driver Complement Two 41 2 bass mid drivers Two 5 4 x 4 s pressure driven low bass radiators One 1 Pure Aluminum dome tweeter Sensitivity 92 dB Specifications subject to change without notice Visit us at www definitivetech com Limited Warranty 5 Years for Drivers and Cabinets 3 Years for Electronic Components Definitive Technology warrants to the original retail purchaser only that this Definitive Technology Loudspeaker Product the Product will be free from defects in materials and workmanship for a period of five 5 years covering the drivers and cabinets and three 3 years for the electronic components from the date of the original purchase from a Definitive Technology Authorized Dealer However this warranty will automatically terminate prior to the expiration of five 5 years for the drivers and cabinets and three 3 years for the electronic components if the original retail purchaser sells or otherwise transfers the Product to any other party The original retail purchaser shall hereinafter be referred to as you Defective Products must be shipped together with proof of date of purchase prepaid insured to the Authorized Dealer from whom you purchased the Product or to the nearest factory service center Product s must be shipped in the original shipping container or its equivalent in any case2. If ceiling joists are wider than 12 apart you will need to shim or frame in the enclosure with appropriate framing material Before starting construction or modification of your ceiling you should familiarize yourself with any applicable local fire and building codes Make sure the locations you select do not conceal studs electrical wiring or plumbing Prior to installation hold the speaker in your chosen location to make sure it meets the clearance requirements around obstacles such as studs corners beams lighting fixtures and door window frames Installation Procedure Overview continued The speaker enclosure needs to be against joists or framing material on the 2 parallel sides that are to be fastened with the screws The clearance required on outside ceiling surface is 1 around the cutout to clear the speaker bezel On inside surface 1 s of clearance is required to clear lock arms on the sides that will not be fastened to the joists or framing material Also note that the installation of the RCS III may require some modifica tion of the joist structure in your ceiling This should only be done by a competent professional who will configure the studs to maintain their structural integrity and make sure that everything is in compliance with all local and state building code requirements Speaker wire must be run inside your ceiling as part of the installation process of in wall loudspeakers Plan the connection before
3. Definitive Technology The Leader in High Performance Loudspeakers UIW RCS M Reference Series In Ceiling Speaker Owner s Manual Congratulations Congratulations on your purchase of the Definitive Technology UIW RCS III Loudspeaker This reference quality loudspeaker provides the highest level of sonic performance and construction quality and is designed for easy flush mount installation in ceilings of homes and commercial spaces Six years of intensive research and development by Definitive engineers working in collaboration with one of the world s leading industrial design firms has produced the finest architectural loudspeakers on the market The beautiful upscale designer styling of this model is perfect for the finest homes belonging to the most discriminating homeowners The UIW RCS III Loudspeaker The RCS III Incorporates high power high definition cast basket Definitive bass midrange drivers combined with pressure coupled low frequency radiators and state of the art Definitive 1 dome tweeters Incorporates polypropylene cones with butyl rubber surrounds Incorporates a complete precision crossover system designed by Definitive engineers for seamless driver blending Incorporates a completely sealed non resonant medite enclosure to assure you of laboratory reference quality performance in your home Is moisture resistant to allow use in bathrooms etc Is easily paintable and comes co
4. TERIAL g Cc 3 10 1 2 10 38 CAVITY SIZE REQUIRED BETWEEN INSTALLED TEMPLATE CUT OUT FRAMING MATERIAL 10 3 8 TEMPLATE CUT OUT LOCK ARM 4 PLACES WOODSCREW 2 PLACES Diagram 2 REAR VIEW FROM INSIDE CEILING INSTALLATION IN CEILING WITH JOISTS 12 ON CENTER WITH OBSTRUCTING CROSSBEAM e UNIT MUST BE AGAINST THE CROSSBEAM AND 2 JOISTS MINIMUM CAVITY REQUIRED 10 1 2 BETWEEN JOISTS THAT WOOD SCREWS ARE TO BE SECURED TO 12 3 4 BETWEEN JOISTS OR OBSTRUCTIONS ON SIDES LOCK ARMS ARE TO U e DEPTH 5 7 8 WOODSCREW 3 PLACES LOCK ARM 2 PLACES Troubleshooting Your UIW RCS III Speakers 10 1 2 MINIMUM CAVITY SIZE BETWEEN STUDS HOLDING WOODSCREWS EXISTING CROSSBEAM wh CAUSING OBSTRUCTION EXISTING CEILING JOISTS 12 ON CENTER 10 3 8 TEMPLATE CUT OUT 10 3 8 TEMPLATE CUT OUT 11 3 8 MINIMUM CAVITY SIZE REQUIRED BETWEEN CROSSBRACES TO CLEAR LOCK ARMS UNIT MUST BE PLACED AGAINST CROSSBEAM 11 4 MINIMUM CLEARANCE REQUIRED FOR LOCKARMS Diagram 3 If you experience any difficulties with your UIW RCS III Loudspeakers try the suggestions described below If you are still having problems please consult your Definitive Technology authorized dealer for assistance Make sure all your system interconnections and powe
5. any incidental or consequential damages arising out of the use or inability to use the Product even if Definitive Technology or a Definitive Technology Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation may not apply to you All implied warranties on the Product are limited to the duration of this expressed Warranty Some states do not allow limitation on how long an implied Warranty lasts so the above limitations may not apply to you This Warranty gives you specific legal rights and you also may have other rights which vary from state to state This product complies with the essential requirements of EMC directives 89 336 EEC and 73 23 EEC inclusive of 93 68 EEC and carries the CE mark accordingly EOAT012909
6. appropriate colored out put terminal on the unit again making red to red and black to black connections This will ensure absolute phase throughout the system Securing speaker e Installation of this product must follow all local and state building code requirements e We strongly recommend using a qualified professional installer who is knowledgeable of local building codes e We recommend holding the unit by the bezel and outer edges of the speaker to avoid damaging the drivers e Place speaker in hole and secure to joists or framing material with at least 2 of the screws provided Tighten screw on one side before installing and tightening the opposing side Step by Step Installation continued e As a minimum the speaker must be secured using two screws provided on 2 parallel sides See Diagrams and 2 page 9 for reference e If speaker is mounted against a crossbeam install one additional 8 x 3 2 wood screw included into side that is against crossbeam to secure speaker and prevent rattling See Diagram 3 page 10 for reference e Secure lock arms on sides that are not secured using wood screws See Diagrams 1 2 and 3 page 9 and 10 for reference e The metal pivoting lock arms are pre installed in the loudspeaker frame with Phillips screws The lock arms can be rotated left or right by turning the screws e Fit grille on speaker bezel VERY IMPORTANT Please note that the pivoting lock
7. arms are not designed to support the weight of the speaker They are only designed to pull the speaker tight to the ceiling and prevent it from rattling Do not use them for supporting the speaker The screws going through the speaker and into the joists are there for support and must be properly used EXISTING CEILING JOISTS 10 1 2 MINIMUM CAVITY 12 ON CENTER SIZE BETWEEN 70 8 5 1 1 4 MINIMUM CLEARANCE REQUIRED TO CLEAR LOCKARMS BEAM TO SHOW MINIMUM DISTANCE REQUIRED TO CLEAR OBSTRUCTION REAR VIEW FROM INSIDE CEILING INSTALLATION IN CEILING WITH JOISTS 12 ON CENTER MINIMUM CAVITY REQUIRED 10 1 2 BETWEEN JOISTS THAT WOOD SCREWS TEMPLATE MINIMUM CAVITY ARE TO BE SECURED TO CUT OUT SIZE REQUIRED TO 12 3 4 BETWEEN JOISTS OR OBSTRUCTIONS CLEAR LOCK ARMS ON SIDES LOCK ARMS ARE TO USED 0 3 8 TEMPLATE CUT OUT DEPTH 5 7 8 WOODSCREW 2 PLACES LOCK ARM 4 PLACES Diagram 1 REAR VIEW FROM INSIDE CEILING INSTALLATION IN CEILING WITH JOISTS 24 ON CENTER EXISTING CEILING JOISTS MINIMUM CAVITY REQUIRED 24 ON CENTER 10 1 2 BETWEEN INSTALLED MATERIAL THAT WOOD SCREWS ARE TO BE SECURED TO 12 3 4 BETWEEN JOISTS OR OBSTRUCTIONS ON SIDES LOCK ARMS ARE TO USED e DEPTH 5 7 8 NOTE UNIT DOES NOT NEED TO BE CENTERED BETWEEN JOISTS ALLOW FOR 1 1 4 OF CLEARANCE ADDED FRAMING ON EACH SIDE OF CLEAR LOCK ARMS MA
8. er where crossbeam is closer than 1 from side of enclosure Enclosure MUST be against the crossbeam and 2 joists boxing it in on 3 sides Shim as required This will require 1 additional 8 x 3 wood screw and side gasket material not included to secure to crossbeam and prevent rattling Place template against crossbeam and mounting joist Trace around template with pencil Cut hole 6 See Diagram 3 page 10 for reference Gasket requirements and application There are 2 sizes of gasket strips included in the accessory pack with the owner s manual 5 long gaskets 1 short gasket The gaskets are to be applied as follows 2 long gaskets on back of enclosure 2 gaskets on each side of enclosure to be placed against joist or framing material The short gasket is provided to run on the side of the enclosure where the terminal cut away is located Connecting the speaker e Run color coded wires between the speaker cavity and amplifier unit When running the wires inside the ceiling to the opening leave a minimum of 18 of additional length in the cavity to facilitate speaker connection e Fish wiring out of hole e Connect the speaker wires to the UIW RCS III taking care to make red to red and black to black terminal connections e Refer to your amplifier or receiver loudspeaker wiring instructions turn off the unit and connect the speaker wires to the
9. lle and frame must be painted separately and for best results prior to installation For the grille spray painting is the recommended method Follow the paint manufacturer s directions for ventilation and correct spraying procedure Be very careful not to clog the speaker grille with too heavy a coat of paint as this will impair system sonic performance For the frame spray painting is preferred but brush or roller will also give good results The supplied frame masks should be put in place to protect the speaker components for whichever method you choose Installation Procedure Overview The RCS II is designed to be installed inside the ceiling of your home quickly and easily Because of its superb sonic performance installation loca tion within your room is very flexible Your room is not like anyone else s room and because of its unique size and shape will have its own require ments for optimal sonic performance We recommend that you consult with the Custom Installation Specialist at your Definitive Technology dealer regarding your special needs or if you are at all uncertain about the best and safest way to install your RCS III Installation of this product must follow all local and state building code requirements We strongly recommend using a qualified professional installer who is knowledgeable of local building codes The UIW RCS III is designed for mounting inline or at 90 degrees to 12 on center ceiling joists
10. mplete with mounting templates and plastic paint masks Can be used as an exceptional left main right main center channel or rear side surround in a state of the art home theater system or as stereo pairs in a 2 channel music system The Sound Quality Is Extraordinary The UIW RCS IIIs have been voiced by Definitive engineers using the superb facilities of the Definitive Technology Advanced Research Facility to the same high end standards as all Definitive loudspeakers The drivers and baffles are perfectly integrated into the design to minimize the diffraction problems that are inherent with most other in wall loudspeakers To ensure that you experience the finest performance possible from your UIW RCS IIIs we encourage you to read this owner s manual to familiarize yourself with the proper installation and set up procedures Unpacking Your UIW RCS III Loudspeakers Please Inspect For Shipping Damage Each loudspeaker leaves our plant in perfect condition Any visible or concealed damage most likely will have occurred in handling after it left the plant and should be reported at once to your Definitive dealer or the delivery company that delivered your loudspeakers Please unpack your system carefully Save all cartons and packing materials in case you move or need to ship your system Record the serial numbers found on the back of the UIW RCS III Loudspeakers in the appropriate place on your warranty card UIW RCS III Applicatio
11. ns The UIW RCS III is designed to be mounted in ceilings and used as a front main left right or center channel loudspeaker in a stealth home theater system of the highest quality In addition they can be used as rear or side surround speakers or as left and right stereo speakers UIW RCS III Positioning Definitive s UIW RCS III Loudspeakers are designed to be mounted in ceil ings with excellent results Because of their wide dispersion characteristics and other aspects of their superb sonic performance mounting position in your room is very flexible Due to the different requirements of the wide variety of room shapes and sizes we recommend that you consult with the custom installation specialist at your Definitive Technology dealer regarding your own particular needs Your Complete Definitive Home Theater For best results we recommend that you use Definitive speakers in combination with your RCS IIIs for the best overall sonic performance A popular choice for matching side or rear surround speakers is the Definitive UIW RSS III In wall or free standing subwoofers may be used with the RCS III Popular choices are the in wall Definitive UIW Sub 10 10 UIW Sub Reference or our freestanding SuperCube subs Painting Your UIW RCS III Loudspeakers The UIW RCS III Loudspeakers are easily paintable and are shipped with plastic paint masks which should be retained even if you initially decide not to paint the speakers The gri
12. r cords are solidly in their place Check to be sure that the power cords and or speaker wires have not been damaged Many amplifier receivers have sophisticated internal protection circuitry If for some reason the protection circuitry is tripped please turn down the system s volume and wait five minutes before trying the system again Technical Assistance It is our pleasure to offer assistance if you have any further questions or comments Please feel free to contact our technical support staff at Definitive Technology LLP 11433 Cronridge Dr Suite K Owings Mills MD 21117 or call 410 363 7148 Service and warranty work on your Definitive loudspeakers will normally be performed by your local Definitive Technology dealer However if you wish to return the speaker to us please contact us first describing the problem and requesting authorization as well as the location of the nearest factory service center Please note that the address given in this booklet is the address of our offices only Under no circumstances should loudspeakers be shipped to our offices or returned without contacting us first and obtaining return authorization Definitive Technology Offices 11433 Cronridge Dr Suite K Owings Mills Maryland 21117 Phone 410 363 7148 UIW RCS III Specifications UIW RCS Ill Outer Dimension 1112 W x 1112 H Cut out Size 10 8 W x 103 8 H x 57 D Recommended Amplification 10 300 Watts channel
13. the risk of loss or damage in transit is to be borne by you If upon examination at the Factory or a Definitive Technology Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this Warranty period Definitive Technology or the Definitive Technology Authorized Dealer will at its option repair or replace this Product at no additional charge except as set forth below All replaced parts and Product s become the property of Definitive Technology Product s replaced or repaired under this Warranty will be returned to you within a reasonable time freight collect This Warranty does not include service or parts to repair damage caused by accident mis use abuse negligence inadequate packing or shipping procedures commercial use voltage in excess of the rated maximum of the unit cosmetic appearance of cabinetry not directly attributable to defects in materials or workmanship or service or repair or modification of the Product which has not been authorized by Definitive Technology Definitive Technology makes no Warranty with respect to its Products purchased from dealers or outlets other than Definitive Technology Authorized Dealers This Warranty is in lieu of all other expressed Warranties If this Product is defective in material or workmanship as warranted above your sole remedy shall be repair or replacement as provided above In no event will Definitive Technology be liable to you for
14. you start your loudspeaker installation Step by Step Installation Mounting options overview Installation of this product must follow all local and state building codes We strongly recommend using a qualified professional installer who is knowledgeable of local building codes Required cutout and cavity size e Template cutout size 10 s W x 10 s L Minimum size of installation cavity inside ceiling and between joists is as follows Depth 57 s 10 between joists on the sides the wood screws are to be installed in 12 4 between joists on sides the lock arms are to be used 1 s of space required on each side to clear lock arms See Diagram 1 page 9 for reference Step by Step Installation continued Hole location options and requirements Mounting in ceiling with joists 12 on center Place template against inside edge of joist Trace around template with pencil Cut hole See Diagram 1 page 9 for reference Mounting in ceiling with joists wider than 12 on center Place template at least 1 away from existing joists to clear lock arms Template does not need to be centered between joists Trace around template with pencil Cut hole Install framing material inside cavity running 90 degrees to existing joists leaving 10 2 between frame sides See Diagram 2 page 9 for reference e Mounting in ceiling with joists 12 on cent
Download Pdf Manuals
Related Search