DCS CMOTTK30 User's Manual
Contents
1. MODEL CMOTTK30 CONVECTION MICROWAVE TRIM KIT INSTALLATION INSTRUCTIONS Before you begin read these instructions completely and carefully Getting Started m Remove packaging Contents Tools Required Part Description Qty 1 8 Drill Trim Assembly 1 2 Phillip Screwdriver Base 1 Rear Duct 1 Forward Duct 1 Foam Tape 2ft Mounting Bracket L R 2 Sheet Metal Screws 14 Before installing trim kit install the convection duct as follows 1 Insert the rear section of the duct into the forward section of the duct and install 4 screws supplied Fig 01 2 Install foam tape on 2 flanges of the rear section of the duct Fig 02 3 Remove and retain the 2 top screws left and right located at the rear vertical edges of the Microwave Fig 03 4 Place the duct on top of the Microwave and reinsert the 2 screws removed in Step 3 Fig 04 Installing Trim Kit 1 Cut opening in the cabinet face per the following dimensions Height 19 3 16 1 16 0 Width 25 3 4 1 16 0 Note Refer to diagram on the following page The minimum cabinet depth is 20 When installing the Microwave and Trim Kit in combination with a Wall Oven or Warming Drawer please follow the recommendations in the Microwave Installation Use amp Care Manual 2 Add adequate platform base support in the bottom of the cabinet for trim kit base to rest on Fig 05 3 Marka centerline on2. RIM SCREW HOLE N FOAM TAPE ON CENTER LINE MOUNTING BRACKET SS SUPPORT INSERT 4 TRIM KIT ASSEMBLY BASE INSERT 1 CABINET CUT OUT 19 13 16 1 16 0 T i INSERT 2 TRIANGULAR O CENTERING L TOP SCREW HORIZONTAL SCREW HOLE CLIP ORIENTATION LOCATE MOUNTING BRACKET ON BASE IN BOTTOM CORNERS OF CUTOUT INSERT 3 Stainless Steel Care This Trim Kit is made of stainless steel Use the mildest cleaning procedure first Start with hot soapy water rinse and dry If the trim kit has food soil remaining try a general kitchen cleaner such as Fantastik Simple Green or Formula 409 Apply cleaner with a damp sponge rinse thoroughly and dry Always scrub lightly in the direction of the grain Do not use a steel wool pad it will scratch the surface To touch up noticeable scratches in the stainless steel sand very lightly with dry 100 grit emery paper rubbing in the direction of the grain After cleaning use a stainless steel polish such as Stainless Steel Magic DCS by Fisher amp Paykel 5800 Skylab Road Huntington Beach CA 92647 Tel 714 372 7000 Fax 714 372 7001 iit sad bi Fisher amp Paykel Aoii i Customer Service 888 281 5698 ae www dcsappliances com P N 241185 Rev A 10 07
3. the front edge of the cabinet bottom Fig 05 4 Place trim kit base and align centerline mark to the triangular notch on the front edge of the base Fig 06 5 Drill 1 8 pilot holes in the cabinet using the base as a template and install a screw through the base into the cabinet to prevent the base from shifting Fig 07 6 Insert Microwave into opening on top of the base The Microwave feet should sit in the recesses on the base for correct alignment The Microwave should be plugged in at this point Fig 7 Place the right and left mounting bracket supports by resting the bottom edges of the supports on the bottom of the cutout Fig 08 The long flange on the side supports should clear the side of the cutout by approximately 1 16 see Fig 09 Install top screws into the cabinet face by first drilling 1 8 pilot holes see inserts 3 and 4 8 Install trim kit face by inserting top pins of trim into corresponding sockets on the top corners of clip support plates see insert 1 9 Finish the assembly by inserting the bottom pins into the corresponding sockets on front edge of the base see insert 3 Check for proper door opening clearances Bracket Support on the bottom of cutout REAR CABINET CONVECTION DUCT eee HORIZONTAL CLIP Mere ORIENTATION FORWARD hae ON MOUNTING CONVECTION 25 3 4 4 46 0 BRACKET DUCT FONETAPEON aS 1 8 HOLE FOR THIS FLANGE MOUNTING TOPPIN N SURE OF T
Download Pdf Manuals
Related Search