Dakota Digital LAT-NR100 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS Id j LAT NR100 D a ki ota D d ta LED Tail Lights for 1967 68 SS and 1970 73 Camaro MAN 650153 Kit Includes Installation 1 Remove the tail light assembly from the vehicle by removing the original bulb sockets from the housing Then remove the housing hardware so it can be removed from the car Remove the housings from the vehicle carefully so the housing to body gaskets are not damaged 2 Next remove the lens The 67 68 Camaro has six screws that hold the housing halves together which will need to be removed to gain access to lens The 70 73 Camaro lens has tabs locking it into the plastic housing Pry the tabs gently with a screwdriver to remove lens i i LES a y z wre T ee a E MAN 650153 3 Now is a good time to clean the lens and housing If lenses are in bad shape a new set is recommended lf you are installing this kit into a 67 68 Camaro skip ahead to step 5 For the 70 73 Camaro some of the hardware will need to be changed out for proper mounting bracket 4 Changing the installed 67 68 mount bracket to the 70 73 mounting bracket a Note how the current assembly is attached and notice how the wires are routed for re assembly ENSURE THE WIRES ARE NOT PINCHED IN THE NEW ASSEMBLY b Remove the screw at the back of the LED assembly it is a 5 8 6 32 machine screw This will remove the mounting bracket that will need to b2. problem your full name and address street address preferred and a telephone number where you can be reached during the day An authorization number for products being returned for repair is needed We will contact you if any repair charges exist Any returns for warranty work must include a copy of the dated invoice or bill of sale LED LIGHTING LIMITED LIFETIME WARRANTY DAKOTA DIGITAL the Company warrants to the ORIGINAL PURCHASER of this LED Lighting product under normal use and condition be proven defective in material or workmanship DURING THE LIFETIME OF THE CAR IN WHICH IT WAS ORIGINALLY INSTALLED such defect s will be repaired or replaced at the Company s option without charge for parts or labor directly related to repairs of the defect s To obtain repair or replacement within the terms of this Warranty the product is to be delivered with proof of warranty coverage e g dated bill of sale specification of defects transportation prepaid to the factory This Warranty is valid for the original purchaser only and may not be transferred This warranty does not cover damage to vehicle electrical system This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or accident This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTA
3. BLITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESSED OR IMPLIED WHATSOEVER No person or representative is authorized to assume for the Company any liability other that expressed herein in connection with the sale of this product FOR SERVICE SEND TO DAKOTA DIGITAL 4510 W 61st ST N SIOUX FALLS SD 57107 USA 800 852 3228 Email us at techsupport dakotadigital com MAN 650153
4. e changed c Locate the supplied longer mount bracket and reattach using the shorter supplied 1 2 6 32 machine screw The shorter screw must be used since the taller mount is thinner Tighten the screw down in the center of the slot The LED assembly can be moved up or down to adjust the height of the light d Note NOT FOLLOWING THESE STEPS CAN DAMAGE THE CIRCUIT BOARD 1967 1968 Camaro mount 1970 1973 Camaro mount 1970 1973 Camaro LED Assembly 5 Remove the mounting plate from the bottom of the assembly which is attached with two 3 8 6 32 machine screws es 7 MAN 650153 7 Feed the wires through the larger hole in the mounting plate Guide the mounting plate to the bottom of the housing The flat side of the mounting plate should be down and the side with the slight raised center should go up into the housing This will align the mount in the original housing 8 Now hold the LED assembly so that it is centered over the hole where the original bulb was located and align the mounting plate from the bottom with the slot in the housing The screw holes should be lined up e i Raab i Ta dij F pi rics i ie i trais i t n erty a i Hig 7 gn KJ Ti x S 1 ah ls v o RRN N ee oath Le ee hae 8 P aL 4 F bit J 5 gt m i gt ae i a TA TA a i ta ai ta 7 i 9 Screw the mounting plate into the assembly mount using the two previously remo
5. p down flush with the edge of the clear body completing the connection The connection will only be correct if pressed firmly down with pliers J J ZN Attach to metal bolt or screw NG Ne ee for Ground connection with metal housings OR GREEN wire BROWN wire BLACK wire from LED from LED from LED assembly assembly assembly BLACK wire Turn Signal wire Tail Light wire Ground wire from vehicle from LED from vehicle from vehicle harness assembly harness harness with plastic housings Brown Brown Ground Black Chassis or body 13 Repeat for the other side 14 Test the tail lights brake lights and turn signals If the turn signals do not flash you will need to upgrade your flasher If you are replacing only the rear turn signals you should be able to use a heavy duty electronic flasher from your local parts store If you are replacing both front and rear or do not have front bulbs you will need a no load flasher Dakota Digital part number LAT NLF SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our units Should you ever need to send the unit back for repairs please package the product in a good quality box along with plenty of packing material Ship the product by UPS or insured Parcel Post Be sure to include a complete description of the
6. ved 3 8 6 32 screws in 5 a i ats Ji Y 4 D j b k a J by lt o Liat ar ST ORAN y A k kA j a i ET AA 4 l j i al s j A i t a A 1A k 1 lt i i j a i 4 hh oe P aT 6 ale a i is 3 p S i i Maa a a E e 10 Install the lens and or re assemble the tail light housing insuring all gaskets are intact and in place Install the tail light housing back into the vehicle You are now ready to wire the LED assembly into the vehicle tail light harness MAN 650153 11 Start by cutting off the existing light socket as it will not be used Do not strip wires Trim the wires from LED assembly to appropriate length once mounted making sure wires are routed cleanly and securely 12 Use the supplied moisture resistant pigtail connectors to attach the wires from the new LED assembly to the existing vehicle harness Insert appropriate wire from vehicle harness and mating LED assembly wire into a connector and crimp following instructions below For the best connection soldering is recommended But to simplify installation the supplied connectors will provide a fast weather resistant connection The correct crimp method for the supplied connectors is 1 Insert UNSTRIPPED wires from both LED assembly and vehicle harness into the connector and ensure they are all they way in by observing the clear bottom of the connector to see the wires are touching the end 2 Use pliers to push the blue ca
Download Pdf Manuals
Related Search