Daewoo Electronics DSC-3270E User's Manual
Contents
1. 21 Sound Equalizer Pro Logic Balance Center Surround Dolby Noise Dolby Noise Automatic clock setting and correction Even though you turn the TV off with MAIN POWER ON OFF button if you select a programme of your country which has Teletext or PDC transmission clock will be set and corrected automatically This function is only available for the countries as follows Deutschland Great Britain France Italy Sweden Switzerland Netherlands Ireland SETTING THE WAKE UP TIME PROGRAMME Confirm the Clock is set Wake up time is only available when Clock is set Select the Wake up to YES The Wake up time and Wake up prog will be displayed Set Wake up time and prog in a same way to the above for Clock The set will switch on to this time and programme number Note that the Wake up time will not operate in Childlock mode SLEEP By pressing the SLEEP button repeatedly you can select one of the following settings 00 20 gt 00 40 gt 01 00 gt 01 20 gt 01 40 gt 02 00 The set will turn off after the time you select Automatic Switch Off when No Broadcast Signal If a broadcast signal is not present for about 30 minutes the set will be auto matically turned off In AV mode however this function does not operate CHILD LOCK You can prevent the use of the TV set without the remote control The set is ch2. if the button is pressed once more Volume 21 SOUND CONTROL Press the MENU button Place the selection bar to the Sound with UP DOWN button Press the RIGHT button to call up Sound menu Select the required function by moving the selection bar ith the UP DOWN buttons Press the RIGHT button to call up the each sub menus Equalizer There are four possible choice considering your preference Favourite Music Speech Flat In Favourite mode you can adjust a level at each frequency band with LEFT RIGHT button Dolby Prologic There are four possible choice considering your preference Normal Wide 3 Stereo Dolby Noise Smart Sound Selection When you press the sound effect button gt repeatedly you can call up easily one of the following Dolby suround Available only for Dolby surround Mode Favourite Music Speech Flat Normal Wide 3 Stereo Off Favourite Balance Balance the loudness of the left and right speaker Center amp Surround Adjust the Center speaker amp Surround speaker Volume with the VOLUME buttons Dolby Noise Test a each speaker s sound output Lest Center Right Surround 3 Left SOUND MODE There may be cases of stereo broadcasts where excessive noise will be heard due to weak incoming signal You may be able to eliminate this noise by selecting the MONO mode Press the Sound Mode C CD I IL but
3. receiver a Camcoder and a computer RGB In most cases the set changes automatically to AV1 or AV2 mode when the VCR connected is in playback mode If not press the TV AV button ce on the remote controller or on the front of the set Whenever the AV button is pressed the on screen display will change as shown AV1 gt AV2 gt AV3 gt AV3 S gt gt TV The AV1 will be displayed on the screen with the current programme number In AV mode you can change the TV programme number with the UP DOWN button or the NUMBER button 0 9 The SCART 3 is used to connect a VCR a satellite receiver a s video camcoder or a peri TV decoder Select AV3 mode by pressing the TV AV button ce When you use s video camcoder select AV3 S mode by pressing the TV AV button ce SIDE AV JACK AV4 The AV JACK is used to connect a VCR a camcoder or S Video cam coder Select AV4 mode by pressing the TV AV button ce Press this button again to return to the TV mode Vertical Synchronization by means of 100 Hz Scan might be unstable in REW and CUE Function with only 2 Head VCR HEADPHONE JACK Insert the headphone plug 3 5 mm 9 into the headphone socket The sound from the speaker will be cut off You can control the heaphone sound with the LEFT RIGHT button You can hear the Dual I Dual II sound from Headphone during the loud speaker are output the Dual II Dual I sound respectively External Surroun
4. to adjust the fine tuning Move the selection bar to Fine tune and press the RIGHT LEFT button to activate fine tuning up or down Note that it operates while the RIGHT LEFT button is being pressed The change is memorized automatically Adjust Tilt function ADJUST TILT FUNCTION Press PR buttons to select Tilt Press the RIGHT or LEFT buttons to level a tilted picture Note The effect of the earth s magnetic field can vary with location As a result the picture may project on a slight tilt or out of square alignment with the face of the picture tube Install Auto Setup Manual Tune Fine Tune Edit Tilt PAL Position Adjust Return Picture Install Auto Setup Manual Tune Fine Tune Edit Tilt PAL Manual Tune 00 Prot Edit Pr Ch Picture Sound Skip 01 FRI C02 PAL 02 C07 France No 0 Cii SECAM DK No 04 C25 PAL 05 C85 PAL No o6 C50 SECAM DK Yes 07 C50 SECAM DK Yes Adjust EN Skip Cursor Move Retum um Delete Install Auto Setup Manual Tune Fine Tune Edit Tilt Fine Tune 493 75MHz Install Auto Setup Manual Tune Fine Tune Edit Tilt Position Adjust eturn DAILY USE RECALL The RECALL button is u
5. DAEWOO Colour Television Instruction Manual MODEL NO DSC 3270E Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories 1 nt 5n v M 7 7 IDENTITY OF FEATURES ON LOCAL AND REMOTE CONTROL DSC 3270E TV SET mW FRONT PROGRAM VOLUME TVIAV TIMER STAND BY REMOTE MAIN DOWN UP DOWN UP MENU INDICATOR INDICATOR SENSOR POWER BUTTON BUTTON BUTTON SIDE 1 tfr 5e gt lt VIDEO AUDIO S VHS HEAD INPUT INPUT INPUT PHONE IDENTITY OF FEATURES ON LOCAL AND REMOTE CONTROL REAR EXTERNAL SURROUND SPEAKER TERMINAL SCART SOCKET 1 2 3 AERIAL TERMINAL REMOTE CONTROL TXT TXT VOLUME terrass rs VOLUME PAGE UP DOWN DOWN CURSOR UP CURSOR LEFT VOLUME UP VOLUME UP CURSOR RIGHT MENU eire nentes MENU PRDOWN PAGE DOWN POWER POWER CURSOR DOWN NORMAL NOT USE Nee NOTUSE 0 9 0 9 TXT Sere Ne TII TV SLEEP San teet NOT USED SOUND MODE NOT USED NOT USED nnn HOLD ES MUTE NOT USED se CANCEL NORUSED INDE iE r
6. M DIC No Sound informatin B G UL 1 D K 05 C35 PAL I No Skip information YES NO E os NB Terrestrial transmissions in GREAT BRITAIN are PAL I LE picture information is PAL Moe Em Move sound informatin I DELETING THE PROGRAMME POSITIONS Position the selection bar to programme number to delete with the UP DOWN buttons Note that you can move the selection bar when the cursor is on the Pr pro gramme no Edit Press the DELETE Yellow button Pr Ch Picture Sound 5 01 FRi C02 PAL B G No 08 C07 Frane UL No MOVING THE PROGRAMME POSITIONS Position the selection bar to programme number you want to move mee Pressthe MOVE Green button The colour of selection bar will be changed D imm COS SEGAM DIK Yes in Purple from Blue Postion moo Position the new blue selection bar to new programme number Retum Delete Press the MOVE Green button SKIPPING THE CHANNELS Select SKIP YES or NO with the SKIP Red button You can also use the UP DOWN button after moving the cursor to Skip The programme marked with SKIP YES is skipped when changing chan nel using the UP DOWN button A skipped programme number can be selected using the NUMBER button 0 9 will be displayed in Cyan Picture Sound Skip ENTER A STATION NAME Move the cursor to Name Then a letter from the Alphabet Number and symbols will appear ABCDEFGHIJKLM
7. NOPQRST You can enter a station name with the UP DOWN and LEFT RIGHT but UVWXYZ 0923486789 tons Adjust mm Skip Cursor mm Move Return mm Delete D MANUAL CHANNEL SETTING Press the NUMBER buttons 0 9 or the UP DOWN button to select a pro gramme number you want Locate the selection bar on the Manual tune at the Install menu Select the system with Picture Cyan button Select the SECAM F fora French stations and PAL or SECAM for the others Press the RIGHT or LEFT button Atuning screen will appear and a cursor will move from left to right from right to left If you want to stop tuning press the MENU button After searching a station the tuning screen will disappear and then the chan nel will be memorized automatically SEARCHING A CHANNELS IN THE EDIT MENU You can also search a channel at the Edit menu Position a selection bar to Pr number you want Position the cursor to the Picture with LEFT RIGHT button Select the system PAL or SECAM SECAM F of channel you want to search with the UP DOWN button Position the cursor to C or S entry position with LEFT button For spe cial channels select the S with UP DOWN button Position the cursor to channel number entry position with RIGHT button Search a channel with UP DOWN button FINE TUNING If you are unable to get a good picture or sound because of a poor broad casting signal it is possible
8. OWN buttons increase or decrease the current page number by 1 INDEX PAGE You can switch directly to the programme preview with TOP text or the overview page of the station you are currently viewing by pressing the INDEX 21 but ton PAGE HOLD Several sub pages can be combined under a page number and are scrolled at an interval determined by the television station The presence of sub pages is indicated by for example 3 6 beneath the time which means that you are looking at the 3rd page of a total of 6 pages w want to look at a subpage for a longer period of time press the HOLD button The stop appears beside page number and the contents of the subpage shown are kept on the screen and no longer updated or switched to other sub pages Pressing the HOLD button again the current subpage appear CALLING UP SUBPAGE DIRECTLY Pee the SUBPAGE 29 button sub code appears beside page number Enter the subpage number that you want to call up with the NUMBER button 0 9 example the 2nd page sequence 0002 The desired subpage will eventually be displayed on the screen and holds it there Meanwhile whilst you are waiting it is possible to go back to the TV pic ture by pressing the CANCEL button on the remote and after a while press the CANCEL button again to revert back to the saved text sub page WATCHING TELEVISION DURING TELETEXT MODE Some pages are c
9. d Speaker Jack You can connect external speakers impedance 8 ohm nominal output power 12 watts min to this jack for improved sound quality Make sure that the polarity matches with the and mark on the speak er 12 TROUBLESHOOTING SYMPTOMS INSPECT ACTION Neither picture nor sound Is power code plugged in Press power button on front of TV If the red power light is on press the remote control power button Red power light should turn green Picture is OK but no sound Check if Volume Down is pressed Check if the Volume control is set to the minimum position Adjust the volume with Volume Up button Sound is OK but no colour Check if the color control is set to the minimum position Check if the program on air is in color or in black and white Check if the antenna installation and its connection is OK Check the antenna again Check by turning on other channel programs Reter to the color section again and readjust the color Overlapped Picture Image Check if the antenna direction is correct Check if the Fine Tuning function is set up correctly Direct the antenna toward the broadcasting station Adjust the Fine Tuning func tion SYMPTOMS INSPECT HANDLING Picture has Snow Check if the antenna is damaged or its connection is all right Check if there is interference from car traffic o
10. e wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red Do not make any connection to the terminal in the plug which is marked by the letter E or by the safety earth symbol L or coloured green or green and yel low SWITCHING THE SET ON AND OFF Switching On Switch the set on with the MAIN POWER ON OFF button The INDICATOR will illuminate in Red That means the set is on stand by mode Press PR UP or DOWN button on the front of set or POWER button amp PR UP DOWN button or one of the NUMBER button 0 9 on the remote controller The set will be switched on and then the INDICATOR will be changed in Green from Red Switching Off Press POWER button on the remote controller to return the set to its stand by mode f you don t use the set for extended periods of time turn it off with MAIN POWER ON OFF button ON SCREEN DISPLAY MENU The MENU button on the remote controller is used to call up the Main menu and also to return to either the Main menu or a previous menu You can call up the Main menu by pressing and holding down the TV AV button on the front of the set during 3 seconds The PR UP DOWN buttons on the remote controller on the front of the set are used to move the selection bar up or down the menus change data Position Access The Volume UP button on the remote controller or on the f
11. he mains cable into the power socket with 220V 240V 50Hz AC Additional Information for the set sold in Great Britain The appliance is supplied with a moulded three pin mains plug fitted with a 5 Amp fuse Should the fuse require replacement it must be replaced with a fuse rated at 5 Amp and approved by ASTA or BSI to BS1362 The plug contains a removable fuse cover that must be refitted when the fuse is replaced In the event of the fuse cover being lost or damaged the plug must not be used until a replacement cover has been obtained Replacement fuse covers can be purchased from your nearest electrical dealer and must be the same colour as the original If the moulded mains plug is unsuitable for the socket outlet in your home or is removed for any other reason then the fuse should be removed and the cut off plug disposed of safely to prevent the hazard of electric shock There is a danger of electric shock if the cut off plug is inserted into any socket outlet If a replacement plug is to be fitted please observe the wiring code shown below The wires in the mains lead are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not corre spond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter or coloured black Th
12. i NOT USE USED 60668 R DOLBY SURROUND NOT USED NOT USED e ROC Tao NOTUSED n6 G eee E CONTENTS E IDENTITY OF FEATURES ON LOCAL AND REMOTE CONTROL 1 IMPORTANT SAFEGUARDS n m I huh hh 3 B INSTALLATION Inserting Batteries into the Remote Control Unit e eee e ees 4 Aerial connection 4 Mains 4 Switching the set on and off n nnn 5 On screen display menu e n n nnne ner 5 Language selection n n nnne 5 Automatic Tuning the TV Channels s ns 5 Programme Edit e eher 6 Manual Channel Setting nnn 7 Fine tuning s nennen enne 7 09909090986 7 DAILY USE Recall I 8 Selecting a Programme Number 8 Picture Control lt lt lt IEEE 8 Sound Control lt 8 Timer I EB 9 Child Lock 10 Screen Format I n nsns 10 1 1 10 B TELETEXT nnn crete e 11 CONNECTING THE EXTERNAL EQUIPMENT 12 B TROUBLE SHOOTING m 13 B SPECIFICATIONS eect 14 IMPORTANT SAFEGUARDS Ventilation Do not cover the ventilati
13. ild locked after switching off the set by pressing the R G Y C the POWER button in sequence on the remote control within 5 sec onds The child lock function is indicated by flashing the INDICATOR on the front of set The set can only be switched back on using the remote control SCREEN FORMAT Whenever the Zoom button is pressed the screen will be changed as shown 16 9 gt 4 3 gt zoom gt panorama gt 16 9 STILL The Still button allows you to freeze the picture at anytime 10 Menu Picture Sound Timer Language Instal Clock Wake up Yes Time 00 05 Prog Prot Dg Retum lt gt Cursor TELETEXT SWITCHING TELETEXT ON OFF Press the TEXT button E The index page or the page viewed last will appear Press the TEXT button again to return to the TV mode COLOUR BUTTONS IN TOP FLOF TELETEXT Ared green yellow and blue field is shown at the bottom of the screen If TOP or FLOF Teletext is transmitted by the station pressing the correspond ing colour button on the remote controller you can select the desired page eas ily SELECTING PAGES The NUMBER button 0 9 are used to enter a page number The selected page number appears at the top of the screen and the page appears after a short time The UP D
14. on openings in the cabinet Never place the set in a confined space such as a bookcase or built in cabinet unless proper ventilation is provided Leave at least 10 cm around each side of the TV set Heat Never place the set near heat sources e g radiator Water Moisture Never install the set in the the bathroom or in a wet basement The apparatus should not be exposed to dripping or splashing water Do not place any containers with liquid e g flower vases on the set Object Entry Do not insert foreign objects such as needles and coins into the ventilation openings B Lightning Striking You should disconnect your set from the mains and the aerial system during thunderstorms E Cleaning Unplug the set from the mains before cleaning INSTALLATION If the set is moved or placed in a different direction the MAIN POWER button must be switched off for at least 15 minutes in order to take out a colour strain on the screen INSERTING BATTERIES INTO THE REMOTE CONTROL UNIT Press down the battery compartment grip and slide the cover Insert the batteries supplied two 1 5V type AAA Make sure that the polarity matches with the and marks inside of the bat tery compartment AERIAL CONNECTION For better picture and sound quality an effective aerial installation is the most important When using an outdoor aerial it is usually connected to the set by means of 75 ohm coaxial cable MAINS CONNECTION Plug t
15. ontinually updated for example stock market reports sports announcements and the latest news If you want to watch television and stay informed at the same time press CANCEL E3 button The regular programme is still visible and the teletext page number appears at the top of the screen Pressing the CANCEL button the teletext page appears with the updated infor mation REVEAL ANSWER This function can be used on certain pages to reveal the solution of riddles Press the REVEAL button E to reveal a hidden answer and press again to hide it DOUBLING CHARACTER SIZE Repeatedly pressing the SIZE button E doubles the character size in the fol lowing order Upper half of the page gt Lower half of the page gt Return to normal size 11 BRIGHTNESS AND CONTRAST CONTROL IN TELETEXT MODE Pressing the MENU button repeatedly in teletext mode the brightness and contrast control menu will be displayed in the bottom of the screen You can adjust these using the LEFT RIGHT button on the remote con troller DOUBLE WINDOW IN TEXT MODE You can simultaneously watch TV and Teletext screen by pressing the Zoom button in Teletext mode CONNECTING EXTERNAL EQUIPMENT SCART JACK 1 AV1 amp SCART JACK 2 AV2 amp SCART JACK 3 AVJS The SCART 1 is used to connect a VCR a Satellite receiver a Camcoder and a peri TV decoder The SCART 2 is used to connect a VCR a Satellite
16. r neon signs Correct the antenna faults or replace the connection cable Stripes on picture Check if there is interference by other electronic devices such as radio telephone etc Keep magnetic or electronic devices away from the set Bad stereo sound Long distance from the station or other radio waves could cause bad sound reception Shift the mode into Mono by using MTS button Operation disorder of Remote Control Check if the satteries are weak Check Remote Control Sensor window Get rid of objects blocking the TV sensor and Remote Control Replace batteries or check if the electrodes are fitting prop erly in the compartment 13 SPECIFICATIONS SYSTEM PAL I I SECAM L L NTSC 3 58 4 43MHz play back SCREEN SIZE 32 30 Viewable Real FLAT Tube MAIN VOLTAGE 220 240V 5OHz POWER CONSUMPTION Stand by mode 2 0 Watts Normal operating mode 180 Watts DIMENSION 890X572 5X560 mm SOUND SYSTEM Dolby Pro Logic SOUND OUTPUT Main L R 8 Watts Center SR SL 5 Watts NUMBER OF PROGRAM 100 programs 14
17. ront of the set used to call up sub menus adjust levels LANGUAGE SELECTION Press the Menu button to call up the Main menu Move the selection bar to the Language with UP or DOWN button Press the VOLUME UP button Then the languages will be displayed Press the UP DOWN button to choose the language you want Press the MENU button to return to Main Menu AUTOMATIC TUNING THE TV CHANNELS Call up the Install menu from the Main menu Install 1 Auto Seti Great Britain Place the selection bar on Auto setup and press the RIGHT button vena Tune Deutschland Then the country names will be displayed Fine Tune E Place the selection bar on the country you require with UP DOWN button ss Neder East Europe Others Position Start Return Press the RIGHT button Auto setup will begin your stations will be located and stored Please wait until the Edit menu appears wat If you don t want to edit programme now escape from menu with the MENU button You can do it later Auto Setup C02 Pr01 PROGRAMME EDIT The EDIT menu shows you information as follows Edit Programme position assignment Progamme number and Station name Pr Oh Picture Sound 5 Real channel number M Picture information PAL SECAM SECAM F BS uro SEN SSECA
18. sed to display the current status programme number station name sound system clock This display appear for 2 seconds SELECTING A PROGRAMME NUMBER The set has totally 100 programme numbers 0 99 The NUMBER buttons 0 9 are used for direct programme selection To select two digit programme press the second numbered button within two seconds You can also select a programme number by pressing step by step the UP DOWN buttons PICTURE CONTROL BRIGHTNESS CONTRAST COLOUR SHARPNESS Press the MENU button Press the RIGHT button to call up the Picture menu You can select each function with the UP DOWN buttons The levels of each function can be adjusted the LEFT RIGHT buttons to suit your viewing conditions the lightning conditions of the room and your preference For Hue control Tint is displayed only when receiving NTSC signal from external jack The adjusted levels are stored automatically at Favourite mode Smart Picture Selection When you press the NORMAL button repeatedly you can call up three pic ture settings stored in memory NORMAL I gt NORMAL II gt FAVOURITE gt hard picture soft picture user adjustable SOUND CONTROL VOLUME CONTROL Adjust the volume with the VOLUME 4 DOWN UP buttons on the front of the set or with the LEFT RIGHT button on the remote control MUTE Pressing the MUTE x button to turns the sound off The mute symbol will be displayed The sound returns
19. ton to change to MONO from STEREO Then the colour will be changed in Red Pressing this button again will change it back to stereo During a bilingual programme transmission pressing the Sound Mode but ton will change the language to the second channel DUAL II Pressing again will change it back to the main channel DUAL I TIMER SETTING THE CLOCK Position the selection bar to the Timer in the Main Menu Press the RIGHT button Place the cursor to Hour Minute with LEFT RIGHT button Set the hour minute with the UP DOWN buttons Place the cursor to Clock with LEFT RIGHT button and then press the Menu button to compelet Note that if you turn the TV off with MAIN POWER ON OFF button the clock setting is lost and must be reset if necessary Sound Equalizer Pro Logic Balance Center Surround Dolby Noise M Position Return Access Sound Equalizer Pro Logic Balance Center Surround Dolby Noise Favourite Music Speech Flat Position Retum Adjust Sound Equalizer Pro Logic Balance Center Surround Dolby Noise Normal Wide 3 Stereo Off Position Return Sound Equalizer Pro Logic Balance Center Surround Dolby Noise UR 00 Sound Equalizer Pro Logic Balance Center Surround Dolby Noise
Download Pdf Manuals
Related Search