Dacor Cooktop DRT366S User's Manual
Contents
1. 2009 Dacor all rights reserved Important Safety Instructions Important Information About DANGER Safety Instructions IMPORTANT If you smell gas Important Safety Instructions and warnings in Do not use or light any appliance this manual are not meant to cover all possible prob lems and conditions that can occur Use common sense and caution when installing maintaining or oper ating this or any other appliance From a neighbor s phone immediately call the gas supplier Follow the gas supplier s instructions Do not touch any electrical switch or use any electri cal devices including the telephone in your building Always contact the Dacor Customer Service Team about problems and conditions that you don t If you cannot contact the gas supplier call the fire stand See Customer Service Information department DANGER IMPORTANT Do not store or use combustible flammable or explosive vapors and liquids Such as gasoline on or in the vicinity of this or any other appliance Also keep items that could explode such as aerosol cans away from the cooktop Do not store flammable or explosive materials in adjacent cabinets or areas including above and below the cooktop WARNING WARNING NEVER use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating of the appliance Safety Symbols and Labe2. See page 3 The cooktop and shut off valve must be disconnected from the gas supply piping system during any pres sure testing exceeding 72 p s i 3 5 kPa The cooktop must be isolated from the gas supply piping system by closing the shut off valve to the cooktop during any gas supply piping system pres sure testing equal to or less than 75 p s i 3 5 kPa For LP gas installations the LP gas tank must have its own high pressure regulator in addition to the pressure regulator supplied with the cooktop 8 dacar Attach the gas pressure regulator included with the cooktop to the 3 4 19 mm male NPT gas inlet on the cooktop The inlet is located on the bottom at the right rear portion of the chassis For tight installations the regulator may be installed upstream from the pipe nipple anywhere between the shut off valve and the cooktop For best performance minimize gas pressure loss by attaching the regulator as close as possible to the cooktop gas inlet Complete connection of the gas supply to the cooktop by installing a minimum 72 flexible gas line not includ ed between the pressure regulator and the shut off valve Check for gas leaks Turn all cooktop control valves to the OFF position o on the gas supply valve and check all lines and connections for leaks using a soap and water solution or a gas leak detector o the gas supply valve off Installation Instructions Burner Componen
3. Amp 120 Vac 60 Hz COOKTOP WIDTH A DRT304S 29 7 8 759 mm DRT366S 35 7 8 911 mm Gas Supply Requirements Check your local building codes for the proper method of installation In the absence of local codes this appliance should be installed in accordance with the National Fuel Gas Code ANSI 2223 1 54 The gas service must be installed by a qualified profes sional Be certain that the cooktop being installed is correct for the gas service being provided natural gas or LP gas Also if operating the cooktop at an altitude above 4000 ft 1219 m make sure it is equipped for high altitude operation See the inside cover for more information An external manual shut off valve must be installed between the gas inlet and the cooktop for the purpose of turning on or shutting off gas to the appliance The factory provided regulator shipped with the appli ance must be installed in the gas line that runs from the gas shut off valve to the cooktop gas inlet Use only the regulator provided The regulator inlet accommodates a 3 4 gas supply line and is also compatible with a 1 2 house gas supply The inlet to the cooktop itself is equipped with a 3 4 male NPT fitting GAS SUPPLY PRESSURE REQUIREMENTS Manifold Minimum Gas Pressure Supply Pressure Natural Gas 5 Water Column 6 Water Column Propane LP pe tas 11 Water Column Maximum gas supply pressure for a
4. DRT304 VERIFY PROPER OPERATION AFTER SERVICING RL INDICATOR LIGHT 5s Ror 0 W Single Point Spark Module FL INDICATOR LIGHT 0 FL W Single Point Spark Module 120V 60Hz 0 254 POWER SUPPLY G RR INDICATOR LIGHT W B rs W RR Single Point RR Spark Module OSI RL 8 FR INDICATOR LIGHT W b 8 FR Single Point FR Spark Module N B O 83 FL B 11 sO H ES od ainpoyy weds weds weds affus 900 ajbuls M ud 0 24 M 0 93 MOLINO 14 ud a YOLVOIGNI 93 1H9IT801VOIONI 13 tS v 9 O c 8 94 ainpoyy enpoj weds Weds 8 juo juog E juod 96 Yy ou 0 M 0 JY YOLIND Td T 8 M 8 O M 8 ui P IH9ITSOINDIONI JH 1 YOLYIIONI TY 5 14 4 4 AdlH3A AlddNS aMOd VS8C 0 2809 WVYOVIG 9NISIM 12 dacar The Life of the Kitchen Dacor e 1440 Bridge Gate Drive Diamond Bar 91765 e Tel 800 793 0093 e FAX 626 403 3130 e www Dacor com
5. Do not leave children alone or unattended in the area around the cooktop Do not allow children to play with the controls or touch other parts of the cooktop Do not store items of interest to children on top of or above the cooktop Children could be burned or injured while climbing on the appliance Clean the cooktop thoroughly before operating it for the first time Make sure that all the cooktop parts are dry before lighting a burner Keep flammable items such as paper cardboard plastic and cloth away from the burners and other hot surfaces Do not place such items on the cooktop Do not allow pot holders to touch hot sur faces or gas burners Do not wear loose or hanging apparel while using the cooktop Do not allow clothing to come into con tact with the cooktop and surrounding areas during and immediately after use Do not use towels or bulky cloth as pot holders If the cooktop is near a window do not use long cur tains as window treatment The curtains could blow over the cooktop and create a fire hazard Non stick coatings when heated can be harmful to birds Remove birds to a separate well ventilated room when operating the cooktop IMPORTANT This appliance is equipped with a three prong grounding plug for your protection against possible electric shock hazards Plug it only into a dedicated grounded three prong electrical g 2 outlet It is the responsibility of the customer to make sure the p
6. AEB3612 for model DRT366S or non combustible material See the lat est version of ANSI 7223 1 Do not use this appliance in combination with a sur face countertop ventilation system Dacor strongly recommends the installation of a range hood in con junction with this appliance Do not install repair or replace any part of the cooktop unless specifically recommended in the liter ature accompanying it A qualified service technician should perform all other service Do not tamper with the controls Do not operate the cooktop without the knobs and trim rings in place Before servicing or installing this cooktop make sure that the gas supply is turned off at the gas supply valve and that the power plug is disconnected from the electrical outlet Disconnect the power plug from the electrical outlet before cleaning Clean this appliance only in the manner specified in the use and care manual Do not connect this cooktop to the gas supply with out the supplied gas pressure regulator installed Only use the cooktop for cooking tasks expected of a home appliance as outlined in the literature accom panying it This cooktop is not intended for commer cial or laboratory use DO NOT TOUCH THE SURFACES OF THE COOKTOP OR THE SURROUNDING AREAS DURING OR IMMEDIATELY AFTER USE 2 dacar WARNING Do not climb on any part of the appliance To avoid a fire hazard do not hang flammable or heat sensitive objects over the cooktop
7. Knob Installation Control Panel 1 Attach the SimmerSear burner knobs as shown DRT304S below The SimmerSear knobs have a wider space between the large flame icon and the simmer icon than the standard burner knobs Align the D shaped open ing on the back of each knob with the end of the valve shaft Carefully push each knob on until it stops 2 Attach the remaining knobs which operate the standard burners a_i SimmerSear Burner Knob Layout Standard Burner Knob Layout Gas Line Connection Control Panel DRT366S Within the Commonwealth of Massachusetts this appliance must be installed by a licensed plumber or gas fitter Verify that the gas _ meets specifications before connection See page 3 The maximum gas supply pressure to the regulator must never exceed pounds per square inch psi or 3 5 kPa Do not install or use the cooktop without the included gas regulator installed Ensure that the arrow on the regulator points in the direction of the gas flow towards the cooktop Do not apply excessive pressure when tightening gas connections and fittings Do not use Teflon tape or plumber s putty on flexible gas line connections Test the gas lines for leaks as instructed before use Do not use a flame to check for leaks The gas supply pressure for testing the regulator set ting shall be at least 1 inch water column 249Pa above the specified manifold pressure
8. base SimmerSear Burner Assembly Hole in burner ring Ridge on bottom es goes over igniter of burner cap Burner ring Igniter Burner base Standard Burner Assembly 9 Installation Instructions Veritying Proper Operation WARNING Make sure that power to the electrical outlet is turned off at the circuit breaker or fuse box and that the gas is turned off at the gas supply valve before proceed ing The cooktop must be properly grounded at all times when electrical power is applied Prior to operating the cooktop read the accompanying use and care manual carefully HIGH 1 Make sure all the cooktop burner con trols are in the OFF position 2 Connect the power Orr Low cord to the electrical outlet 3 on power to the electrical outlet at the circuit breaker or fuse box 4 Gently push in and turn one burner control knob at a time counterclockwise to the HIGH position Verify that the associated burner igniter sparks then return the knob to the OFF position Repeat for all of the remain ing control knobs Turn on the gas supply valve Perform the following ignition test for all of the burners Push and turn one of the control knobs counter clockwise to the HIGH position Only the igniter for the selected burner will spark It may take up to four seconds for the gas to ignite at which time the ignit er will stop sparking If ignitio
9. before you begin the installation process Leave these installation instructions with the customer e Customer Keep these installation instructions for future reference and the local building inspector s use Customer Service Information If You Need Help Product Data Label If you have questions or problems with installation contact your Dacor dealer the Dacor Customer Service Team For repairs to Dacor appliances under warranty call the Dacor Distinctive Service line Whenever you call have the model and serial number of the appliance ready The model and serial number are printed on the appliance data plate product data label contains the model and serial number information and the electrical and gas supply requirements e It is attached to the bottom of the chassis Model Identification Dacor Customer Service DRT366S NG H Phone 800 793 0093 U S A and Canada Monday Friday 6 00 a m to 5 00 p m Pacific Time SIZE nominal width in inches Web site www Dacor com GAS TYPE Dacor Distinctive Service repairs under warranty only NG Natural Gas Phone 877 337 3226 U S A and Canada LP Liquid Petroleum Monday Friday 6 00 a m to 4 00 p m Pacific Time Propane ALTITUDE H High Altitude Model 4000 ft 1219 m and up No character Equipped for low altitude operation All specifications are subject to change without notice Dacor assumes no liability for changes to specifications
10. cacor AHS Installation Instructions Distinctive Series Cooktop Models DRT304S DRT366S THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI 221 1 STANDARD FOR HOUSEHOLD GAS APPLIANCES Part No 106522 Rev B of Contents Important Safety Instructions 1 Installation Instructions eene 7 Important Information About Safety Instructions 1 Cooktop 7 General Safety 2 Gas Line Connection 8 Installation Requirements 3 Knob Installation 8 Electrical Requirements 3 Burner Component Installation 9 Gas Supply Requirements 3 Verifying Proper 10 Product Dimensions sse 3 Wiring 11 Cabinet and Countertop 4 Cabinet Cutout Dimensions 5 Before You Begin Important Installer In the interest of safety and to minimize problems read these installation instructions completely and care fully
11. ed to safely install it Unpack the parts box and verify that all required compo nents have been provided If any item is missing or dam aged please contact your dealer immediately Do not install a damaged or incomplete appliance The customer must report cosmetic issues within 30 days of installation Do not use a hardening compound or caulk to permanently seal the cooktop into place The cooktop Knobs see table below must be readily removable if service is required Removal of sealant to service the unit will be performed at the customer s expense Grates see table below Standard burner caps see table below 1 Lower the cooktop into the cutout while feeding the electrical cord into the utility cutout Center the cooktop SimmerSear inner burner caps see table below in the cutout Standard burner rings see table below SimmerSear outer burner caps see table below 2 Secure the cooktop to the countertop using the two 2 provided hold down bolts and washers provided Do SimmerSear burner rings see table below ertighten the bolts e Hold down bolts washers 2 sets e Regulator Dacor Stainless Steel Cleaner e Igniter cleaning brush Literature kit INCLUDED GRATES AND BURNER PARTS Quantity Quantity Part for Model for Model Knobs standards SimmerSear inner burner cap SimmerSear 1 2 outer burner 7 Installation Instructions
12. es the location of the existing utilities may be utilized provided they do not interfere with the sides or rear of the cooktop Check FIGURE 1 local building codes for permissible utility locations Combustible For best performance and to minimize gas pressure wall loss attach the gas supply regulator as close as pos Backguard mandatory if gap from back of cooktop to combustible wall is less than 2 1 2 FIGURE 2 Carefully check the location where the cooktop is to be installed For best performance the cooktop should be installed away from drafts caused by doors windows and heating and air conditioning outlets To reduce the risk of personal injury from reaching over a hot appli ance avoid cabinet installations directly above sible to the cooktop gas inlet The installation must Allow for access to the gas shut off valve and regulator when the unit is installed Allow for access to the electrical outlet when the cooktop is in place so that the power cord may be eas ily disconnected if the unit needs service Allow the 32 power cord to reach the electrical outlet Installation Requirements Cabinet Cutout Dimensions Cabinet tolerances 1 16 0 1 6 mm 0 unless otherwise noted 1 1 2 38 mm 10 254 mm to typical countertop combustible side thickness wall Min both sides 1 2 13 mm overhang A both sides Recommended 7 3 4 197 mm Co
13. ing problems caused by a faulty installation Installation Checklist WARNING To ensure a safe and proper installation the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked Proper installation is the responsibility of the homeowner The importance of proper installation of your Dacor cooktop cannot be overemphasized Is the electrical outlet for the cooktop grounded and located according to these instructions and in accor dance with all applicable electrical codes See pages 3 and 4 Is the gas service for the cooktop located and installed according to these instructions and in accordance with all applicable codes See pages 3 and 4 L Has the gas supply inlet pressure been measured to ensure that it does not exceed the maximums stated in these instructions See page 3 Is the cooktop secured using the provided hold down bolts and washers See page 8 Is the cooktop connected to the gas supply according to these instructions and in accordance with all appli cable codes Did the installer check the gas supply for leaks See page 9 L Are all burner parts and grates properly installed according to these instructions See page 10 Has proper operation been verified Has the warranty been activated on line or the warranty card filled out completely and mailed 10 dacar 72 U 9 O c WIRING DIAGRAM
14. ll models is 1 2 p s i Trim 28 1 8 714 mm _ _ 1 2 13 mm 4 25 7 8 657 mm thick a 1 5 8 41 mm cooking surface E 7 M height grate level above countertop 197 mm 5 Power cord 4 102 32 long 5 8 Min 16 mm 3 4 gas inlet connects to regulator from bottom or rear of unit end is recessed 2 51 mm from chassis bottom SIDE VIEW Product tolerances 1 16 1 6 mm unless otherwise noted 3 Installation Requirements Cabi net and Cou ntertop Lon rout e To reduce the risk of personal injury and to reduce accumulated smoke in the room Dacor strongly recom mends installing a range hood A hood should project forward a minimum of five 5 inches beyond the face of the cabinets WARNING To avoid the risk of fire or personal injury all minimum The installation must allow access to the underside and maximum specified clearances on this and the of the cooktop for service and inspection purposes following pages must be maintained or exceeded General Considerations The minimum distance from the back of the cooktop to a combustible rear wall is 2 1 2 64 mm minimum Figure 1 Installation of a non combustible material up to the hood or a backsplash is always recommended and mandatory if the distance
15. ls DANGER Immediate hazards that WILL result in severe personal injury or death WARNING Hazards or unsafe practices that COULD result in severe personal injury or death CAUTION Hazards or unsafe practices that COULD result in minor personal injury or property damage WARNING WARNING WARNING NEVER cover any slots holes or passages on the cooktop and cooktop chassis Doing so blocks TO REDUCE THE RISK OF INJURY TO PERSONS IN air flow through the cooktop and may cause carbon THE EVENT OF A RANGE TOP GREASE FIRE monoxide poisoning Aluminum foil linings may also trap a SMOTHER FLAMES with a close fitting lid cookie neat causing hazard siots holes and sheet or metal tray then turn off the burner BE passages clear of grease and grime CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE CALIFORNIA PROPOSITION 65 WARNING FIRE DEPARTMENT The burning of gas cooking fuel generates some NEVER PICK UP A FLAMING PAN you may be by products that are on the list of substances which burned are known by the State of California to cause cancer or DO NOT USE WATER including wet dish cloths or reproductive harm California law requires businesses towels a violent steam explosion may result to warn customers of potential exposure to such substances To minimize exposure to these substances always operate this unit according to the use and care You have a Class ABC e
16. n to combustible wall above countertop both sides 3 8 13 mm countertop overhang 1 2 13 mm gt 4 Gas electrical cut out in right rear corner of 9 mounting platform 8 W X 6 D 203 mm X 152 mm 1 2 13 mm m if gas and electrical are routed through bottom 625 S Hole 1 2 dia 13 11 7 16 5 2 places through platform l T 291 mm S for hold down bolts 1 8 O 1 thick mounting platform Min 2 51 mm ___ 1 25 mm Cabinet face below countertop overhang Cabinet Countertop Cutout Dimensions Top View Cooktop B Cutout D Hole Model Width Offset 30 13 3 8 BRI 762 mm 340 mm 36 16 5 8 914 mm 422 6 dacar Installation Instructions Unpack the Cooktop Cooktop Installation WARNING Ifthe gas and electric service provided does not meet the product specifications do not proceed with WARNING To prevent damage to the gas pressure regulator install it only after the cooktop is mounted in its per the installation Call the dealer the gas supplier or a 5 manent position licensed electrician Do not over tighten the hold down bolts Over tight ening the hold down bolts may result in improper operation of the dual gas burners The cooktop is heavy A minimum of two people are requir
17. n does not occur within four seconds turn the knob to the OFF position wait for at least five minutes to allow any gas to dissipate then repeat the test Once the burner lights the control knob can be rotat ed counterclockwise from HIGH to LOW to adjust the flame height progressively When the unit is installed properly the flame will be steady It will also have a sharp blue inner cone that will vary in length pro portional to the burner size The flame will be reduced by the Smart Flame feature under the grate fingers to increase grate life Normal Flame Appearance NOTE If the cooktop does not operate properly follow these troubleshooting steps Verify that power and gas are supplied to the cooktop Check to make sure that the power plug is connected to the electrical outlet and that power is turned on at the circuit breaker or fuse box e Check to make sure that all burner parts are properly seated burner continues to spark after ignition without stopping have a licensed electrician check the electri cal outlet for proper grounding or reversed polarity Repeat the burner ignition test If the appliance still does not work contact Dacor Distinctive Service at 877 337 3226 Do not attempt to repair the appliance yourself Be sure to have the model and serial numbers available when you call See the inside cover for location Dacor is not responsible for the cost of correct
18. oktop platform gas and electrical 1 25 mm Min service location 36 914 mm thickness consult local code typical Cabinet Countertop Dimensions Front View 13 330 mm Cooktop C Model 30 762 mm DRT304S 30 762 mm 36 914 6 DRT366S 36 914 mm Minimum Recommended NOTE Models DRT304S and DRT366S are not approved for installation with a raised vent Cutout for utility access finished counter Cabinet Countertop Dimensions ISO View 1 Vertical to combustible surface from cooktop grate level if installing an overhead vent hood also check the hood specifications for minimum required clearances 2 See Cabinet Countertop Dimensions Top View Continued on following 3 Not applicable for cabinets more than a horizontal pages distance of 10 254mm from the edge of the cooktop 5 Installation Requirements abinet Countertop Dimensions cont Cutout tolerances 1 16 0 1 6 mm 0 unless otherwise noted Gas and electrical connections at right rear section of chassis Gas connection and power cord may be routed through bottom or back of chassis Increase countertop and overhang additional 2 1 2 64 mm Min for Non combustible combustible rear wall above rear wall rear of countertop mounting platform N i 10 254 mm mi
19. roper type of outlet is un installed Do not under any circumstances Cut or remove the third ground prong from the power cord Use an adapter plug Use an extension cord Use a power cord that is frayed or damaged Connect to an electrical outlet with a ground fault interrupter GFI Installation Requirements WARNING Observe all governing codes and ordinances during planning and installation Contact your local building department for further information To prevent an electric shock hazard the power sup ply must meet the specifications stated below The electrical and gas supply data on this page is for refer ence only If the requirements below do not agree with the product data label use the data on the product data label Electrical Requirements electrical installation including minimum supply wire size and grounding must be done in accordance with National Electric Code ANSI NFPA 70 and local codes and ordinances A copy of this standard may be obtained from National Fire Protection Association 1 Batterymarch Park Quincy MA 02269 9101 The correct voltage frequency and amperage must be supplied to the electrical outlet according to the product data label located on the bottom of the chassis The electrical outlet must be installed by a licensed electrician ELECTRIC CIRCUIT REQUIREMENTS Circuit Required Total Connected Load 120 Vac 60Hz 15 Amp 3 wire 0 25
20. t Installation WARNING Never attempt to operate the cooktop with any of the burner parts removed Do not attempt to adjust the burner air mixture settings All adjustments are preset at the factory Remove the burner parts and grates from their shipping packages SimmerSear Burner Assembly Standard Burner Assembly 1 Install the SimmerSear burner ring s on top of the 1 Install the standard burner rings on the standard burner SimmerSear burner base s Line up the indentations bases There are two different sizes Put the hole on on the bottom of the burner ring with the pins on the the edge of each ring over the igniter Center the tabs top of the burner base on the bottom of each ring in the hole in the center of 2 Set the outer SimmerSear burner cap s on top of the each base burner ring s Make sure the burner ring is centered on 2 Install all the standard burner caps The ridge on the top bottom of each cap must surround the top of each ring 3 Set the inner SimmerSear burner cap s on the center Grate Installation of the SimmerSear burner base s Line up the ridge on the bottom of the cap with the pins on the center of the _ Gently set the grates on top of the spill trays Make sure burner base that the rubber feet are positioned in the dimples On model DRT366S the center grate is smaller than the other two Ridge on bottom of inner burner cap Outer burner cap Burner ring Pin on burner
21. to the back wall from the cooktop is less than 2 1 2 Figure 2 When installing a backguard use only Dacor model numbers AEB3009 or AEB3012 for model DRT304S AEB3609 AEB3612 for model DRT366S Consult local codes and ordinances for acceptable non combustible materials Combustible rear wall 2 1 2 64 mm Min to combustible rear wall including the ability to turn off the cooktop gas supply valve and electrical outlet All contact surfaces between the cooktop and the coun ter must be solid and level The countertop overhang on the sides of the cutout shown on the following pages covers the recessed por tions of the cooktop behind the control panel and cre ates a seamless look for the installation IMPORTANT When installing the cooktop into a lami nated or synthetic countertop radius the corners of the cutout to help avoid cracking Consult the countertop manufacturer s instructions for minimum corner radius reinforcement and heat protection requirements Gas and Electric Service Location The gas supply piping gas shut off valve and the elec trical outlet must be located so they do not interfere with the cooktop when it is installed If installing another appliance in the cabinet below allow for the routing of gas and electrical service out the back of the unit The shaded area on the facing page shows the rec ommended location of the gas inlet and the electrical outlet For replacement purpos
22. xtinguisher and you manual ensuring you provide good ventilation when already know how to operate it cooking with gas Use a fire extinguisher ONLY if The fire is small and contained in the area where it started The fire department is being called You can fight the fire with your back to an exit READ AND SAVE THESE INSTRUCTIONS dscor 1 Important Safety Instructions General Safety Precautions To reduce the risk of fire electric shock serious injury or death when using your appliance follow basic safety precau tions including the following WARNING Read the accompanying use and care manual com pletely before operating this appliance Keep packaging materials away from children Plastic sheets and bags can cause suffocation If you receive a damaged product immediately con tact your dealer or builder Do not install or use a damaged appliance This cooktop must be properly installed and ground ed by a qualified installer according to these instal lation instructions prior to use The installer should show the customer the location of the gas shut off valve and the power cord so that they know where and how to turn off the gas supply and disconnect power to the cooktop Proper installation is the responsibility of the customer Installations with less than 2 1 2 64 mm from the rear of the cooktop to a combustible material must use Dacor backguard model AEB3009 AEB3012 for model DRT304S AEB3609
Download Pdf Manuals
Related Search