Dacor 24GN User's Manual
Contents
1. 13 Feed the electric wire or cord into the utility hole in the side of the cut out Pull all of the slack out of the wire If the unit is to be connected directly to the house wiring e With power turned off at the circuit breaker or fuse box remove the house junction box cover e Feed the dishwasher wiring into the junction box o Secure the wire with a UL CSA approved strain relief Utility Cut outs Strip and connect the wires according to one of the wiring diagrams below e Tighten the strain relief Check to make sure the wire is secure e Replace the junction box cover and screws Wire or WARNING Connect the dishwasher ground wire to a separate properly grounded wire installed by a licensed electrician Feed the electric cord or wire and both hoses into the utility cut out s direction varies with installation A grounded cold water pipe must have metal continuity to an electrical ground and must not be interrupted by insulating materials Any insulating materials must be jumped with a length of No 4 To house circuit breaker copper wire securely clamped to bare metal at both panel or fuse box ends See diagram below Separate No 10 minimum To house circuit breaker copper ground wire panel or fuse box Junction box Wire nut 3 places a Fasten clamp tightly on pipe Wire nut 3 places No 4 copper wire Strain relie Strain re2. a Safe and proper installation the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked and the unit is working properly Proper installation is the responsibility of the homeowner The importance of proper installation of your Dacor dishwasher cannot be overemphasized Pre verification Check List Od O Confirm that the main power supply at the circuit breaker panel or fuse box is off Remove all packing material from inside the dishwasher Check the orientation of the bottom door seal The seal bulb should be facing into the tank If it is oriented towards the exterior of the door open the dishwasher door fully and orientate the door seal so that it is facing into the tank Familiarize yourself with operation of the dishwasher by reading the use amp care manual Remove any protective film if present from the control panel door panel etc Verify that all wiring is secure and is not being pinched or in contact with door springs or any other dishwasher components Verify that the dishwasher is level by pulling the lower rack half way out Let go of the rack and make sure it does not roll in or out If it does re level the dishwasher Add two quarts of water to the bottom of the dishwasher to lubricate the pump seal Turn on the water supply and check for plumbing leaks Tighten connections if necessary Verify that the door spring
3. cabinet Care should be exercised when the appliance is installed or removed to reduce the likelihood of damage to the power cord or hoses Before sliding the unit into the cut out make sure the hoses and wiring are positioned in the utility cut outs as shown on the facing page Level the Dishwasher Level the dishwasher using the adjustable legs on the front and back before sliding the unit into the cut out Measure the height of the front and back of the cut out with a tape measure Measure the height of of the front and back of the dishwasher Using a crescent wrench loosen the leg nut on all four legs and turn the legs to adjust them The maximum height of the dishwasher must be 1 8 lower than the maximum height of the cut out Leg nut Rear leg leg Remove the lower rack from the dishwasher and place a level on the tank side wall rack guides to verify the unit is level front to back To verify left to right level place a level on the front door jamb d Adjust the legs until the unit is level and does not exceed the height specifications in step 3 Tighten the leg nut to the chassis to secure the leg in place NOTE The leg nuts can be removed to make the dishwasher lower See page 10 dacor 9 Installation Instructions Installing the Unit in the Cabinet continued NOTE The leg nuts can be removed to make the dishwasher lower To do so e Turn the leg until it
4. empty before running the dishwasher To avoid damage to the racks do not let sharp edges come into contact with them This appliance is designed for installation by more than one person To avoid personal injury do not attempt to move or lift the dishwasher without assistance To prevent personal injury and damage to the unit due to it tipping over do not push down on the door anytime it is open To reduce the chance of tipping attach the anti tip brackets to the cabinet before operation Important Safety Instructions CAUTION Keep the factory installed high loop drain hose in place to ensure proper dishwasher operation Do not cut tie strap or lower it If it is necessary to lengthen it install an aftermarket drain extension kit available at most home improvement stores Design Specifications Product Specifications 20 to 120 psi 138 827 kPa ems Temperature 15 A 120 Vac 60 Hz dedicated grounded circuit See the model number label on product for total connected loaded Power Requirements Dimensions Tolerances 1 16 0 1 6 mm 0 unless otherwise stated SS 23 7 8 60 6 cm ED24 33 3 4 29 5 8 75 2 cm 85 7 cm ID24 to 26 7 8 68 3 cm 36 1 4 92 1 cm 1 5 8 4 1 cm Door in Lowered Position h 20 50 8 cm
5. gt Adjustable Toe Kick Le 23 3 4 60 3 cm Door style varies with model number See use and care manuals for 47 119 4 cm description Allows for hose on back of unit dacor 3 Preparing for Installation IMPORTANT Follow all cabinet and countertop minimum WARNING dimensions shown below to insure safe operation Observe all governing codes and ordinances during Prepare the installation location as shown below All planning and installation Contact your local building minimum product dimensions be must met or exceeded department for further information see page 3 Dimensions shown provide minimum clearances unless otherwise noted The floor must be level and all cut out surfaces must be Prepari ng the Location at right angles The dishwasher must be secured to the adjacent cabinets using the anti tip brackets for safety and Carefully check the location where the dishwasher is to be proper operation installed Put it in a location with convenient access Make certain that electrical power can be provided in the selected location Plan the installation so that the appliance can be removed if service is required Min Countertop 25 63 5 cm Fasten anti tip anchors into material under counter top and adjacen
6. acor PN 101934 If the panel requires decorative door hardware attach it before panel installation CAUTION To prevent corrosion and the possibility of the panel falling off use only stainless steel screws where instructed The provided mounting screws are designed for panels with a thickness of 5 8 to 3 4 Smaller panels may require different mounting hardware to prevent damage to the outside surface Failure to construct the custom panel and or toe kick as instructed on the template may result an improper fit and may prevent the door from closing properly CUSTOM PANEL INSTALLATION ID24 ONLY Installation Instructions Drain Line Installation 1 Connect the flexible drain line to the air gap or connect it directly to the waste tee or disposal see below 2 For installations without an air gap put a loop in the drain line as shown 3 Tighten the holding clamp For installations with an air gap check to make sure the drain line from the air gap to the disposal drain trap is complete and that the clamps are tight Create loop and fasten to under side of cabinet Floor INSTALLATION WITH AIR GAP AND DISPOSAL DISPOSAL INSTALLATION WITHOUT AIR GAP Create loop and fasten to under side of cabinet A Floor INSTALLATION WITH AIR GAP AND WASTE TEE WASTE TEE INSTALLATION WITHOUT AIR GAP dacor 11 Installation Instructions Verifying Proper Operation WARNING To ensure
7. al white power supply wire e Do not install a fuse in the neutral or ground circuit The dishwasher can be connected to A UL CSA approved grounded three prong receptacle if local code permits This method is the easiest to install OR Directly to the house wiring Hard wire the dishwasher according to local code directly to a three wire grounded single phase connection in a junction box NOTE In either case be sure the power cable or wire is long enough to remain connected when the appliance is removed from the cut out for service If the electrical service does not meet the specifications above e Have a licensed electrician prepare the electrical receptacle or junction box for final connection inside the adjacent cabinet according to the specifications above Plumbing Preparation e The water pressure must be between 20 and 120 psi 138 827 kPa The household hot water heater should supply a minimum of 120 F water to the dishwasher location for best results e Install a water supply valve for the hot water supply line where it is easily accessible after the dishwasher is installed The dishwasher is shipped with a 3 8 male compression fitting to facilitate installation Ww Hot Water Inlet Se BACK OF DISHWASHER e A flexible braided fill hose is highly recommended Co
8. all connections and restore the power Open the dishwasher door and verify that most of the water has drained If not verify that the disposer plug has been removed and or the air gap is not plugged Run the dishwasher through another fill and drain cycle Verify that there are no leaks If the dishwasher does not operate correctly see the instructions below If the fill wash and drain cycles operate properly reinstall the toe kick Adjust it so that the bottom of the chassis and the legs below the door are completely covered If the toe kick does not cover the chassis and legs completely install the included extended toe kick If the dishwasher fails to operate properly Verify that power is supplied to the dishwasher Check the electrical connections to ensure that the installation has been completed correctly For additional start up or drain problems check all installation steps to verify they are correct and complete Repeat the above test If the appliance still does not work contact the Dacor Customer Service Team at 800 793 0093 Do not attempt to repair the appliance yourself Dacor is not responsible for service required to correct a faulty installation cdacor The Life of the Kitchen Dacor e 1440 Bridge Gate Drive Diamond Bar CA 91765 e Tel 800 793 0093 e FAX 626 403 3130 e www Dacor com
9. amage may result from pinched wires or hoses Damage due to improper installation is not covered under warranty Install a 3 4 UL CSA approved strain relief on the base of the dishwasher junction box Strain Wire Make sure power to the electrical receptacle or junction box is off Before connecting the wiring and the plumbing push the dishwasher into position with the back of the unit about six 6 inches in front of the cut out Remove the two 2 screws that hold the toe kick assembly in place and remove it NOTE Do not reinstall the toe kick until the dishwasher is completely installed and tested Ground connection Junction Box Wiring 7 Strip the three 3 wires on the end of the electric cord or one end of the wire that will connect to the house wiring BoM 8 Feed the end of the wire or cord through th gh the dishwasher chassis into the junction box base through Toe kick the strain relief assembly 2 places 9 Loosen the grounding screw on the base and connect the green wire Tighten it into place 10 Connect the power cord or house wiring black and white wires to the black and white wires inside the junction box Match the colors Use wire nuts to connect them 11 Tighten the strain relief Pull gently on the wiring from the back to make sure it is secure 12 Replace the junction box cover and screw dscor 7 Installation Instructions Electrical Connection Continued
10. cacor Ln E Installation Instructions 24 INCH DISHWASHER Models ED24 ID24 MDH24 MDV24 PD24AG PD24BK PD24BU PD 24GN PD24SG PD24TS Part No 101891 Rev J All specifications are subject to change without notice Dacor assumes no liability for changes to specifications 2007 Dacor all rights reserved Table of Contents Before You Begin s ssssssssssssrssrnssrnssssnnsnnnnnrnnnrnn nr kn Ran Rn Rn nn nn 1 Plumbing PreparatiON sssssseessesrerrerrrrsressensrrrnnrrer rr enn n nr ora 5 Important Safety Instructions sssee semsrmersmrrrrn 1 3 Preparing the Drain ssmmssssssssssssesrenrsrrsssrnnsen ner r rr rn r rn arena nr ora 5 Important Information About Safety Instructions 1 Installation Specifications s sssssssssssrsrssrsrrnrrsnnnrnnnn 6 12 Safety Symbols and Labels nmsssnsssssssessrssssrerssssrerrsssrsr rr nr a 1 Verify the Package CONteMtS ssesesessrereerreserenennnn ann 6 General Safety Precautions messssssssessrssssrerssssrerrss nns sr nra 2 Electrical Connection isnnsressssessesrerrerrersrensnnnrer nns reser en rn nar nan 7 Design Specifications ssssssssssssssrsssnsnrnrssnnnnsnsn nn nn nanna 3 Plumbing Connections ss tmssssssrersessrrsrrssssrr rss saken sn nr snar rn 9 Product SpecifiCatiONS ssssessssssreersssreersssseersn as er rs arna 3 Installing the Unit in the Cabinet eee 9 10 Preparing for Installation 0 0 ccccccseeseeeseeeeeeeeeeeee
11. cations ILICI ERE Make sure you have everything necessary for proper installation before proceeding Serer os VN SSE Ne H 6 dacor Installation Specifications Electrical Connection 1 Retaining screw WARNING 4 Remove the dishwasher junction box cover screw The junction box is mounted to the dishwasher chassis Do not install the dishwasher unless the electrical below the door service provided meets the dishwasher specifications see page 5 A qualified technician must complete the installation of this built in appliance The owner is responsible to make sure the dishwasher is properly installed Improper connection of the electrical wiring may create an electric shock or fire hazard and may result in damage to the dishwasher s electrical system To avoid an electrical shock hazard turn off power to the electrical outlet or junction box at the circuit breaker panel or fuse box before proceeding Do not turn on the power or water supply until instructed to do so on the following pages Do not allow any material including the hoses or electrical wiring to be directly behind the dishwasher Junction Box Location while pushing it into the cut out opening Carefully pull the slack out of both hoses and the wiring from 5 Remove the junction box cover outside the cut out during push back to prevent 6 pinching An electric shock hazard or water d
12. comes out of the chassis Remove the nut from the leg e Re thread the leg into the chassis e Reach inside the chassis and thread the nut onto the top of the leg Slide the Dishwasher into the Cutout e Pull the electrical wiring and both hoses drain and water supply through the utility access hole in the side of the cabinet as you slide the dishwasher into the opening Stop when the dishwasher contacts the back wall or aligns with the front cabinet opening Install the Anti Tip Brackets CAUTION Make sure to anchor at least one anti tip bracket on each side of the dishwasher The anchoring material must be no more than 1 4 6mm from the anti tip bracket The anti tip brackets protect against possible tipping caused by heavy bottom rack loads on the door 1 There are anti tip mounting locations provided around the top and sides of the dishwasher front frame 10 dacor 2 To attach the anti tip bracket anchors insert the anchoring screws through the 1 2 diameter access holes inside the dishwashing compartment on the ceiling and the sides near the front Make sure that the anchoring screws pass through the anti tip brackets located on the outside of the dishwasher SS Top anti tip 6 bracket a Side anti tip bracket Cabinet Panel Installation Model ID24 Only Install the custom panel and or custom toe kick according to the instructions on the included template D
13. dealer or builder Use this dishwasher only for its intended purpose as outlined in the use and care manual It is not intended for commercial use Read the use and care manual completely before use Keep all packaging materials away from children Plastic bags can cause suffocation To avoid electric shock this dishwasher must be installed and grounded by a qualified installer in a completely enclosed cabinet according to these installation instructions All installation work plumbing connections and electrical wiring must be performed in accordance with all applicable codes and standards Install or locate this appliance only in accordance with these installation instructions The installer must show the customer the location of the fuse box or circuit breaker panel so that the customer knows where and how to turn the power off Before installing or servicing the dishwasher switch power off at the fuse box or circuit breaker panel and lock the electrical panel door to prevent power from being switched on accidentally When the circuit breaker panel cannot be locked securely fasten a prominent warning device such as a tag to the electrical panel Do not tamper with the controls Do not leave children alone or unattended in the area where the dishwasher is in use Never allow children to sit or stand on an appliance Do not let children play with this appliance Never allow anyone including children to sit or stand
14. ees 4 5 Drain Line Installation mmssssssssesrersrrrrrrrrsennsenrnrr nr rer rr enn nn na 11 Preparing the Location cc eceeeceeeeeeeeeeeteesnenaeees 4 Verifying Proper Operation cccceceeeeeeeeeeeeeeeteteees 12 Power Supply Preparation cccccceeeeeeeeeeeeeeseaeees 5 Before You Begin Important Installer In the interest of safety and to minimize problems read these installation instructions completely and carefully before you begin the installation process Leave these installation instructions with the customer If you have questions or problems with installation contact your Dacor dealer or the Dacor Customer Service Team Dacor Customer Service Phone 800 793 0093 Email customerservice Dacor com Web site www Dacor com Customer Keep these installation instructions for future reference and the local electrical inspector s use All specifications are subject to change without notice Dacor assumes no liability for changes to specifications Important Safety Instructions Safety Symbols and Labels DANGER Immediate hazards that WILL result in severe personal injury or death WARNING Hazards or unsafe practices that COULD result in severe personal injury or death CAUTION Hazards or unsafe practices that COULD result in minor personal injury or property damage Important Information About Safety Instructions e The Important Safety Instructio
15. lief To dishwasher Standard 3 Wire Connection 3 Wire Connection to House Junction Box with External Ground Does not apply when using a 3 Prong power cord To dishwasher Junction box Insulated Pipe Jumper if necessary 8 cdacor Installation Instructions Plumbing Connections 1 Connect one end of the 3 8 flexible braided fill hose to the water supply valve Route the hose through the utility access hole in the side of the appliance cut out Put the unconnected end of the hose over a bucket Turn on the water to clean any debris out of the supply line and fill the hose for leak testing Turn the valve off Keeping as much water as possible in the hose route it through the bottom of the dishwasher chassis and connect it to the water inlet Access the water inlet through the hole on the left side of the chassis Fill hose Water inlet Access hole in side Dishwasher Left Side 4 Turn on the water valve and check both ends for leaks 5 Using the included plastic fasteners attach the left side access panel NOTE The top edge of the access panel slides behind the chassis corner as shown below Chassis corner Slide this edge behind chassis corner Access panel 6 Slide the drain hose into the utility access hole in the side of the appliance cut out See facing page e Installing the Unit in the Cabinet Make sure the water valve is off before sliding the unit into the
16. nnect it to the unit just prior to installation into the cabinet e If copper tubing is present from a prior installation remove it and replace it with a flexible braided hose Preparing the Drain IMPORTANT A drain line hose is supplied with the product Should a longer drain hose be required use a hose approved for detergents and high temperature water The drain hose supplied with the dishwasher meets an AHAM DW 1 test standard Longer drain hoses should not be longer than 12 ft in length e You must install an air gap in the drain if the drain hose is connected to household plumbing lower than 20 in 50 8 cm from the floor or if required by local codes Plan for the air gap in the sink or countertop area adjacent to the dishwasher A section of drain hose not provided needs to be installed from the air gap to the disposal or waste tee e Ifan air gap is not required the drain hose must be installed to an inlet or waste tee above the drain trap in the household plumbing e The drain hose supplied with the dishwasher should be connected to a minimum 1 2 in I D drain connection e Ifthe drain is connected to a disposal see the disposal manufacturer s installation instructions for correct drain hose mounting techniques dacor 5 Installation Specifications Verify the Package Contents NOTE Model ID24 ships without a front panel It is designed for the installation of an integrated front panel that matches the su
17. ns and warnings in these instructions are not meant to cover all possible problems and conditions that can occur Use common sense and caution when installing maintaining or operating this or any other appliance e Always contact the Dacor Customer Service Team about problems and conditions that you don t understand See Customer Service Information DANGER WARNING To avoid the possibility of explosion or fire do not store or use combustible flammable or explosive vapors and liquids Such as gasoline inside or in the vicinity of this or any other appliance Do not store flammable or explosive materials in adjacent cabinets or areas The customer should not install repair or replace any part of the dishwasher unless specifically recommended in the literature accompanying it A qualified service technician should perform all other service Contact the nearest Dacor authorized service representative at 800 793 0093 or at www Dacor com for examination repair or adjustment dscor 1 Important Safety Instructions General Safety Precautions To reduce the risk of fire electric shock serious injury or death when using your appliance follow basic safety precautions including the following WARNING WARNING Do not install or operate this dishwasher if it has been damaged dropped has damaged electrical conduit or wires or is not working properly If the product is damaged when received immediately contact the
18. on any part of the dishwasher Stepping or sitting on any part of it may result in tipping damage and serious injury Many surfaces within the dishwasher achieve high temperatures Do not touch interior surfaces or items inside the dishwasher during or immediately after use Exercise caution when opening the door Let hot air and steam escape before looking or reaching inside 2 dacor Do not operate the dishwasher without the door completely closed and the toe kick panel in place Store all detergents and rinse aids out of the reach of children During loading insert all sharp or pointed objects with the handles up Locate these items where they will not damage the door seal or cause personal injury Do not tamper with the controls Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more Hydrogen gas is explosive If the hot water system has not been used for a period of time turn on all hot water faucets and let the water flow for several minutes to release any accumulated hydrogen gas Do not smoke or use an open flame during this process To prevent child entrapment always remove the door from an old dishwasher when removing it from service To prevent household mold and mildew damage periodically check the inlet and drain hoses for leaks If the dishwasher outlet is connected to a garbage disposal make sure the disposal is completely
19. rrounding cabinets e With the assistance of at least one person remove the dishwasher from the shipping carton Place the unit to the side of the cabinet opening e Remove all of the packing materials from inside and outside of the unit DO NOT allow any of the shipping materials loose screws or plastic to remain inside Remove the racks Set them aside for later installation Unpack the parts box and verify that all required components have been provided If any item is missing or damaged please contact the dealer immediately Do not install a damaged or incomplete appliance Extended toe kick Left side access panel 6 Plastic fasteners for access panel Use and care manual HIE GIGIEA Model ID24 only Integrated template screws and Seine door tensioning springs for heavy door panels Custom A bottle of Dacor Stainless Steel Cleaner is also on 0 Panel included with models having stainless steel doors Installation Tools required for installation Wire strippers Level Crescent wrench Phillips screwdriver HAEE Tape measure Materials required for installation not provided 2 wire nuts to fit wire mentioned above Additional wire nuts may be required for connection to house wiring 3 4 UL CSA approved strain relief Hose clamp for 1 3 8 OD drain hose 3 8 flexible braided fill hose required length varies ial Wire or three prong UL CSA approved electric cord see electrical specifi
20. s do not come in contact with any dishwasher components Verify the hot water temperature by turning on the hot water faucet at the sink The water going to the dishwasher must be between 120 F and 150 F Wet Test Check List Od O 12 Plug in the power cord if the dishwasher is equipped with one Turn on the main power supply Program the dishwasher to run a short wash See the use and care manual for specific operating instructions cacor O Close and latch the door L You should hear the dishwasher drain and then begin to fill with water Wait approximately two 2 minutes then carefully open the door to verify water is filling the dishwasher tank If there is water present close the door and continue the process Should the water not fill the tank or the pump is not running immediately push the START STOP button to stop the dishwasher Verify that the water supply valve is turned on power is connected and that main power supply is on Check for leaks under the dishwasher If any leaks are found immediately turn off the main power supply tighten all connections and restore the power Check for leaks around the door A leak around the door could be caused by the dishwasher door rubbing or hitting against adjacent cabinets Reposition the dishwasher if necessary The dishwasher will drain after the first fill Check the drain line for leaks If leaks are found turn off the power supply immediately tighten
21. t cablinets a a M y Cl Access Hole for Utilities 8 HX 5 D 20 3 cm X 12 7 cm i Ss l 24 61 0 cm CUT OUT FRONT VIEW CABINET INSTALLATION SIDE VIEW 4 decor Preparing for Installation Power Supply Preparation WARNING The electrical power supply for the dishwasher must be installed only by a licensed electrician as specified below It is the owner s responsibility to ensure that the electrical connection of this appliance is performed by a licensed electrician Electrical Specifications The electrical installation including minimum supply wire size and grounding must be in accordance with the National Electric code ANSI NFPA or latest revision and local codes and ordinances A copy of this standard may be obtained from National Fire Protection Association 1 Batterymarch Park Quincy Massachusetts 02269 9101 Power supply requirements e The dishwasher requires a grounded dedicated 120 Vac 60 Hz circuit protected by a 15 A circuit breaker or time delay fuse installed by a licensed electrician e It must be located to the right or left of the cut out in an adjacent cabinet so that power can be disconnected without removing the dishwasher e The ground terminal or lead on the appliance must be connected to a grounded metallic permanent wiring system or grounding conductor installed by a licensed electrician e Do not ground the appliance or appliance wiring to a gas pipeline or to the neutr
Download Pdf Manuals
Related Search