Home

D-Link DIV-140 User's Manual

Contents

1. Audio Configuration Help Codec Setting Codec Let 2nd 3rd 4th Priority fa711m7 6 7114 e729 6723 zl Buffer Settings Jitter Buffer Delay 150 0 to 500 milliseconds Packet Loss Rate 1 See Help Gain Settings Volume Tx Gain Rx Gain VoIP 0 o 15 to 40 dB PSTN 0 D See Help Tone 12 15 to 20 dB Fax Settings Fax Pass Through C Enable Disable Fax Relay C Enable Disable M FEC e Packet Redundancy Level C Ellipsis Other Settings Echo Tail Length 36 See Help Echo Delay Compensation K See Help VAD e Enable c Disable DTMF Mode Auto Mode 3 DTMF Pay Load 101 Range 96 to 127 Apply Cancel Fax Pass Through Fax Relay FEC Packet Redundancy Elipsis Echo Tail Length Echo Delay Compensation VAD DTMF Mode DTMF Pay Load In this mode of fax communication G711 codec is used Device will automatically switch to G711 codec on detection of FAX tone from the FAX machine In this mode of fax communication T 38 codec is used Device will automatically switch to T 38 codec on detection FAX tone from the FAX machine If both the modes of fax communication are selected then preference will be given to Fax Relay mode Following FEC Packet Redundancy Level and Ellipsis are configurable parameters for Fax Relay features This feature can be selected to activate forward error correction in T 38 Fax Relay communication This feature can be selected to activate p
2. Date and Time Time Configuration The time can be set to either Manual or NTP by selecting the maa mm daa we DIV corresponding radio button D Link Enter the domain name or IP address of NTP server Default pool ntp org Select the time zone from the drop down menu In manual mode the device date and time can be configured E here in YYYY MM DD Hrs Min Sec Year Month Date Hours Minutes Seconds format 10 0 0 1 Calcutta kA GI CU 2001 ox 01 oo J oo J oo D Link DIV 140 User Guide 18 NAT Configuration IP Sharing For the device to work behind NAT enable IP Sharing STUN or e TURN IP Sharing is simplest and can be used in the scenario D Link S a DIV where on the network router one to one static address mapping can be configured Global IP Address Configure here the global or external IP address of the network Contact your system administrator to get the global IP address NAT Traversal Traversal Note The router should be statically configured for one to one port mapping of ports in the RTP port range configured on the Network Configuration gt Media page and the VoIP Local port configured on the VoIP Configuration page i Fl Gi Stun Enable this to use STUN for resolving the bindings Primary Server Enter the IP address of the primary STUN server Port Enter the primary STUN server port in this field Default 3478 Secondar
3. No View Certificate D Link DIV 140 User Guide 10 When the login window appears enter the user name admin and then your Connect to 192 168 0 2 password The default password is password Click OK to continue User name If admin DI Password e I Remember my password en The System Information page will appear This will display information regarding your D DIV 140 device such as network settings pambaba e and firmware version The left column will contain the navigation menu The plus sign will indicate the section contains a sub menu Fl D Link DIV 140 User Guide 11 Device Configuration Country Select your country from the drop down menu Se D Link EE DIV Building Networks for People MP3 Feature Code Enter the feature code Speed Dial Enter the speed dial number Auto Log Off Time Enter the time in minutes to automatically log off i og D Link DIV 140 User Guide 12 Codec Priority Jitter Buffer Delay Packet Loss Rate Gain Settings Audio Configuration Here you can select the priority of audio codecs While establishing a call the DIV 140 will negotiate the highest priority of codec acceptable to both parties The administrator can choose from four codecs G 711 Mu and G 711 A provide the best voice quality but consume the most bandwidth G 723 consumes less bandwidth with some compromise on quality G 729 is a compro
4. SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN THE ENTIRE RISK AS TO THE QUALITY SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT Limitation of Liability TO THE MAXIMUM EXTENT PERMITTED BY LAW D LINK IS NOT LIABLE UNDER ANY CONTRACT NEGLIGENCE STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT INCONVENIENCE OR DAMAGES OF ANY CHARACTER WHETHER DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF GOODWILL LOSS OF REVENUE OR PROFIT WORK STOPPAGE COMPUTER FAILURE OR MALFUNCTION FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D LINK S PRODUCT IS CONNECTED WITH LOSS OF INFORMATION OR DATA CONTAINED IN STORED ON OR INTEGRATED WITH ANY PRODUCT RETURNED TO D LINK FOR WARRANTY SERVICE RESULTING FROM THE USE OF THE PRODUCT RELATING TO WARRANTY SERVICE OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY EVEN IF D LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT THE MAXIMUM LIABILITY OF D LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND A
5. DTMF Payload field In Info Mode DTMF packets are sent as SIP INFO Packets and in Auto Mode the mode of DTMF transmission is selected automatically to In Band Out Of Band or Info according to the remote ends capability Default Auto Mode Enter the payload type to use for out of band DTMF packets Range 96 to 127 Default 101 D Link DIV 140 User Guide 14 Timeout Dial Timeout Connection Timeout Alerting Timeout Interdigit Timeout Interdigit Time while Dialing FXO Rings Dial Termination Character Termination Call Configuration Various constants which are used during the call setup ke __ m aaaa aaa maximum timeout or number of rings can be configured in this D Link S DIV section Enter the maximum time to wait for a user to dial any key after going off hook After this timeout is reached an error tone is played to the user Range 5 to 120 seconds Default 15 seconds D D Enter the maximum time to wait to get any response from the other end During this period a progress tone is played and after the timeout limit is reached an error tone is played to the user Range 5 to 180 seconds Default 45 seconds D Enter the maximum time to play a ring back tone for outgoing calls when the called party starts ringing For incoming calls this field defines how long the phone will ring when user doesn t answer Range 5 to 120 seconds Default 60 seconds Enter the maximum time to wait in
6. default settings Using the CLI you can check the IP address of the device using the show nw ip command You can reset the device to factory default settings using restoredefaults command Another possibility is that the PC from which you are trying to access the web may not be in the same IP subnet as the device To confirm this you can try to ping the device from your PC Please contact your system administrator for details on how to configure your PC in same IP subnet 5 Why don t see some of the calls made or received on the System Monitor gt Call History page D Link DIV 140 User Guide 43 The call history is maintained in SDRAM and due to system limitations it is transferred to persistent storage only periodically approx every 1 hour The information displayed on the Call History page may not be accurate if the device is powered off before the call history is saved to flash Also due to memory limitations only the most recent 100 calls are stored in memory 6 Clicking links in the menu in the left frame of the web UI will not open that page This may happen if you perform a firmware upgrade The device can not be used during a firmware upgrade and you can only see the Upgrade Status page At the end of upgrade the HOME PAGE button on the Upgrade Status page is enabled Click that button to the web UI After a firmware upgrade is completed the web UI may not be reachable and will not load If this happens you can close th
7. device to be registered to server User ID User ID or phone number of the SIP client Usually this is the user part of the SIP URL Host IP Domain Enter the IP Address or domain name of the SIP client Port Enter the port address of the SIP client Default 5060 Example If the SIP URL of client is sip bob somedomain com 5060 then configure bob in User ID field somedomain com in Host Domain and 5060 in Port D Link DIV 140 User Guide 25 ACR ACR Automatic Call Routing is supported where in based nh XK _ lt aY number the calls can be routed to any destination The ACR D Link am DIV entries can be managed on this page It shows the list of ACR entries which are currently configured You can add delete or modify the ACR entries A maximum of 10 ACR entries can F be created Before configuring the ACR entry the required E E EE EE destinations should be added in destination table a 2 a ee met aa Edit Click on the Edit icon to modify the currently configured entry A new page will open with current configured values for fields Delete Click on the Delete icon to remove the existing ACR entry Add New Click on the Add New button to create a new ACR entry A new page will open Prefix The number starting with this prefix will be processed as per this ACR entry DLink oe DIV Minimum Digits The number will only match if it has minimum these many digits after prefix Maximum Digits
8. on FXO line after waiting for configured number of rings as in System Configuration gt Call page the device will automatically dial out to selected destination Select this to enable warm line connection to destination selected in drop down list If this feature is enabled then on getting an incoming call on an FXO line after waiting for a configured number of rings as on the System Configuration gt Call page the device will go off hook and play a dial tone to the user If the user doesn t dial any key for the configured time as in Timeout field then the device will automatically dial out to the selected destination Here user can specify how he wants to identify himself to the other end This value is useful if the receivers phone displays the calling party s number The receiver can contact the user using this number so this should be set to meaningful value If user wants to hide his identity then the field value can be set as Anonymous If this value is configured then the detected caller ID on the FXO port will be discarded and value in this field will be sent as user s identification This is what will be displayed on receiver s phone The port s phone number is the default value This can be set to any value like user s mobile number voicemail number etc If this value is configured then the detected caller ID on the FXO port is prefixed with this value and will be sent as user s identification The port s phone number is
9. ID Used to authenticate the port with SIP server This field accepts only letters digits hyphen and underscore and can be a maximum of 30 characters Authentication Used to authenticate the port with SIP server This field Password accepts only letters digits hyphen and underscore and can be a maximum of 30 characters User Parameter This feature will be supported in future releases D Link DIV 140 User Guide 30 Features Call Forward Always Call Forward On Busy Call Forward On No Answer Hot line Warm line Caller ID Caller ID Prefix Various features for all ports can be configured in this section Selecting the checkbox will enable the feature otherwise the feature is disabled Before configuring the following features except Call Waiting the required destinations should be added in destination table Enable this to redirect all incoming calls for this port to the configured destination in drop down menu Enable this to redirect all incoming calls for this port to the configured destination in drop down menu when this destination is busy Enable this to redirect all incoming calls for this port to the configured destination in drop down menu when the destination doesn t answer for Alerting Timeout as configured on the System Configuration gt Call page Select this to enable hotline connection to destination selected in drop down list If this feature is enabled then on getting incoming call
10. RE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES EXPRESS IMPLIED OR STATUTORY Governing Law This Limited Warranty shall be governed by the laws of the State of California Some states do not allow exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the foregoing limitations and exclusions may not apply This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state Trademarks D Link is a registered trademark of D Link Corporation D Link Systems Inc Other trademarks or registered trademarks are the property of their respective owners Copyright Statement No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from D Link Corporation D Link Systems Inc as stipulated by the United States Copyright Act of 1976 and any amendments thereto Contents are subject to change without prior notice Copyright 2006 by D Link Corporation D Link Systems Inc All rights reserved D Link DIV 140 User Guide 51 Contacting Technical Support U S and Canadian customers can contact D Link technical support through our web site or by phone Before you contact technical support please have the following ready e Model number of the product e g DIV 140 e Hardware Revisio
11. RESH button to reload the page with current status D Link DIV 140 User Guide GIG GIG e Building Networks for People Port Status Port Status Help Port PortType Cable Status Hook Status E Call Status atus 1 FXO NCE On Hook Not Registered Idle Disconnec t Connected Not isco 2 FXO Connected On Hook Not Registered Idle Disconnect 5 FXO Connected On Hook Not Registered Idle Disconnect 4 FXO On Hook Not Registered Idle Disconnect Connected 40 Save Changes Save Changes Each page on the web UI where configuration settings can be Le modified has an APPLY button Make the modifications and D Link S DIV click the APPLY button of every page where modifications are done To permanently save your changes click on the Save Changes button on this page Changes in some fields may require the device to restart the application and in that case the current calls will be disconnected So before saving make sure all calls are disconnected a n D i Save Changes Save and restart may disconnect your browser connection If Erezorscs the device IP address is changed then access the device web UI using the new IP address D Link DIV 140 User Guide 41 Restart System Restart System Click on the Restart button to restart the device Make sure the changes made in configuration are saved before doing so otherwise they will be lost Also the act
12. Restore to restore the configuration to the device D Link DIV 140 User Guide 36 Upgrade History Upgrade History Here you can see the history of software upgrades done on e this device It shows details like the upgrade file name server D Link DIV address time etc The table has the following columns as jm explained below Helo Upgrade History Upgrade File The name of upgrade file as entered by user when initiating upgrade Upgrade Server File Address S No Time Revision Status Upgrade History Records 0 0 of O P e le t La t GIG Ae GE Server Address The upgrade server address as entered by user when initiating i upgrade oarece Histon Time The system time when the upgrade was initiated Revision Version number of the new image for which upgrade is initiated Status This column shows Success if the upgrade was successfully completed It shows Failure if the upgrade was failed and Unknown if the upgrade status is not known This may happen if power went off during the upgrade process For detailed information about each upgrade click on the upgrade file name for that upgrade entry D Link DIV 140 User Guide 37 Call History Port Number Select Port Call Direction From To Direction Start Time Duration Status Here you can see the list of dialed outgoing calls and received P incoming calls for each port of device The detail
13. The number will only match if it has no more than these many digits after prefix Strip Digits If the above criteria is matched then this value will be the number of digits that will be stripped from the start of number before going ahead ana Toi Add Digits After stripping the digits from number the value configured in this field will be prefixed to the number before giving it to the configured destination After all the above the call will be routed to this destination entry Destination Example There is ACR entry with a prefix of 9800 minimum digits as 3 and maximum digits as 6 1 It will not match 98001 as there should be minimum 3 digits after prefix and here there is only 1digit after prefix 9800 2 It will not match 9800123456789 as there cannot be more than 6 digits after prefix and here there are 9 digits after prefix 9800 3 It will match 9800719 98001234 980078912 9800567890 etc D Link DIV 140 User Guide 26 Example The ACR entry with prefix as 9800 minimum and maximum digits as O will only match number 9800 Example Say if the calls starting with 5600 should be routed to destination USA Gateway but before routing the 5600 should be removed and number should be prefixed with 91 The number routed to gateway should be of exact 12 digits after 5600 For this routing add an ACR entry with prefix as 5600 minimum and maximum digits as 12 strip 4 digits as 5600 has 4 digits and add digits as 91 D Lin
14. USER MANUAL DIV 140 VERSION 1 0 ENEE a E a E aaa gt 7 7 D D gt CT O E TE aaa Tee ea a E E D Link BROADBAND Table of Contents a te e E 3 la gell AA AA AA 3 ST A Hardware DYE NEN esisin a aa i 5 Front Panel LEDS ic sesiicaaicasarsionsrarcrnabienupnenanehemenensiemonadys 5 Rear Panel Connections egenen ebessi 6 DVS CAAT OD E 7 Requirements EN 7 CONIC AAP aad 8 801 o 8 Li o Tu 9 Web based COnmQurattOMianiccecessateconctesnaasivoneepoueiususeaneed 10 Device Configuration aa naban hlayang 12 Audio Configuratio AA 13 Call el le Il CLA 15 Network CONnMIQUIANOM xccncosnecvsucesmsssnneeeraueneusnaucdarwensnts 17 TUS OM UNO a ANAND ea 18 NAT COMIC UPON sisson anenai 19 Media Configuration EE 20 VOIP COMET AMON EE 21 HUN GOUD am aaa NAA AN 23 IBT S dE 24 SL AA AA 26 Systemi Phone EE seccnnceeeenssconenesenssrosnnepemesauantareemndts 28 EE RR EE 29 POE Eelere E 30 POM Phone BOOK E 32 POR Sped Dial aii csitcnccnsccmsursiouarsnancananavancnseansnauiugsewebes 33 Login Contigurati EE 34 DC OU A E A 35 Device Management ssssssseseeesseserererensnssssssseseesseee 36 Upgrade E e EE 37 Call Ee EE 38 Port Su AA 40 D Link DIV 140 User Guide Save CANO CS AA 41 ST Sy SUI E 42 Troubleshooting aan Anna 43 Warranty aaa aanak 48 Contacting Technical SUPport cccseeeeeeeeeeeeeeeeeeeeeeeeeeeeees 52 Registration isiiininnninnninsnun
15. acket redundancy in T 38 Fax Relay communication This feature can be enabled to activate newer version of T 38 Fax protocol corrigendum 1 By enabling this feature device will be able to work with newer version fax devices The device cancels the echo generated by the hybrid of local telephone interface and phone set so that the other party connected to the channel will not hear the echo The parameters associated with echo cancellation can be configured here Note The default values should be good enough for most cases and it is recommended that you don t change it without assistance Echo Tail Length This specifies the time span over which echo is expected to arrive Tail length of 4 8 milliseconds is good enough for most cases Range 2 to 64 in steps of 2 corresponding to 1 to 32 milliseconds Default 36 i e 18 milliseconds This is used to properly align the delayed signal with reference signal Range 0 to 240 corresponding to 0 to 30 milliseconds Default 0 i e 0 milliseconds When this is enabled the DIV 140 detects a silence interval and uses silence compression to save on bandwidth This feature works irrespective of the codec selected Default Enabled There are four modes in which DTMF can be transmitted e In Band Mode e Out Of Band Mode e Info Mode e Auto Mode In In Band Mode DTMF packets are sent in band In Out Of Band Mode DTMF packets are sent as RTP Packets with different payload type as configured in
16. allation lack of reasonable care repair or service in any way that is not contemplated in the documentation for the product or if the model or serial number has been altered tampered with defaced or removed Initial installation installation and removal of the product for repair and shipping costs Operational adjustments covered in the operating manual for the product and normal maintenance Damage that occurs in shipment due to act of God failures due to power surge and cosmetic damage Any hardware software firmware or other products or services provided by anyone other than D Link and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D Link the sellers or the liquidators expressly disclaim their warranty obligation pertaining to the product While necessary maintenance or repairs on your Product can be performed by any company we recommend that you use only an Authorized D Link Service Office Improper or incorrectly performed maintenance or repair voids this Limited Warranty Disclaimer of Other Warranties EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN THE PRODUCT IS PROVIDED AS IS WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT D Link DIV 140 User Guide 50 IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD THE DURATION OF
17. ased Configuration To use the web based configuration utility you must use a computer either directly connected to the device using a cross over Ethernet cable or connected to the same network as the DIV 140 The default IP address is 10 0 0 1 If your network is using a different IP range you must first statically assign your computer an IP address of 10 0 0 2 subnet mask 255 0 0 0 and change the IP address of the DIV 140 to an available IP address of your network To change your computer s IP address please refer to the Networking Basics section in this user guide Open a web browser such as Internet Explorer and enter https 1 0 0 0 1 3 No page to display Microsoft Internet Explorer and press Enter File Edit view Favorites Tools Help Note You must enter HTTPS instead of HTTP D o O DA O Dm k Address https 10 0 0 1 18 E Go Link S Security Alert x If a security warning appears click Yes to continue I Information you exchange with this site cannot be viewed or amp changed by others However there is a problem with the site s security certificate A The security certificate was issued by a company you have not chosen to trust View the certificate to determine whether you want to trust the certifying authority A The security certificate has expired or is not yet valid A The name on the security certificate is invalid or does not match the name of the site Do you want to proceed
18. ature key sequence as 31 or 301 Assuming that force call disconnection key is 3 but the call is not terminated and the conversation is continued The force call disconnection feature by dialing in key sequence is not supported on FXO ports In this case to disconnect calls the user can access the web UI CLI or go on hook on to disconnect calls Miscellaneous 27 An FXO line is busy for a long time Calls to the FXO line are failing This may happen when the country code is not selected as per your PSTN environment The device uses busy tones played by the PBX as an indication to terminate the call and in a case where the country code is not selected properly the busy tone won t be detected If your country is not in list then you can choose country code OTHERS and configure custom parameters for all tones and line settings To release the PSTN line on the FXO you can select the Disconnect option on the System Monitor gt Port Status page This way the FXO port will be brought to an idle state D Link DIV 140 User Guide 47 Warranty Subject to the terms and conditions set forth herein D Link Systems Inc D Link provides this Limited Warranty e Only to the person or entity that originally purchased the product from D Link or its authorized reseller or distributor and e Only for products purchased and delivered within the fifty states of the United States the District of Columbia U S Possessions or Protectorates U S Milita
19. b G 729a with VAD and CNG support e G 711 u law and A law codec e G 711 Annex 2 Support for VAD and CNG e G 723 1 with 5 3 and 6 3 Kbps rates Voice Quality e IP layer TOS e Dynamic Adaptive Jitter Buffer algorithm e Packet loss concealment PLC e Echo Cancellation G 168 e Gain Attenuation settings Miscellaneous e Forced Call disconnection from WEB CLI by dialing in key sequence e Upgrade History Call History Port Statistics Display e HTTP TFTP software upgrade e Configuration Backup and Restore e Syslog Support e Restore to Factory Default Hardware Overview Front Panel LEDs Power LED Will illuminate when the device is powered on PSTN LEDs These LEDs show the status of the FXO ports If an LED is illuminated the phone is off the hook if it is not illuminated the phone is on the hook It will blink during a conversation or firmware upgrade LAN LED Will blink to indicate activity on the LAN port D Link DIV 140 User Guide Rear Panel Connections Console Used to connect the DIV 140 to the Com Port on your computer 10 190Tx LAN CONSOLE Reset Button LAN Port Press to reset the DIV 140 Comess BINA o to factory default settings BANGA or switch D Link DIV 140 User Guide Ss co lt gt Kc DID sm b PSTN 4 PSTN 3 PSTN 2 PSTN 1 PSTN Ports Four 4 FXO ports used connect to wall phone jacks to Power Receptor Receptor for Power Ada
20. between digits while dialing the number After this timeout further digits are ignored and the collected digits will be dialed out Range 1 to 120 seconds Default 5 seconds Enter the time between digits while dialing out the received number on FXO line using DTMF tones Range 50 to 1000 milliseconds Default 300 milliseconds Enter the number of rings to wait before going off hook on FXO port when the FXO port is ringing Range 1 to 9 rings Default 2 Note If this field is configured as 1 then caller ID detection on the FXO port won t work Here you can configure if any special DTMF key like or to use for terminating the dialed number while placing outgoing call Note that Inter Digit timeout will be always active Select enable if you want to terminate the dialed number using a DTMF key otherwise select Disable Default Enable If character termination is enabled then you can also terminate the feature access keys with this D Link DIV 140 User Guide 15 For example the feature key sequence to initiate call hold feature is 111 If character termination is enabled to then you can dial 111 for the same Character Enter the character to use for termination Range 0 to 9 or Default Default Route Here you can configure how calls should be routed Route all calls to Enable this if all calls including calls to local FXO ports should be routed to the VoIP server Default Enable VoIP Server Note If this fi
21. ce paid that is attributable to the Software Except as otherwise agreed by DLink in writing the replacement Software is provided only to the original licensee and is subject to the terms and conditions of the license granted by D Link for the Software Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions If a material non conformance is incapable of correction or if D Link determines in its sole discretion that it is not practical to replace the non conforming Software the price paid by the original licensee for the non conforming Software will be refunded by D Link provided that the non conforming Software and all copies thereof is first returned to D Link The license granted respecting any Software for which a refund is given automatically terminates Non Applicability of Warranty The Limited Warranty provided hereunder for Hardware and Software portions of D Link s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D Link the sellers or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case the product is being sold As Is without any warranty whatsoever including without limitation the Limited Warranty as described herein notwithstanding anything stated herein to the contra
22. ct is incapable of correction or if D Link determines that it is not practical to repair or replace the defective Hardware the actual price paid by the original purchaser for the defective Hardware will be refunded by D Link upon return to D Link of the defective Hardware All Hardware or part thereof that is replaced by D Link or for which the purchase price is refunded shall become the property of D Link upon replacement or refund D Link DIV 140 User Guide 48 Limited Software Warranty D Link warrants that the software portion of the product Software will substantially conform to D Link s then current functional specifications for the Software as set forth in the applicable documentation from the date of original retail purchase of the Software for a period of ninety 90 days Software Warranty Period provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation D Link further warrants that during the Software Warranty Period the magnetic media on which D Link delivers the Software will be free of physical defects The customer s sole and exclusive remedy and the entire liability of D Link and its suppliers under this Limited Warranty will be at D Link s option to replace the non conforming Software or defective media with software that substantially conforms to D Link s functional specifications for the Software or to refund the portion of the actual purchase pri
23. cted to the port This can happen if the device is not able to detect a ringing tone Please make sure that the ringing frequency value for your PBX CO is between 16 Hz and 30 Hz This can also happen if the device is connected to digital PBX CO lines Please make sure it is connected only to analog lines 20 A call is established with an FXO port successfully But once the remote PSTN end user has ended the call by going on hook the call on the VoIP side is not ended This can happen if the device has failed to detect busy tone or error tone on that particular FXO port so the FXO port is still in on hook state Users can use the web UI CLI or the Force Call Disconnection feature key to disconnect a call on that particular port 21 My call from a DIV 140 end point is getting disconnected if my call duration is more than 3 Hrs Maximum call duration of any call from to FXO end points of the DIV 140 is 3 hours After this time any call will be disconnected Features 22 am dialing a feature code but the feature is not working Please check the following e To access the feature call hold and call transfer key sequences should be prefixed with a feature code For example if 777 is the call hold key sequence and the feature code is then you should dial 777 e f you dial 777 then the other end will be put on hold only after the Interdigit Timeout To make it faster you can set the character termination to and dial 111 The other
24. e browser open a new browser window and access the web UI using its IP address To see the upgrade status you can go to System Monitor gt Upgrade History page 8 When I try to login to the DIV 140 am getting the Server Busy page What should I do If you get this page it means that someone else is already logged into the DIV 140 or the browser window was closed without logging out properly You may have to wait for the Auto Logoff time to pass in order to access the device again or reboot the device You may want to configure a low Auto Logoff time for this problem 9 was logged in and was using the DIV 140 When I tried to access any pages it gave me a You have been successfully logged out page If your session has been idle and the Auto Logoff time has exceeded and you click on any of the pages then you will get the Session Time out page You can close the browser open a new one and access the DIV 140 again You might also get the Session Timeout page if the device was restarted in between Calls 10 When dialing from VoIP to FXO the number is not dialed out hear a dial tone from the PBX CO on the FXO side or I hear complete silence followed by a fast busy tone This may happen when the time between dialed digits is too small on the FXO port and the PBX is not able to differentiate digits Check the value of Inter Digit Time while Dialing field on the System Configuration gt Call page in the web UI as it
25. e empty Click on the Cancel button if it is not empty Enter a valid phone number and select a destination from drop down menu and click on the Add button to create new phone book entry Phone Number This is the number which users will dial to place call to this phone book entry Destination This is the drop down menu of configured destinations Select a destination entry for this phone book configuration D Link DIV 140 User Guide 32 Port Speed Dial Port Speed Dial Here you can manage the per port speed dial entries When e any of the ports dial a speed dial feature access code followed D Link DIV Building Networks for People by a speed dial number then the destination corresponding to that speed dial number entry if found will be dialed Port Speed Dial Help This page shows the list of entries which are currently EE DE configured You can add delete or modify the speed dial entries Speed Dial Number Tt Destination Example 1 S A maximum of 10 entries can be created Before configuring add New Update cancet the speed dial entry the required destinations should be added f ane AA REAT T in destination table d 1 7145551122 Example 1 D o Edit Click on the Edit icon to modify the existing speed dial entry The corresponding values will be loaded in Phone Number text box and Destination drop down menu will show the current configured destination for that entry You can modify any
26. eld is enabled then the calls to local FXO ports will fail if the VoIP server is not available D Link DIV 140 User Guide 16 Network Configuration IP Mode Select a method to obtain an IP address from Static HP and PPPoE option If the Static option is selected then a user D Link or DIV configured IP address Net Mask gateway and DNS server addresses would be used If DHCP or PPPoE is selected then these values will be obtained using DHCP or PPPoE Default Static IP Address This specifies the IP address of the DIV 140 Default 10 0 0 1 E 92 168 0 1 Net Mask This specifies the net mask of the DIV 140 Default 255 0 0 0 92 168 0 1 GR Gateway This specifies the gateway of the DIV 140 Default 10 0 0 1 0 0 0 1 i Primary DNS Server This specifies the primary DNS Server of the DIV 140 Default 10 0 0 1 Secondary DNS Server This specifies the back up DNS Server of the DIV 140 This is used in case the primary DNS server is not responding Default 10 0 0 1 Calcutta PPPoE Username This username is used in PPPoE mode to authenticate with a o0 J oo _ oo PPP server PPPoE Password This password is used in PPPoE mode to authenticate with a PPP server Idle Timeout If the PPPoE session is inactive for the time specified in this field then the session will be terminated Range 0 to 86400 seconds Default 900 seconds D Link DIV 140 User Guide 17 Mode NTP Server GMT
27. end will be put on hold The same applies for call transfers also D Link DIV 140 User Guide 46 23 Why is caller ID is not being detected The PSTN network should generate the caller ID The number of FXO rings in System Settings gt Call page should be more than 2 for the caller ID detection to work Also the country code should be set to the proper value as per the telephone network characteristics H your country is not in the list you can choose country code OTHERS and select the proper caller ID specification on the Tone Settings page Please note that DTMF caller ID is not supported 24 The peer to peer calls are not working Whatever I dial is always sent to the VoIP server Please check that the route all calls to VoIP server option is disabled The peer to peer calls won t work if it is enabled and the destination number will be redirected to the VoIP server 25 Can I route all calls to an FXO port from the VoIP side to a particular PSTN number DID To support this you can use the ACR table For example if 9901 is the FXO port 1 s phone number then you can add an ACR entry prefix 9901 min 0 max 0 strip 4 add 132 and route to FXO port 1 When anyone dials 9901 from VoIP side then call will be automatically diverted to extension number 132 on the PBX 26 When making a call from DVG FXO port no 1 a conversation with the destination side has started To disconnect the current call dial the force call disconnection fe
28. h a server In VoIP server mode each port can be configured with different account or the feature can be enabled to use same account for all ports With backup server configuration support the device can still work in absence of primary server The support for STUN and IP Sharing enables the device to work behind NAT It provides secure web based management interface with administrative and restricted accesses to remotely configure and monitor the system The configuration backup facility helps in maintaining multiple configurations for the device D Link DIV 140 User Guide 3 Features Following features are supported Protocols e SIP RFC 3261 Compliance e STUN and IP sharing support for NAT e RTP and RTCP e DTMF Tx Rx support using SIP INFO or Out of Band as per RFC 2833 e Fax Support using T 38 Fax Relay and Fax Passthrough e NTP to keep device time in synchronization e DNS SRV RFC 3263 compliance Features e DTMF generation and detection e Fax tone detection e Caller ID Detection and Generation e Custom Caller ID Configuration e Detection and generation of user specified tones e Polarity Reversal Generation Call Features e Consultation Call Hold e Attended and Unattended Call Transfer e Call Forward Always on Busy on No Answer e Call Waiting e Hot line and Warm line e ACR e Hunt Group e Speed Dial System wide and per port e Phone Book System wide and per port D Link DIV 140 User Guide Audio Features e G 729a
29. has a valid Ethernet connection to a PC or LAN via its Ethernet port We recommend using a recent version of the above mentioned browsers The browser must have JavaScript enabled You must make sure the PC is in the same IP subnet as this device 10 0 0 1 You can do this by changing the IP address of the PC Type https 10 0 0 1 in the web browser address bar to access the web UI Login with default user name and password as admin and password Refer to the Web Configuration section of this manual or online help for further details The network related parameters can also be configured through the CLI Using a terminal emulator on your PC you can modify these parameters as per your network settings For examples and details of commands used here you can refer to CLI Commands section of this manual Type question mark to see the online help of command A Enter user name as admin and password as password Type help to see the list of available commands Type show nw to see the current network settings Change the IP mode using command set nw mode If IP mode is static IP use set nw ip to set the new IP If IP mode is PPPoE use set pppoe auth to set the user name and password Type save to save the changes onmoon Now you can access the web interface of device using the new IP you have configured Type https lt IPAddress gt in your browser D Link DIV 140 User Guide 9 Web b
30. imary Server Address Port Secondary Server Port Registration Timeout Uri Scheme Transport Use Same Authentication for All Channels Phone Number Display Name Authentication User ID D Link DIV 140 User Guide VolP Configuration The SIP Server specific parameters are configured here If there is no SIP server being used then the fields in this section can be left empty D Link Building Networks for People SIP Configuration Enter the IP address or domain name of the primary SIP server Default www sipproxy1 com Server Settings Primary Server Server Address www sipproxy1 com Enter the primary SIP server port in this field Default 5060 aen 5060 Secondary Server Server Address www sipproxy2 com VoIP Configuration Enter the IP address or domain name of secondary SIP server This is used as backup in case if primary server is not reachable Default www sipproxy2 com Server Port 5060 Registration Timeout 3600 In seconds Uri Scheme Transport Enter the secondary SIP server port in this field Default 5060 Authentication Parameters C Phone Number Use Same Authentication for All Channels d ei Display Name This specifies the interval at which the registration should be updated with server Range 40 to 2000000 seconds Default 3600 seconds Authentication User ID Authenticatio
31. ive calls will be disconnected Save and restart may lose your browser connection If the device IP mode is changed then access the device GUI using the new IP address D Link DIV 140 User Guide Building Networks for People DIV 42 Troubleshooting TIP If you face any issues with this product please read the corresponding section of user manual Configuration 1 What is the default username and password to login to the DIV 140 The default username and password are admin and password The same can be used on both web https and CLI interfaces If this is not working then you can reset the device configuration to factory default settings by pressing the button on the rear panel of the device Please note that you will loose your configuration settings 2 Why won t my configuration changes go into effect Make sure that you click on all pages where you have made changes After you have made all configuration changes browse to the Save Changes page and click the Save Changes button The DIV 140 will restart and your configuration changes will take effect 3 What if the Authentication Parameters on the Port Configuration gt General page are disabled In order to configure the Authentication Parameters the Use Same Authentication for All Channels field must be enabled on the VoIP Configuration page 4 am not able to access the web UI using the default IP address 10 0 0 1 The DIV 140 may not have the factory
32. k DIV 140 User Guide 27 System Phone Book Phone Book Here you can manage the system phone book common to all e FXO ports When any of the ports dial the number tomakean D Link DIV Building Networks for People outgoing call it is checked if there is any phone book entry corresponding to that number If entry is found then the call is placed to that destination System Phone Book Help Phone Number ess Destination Example 1 x 8 E 3 5 Add Update Cancel This page shows the list of entries which are currently S No Phone Number Destination Edit Delete configured You can add delete or modify the phone book entries A maximum of 10 entries can be created Before configuring the phone book entry the required destinations should be added in the destination table 1 2135551234 Example 1 CN a Edit Click on the Edit icon to modify the existing phone book entry Gin Book The corresponding values will be loaded in Phone Number E text box and Destination drop down list will show the current configured destination for that entry You can modify any of the two fields and click Update button to apply the changes At any time you can click on Cancel button to discard the changes Delete Click on the Delete icon to remove the existing phone book entry Add New To add a new phone book entry the Phone Number text box should be empty Click the Cancel button if it is not empty Enter a valid phone number and
33. may be too small Increase this and retry the calls D Link DIV 140 User Guide 44 11 Why do I hear a dial tone even though I have not dialed an FXO number The same happens on any VoIP number dial In case of network failure or failure while registering to the VoIP server the outgoing calls will be routed to the first free FXO line if the Use FXO as lifeline option is enabled on the System Setting gt Call page 12 hear a fast busy tone as soon as go off hook on a phone connected to an FXS port The hotline feature is likely enabled for that FXS port You can disable the hotline feature on the Port Configuration gt General page 13 After dialing 12345 to call another person hear a progress tone after 5 seconds Can I make it faster You can configure the nterdigit Timeout option on the System Settings gt Call page to a lower value You can also set the character termination to a character ex and dial 12345 to quickly place the call 14 I am dialing 12345 to call another person with number 12345 but the call will not go through Please check that you have enabled character termination and the corresponding terminating character is In this case you can enable the character termination or just dial 12345 no to call the other party 15 My number for the FXO port is 7901 and I am trying to dial to VoIP number 7901234 Why is the call is going to the FXO port If the dialed number starts with the FXO port phone nu
34. mber then the call will be by default routed to the FXO number This is to support the single stage dialing to PSTN phones through the FXO port To override this feature you can add a phone book entry with the number as 7901234 16 During an FXO to VoIP call why do hear loud echo on the VoIP side This can be because of a mismatch of the PSTN network and the DIV 140 configuration Please make sure that you have configured the proper country code on the DIV 140 If you still have the echo problem choose the country code Others and under Tone Settings you can try configuring different values for the line impedance field as per your network characteristics 17 Why are FAX transmissions Send Recieve through the DIV 140 failing Two things need to be configured on the DIV 140 for FAX communications The device audio codec list configuration should have the D Link DIV 140 User Guide 45 G 711 codec and the VAD option should be disabled for reliable transmission of FAX over IP 18 When we initiate a call from a VoIP phone to an FXO port we get a dial tone However when pressing the DTMF keys on the VoIP phone the number is not dialed out Also the dial tone doesn t stop This can happen if DTMF keys are transmitted as in band Please make sure that out of band DTMF is enabled on both the DIV 140 and the VoIP phone 19 The FXO port is not going off hook and it is not giving a dial tone when dial the number of a PBX CO line conne
35. mise between both It uses significantly less bandwidth as compared to G 711 and gives better quality as compared to G 723 The Jitter Buffer monitors network conditions and implements a delay profiling algorithm that provides better tracking of adaptive jitter buffer and improves voice quality The jitter buffer automatically determines the network jitter maintains the desired packet loss rate subject to the limit of the maximum allowed jitter delay These parameters can be configured here The Jitter Buffer Delay specifies the maximum desired jitter delay in milliseconds Range 0 to 500 milliseconds Default 150 milliseconds Specifies the allowable packet loss rate in 0 1 units Range 0 to 50 corresponding to 0 1 to 5 0 Default 1 0 1 The volume settings at various levels can be configured here Here Tx field specifies stream going from this device to IP network and Rx specifies the stream coming to this device from the IP network VoIP Increase this value to digitally amplify the signals Range 40 dB to 15 dB Default 0 dB PSTN Increase this value to amplify the signals at analog level Range O or 1 corresponding to O and 6 dB Default O Tone Modify this value to set the volume level of tones Range 20 dB to 15 dB Default 12 dB D Link DIV 140 User Guide D Link Building Networks for People
36. n located on the label on the bottom of the device e g rev A1 e Serial Number s n number located on the label on the bottom of the device You can find software updates and user documentation on the D Link website as well as frequently asked questions and answers to technical issues For customers within the United States For customers within Canada Phone Support Phone Support 877 354 6555 800 361 5265 Internet Support Internet Support http support dlink com http support dlink ca D Link DIV 140 User Guide 52 Registration Pi e kb KI JUL E ee Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights Version 1 0 September 6 2006 D Link DIV 140 User Guide 53
37. n Password User Parameters Outbound Proxy Note When STUN is enabled this field should be set to a value smaller than the binding inactivity timeout on the NAT Router This way the binding for SIP local port will be kept alive Server Address Server Port Local Settings Local Port 5060 This feature will be supported in future releases Use DNS SRY Subscribe for message waiting indication SOO Unregister at BootUp This feature will be supported in future releases Enable this to use the same authentication parameters specified in this section for all ports Enabling this setting will disable all authentication fields on the Port Configuration 5 General page Default Disable This specifies the phone number using which other devices can call this device This field accepts only numbers and can be a maximum of 20 characters This is used only for display purposes This field accepts only letters digits hyphen and underscore and can be a maximum of 30 characters Used to authenticate the device with a SIP server This field accepts only letters digits hyphen and underscore and can be a maximum of 30 characters 21 Authentication Used to authenticate the device with a SIP server This field accepts only letters digits hyphen and underscore and can be a maximum of 30 Password characters User Parameter This feature will be supported in future releases Outbound Proxy Thi
38. n click on the Cancel button to discard the changes Delete Click on the Delete icon to remove the existing speed dial entry Add New To add a new speed dial entry the Phone Number text box should be empty Click on the Cancel button if it is not empty Enter a valid phone number and select a destination from drop down list and click on the Add button to create new speed dial entry Phone Number This speed dial entry can be accessed using this number Destination This is the drop down menu of configured destinations Select a destination entry for this speed dial configuration D Link DIV 140 User Guide 29 Port Configuration Port Number Here you can configure the authentication parameters to P register with VolP server and different features of each port D Link DIV Select the port from this drop down list Authentication These parameters are used to authenticate the ports with Parameters VolP server during registration or while making calls If Use Same Authentication for All Channels field is enabled in VoIP Configuration page then these fields are not editable Phone Number This specifies the phone number using which other devices can call this port This field accepts only numbers and can be of maximum 20 characters Display Name This is used only for display purposes This field accepts only letters digits hyphen and underscore and can be of maximum 30 characters Authentication User
39. nununnninunisaai nasisa ininanaanaaid dadina inania 53 Product Overview Introduction The D Link Analog Trunk Gateway DIV 140 is a full featured multi port SIP based VoIP gateway It links traditional telephone network and IP network Using the DIV 140 you can explore the wide features of VoIP technology It enables you to make and receive calls through a low cost VoIP network using a conventional telephone network setup The advanced technology behind the DIV 140 presents a highly scalable and flexible architecture to cater to the needs of varied market segments The highly flexible call routing settings allow the administrator to configure different routes for calls based on the dialed number It provides configuration to route all local PSTN numbers through PSTN lines and all long distance calls through different VoIP networks Both proxy based calls and peer to peer calls are supported simultaneously It supports per port phone book and system phone book to place peer to peer calls without going through a VoIP server It supports per port speed dial lists and system speed dial lists to enable quick dialing to frequently accessed numbers Also various call features can be individually configured for each port to different destinations With support to configure IP settings manually or use DHCP or PPPoE the DIV 140 can work in different environments Also NTP is supported with standard time zone configuration to keep the device time in sync wit
40. oes off before the call history is saved to flash Also due to limitation of memory only most recent 100 calls are stored in memory D Link DIV 140 User Guide 39 Port Status Port Port Type Cable Status Hook Status Registration Status Call Status Disconnect Port Status Here you can see the status information like registration status hook status call status cable status etc about each port The table has following columns as explained below This is the port number of device This column displays the type of port Indicates whether the cable is connected to the FXO port or not Whether the port is off hook busy or on hook idle is displayed in this column This column shows Registered if the registration for this port is successful with VoIP server and it shows Not Registered if the registration is not done for this port or the registration has failed This column shows the call status of port It shows Idle if the port is free and not busy in any other call It shows Alert if the phone connected on port is ringing for incoming calls It shows Progress when port has made an outgoing call and is waiting for response from called party It shows Connected if the port is in call This button can be used to disconnect the active call It is active only when the Call Status is not Idle The page automatically refreshes periodically You can also click on REF
41. of the two fields and click the Update button to apply the changes At any time you can click on the Cancel button to discard the changes Delete Click on the Delete icon to remove the existing speed dial entry Add New To add a new speed dial entry the Phone Number text box should be empty Click on the Cancel button if it is not empty Enter a valid phone number and select a destination from drop down menu and click on the Add button to create new speed dial entry Phone Number This speed dial entry can be accessed using this number Destination This is the drop down menu of configured destinations Select a destination entry for this speed dial configuration D Link DIV 140 User Guide 33 Login Configuration Type Username Old Password New Password Retype New Password Login Configuration Two levels of privilege are supported Administrator level and User level The privilege level is identified based on username and password entered while logging into the web UI The Administrator privilege can edit all the fields on all pages perform software upgrade configuration upload and download restore factory settings modify both user and admin username and passwords and save the changes The User privilege can just view the field configuration on all pages and only editing of user level username and password is allowed The APPLY and CANCEL buttons are disabled on all pages and nothing happens when u
42. point the destination to one of the configured hunt groups Example Say it is required that if customer dials help desk number say 9901 then call should be established with the first free port in that case add a destination entry with name Help Desk pointing to hunt group of all ports and add a ACR entry with prefix as 990 pointing to this destination Here the phone numbers of ports are 9901 9902 etc 4 VoIP Number VoIP Server Select this to point the destination to a particular endpoint number which is registered on same VoIP server as configured on this device Example Say if Albert using port 1 requires that as soon as he goes off hook the call should be established with Peter phone number 6500 registered on same VoIP server then add a destination with name as Peter with type as VolP number 6500 and in port configuration enable hotline for port 1 to this destination 5 Forward to VoIP Server Select this to point the destination to configured VoIP Server This helps in inter office communications Example Say it is required to forward all calls starting with 1303 to VoIP server then add a destination with name as VoIP Server of type forward to VoIP server and in ACR add entry to direct all calls starting with 1303 to this destination 6 VoIP End Point This can be used to configure the destination to make calls to other SIP clients without going through the configured SIP server This feature does not require the
43. pter Installation This section will explain how to connect your DIV 140 device to your network Requirements The following items are required to configure the DIV 140 1 Electrical outlet 2 PC with a serial port connection 3 Terminal emulator program like Hyper Terminal 4 Browser to access web interface Following browsers are recommended a Internet Explorer version 6 0 and above b Mozilla version 5 0 and above c Netscape version 7 1 and above 5 VoIP Accounts or PSTN Lines D Link DIV 140 User Guide Connection A Connect the power adaptor to power port of the DIV 140 and then connect other end of power adaptor to an electric outlet B Connect the Ethernet port of the DIV 140 to an Ethernet port on your hub or switch using a CAT5 Ethernet cable C Using the provided RJ 45 to DB9 console cable connect the console port to your PC s COM port D Using telephone cables connect the FXO ports to the telephone wall jacks E Start a terminal emulator program on PC such as Hyper Terminal 115200 bps 8 bit F The power LED and Ethernet LEDs should both be illuminated D Link DIV 140 User Guide 8 Configuration Once powered on the DIV 140 will be at its default configuration parameters The default IP address of the device is 10 0 0 1 You can configure the device either through the web UI or Command Line Interface CLI In order to use a web browser to configure the device you must make sure the device
44. rs as configured in Port Configuration page are 95401 95402 78601 and 78602 and you have created two hunt groups Hunt Group 1 having 95401 and 95402 8 Hunt Group 2 having 78601 and 78602 Now add an entry in the ACR table with prefix as 9540 minimum and maximum digits as 1 strip digit as 5 and destination as the one pointing to Hunt Group 1 to route calls to first hunt group Similarly add an entry with prefix as 7860 minimum and maximum digits as 1 strip digits as 5 and destination as the one pointing to Hunt Group 2 to route calls to second hunt group The hunt groups can be managed on this page It shows the list of hunt groups which are currently configured You can add delete or modify the hunt groups A Maximum of 10 hunt groups can be created Edit Click on the Edit icon to modify the existing hunt group Delete Click on the Delete icon to remove the existing hunt group The destination table entries can point to a hunt group While deleting the hunt group if any of the destination entries are pointing to a hunt group being deleted then the destination entry will also be deleted Add New Click on the Add New button to create a new hunt group Click on Call Routing Architecture to understand how call can be routed to hunt group Group Name Enter a unique name for the hunt group It can be a maximum D Link DIV of 30 characters Add New Hunt Group Help FXO Members Select the FXO ports which should be pa
45. rt of this hunt group The selected members of a hunt group are shown highlighted Group Name To select multiple members from list press CTRL key on your keyboard and click on the member to be selected FXO Members 1 3 4 D Link DIV 140 User Guide 23 Destination Destination Table To configure various features like Phone Book Speed Dial x Call Forwarding Hotline Warmline etc first create the hunt D Link DIV Building Networks for People group if required then a destination entry should be added and then the feature can be configured Destination Table Help The destination entries can be managed on this page It shows the list of destinations which are currently configured You can add delete or modify the destination entries A Maximum of 25 destination entries can be created S No Destination Name Type Destination Edit Delete 1 Example 1 Dialed Local Port a Add New Edit Click on the Edit icon to modify the existing destination Delete Click on the Delete icon to delete the existing destination The ACR table entries Phone book speed dial etc can point to a destination While deleting the destination if any of the above is using the destination being deleted then those also will be deleted Add New Click on Add New button to create a new destination D Link DIV Click on Call Routing Architecture to understand how the destination entries are used E DE Des
46. ry Submitting A Claim The customer shall return the product to the original purchase point based on its return policy In case the return policy period has expired and the product is within warranty the customer shall submit a claim to D Link as outlined below e The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow DLink to confirm the same along with proof of purchase of the product such as a copy of the dated purchase invoice for the product if the product is not registered e The customer must obtain a Case ID Number from D Link Technical Support at 1 877 453 5465 who will attempt to assist the customer in resolving any suspected defects with the product If the product is considered defective the customer must obtain a Return Material Authorization RMA number by completing the RMA form and entering the assigned Case ID Number at https rma dlink com D Link DIV 140 User Guide 49 e After an RMA number is issued the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit and the RMA number must be prominently marked on the outside of the package Do not include any manuals or accessories in the shipping package D Link will only replace the defective portion of the product and will not ship back any accessories e The customer i
47. ry Installations or addresses with an APO or FPO Limited Warranty D Link warrants that the hardware portion of the D Link product described below Hardware will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product for the period set forth below Warranty Period except as otherwise stated herein e Hardware excluding power supplies and fans One 1 year e Power supplies and fans One 1 year e Spare parts and spare kits Ninety 90 days The customer s sole and exclusive remedy and the entire liability of D Link and its suppliers under this Limited Warranty will be at D Link s option to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid Any repair or replacement will be rendered by D Link at an Authorized D Link Service Office The replacement hardware need not be new or have an identical make model or part D Link may at its option replace the defective Hardware or any part thereof with any reconditioned product that D Link reasonably determines is substantially equivalent or superior in all material respects to the defective Hardware Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety 90 days whichever is longer and is subject to the same limitations and exclusions If a material defe
48. s for each D Link DIV call like source and destination numbers IP addresses codec used duration of call etc can also be monitored on this page In the first section of page you can apply the filter to customize call history list Select your options in Select Port and Call Call History Select Port All S Call Direction Both hd nm i Direction fields and click on GO button to see the call history S No From To Direction start Time Duration Status H EE 123 2001 Incoming 02 Dec 2005 11 31 24 00 00 18 Success for your selected filters ka 2 2001 123 Outgoing 02 Dec 2005 11 32 08 NA Failure 3 2001 123 Outgoing 02 Dec 2005 11 32 27 NA Failure In this drop down list you can choose a particular port to see Call History 4 123 2001 Incoming 02 Dec 2005 11 32 38 00 00 17 Success call log of only that port or choose All option to see call log of a Call History Records 1 40f4 1 all ports Total Duration 00 00 35 Reset Call History Here you can choose option to see only Incoming calls or Outgoing calls or calls in Both directions Incoming calls means calls received by FXO ports and outgoing calls means calls made by FXO ports The second section of page displays the call history table A maximum of 10 calls are displayed on one page the Following columns are displayed User ID of the party who has initiated the call User ID of the party who ha
49. s is useful in traversing a firewall Server Address Enter the IP address or domain name of the outbound proxy server This is the address where SIP messages will be sent Port Enter the outbound proxy server port in this field Local Port This is the port used by device to send and receive the SIP messages Default 5060 Un register at Boot Up If you enable this field the device will un register before sending registration requests for endpoints on every boot up Use DNS SRV If this feature is enabled the device uses DNS SRV records to find the port on which SIP service are running for the configured SIP domain name If it is disabled it will connect directly to the configured server port Subscribe for Message This feature will be supported in future release Waiting Indication D Link DIV 140 User Guide 22 Hunt Group Hunt Group You can group together several ports to create a hunt group e Incoming calls to any member in a hunt group are directed to D Link DIV Building Networks for People a port in the hunt group which is not in use The call is rejected only if all the ports in the hunt group are busy Hunt Group Table Helo To use this feature follow these steps S No Group Name Members Edit Delete 1 Create a hunt group There are no Hunt groups 2 Add a destination entry pointing to this hunt group 3 Create an ACR entry pointing to the destination to route the calls to hunt group Example IF the port numbe
50. s received the call Call direction with respect to selected port Incoming calls means calls received by FXO ports and outgoing calls means calls made by FXO ports This text is a link Click on this link to get details about call like source and destination IP address and ports codec used in call reason for failure FAX status etc System time when the call was started Duration of call in HH MM SS hour minute seconds format Displays status of a call If a port is in active call this field shows Not Over It shows Success if the call is over and it was successful It shows Failure if the call is over but was unsuccessful Click on direction link to see reason for failure if call status is Failure Click on buttons in the last row of table to see next or previous 10 call logs Also the last row displays the total number of calls for selected filter D Link DIV 140 User Guide 38 The third section of the page displays the total duration of calls for selected port and direction in first section of page Also you can use button Reset Call History to permanently clear the call history log from device memory Please note that after resetting the call history log it can not be restored back The call history is maintained in SDRAM and due to system limitations it is transferred to persistent storage only periodically say every 1 hour The information displayed in call history page may not be accurate if the power g
51. s responsible for all in bound shipping charges to D Link No Cash on Delivery COD is allowed Products sent COD will either be rejected by D Link or become the property of D Link Products shall be fully insured by the customer and shipped to D Link Systems Inc 17595 Mt Herrmann Fountain Valley CA 92708 D Link will not be held responsible for any packages that are lost in transit to D Link The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D Link Return shipping charges shall be prepaid by D Link if you use an address in the United States otherwise we will ship the product to you freight collect Expedited shipping is available upon request and provided shipping charges are prepaid by the customer D Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements or for which an RMA number is not visible from the outside of the package The product owner agrees to pay D Link s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements or that is determined by D Link not to be defective or non conforming What Is Not Covered The Limited Warranty provided herein by D Link does not cover Products that in D Link s judgment have been subjected to abuse accident alteration modification tampering negligence misuse faulty inst
52. select a destination from drop down menu and click on Add button to create new phone book entry Phone Number This is the number which users will dial to place call to this phone book entry Destination This is the drop down list of configured destinations Select a destination entry for this phone book configuration D Link DIV 140 User Guide 28 System Speed Dial Speed Dial Here you can manage the system speed dial entries common e to all FXO ports When any of the ports dial the speed dal D Link DIV Building Networks for People feature access code followed by speed dial number then the destination corresponding to that speed dial number entry if found will be dialed System Speed Dial Help Speed Dial Number Destination Example 1 ba Add Update Cancel This page shows the list of entries that are currently configured z You can add delete or modify the speed dial entries A Ba EC EEN 1 2135551122 Example 1 EN a maximum of 10 entries can be created Before configuring the speed dial entry the required destinations should be added in destination table Edit Click on the Edit icon to modify the existing speed dial entry The corresponding values will be loaded in the Phone Number text box and the Destination drop down list will show the current configured destination for that entry You can modify any of the two fields and click the Update button to apply the changes At any time you ca
53. ser clicks on them On this page you can modify the username and password of administrator and user based on your login privilege This is a drop down menu where you can select Admin or User privilege This field shows the current username for the selected type of privilege You can modify this field It can be a maximum of 30 characters Enter the current password for selected privilege level It can be a maximum of 30 characters Enter the new password you want to set for selected privilege level It can be a maximum of 30 characters Re enter the new password you want to set for the selected privilege level This will be checked with New Password field and only if both are exactly same the new parameters will be accepted It can be a maximum of 30 characters D Link DIV 140 User Guide Building Networks for People Login Configuration g Login Configuration DIV Type Username Old Password New Password Retype New Password Admin v admin 34 Debug Syslog Configuration The device supports logging debug messages to a Ss e server The related fields can be configured on this page 3 a F DIV Building Networks for People Debug Level Select the debug level in this drop down menu Setting it to Information or Trace will significantly increase the number of messages logged to server and increase the bandwidth used Default Error Log Server Address En
54. ter the log server IP address and port or domain name It can be a maximum of 40 characters E mail Configuration This feature will be supported in future releases D Link DIV 140 User Guide 35 Restore System Defaults Software Upgrade Server Type File Name Server Address Port Configuration Backup Configuration Restore Device Management Click on the Reset button to restore the system default values You will be asked to confirm the choice WARNING You D Link DIV will lose all configuration modifications you have made if you E continue with this option Device Management Help Restore System Defaults Software Upgrade Server Type HTTP TFTP File Name dtaupgrade ash All parameters like port phone numbers features ACR phone book speed dial entries network settings audio configuration etc will be set to system defaults Also note that the device IP will change to 10 0 0 1 and the GUI connection will be ei a B a CI Server Address 10 0 0 1 T accessible through this IP only Server Port Sofware Upgrade History It is recommended that you backup your configuration before y p y 9 Configuration Backup Backup Configuration continuing this operation Configuration Restore The device software can be upgraded by setting parameters File Name Lo o Browse in this section The service provider will either provide the upgrade files which can be extracted to ser
55. the default value This can be set to a value by which other users can access this FXO port D Link DIV 140 User Guide 31 Port Phone Book Phone Book Here you can manage the per port phone book When any of L the ports dial a number to make an outgoing call itis checked D Link DIV Building Networks for People if there is any phone book entry corresponding to that number If entry is found then the call is placed to that destination Port Phone Book Helo Port Number 1 hd Phone Number Loo o o Y Destination Example 1 pa Add New Update Cancel This page shows the list of entries which are currently configured You can add delete or modify the phone book entries A maximum of 10 entries can be created Before configuring the phone book entry the required destinations S No Phone Number Destination Edit Delete should be added in destination table a SSS Senge 4 o Edit Click on the Edit icon to modify the existing phone book entry The corresponding values will be loaded in Phone Number text box and Destination drop down menu will show the current configured destination for that entry You can modify any of the two fields and click the Update button to apply the changes At any time you can click on the Cancel button to discard the changes Delete Click on the Delete icon to remove the existing phone book entry Add New To add a new phone book entry the Phone Number text box should b
56. tination Name Enter a unique name for this destination It can be a maximum of 30 characters Destination Name Destination Local FXO Port 1 z Dialed Local FXO Port Hunt Group z VoIP Number VoIP Server Destination Type Select the type of destination in this section It can be one of the following fields Forward to VoIP Server VoIP End Paint DIDIDI DIDI 1 Local FXO port This can be used to route the calls to any particular local ports User ID Host IP or Domain Port Example Say if John using port 2 wants to forward calls to Cherry using port 3 then add new destination entry with name as Cherry pointing to port 3 and in port configuration enable call forward to this destination 2 Dialed Local FXO port Select this option to point the destination to one of the local ports which is decided dynamically based on dialed number D Link DIV 140 User Guide 24 Example If port phone numbers are 8001 8002 etc and it is required that calls starting with 91 should be directed to the local ports then add a destination entry with name as Local Destinations with destination type as dialed local FXO port And in the ACR Table add an entry with prefix as 91 and strip 2 digits pointing to this destination Now if user dials 918001 then call will end up on port 1 918002 it will end up on port 2 and so on 3 Hunt Group Select this to
57. ver s default directory or he will give the details to be filled in following fields Based on what upgrade server is running choose HTTP or TFTP The preferred method is HTTP especially when the upgrade server is in global network Enter the upgrade file name as released by the service provider Enter the IP address or domain name of machine where upgrade server is running Enter the port on which upgrade server is listening Click on Continue to start software upgrade Please note that the active calls will get disconnected after clicking on continue During the upgrade the calls won t go through During the upgrade you can not access any other links on web The upgrade status will be displayed on the web Once the upgrade is complete you can click on Home Page button on the status page to go back to normal mode The configuration file can be uploaded to PC to backup the configuration Right click press right button of your mouse on the link named Backup Configuration and select Save Target As option to upload the configuration to PC Note The parameters in this file should be modified if required with care You should not edit the tags i e the parameters in triangular brackets lt gt Care should be taken that the parameter values are in required validation range The configuration file can be restored from PC the configuration back up which was taken as in previous step to the device Click on the button named
58. y Server Enter the IP address of secondary STUN server Port Enter the secondary STUN server port in this field Default 3478 Username This specifies the username to use for authentication with a STUN server Password This specifies the password to use for authentication with a STUN server Note When STUN is enabled the Registration Timeout option on the VoIP Configuration page should be set to a value smaller than the binding inactivity timeout on the NAT Router This way the binding for the SIP local port can be kept alive TURN Configuration This feature will be supported in future release D Link DIV 140 User Guide 19 RTP Port Range QoS ToS VLAN ID User Priority Media Configuration Configure the port range to be used for RTP streaming This KA YY range should be larger than twice the maximum number of simultaneous calls as each call needs two ports RTP RTCP Range 1024 to 65535 Default 6000 to 10000 Parameters for various Quality of Service mechanisms can be set in this section These are used to prioritize the RTP packets on the network This field specifies the Type of Service value that is used for RTP packets Recommended value is 160 Range 00 to 255 Default 160 This feature will be supported in future releases This feature will be supported in future releases D Link DIV 140 User Guide D D Building Networks for People an DIV 20 Server Settings Pr

Download Pdf Manuals

Related Search

Related Contents

Hitachi CP-RX82 User's Manual  MP7 QUICK - SALUTEbuy  2 décembre 2014 - Pôle Universitaire Léonard de Vinci  MELSEC System Q – Controllori programmabili  Téléchargez la brochure sur la E  NAVIGATOR DVB-T/H USER MANUAL  Datasheet  Extron electronic 5cr Plus User's Manual  Presto 07045 barbecue  

Copyright © All rights reserved. Failed to retrieve file