Crestron electronic SMK-6X User's Manual
Contents
1. Swivel Mount Kit for TPS 6X SMK 6X e 7 Swivel Mount Kit for TPS 6X Crestron SMK 6X Customize Range Aside from the permanently installed limiting screw attached to the swivel stop plate two additional limiting screws are provided with your SMK 6X kit These screws are provided to set a custom range of swivel movement Refer to the illustrations below for their application Swivel Stop Plate with Permanent Limiting Screw lt _ TAB OF KEYED METAL WASHER STARTS SWIVEL MOTION FROM FRONT OF THE MOUNTING SURFACE 135 SIX LOCATIONS FOR ADDITIONAL LIMITING SCREWS SYMMETRIC PERMANENT LIMITING SCREW POSITIONED AWAY FROM FRONT EDGE OF MOUNTING SURFACE Swivel Stop Plate with Additional Limiting Screws TWO LIMITING SCREWS INSTALLED TO LIMIT SWIVEL TO A CUSTOM RANGE i PERMANENT LIMITING SCREW 8 e Swivel Mount Kit for TPS 6X SMK 6X Installation Guide DOC 6577A Crestron SMK 6X Resources Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X Industry Compliance As of the date of manufacture the SMK 6X has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling Further Inquiries If you cannot locate specific information or have questions after reviewing this guide please take advantage of Crestron s award winning customer service team by calling Crestron at 1 888 CRESTRON 1 888 273 7876 Y2. 95 98 Me XP Vista and WindowsNT 2000 are trademarks of Microsoft Corporation 10 e Swivel Mount Kit for TPS 6X SMK 6X Installation Guide DOC 6577A Crestron SMK 6X Swivel Mount Kit for TPS 6X This page is intentionally left blank Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X SMK 6X e 11 amp CRESTRON Crestron Electronics Inc Installation Guide DOC 6577A 15 Volvo Drive Rockleigh NJ 07647 2018617 Tel 888 CRESTRON 07 08 Fax 201 767 7576 Specifications subject to www crestron com change without notice
3. Crestron SMK 6X Swivel Mount Kit for TPS 6X Installation Guide CRESTRON This document was prepared and written by the Technical Documentation department at CRESTRON Crestron Electronics Inc 15 Volvo Drive Rockleigh NJ 07647 1 888 CRESTRON All brand names product names and trademarks are the property of their respective owners 2008 Crestron Electronics Inc Crestron SMK 6X Swivel Mount Kit for TPS 6X Contents Swivel Mount Kit for TPS 6X SMK 6X 1 Introduce do en as Mo E 1 Features and Functio cuina ia did aan 1 Specifications ci ee dais 1 Physical Description ii tie teat 2 SUD ot Teod Decenal 3 Supplied Hardware ii did 3 O o de E 3 RESQUICES ti E tbesdece sengalt tones 9 Industry Compliance ccccecccsseesseessessceescesecesecesecaeceaecsaecaeecaeeeneeeeeeaeeeseeeeeeeeesereerees 9 O A nFesbiptoesdceensgahsndeess 9 Future Updates es da 9 Return and Warranty Policies cccescsesecssecsseeseeeseeeseeeeceseeeneeeeeeeeeeseensecnaeeaeeaeceeceeeaeeeneeass 10 Merchandise Returns Repair Service ccceesceseesceesceesceeeceeeeseceseceseceeeceeeeenneeess 10 CRESTRON Limited Warranty ccccccecscessceescessceeecesecesecescesecesecaeceaecaeeceeeaeenneeees 10 Installation Guide DOC 6577A Contents e i Crestron SMK 6X Swivel Mount Kit for TPS 6X Swivel Mount Kit for TPS 6X SMK 6X Introduction Features and Functions Designed for attachment to the TPS 6X DS desktop dock
4. SS Swivel Mechanism p Tes Screws 3 08 32 Tube a 2007269 Connector Boot _ gt Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X SMK 6X e 5 Swivel Mount Kit for TPS 6X Crestron SMK 6X SMK 6X Swivel Mount Kit Installation NOTE The swivel stop plate has a permanently installed limiting screw to prevent the swivel mechanism plate from spinning continuously in one direction and tangling the cable attached to the TPS 6X DS This permanently installed limiting screw must be oriented so it is aligned with the rear of the TPS 6X DS as shown in the illustration on the following page 1 Prepare the mounting surface using the template provided with the kit The center hole diameter for the swivel mechanism tube should be 7 8 inch 2 23 cm minimum 15 16 inch 2 39 cm maximum Position the template so the edge indicated as the front edge of the table aligns with the desired front position of the touchpanel Observe the dashed line indicating the front edge of the TPS 6X DS to ensure the touchpanel will not overhang the mounting surface 2 Using the six mounting holes on the swivel stop plate as a template drill pilot holes 0 093 inch 0 24 cm minimum 0 115 inch 0 30 cm maximum in diameter and no deeper than 0 35 inch 0 89 cm Attach the swivel stop plate to the bottom of the mounting surface using the six screws provided with your kit Pass the swivel mechanism tube down through the mounting ho
5. bly Swivel Stop Plate And Screw 4504353 1 Metal Washer Keyed Swivel Stop 4506321 1 Cork Rubber Washer Custom Swivel 2017614 1 Rubber Washer Custom Swivel 2017615 1 Screw 08 32 x 3 8 Steel 2007269 3 Screw 08 32 x 1 8 Steel 2017634 2 Washer Flat Steel 7 8 A Narrow 2017633 1 Nut 7 8 14 1 15 16 Hex Diameter 2017632 1 31 64 H Steel Zinc Screw 08 8B 1 2 Pan Phil 2017784 6 Template Overlay Table Cutout 4504871 1 Installation To attach the SMK 6X Swivel Mount Kit to the TPS 6X DS and install the assembly on a suitable mounting surface refer to the following procedures NOTE The mounting surface thickness must be 3 4 inch 1 91 cm minimum to 1 3 8 inches 3 50 cm maximum using the hardware provided Preparing the TPS 6X DS 1 Remove the four screws on the TPS 6X DS as shown in the first illustration on the following page Carefully remove the rear cover Slide the grommet out of the bottom of the rear cover and cut the grommet from the cable Slide the boot up the cable away from the connector as shown in the second illustration on the following page Feed the connector then the boot and finally the full length of the cable through the bottom cutout in the base of the TPS 6X DS Install the blank grommet provided with your TPS 6X DS into place on the rear cover Replace the boot over the connector Replace the rear cover and the four screws removed in ste
6. ication other than that for which it was intended or if it has been subjected to misuse accidental damage modification or improper installation procedures Furthermore this warranty does not cover any product that has had the serial number altered defaced or removed This warranty shall be the sole and exclusive remedy to the original purchaser In no event shall CRESTRON be liable for incidental or consequential damages of any kind property or economic damages inclusive arising from the sale or use of this equipment CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party CRESTRON shall at its option repair or replace any product found defective without charge for parts or labor Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty Except as expressly set forth in this warranty CRESTRON makes no other warranties expressed or implied nor authorizes any other party to offer any warranty including any implied warranties of merchantability or fitness for a particular purpose Any implied warranties that may be imposed by law are limited to the terms of this limited warranty This warranty statement supersedes all previous warranties Trademark Information All brand names product names and trademarks are the sole property of their respective owners Windows is a registered trademark of Microsoft Corporation Windows
7. ing station Swivel mount increases security by reducing chance of theft while improving viewing convenience Base rotates 330 degrees Mounts on the desktop in a lectern or on a conference table Accommodates surface thickness from 3 4 inch 1 91 cm minimum to 1 3 8 inches 3 50 cm maximum using the hardware provided Cables route through center of assembly keeping cables completely hidden from work surface Customizable swivel range for added security and convenience Specifications Specifications for the SMK 6X are listed in the following table SMK 6X Specifications SPECIFICATION DETAILS Dimensions Height 2 64 in 6 69 cm Width 6 09 in 15 45 cm Depth 5 80 in 14 74 cm Weight 0 96 Ibs 0 44 kg Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X SMK 6X e 1 Swivel Mount Kit for TPS 6X Physical Description SMK 6X Overall Dimensions Mg 5 80 in 14 74 cm 0 44 in 1 11 cm A A 2 64 in 6 69 cm 2 e Swivel Mount Kit for TPS 6X SMK 6X Crestron SMK 6X 6 09 in 15 45 cm 0 39 in 0 99 cm Installation Guide DOC 6577A Crestron SMK 6X Setup Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X Supplied Hardware The hardware supplied with the SMK 6X is listed in the following table Supplied Hardware for the SMK 6X 15 16 Inner Diameter 1 75 Outer Diameter 0 134 Thick DESCRIPTION PART NUMBER QUANTITY Assem
8. le and stop plate 3 Slide the provided hardware up onto the swivel tube in the order indicated in the illustration on the following page NOTE The keyed metal washer 4506321 will fit onto the swivel mechanism tube in one of two orientations Orient the tab on the washer to face the front edge of the mounting surface 4 Tighten and adjust the provided nut onto the swivel tube to achieve the desired resistance on the swivel assembly s motion A flat tool such as a large flat head screwdriver may be used in the slot on the bottom of the swivel mechanism tube to hold the tube still while tightening the nut 6 e Swivel Mount Kit for TPS 6X SMK 6X Installation Guide DOC 6577A Crestron SMK 6X Installation Guide DOC 6577A Swivel Mount Kit for TPS 6X SMK 6X Swivel Mount Kit Installation Diagram TPS 6X DS Attached To Swivel Mechanism Plate m Front Of TPS 6X DS a Swivel Mechanism Tube Rear Of O a TPS 6X DS Slot In Tube ee Table Or Mounting Mounting Hole Surface Front Edge ka Side of Table or l A K E eat Mounting Surface Mounting Holes 6 In E A Screws 6 08 8B N I Swivel Stop Plate le 2017784 Swivel Stop Plate Cork Rubber Washer 4504353 2017614 Permanently Installed Keyed Metal Washer Limiting Screw 4506321 Screws 2 08 32 Rubber Washer 2017634 2017615 Flat Steel Washer 2017633 Nut 7 8 14 Steel 2017632
9. ou can also log onto the online help section of the Crestron website www crestron com onlinehelp to ask questions about Crestron products First time users will need to establish a user account to fully benefit from all available features Future Updates As Crestron improves functions adds new features and extends the capabilities of the SMK 6X additional information may be made available as manual updates These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision Check the Crestron website periodically for manual update availability and its relevance Updates are identified as an Addendum in the Download column Swivel Mount Kit for TPS 6X SMK 6X e 9 Swivel Mount Kit for TPS 6X Crestron SMK 6X Return and Warranty Policies Merchandise Returns Repair Service 1 No merchandise may be returned for credit exchange or service without prior authorization from CRESTRON To obtain warranty service for CRESTRON products contact an authorized CRESTRON dealer Only authorized CRESTRON dealers may contact the factory and request an RMA Return Merchandise Authorization number Enclose a note specifying the nature of the problem name and phone number of contact person RMA number and return address 2 Products may be returned for credit exchange or service with a CRESTRON Return Merchandise Authorization RMA number Authorized returns must be
10. p 1 Swivel Mount Kit for TPS 6X SMK 6X e 3 Swivel Mount Kit for TPS 6X Crestron SMK 6X CAUTION Use caution when cutting the grommet to prevent damage to the connecting cable Damage to this cable can result in loss of functionality in the TPS 6X Preparing the TPS 6X DS 1 of 2 Remove These Screws Using a 1 16 Allen i Wrench Rear Cover A Grommet I Cable y Remove These Phillips Head Screws Using a No 1 Phillips Screwdriver Preparing the TPS 6X DS 2 of 2 4 e Swivel Mount Kit for TPS 6X SMK 6X _ Rear Cover aN Blank Grommet Bottom Cutout In Baseplate Connector Installation Guide DOC 6577A Crestron SMK 6X Swivel Mount Kit for TPS 6X SMK 6X TPS 6X DS Assembly 1 Feed the Connector Boot and the full length of the cable through the swivel mechanism tube with the cable positioned between one of the guide pins and the rearmost screw hole as shown in the illustration below 2 Attach and secure the swivel mechanism plate to the TPS 6X DS using the provided screws 3 Pull the remaining cable slack down through the swivel mechanism tube CAUTION Ensure that the cable is not pinched at any point between the swivel mechanism plate and the base of the TPS 6X DS SMK 6X TPS 6X DS Assembly Diagram lt a TPS 6X DS y 7 Z is 4 gt A a a Swivel IN eN Mechanism Plate _ y Guide Pins Cable
11. shipped freight prepaid to CRESTRON 6 Volvo Drive Rockleigh N J or its authorized subsidiaries with RMA number clearly marked on the outside of all cartons Shipments arriving freight collect or without an RMA number shall be subject to refusal CRESTRON reserves the right in its sole and absolute discretion to charge a 15 restocking fee plus shipping costs on any products returned with an RMA 3 Return freight charges following repair of items under warranty shall be paid by CRESTRON shipping by standard ground carrier In the event repairs are found to be non warranty return freight costs shall be paid by the purchaser CRESTRON Limited Warranty CRESTRON ELECTRONICS Inc warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three 3 years from the date of purchase from CRESTRON with the following exceptions disk drives and any other moving or rotating mechanical parts pan tilt heads and power supplies are covered for a period of one 1 year touchscreen display and overlay components are covered for 90 days batteries and incandescent lamps are not covered This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer Purchasers should inquire of the dealer regarding the nature and extent of the dealer s warranty if any CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any appl
Download Pdf Manuals
Related Search