Craftsman 120V Owner's Manual
Contents
1. cords before operating inflator Repairs attempted by unqualified Any electrical wiring or repairs required on personnel can result in serious injury this product should be performed by or death by electrocution authorized service center personnel in accordance with national and local electrical codes Electrical Grounding Failure to provide Make certain that the electrical circuit to adequate grounding to this product which the inflator is connected provides could result in serious injury or death proper electrical ground correct voltage from electrocution See grounding and adequate fuse protection instructions When operating inflator outdoors use GFCI outlet HAZARD WARNING Risk to Breathing E D What Could Happen How To Prevent It The compressed air directly from your Air obtained directly from the inflator should inflator is not safe for breathing The never be used to supply air for human air stream may contain carbon consumption In order to use air produced monoxide toxic vapors or solid by this inflator for breathing suitable filters particles from the tank Breathing these and in line safety equipment must be contaminants can cause serious injury properly installed In line filters and safety or death equipment used in conjunction with the inflator must be capable of treating air to all applicable local and federal codes prior to human consumption HAZARD WARNING Risk o2. door openers and water heaters 1 800 4 MY HOME Call anytime day or night 1 800 469 4663 U S A and Canada www sears com www sears ca Our Home For repair of carry in items like vacuums lawn equipment and electronics call anytime for the location of the nearest Sears Parts amp Repair Service Center 1 800 488 1222 U S A 1 800 469 4663 Canada www sears com www sears ca To purchase a protection agreement on a product serviced by Sears 1 800 827 6655 U S A 1 800 361 6665 Canada Para pedir servicio de reparaci n Au Canada pour service en fran ais a domicilio y para ordenar piezas 1 800 LE FOYER C 1 888 SU HOGAR 1 800 533 6937 1 888 784 6427 www sears ca www sears com Sears Registered Trademark Trademark of KCD IP LLC in the United States or Sears Brands LLC in other countries Marca Registrada Marca de Fabrica de KCD IP LLC en Estados Unidos o Sears Brands LLC in otros paises MC Marque de commerce MP Marque d pos e de Sears Brands LLC
3. Operator s Manual CRAFTSMAN 120V INFLATOR Model No 75121 i E 120 Volt 60 SCFM 30 PSI bt SS gt SN Prj 47 Safety Guidelines Assembly Operation Maintenance Troubleshooting CAUTION Read the Safety Guidelines and All Instructions Carefully Before Operating Sears Brands Management Corporation Hoffman Estates IL 60179 U S A Visit our Craftsman website www craftsman com TABLE OF CONTENTS WARRANT E cit sis font E E E 1 REPLACEMENT PARTS erenneren 1 SAFETY GUIDELINES DEFINITIONS 0000 eee eee 2 IMPORTANT SAFETY INSTRUCTIONS 2 7 GLOSSARY 234 doth apend daera d Ant tanec nnn 7 AGGCESSORIES 3 5icec2cettacc paiva tiene gehio iaai 8 ASSEMBEY a S E 8 INSTALLATION en a aa 9 OPERATION 2 strani a E A 10 12 MAINT ENANGE ieia a r a 13 TROUBLESHOOTING GUIDE 13 SPECIFICATIONS 4 25 5 enaa E a aAa aiaa 13 WARRANTY CRAFTSMAN ONE YEAR FULL WARRANTY FOR ONE YEAR from the date of purchase this product is warranted against any defects in material or workmanship Defective product will be replaced free of charge For warranty coverage details to obtain free replacement visit the web site www craftsman com This warranty does not cover the air needle which is an expendable part that can wear out from normal use within the warranty period This warranty is void if this product is ever used while providing commercial services or if rented to another person This warranty gives you specif
4. ation b gt What Could Happen How To Prevent It Unsafe operation of your inflator could Review and understand all instructions and lead to serious injury or death to you warnings in this manual or others Become familiar with the operation and controls of the inflator Keep operating area clear of all persons pets and obstacles Keep children away from the inflator at all times Do not operate the product when fatigued or under the influence of alcohol or drugs Stay alert at all times Never defeat the safety features of this product Equip area of operation with a fire extinguisher Do not operate machine with missing broken or unauthorized parts HAZARD WARNING Risk of Injury e Do not direct air stream at body e Disconnect from supply circuitry before replacing fuse SAVE THESE INSTRUCTIONS GLOSSARY Become familiar with these terms before Code Certification Products that bear one operating the unit or more of the following marks UL CUL ETL CETL have been evaluated by OSHA CFM Cubic feet per minute certified independent safety laboratories and meet the applicable Underwriters Laboratories SCFM Standard cubic feet per minute a Standards for Safety unit of measure of air delivery Branch Circuit Circuit carrying electricity from electrical panel to outlet PSIG Pounds per square inch gauge a unit of measure of pressure ACCESSORIES This unit is capable of powerin
5. ator deflator nozzles to prevent air from leaking out of inflatables with very large air inlets AEG lem Risk of Bursting Unattended tires inflatable balls inflatable toys and other inflatable items can over inflate very quickly sometimes in a matter of seconds and result in personal injury or property damage To inflate vehicle and bicycle tires 1 Place 120 Volt Inflator evenly on flat surface Connect the PVC coil air hose to the Inflator by pulling back on the quick connect coupler and inserting this onto the valve located on the end of the 1 foot rubber air hose until you hear a click to lock the PVC coil in place Connect the screw on valve to tire air valve by twisting clockwise until it is securely attached to the tire air valve Plug the power cord into a grounded 120 Volt outlet Move the On Off switch to the On position and the Inflator will begin to operate Monitor the PSI on the gauge to fill your item to desired pressure Once you have reached the desired air pressure move the On Off switch to the Off position To remove the air hose from your tire air valve twist the screw on valve counter clockwise Unplug the power cord from 120 Volt outlet Remove the PVC coil from the Inflator by pulling back on the quick connect collar and pulling away from the valve located on the end of the 1 foot rubber air hose Allow unit to cool Risk of Flying Objects Bursting Objects Over inflating tire c
6. d the maximum allowable pressure rating of attachments or inflatable items Unattended tires inflatable balls inflatable toys and other inflatable items can over inflate very quickly sometimes in a matter of seconds and result in personal or property damage Always remain in attendance when inflating tires inflatable balls inflatable toys and other inflatable items Be prepared to stop inflator when item is fully inflated sometimes in a matter of seconds WARNING Risk from Flying Objects HAZARD What Could Happen How To Prevent It The inflator air stream can cause soft tissue damage to exposed skin and can propel dirt chips loose particles and small objects at high speed resulting in property damage or personal injury Always wear ANSI Z87 1 approved safety glasses with side shields when using the inflator Never direct compressed air toward any part of the body or at other people or animals Always turn the inflator off before attempting maintenance or attaching accessories HAZARD WARNING Risk of Electrical Shock ki What Could Happen How To Prevent It Your inflator is powered by electricity Never operate the inflator outdoors when it Like any other electrically powered is raining or in wet conditions device If it is not used properly it may Never operate inflator with protective cause electric shock covers removed or damaged Always replace damaged or worn electric
7. e with an appropriate grounding plug see following instructions The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances 1 The cord set and plug with this unit contains a grounding pin This plug MUST be used with a grounded outlet IMPORTANT The outlet being used must be installed and grounded in accordance with all local codes and ordinances 2 Make sure the outlet being used has the same configuration as the grounded plug DO NOT USE AN ADAPTOR See illustration Plug _ gE Grounded Outlets Grounding Pin 3 Inspect the plug and cord before each use Do not use if there are signs of damage 4 If these grounding instructions are not completely understood or if in doubt as to whether the inflator is properly grounded have the installation checked by a qualified electrician AMZUNINCH Risk of Electrical Shock IMPROPER GROUNDING CAN RESULT IN ELECTRICAL SHOCK Do not modify the plug provided If it does not fit the available outlet a correct outlet should be installed by a qualified electrician Repairs to the cord set or plug MUST be made by a qualified electrician Extension Cords If an extension cord must be used be sure it is e a3 wire extension cord that has a 3 blade grounding plug and a 3 slot receptacle that will accept the plug on the product e in good condition e no longer than 50 f
8. eet and 16 gauge AWG or larger Wire size increases as gauge number decreases 14 12 10 and 8 AWG may also be used OPERATION Know your Inflator READ THIS OWNER S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustration with your unit to familiarize yourself with the location of various controls and adjustments Save this manual for future reference On Off Switch Power Cord gt High Flow Inflator Deflator Adaptor Three Lous to ZI used with the High Flow Inflator Deflator Adaptor Description of Operation On Off Switch Used to turn Inflator on and off Pressure Gauge Gives the pressure reading in PSI Screw on Valve Used with standard tire valves and with accessories included with Inflator Air Needle Attaches directly to the screw on valve to inflate sport balls High Flow Inflator Deflator Adaptor Used with inflator deflator nozzles this adaptor attaches directly to the screw on valve to inflate or deflate air mattresses small boats inflatable toys and other items that require a large volume of low pressure air Pressure Gauge Ine 4 a 120 Volt 60 SCFM 30 PSI F Mo Quick Connect Coupling 1 foot rubber air hose Zj A PVC Coil Air Hose Gomes Screw on valve Presta Valve 6 lt Adaptor at Ring Air Needle Inflator Deflator Nozzles Used with High Flow Inflator Deflator Adaptor Seal Ring Used with infl
9. f Burns of What Could Happen How To Prevent It Touching exposed metal such as the Never touch any exposed metal parts on inflator head or outlet tubes can resultin inflator during or immediately after operation serious burns Inflator will remain hot for several minutes after operation Do not reach around protective shrouds or attempt maintenance until unit has been allowed to cool HAZARD E WARNING Risk from Moving Parts Pir What Could Happen How To Prevent It Moving parts such as the pulley Never operate the inflator with guards or flywheel and belt can cause serious covers which are damaged or removed injury if they come into contact with you your clothing loose hair or jewelry Attempting to operate inflator with Any repairs required on this product should damaged or missing parts or attempting be preformed by authorized service center to repair inflator with protective shrouds personnel removed can expose you to moving parts and can result in serious injury HAZARD WARNING Risk of Falling Y What Could Happen How To Prevent It An inflator can fall from a table Always operate inflator in a stable secure workbench or roof causing damage to position to prevent accidental movement of the inflator and could result in serious the unit Never operate inflator on a roof or injury or death to the operator other elevated position HAZARD WARNING Risk of Unsafe Oper
10. g the following Accessories Accessories included with your Inflator Air Needle Used to inflate sports balls High Flow Inflator Deflator Adaptor with Presta Valve Adaptor Used to inflate three nozzles and seal ring Used to inflate high performance bike tires or deflate air mattresses small boats inflatable toys and other items that require large volume of low pressure air ASSEMBLY Contents of Carton To Remove Inflator from Carton e 1 Inflator equipped with rubber air 1 Grasp handle and lift the Inflator out of the hose and pressure gauge carton e PVC Coil Air Hose with built in Screw 2 Remove all packaging from Inflator and on valve discard e 1 Inflation Accessory Kit 1 Air Needle 1 Presta Valve Adaptor 1 High Flow Inflator Deflator Adaptor with three nozzles and seal ring INSTALLATION HOW TO SET UP YOUR UNIT Location of the Inflator Locate the Inflator in a clean dry and well ventilated area The Inflator pump and housing are designed to allow for proper cooling The ventilation openings on the Inflator are necessary to maintain proper operating temperature Do not place rags or other containers on or near these openings GROUNDING INSTRUCTIONS Risk of Electrical Shock In the event of a short circuit grounding reduces the risk of shock by providing an escape wire for the electric current This Inflator must be properly grounded The Inflator is equipped with a cord having a grounding wir
11. ic legal rights and you may also have other rights which vary from state to state Sears Brands Management Corporation Hoffman Estates IL 60179 REPLACEMENT PARTS If you need to replace any inflation accessories call this number and ask for Customer Service 1 800 874 5771 SAFETY GUIDELINES DEFINITIONS This manual contains information that is important for you to know and understand This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS To help you recognize this information we use the symbols below Please read the manual and pay attention to these sections ADNE Indicates an imminently Key Nene XH Indicates a potentially hazardous hazardous situation which if not avoided situation which if not avoided may result in minor or will result in death or serious injury moderate injury AAEN Indicates a potentially ey Neale H Used without the safety alert symbol hazardous situation which if not avoided indicates a potentially hazardous situation which if not could result in death or serious injury avoided may result in property damage IMPORTANT SAFETY INSTRUCTIONS B SAVE THESE INSTRUCTIONS IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT AA em Some dust created by power sanding sawing grinding drilling and other const
12. imes Do not operate the Inflator in wet or damp areas Operate the Inflator only with the attachments that are included USE SAFETY GLASSES Also use face or dust mask if operation is dusty Household use only This product must be grounded In the event of an electrical short circuit the grounding reduces the risk of electric shock by providing an escape wire for the electric current This product is equipped with a cord having a grounding wire with an appropriate grounding plug The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances e Check with a qualified electrician or serviceman when the grounding instructions are not completely understood or when in doubt as to whether the product is properly grounded Do not modify the plug provided if it does not fit the outlet have the proper outlet installed by a qualified electrician 2 IMPORTANT SAFETY INSTRUCTIONS Morad Save these instructions e 5 S Improper operation or maintenance of this product could result in serious injury and property damage Read and understand all warnings and operation instructions before using this equipment e To reduce risk of electric shock do not expose to rain Store indoors e Household use only HAZARD A i M WARNING Risk of explosion or fire A What Could Happen How To Prevent It It is normal for electrical contacts Always opera
13. ls with no initial air will fill in less than 10 seconds Watch sports balls carefully while filling do not overfill AAAGH Risk of Bursting Too much air pressure causes a hazardous risk of bursting Check the manufacturer s maximum pressure rating for objects being inflated Carefully follow instructions 2 High Flow Inflator Deflator Adaptor For larger inflatable items you may wish to use the High Flow Inflator Deflator Adaptor as follows 1 Connect the screw on valve to high flow inflator deflator adaptor as shown Twist the screw on valve clockwise until it is securely attached Choose nozzle to be used to inflate or deflate NOTE The seal ring may be used with any of the nozzles to prevent air from leaking out of inflatables with very large air inlets Insert nozzle thru seal ring as shown The high flow inflator deflator adaptor has an inflation outlet and deflation outlet Attach the nozzle to the preferred outlet NOTE Inflation and Deflation are marked at outlets Inflation Position Deflation Position 4 Insert nozzle into inflatable and start inflator NOTE If inflatable is not getting firm enough place thumb over the deflation outlet to allow air to go directly into the inflatable AAOH Risk of Bursting DO NOT over inflate Keeping thumb over Deflation outlet could cause inflatable to over inflate Use caution when placi
14. ng thumb over Deflation outlet 12 MAINTENANCE Cleaning 1 Turn the On Off switch to Off and unplug the cord 2 Wipe exterior plastic and metal parts clean using damp cloth Do not get moisture or water into interior moving parts 3 Any other servicing should be performed by a qualified service representative TROUBLESHOOTING AAG em Risk of Unsafe Operation Voltage sources moving parts or compressed air sources are exposed when repairing the inflator Personal injury can occur Unplug the inflator before attempting the repairs PROBLEM CAUSE CORRECTION Motor will not run Circuit breaker tripped 1 Check for low voltage problem 2 Disconnect the other electrical appliances from circuit or operate the inflator on its own branch circuit Extension cord is wrong Check the extension cord length or gauge Faulty motor Contact 1 800 874 5771 SPECIFICATIONS Model No 75121 120 VAC 60Hz 1 1A 60 SCFM 30 PSI Get it fixed at your home or ours Your Home For troubleshooting product manuals and expert advice managemylife www managemylife com For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold it For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage
15. ould cause the tire to burst or the screw on valve to pop off the valve stem and become a projectile Use a tire pressure gauge to ensure an accurate tire pressure reading because the pressure gauge on the unit is for general reference only 2 9 11 OPERATION To inflate sports ball air mattress rubber raft etc 1 Place 120 Volt Inflator evenly on flat surface Connect the PVC coil air hose to the Inflator by pulling back on the quick connect coupler and inserting this onto the valve located on the end of the 1 foot rubber air hose until you hear a click to lock the PVC coil in place Select the appropriate inflation accessory and screw onto end of the PVC coil screw on valve Plug the power cord into a grounded 120 Volt outlet NOTE For instructions on how to use High Flow Inflator Deflator Adaptor at this point see the next page Insert the inflation accessory into desired item you are inflating Move the On Off switch to the On position and the Inflator will begin to operate Inflate your desired item to the correct pressure and move the On Off switch to the Off position Remove inflation accessory from screw on valve Unplug the power cord from 120 Volt outlet Remove the PVC coil from the Inflator by pulling back on the quick connect collar and pulling away from the valve located on the end of the 1 foot rubber air hose 10 Allow unit to cool ANSI eH Risk of Bursting Most sports bal
16. ruction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e lead from lead based paints e crystalline silica from bricks and cement and other masonry products e arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment always wear MSHA NIOSH approved properly fitting face mask or respirator when using such tools When using air tools basic safety precautions should always be followed to reduce the risk of personal injury e This Inflator is designed to inflate car tires bike tires ATV tires sports equipment air mattresses beach toys and other inflatables Do not use for any purpose other than inflating If you do so bodily harm or personal injury can occur Caution allow inflator to cool down 10 minutes after each 10 minutes of continuous operation After using turn off power The Inflator is not a toy Keep away from children at all times Do not carry Inflator by the air hose or power cord as damage may occur Do not leave the Inflator unattended while in operation Do not overinflate Please follow the manufacturer s instructions for the item you are inflating Keep the Inflator away from flammable areas liquids at all t
17. te the inflator in a well within the motor to spark ventilated area free of combustible materials gasoline or solvent vapors If electrical sparks from inflator come Store flammable materials in a secure into contact with flammable vapors location away from inflator they may ignite causing fire or explosion Restricting any of the inflator Never place objects against or on top of ventilation openings will cause serious inflator Operate inflator in an open area at overheating and could cause fire least 12 inches away from any wall or obstruction that would restrict the flow of fresh air to the ventilation openings Operate inflator in a clean dry well ventilated area Do not operate unit in any confined area Unattended operation of this product Always remain in attendance with the could result in personal injury or product when it is operating Always property damage To reduce the risk disconnect electrical power by moving of fire do not allow the inflator to on off switch to the off position and operate unattended unplug the power cord WARNING Risk of Bursting HAZARD M What Could Happen How To Prevent It ATTACHMENTS amp ACCESSORIES Exceeding the pressure rating of air operated accessories tires inflatable balls and other inflatables item can cause them to explode or fly apart and could result in serious injury Follow the equipment manufacturer s recommendation and never excee
Download Pdf Manuals
Related Search