Cornelius P/N 629087002 User's Manual
Contents
1. Cornelius REMCOR IMI CORNELIUS REMCOR INC 500 REGENCY DRIVE GLENDALE HEIGHTS IL 60139 2268 Telephone 800 551 4423 Facsimile 800 519 4423 INSTALLATION INSTRUCTIONS FOR ICEMAKER ADAPTER KIT P N 629087002 AND P N 629087003 For Hoshizaki Model Series KM KML 200 250 400 450 500 600 630 650 Kit Part No Dispenser Model 629087002 DF ED150 6 Valve 22 inches wide 629087003 DF ED 150 8 Valve 24 1 2 inches wide Table 1 Loose Shipped Parts 620034802 Adapter Lid 629087002 Kit 1 620034902 Adapter Lid 629087003 Kit 620034808 Manual Ice Fill Cover 629087002 Kit 620034901 Manual Ice Fill Cover 629087003 Kit 3 22127 Bracket Mounting 620701601 Screw Sheetmetal No 10 by 1 2 Long 70209 Thumbscrew No 8 32 by 3 8 inch Long 1 2 5 10 Label Disconnect P ower Before Cleaning CAUTION Disconnect electrical power to dispenser before proceeding with this installation gt 1 Unpack kit Make sure all parts in Kit are present and in good condition 2 Position the adapter lid on the Dispenser flush with the rear of the cabinet as shown in Figure 1 3 Seal to top of the Dispenser adapter lid as follows A Locate the Icemaker flush with the rear of the lid and centered for 24 1 2 inches wide Dispenser as shown in Figure 1 Run a bead of RTV on the lid inside the perimeter of the Icemaker base outline s2. Mount the bin thermostat to the bracket item 7 provided with the kit as shown in Figure 2 D Using the thumbscrews from step B preceding secure the kit bracket bin thermostat assembly from step C preceding to the same ice drop area position The purpose of this kit bracket is to lower the bin thermostat for proper filling of the ice storage bin Replace the Icemaker front panel 8 Install the caution label item 10 on the manual fill cover item 2 and secure the cover to the adapter lid with the No 8 32 thumbscrew 9 The is ready for operation NOTE Bin Thermostat must not interfere with the agitator rotation 620917305 2 DETAIL A S ICEMAKER 9 LOCATE ICEMAKER FLUSH WITH REAR OF ADAPTER LID AND CENTERED ON LID DRILL 147 HOLES USING BOTTOM OF SLOTTED HOLES SZ AS TEMPLATE La lt 2 PLACES SEAL ICEMAKER TO ITEM 1 WITH ITEM 6 RTV 10 SEE DETAIL FLUSH W SIDES OF LID 1 5 16 FIGURE 1 620917305 ICEMAKER WITH FRONT ee PANEL REMOVED SEE DETAIL ey ADAPTER LID WITH MANUAL FILL COVER REMOVED J DETAIL A ICEMAKER RIGHT SIDE WALL 620917305 ICEMAKER BIN T STAT THUMBSCREW ICEMAKER BIN T STAT
3. WHITE PLASTIC MOUNTING BRACKET FIGURE 2
4. o that the Icemaker will set on the RTV IMI Cornelius Inc 1 September 1999 Rene 620917305 Setthe Icemaker onto the lid Note If installing the Icemaker from front of the Dispenser use a length of 3 4 inch diameter or larger PVC pipe as a roller to slide the Icemaker over the front drip flange of the Dispenser lid C Wipe away any excess RTV 4 Using the slotted holes in the adapter lid as a template drill four 4 147 diameter holes No 26 drill into the Dispenser cabinet see detail A of Figure 1 Use extreme care not to drill into the ice storage bin Secure the lid to the Dispenser with four 4 No 10 sheetmetal screws 5 Install lcemaker mounting brackets two 2 as shown in Figure 1 Using the brackets as templates drill 147 inch diameter holes into the cabinet and the adapter lid Use extreme caution not to drill into any Icemaker components condenser tubing etc Secure the brackets to the Icemaker cabinet with the No 10 sheetmetal screws provided in the kit 6 Follow the Icemakers Manufacturer s instructions to complete installation of the Icemaker 7 IMPORTANT The bin thermostat bracket item 7 must be installed see Figure 2 in order to pre vent overfilling the ice storage bin A Remove the Icemaker front panel B Locate the bin thermostat on the lower right side wall of the ice drop area and remove the two 2 thumbscrews that hold the bin thermostat in place
Download Pdf Manuals
Related Search