Cornelius P/N 620032802 User's Manual
Contents
1. Cornelius Incorporated 500 Regency Drive Ornelis Glendale Heights IL 60139 gt REMGOR Facsimile 630 980 8511 INSTALLATION INSTRUCTION ICEMAKER ADAPTER KIT P N 629085001 This Adapter Kit P N 629085001 is for the following Units Dispenser Model Model ED200 250 Wilshire WCC500 700 Table 1 Adapter Kit Parts 70188 Thumb Screw 8 32X3 8 in Long 7 620913501 Installation Instructions CAUTION Disconnect electrical power from the Dispenser before attempting to install this Kit 1 5 ES ea gt 1 Remove merchandiser from the Dispenser by lifting up on both the right and the left sides to disengage the merchandiser from slots in the Dispenser cabinet Tilt the merchandiser forward from the top and lift off NOTE Disregard step 2 if the ice diverter has been factory installed 2 Refer to Figure 4 for the following A Remove the ice chute cover snap fit and ice chute 4 nuts B Remove the gate restrictor and discard Install the ice diverter as shown D Replace the ice chute and cover 3 Refer to Figure 3 for adjusting the automatic agitation timer A Loosen rotate the center mounting screw that secures the white reflector panel electrical control box cover in place and lower the cover to expose the automatic agitation timer Adjust the timer to 2 seconds ON and 1 hour OFF as shown in Figure 3 C Reinstall t2. of the icemaker including the bin thermostat 10 Secure the manual ice fill cover in position on the lid over the rear hopper access opening with the thumb screw item 6 Note that the gasket should be compressed to form a seal against the icemaker cabinet with the cover secured in position 620913501 2 DRILL 136 DIA HOLES USING BOTTOM OF SLOTTED HOLES AS A TEMPLATE DETAIL A ENLARGED of 5 MI RO ca DETAIL FIGURE 1 3 620913501 FRONT OF ICEMAKER FLUSH WITH SIDE OF DISPENSER 14 1 2 25 a x 0 RUN A BEAD OF RTV INSIDE THE PERIMETER OF THE gt 9 ICEMAKER OUTLINE ON THE LID FIGURE 2 620913501 4 REFLECTOR PANEL E BOx COVER IN DOWN POSITION ON OFF CHART FOR TIME SETTING REF FIGURE 3 5 620913501 STORAGE HOPPER GATE MOUNTING PLATE FLANGE EXTENDS INTO STORAGE HOPPER THROUGH GATE OPENING RTV TO THIS SURFACE TO SEAL TO HOPPER GATE MOUNTING PLATE ICE DIVERTER P N 15484 ICE CHUTE ASKET LAT WASHER O FIGURE 4 620913501 6
3. he white reflector panel and the merchandiser IMI Cornelius Inc 1998 REV A S NOTE Disregard steps 4 5 and 6 if the Dispenser has the icemaker adapter lid factory installed 4 Remove the plastic ice storage hopper lid and discard 5 Place the lid assembly supplied with the kit on top of the Dispenser and position it flush with the back and sides of the Dispenser as shown in Figure 1 6 Using the slotted holes in the lid as a template drill four 136 diameter 29 drill size holes at the bottom of the slots see Figure 1 detail A into the Dispenser cabinet Use care not to drill into the ice storage hop per Fasten the cover to the Dispenser with four 10 sheet metal screws two on each side 7 Seal the icemaker to the Dispenser lid as follows See Figure 2 A Runa bead of RTV around the opening in the lid and inside the perimeter of the icemaker outline so that the icemaker will set on the RTV Setthe icemaker onto the lid and position it as shown in Figure 2 C Wipe away any excessive RTV 8 Install the icemaker mounting brackets item 2 as shown in Figure 2 Using the brackets as a template drill 136 diameter 29 drill size holes into the icemaker cabinet and the Dispenser lid item 1 Use care not to drill into any icemaker components condenser tubing etc Secure the brackets using the 10 sheet metal screws provided 9 Follow the icemaker manufacturer s instructions to complete the installation
Download Pdf Manuals
Related Search