Cornelius P/N 620028801 User's Manual
Contents
1. IMI CORNELIUS REMCOR INC 500 REGENCY DRIVE GLENDALE HEIGHTS IL 60139 2268 Telephone 800 551 4423 Facsimile 800 519 4423 INSTALLATION INSTRUCTIONS FOR ED150 8V STYLE LID KIT P N 629084002 AND 629084009 THIS K STYLE KIT APPLIES TO THE FOLLOWING ICE MAKERS Ice Maker Width AC and WC Cornelius 322 522 22 in Table 1 Loose Shipped Parts 0 l se ens 14 November 1999 Cornelius Inc 1999 620918802 10 11 12 13 14 15 16 17 Unpack kit Place INSULATION STRIP Item 12 over studs on the baffle and Insert baffle assembly into the adapter lid Place two 2 sealing cap washers item 9 over studs and two 2 NYLON WASHERS item11 then fas ten in place with two 2 ACORN NUTS item 8 Set ice maker lid on the top of the dispenser Using the slotted holes in the lid as template drill four 4 140 in diameter 9 64 in holes at the bottom of the slots see detail A of Figure 1 Use extreme care not to drill into the hopper Fasten the lid to the dispenser with four 4 8 sheet metal screws two on each side Seal the ice maker to the top of the dispenser as follows A Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so that the ice maker will set on the RTV Setthe ice maker onto the lid and position it as required C Wipe a2. e bare capillary tube The bin stat will allow the ice machine cycle to complete and harvest ice then the machine will shut down If the acorn nuts interfere with the positioning of the plastic manual fill cover it may be necessary to make small notches in the cover to clear the acorn nuts NOTE Bin Thermostat must not interfere with the agitator rotation 620918802 2 ICEMAKER VIEW ENLARGED LE 8 PLCS DRILL 9 64 140 DIA 2 HOLES USING BOTTOM OF SLOTTED HOLES 4 PLCS AS TEMPLATE gt 2 PLCS VIEW A FIGURE 1 DISPENSER ASSEMBLY 3 620918802 BAFFLE AND CAPILLARY AS SHOWN IN PLACE DETAIL 2 FIGURE 2 BAFFLE 620918802 1 500 y SPLIT 25 in LONG PLASTIC SLEEVING ICE MAKER GROMMET HOLE 6 in BARE CAP TUBE PULL 25 in OF CAP TUBE OUT OF ICE MAKER DO NOT STRAGHTEN S CLIP FIGURE 3 CAPILLARY TUBE LOCATION 5 620918802
3. way the excess RTV Drill 9 64 in diameter holes into the ice maker cabinet using the bracket as a template Use extreme care not to drill into any ice maker components condenser tubing etc Secure the brackets using the screws provided Mount BIN STAT KIT item 17 as instructed except for the bin stat capillary tube mounting Pull 32 inches of capillary tube out of bottom of the ice maker Slit and place VINYL TUBING item 16 over the capillary tube leaving 6 inches of bare capillary tube exposed between capillary S bend and vinyl tubing Assemble two 2 NYLON CLAMPS item 15 to the back side of the ICE BAFFLE item 10 with two 2 SCREWS item 14 and ACORN NUTS item 8 Do not overtighten Route capillary tube around baffle as shown in Figure 2 and Figure 3 Position two 2 NYLON CLAMPS item 15 on studs of ICE BAFFLE item 10 and two 2 NYLON WASH ERS item 11 on studs as shown Place plastic insulation strip over the studs and insert baffle assembly into the bladder lid Place two 2 SEALING WASHERS item 9 over studs and fasten in place with four 2 ACORN NUTS item 8 Route and form capillary as shown in Figure 2 and Figure 3 Tighten two 2 plastic clamps 8 32 X 3 8 in screws to hold capillary tube in place Turn bin stat adjustment screw to the right clockwise until it stops then turn adjustment screw to the left counterclockwise 1 8 turn Verify the bin stat is working by holding ice on th
Download Pdf Manuals
Related Search