Cornelius ED 150 User's Manual
Contents
1. great ly reducing the efficiency of both the dispenser and ice maker 5 Fasten the lid to the dispenser with four 4 8 sheet metal screws item 6 two on each side 6 Seal the ice maker to the top of the dispenser as follows A Remove the ice maker front panel B Position the ice maker base on the gasket item 7 located on the lid assembly IMPORTANT Do not slide the ice maker into position on the lid C Lift and set the ice maker base onto the lid to avoid damaging the gasket seal 7 Install the brackets item 5 on either the rear corners or on the back of the ice maker using the brackets as a template Use care not to drill into any ice maker components condenser tubing etc or into the ice hop per Be sure to overlap the lid assembly with the brackets installing screws in both the lid assembly and ice maker 8 Install the wireform bracket supplied with the bin stat kit item 4 through the 5 8 diameter hole in the bottom of the ice maker wrapping the eye of the wireform over the stud near the hole in the ice maker and secure with the 8 32 nut provided Figure 3 Feed the bin stat cap tube through the hole to the end of the wireform bracket and wrap the tube around the end of the bracket several times insuring that the tube is secure Note The bin stat must not interfere with the agitator rotation not be in the path of the ice falling from the ice maker If so bend the bracket out of the way 9 Apply the label2. E 1030 1230 30 DUAL CURTAIN ICE MAKERS Peper _ Gm Black Gray Gray Black Gray kitNumber __ 6290879427 62087945 620087946 629087943 62008734 _ 6 Screw Mounting 7017 o my me IMI Cornelius Inc 2001 03 January 13 2002 Revision D 620919549 7 Gasket 620050102 620050102 620050102 620050102 620050102 IMPORTANT For DF ED300 models adjust the automatic agitation timer located in the dispenser s electrical control box to 5 seconds on 20 minutes off Access to the timer is provided by removing the merchandiser upper front panel 1 Unpack kit Refer to Figures 1 and 2 for component detail 2 Insert the ice baffle item 3 into the lid assembly item1 Figures 1 IMPORTANT The baffle prevents ice from over filling the manual fill area during agitation dispensing with a full storage bin and forcing the manual fill cover off 3 Place the sealing washers item 10 over the studs and flat washers item 11 then fasten in place with the nylon acorn nuts item 9 4 Set the lid assembly onto the dispenser Using the slotted holes on the side of the lid as a template drill four 4 9 64 diameter holes at the bottom of the slots Figure 2 Note Use extreme care not to drill into the hopper Use a drill stop to ensure that the drill bit does not penetrate deeper than 1 4 past the sheet metal Failure to do so could result in a hole in the hopper
3. IMI CORNELIUS INC e One Cornelius Place Anoka MN 55303 6234 Telephone 800 238 3600 Facsimile 763 422 3246 INSTALLATION INSTRUCTIONS DF ED XXX LID KITS FOR THE FOLLOWING ICE MAKERS CORNELIUS XTREME SERIES 322 522 330 530 630 830 1030 1230 Dispenser ED 100 150 Black Black Black Black Black _ pe eee et ee ee ek Gray Gray Gray Gray Gray aD ee es eee 11 Nylon Washer _ 621701903 2 4 ornelius Inc 2001 03 January 13 2002 Revision D 620919549 ho lt A Co N e N Oo Co N e N Q amp gt olo D g lt g lt 5 x 2 Uic o x 6 gt gt 5t 3 3 e e o o Ge tery Gray Gray Gray Gray Gray Kit Number 620087932 620087931 929087930 020087929 629087928 feomponents T en KITS FOR USE WITH CORNELIUS XTREME 330 530 630 830 30 SINGLE CURTAIN ICE MAKERS Dispenser ED 2XX DF 2XX ED 2XX ED 300 DF ED 300 Black Gray Gray Black Gray Kit Number 629087927 629087925 629087922 629087926 629087924 Screw Mounting 27 68 10 Sealing Washer 620701901 620701901 620701901 620701901 620701901 11 Nylon Washer 621701903 621701903 621701903 621701903 621701903 KITS FOR USE WITH CORNELIUS XTREM
4. item 8 on the front of the cover IMI Cornelius Inc 2001 03 January 13 2002 Revision D 620919549 11 10 SCALE 0 500 oo 2x 10 NOTE NOT ALL PARTS ARE SHOWN FOR CLARITY FIGURE 1 PARTS IMI Cornelius Inc 2001 03 January 13 2002 Revision D 620919549 VIEW Y SCALE 0 500 DRILL 29 64 140 HOLES USING BOTTOM OF SLOTTED HOLES AS A TEMPLATE SEE VIEW Y FIGURE 2 DISPENSER ASSEMBLY NOTE ITEM 5 USE EITHER P N 620027306 OR P N 22127 IMI Cornelius Inc 2001 03 January 13 2002 ICEMAKER NOTE SET THE ICEMAKER ONTO THE GASKET DO NOT SLIDE THE ICEMAKER INTO POSITION ON THE LID P N 620027306 a See P N 620027306 5 P N 22127 2X Revision D 620919549 FROM PANEL OF ICEMARE REWOWED Foe N SEE DETAIL BiasTaT 4 WITH BINSFAT DE TA L i J SUPPORT SCALE 0 540 wOTE BE SUPPORT Ad iaQwH FIGURE 3 BINSTAT LOCATION IMI Cornelius Inc 2001 03 January 13 2002 Revision D 620919549
Download Pdf Manuals
Related Search