Cooper Lighting W/QCT1875 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS voo087c QUIET CEILING REMODEL W SQUARE TRIM LIGHTING Avoid Fire or Electric Shock Installation Instructions for qualified electricians only Install per National Electrical Code and local regulations Read Installation Instructions completely before installation Failure to follow Installation Instructions may void warranties Pre Installation Preparation 1 Check for Above Ceiling Clearance of 5 1 2 See Fig 1 2 Make 7 1 4 diameter Cutout in Ceiling See Fig 1 5 1 2 CECHA 7 1 4 Cutout Figure 1 Electrical Connection 1 Turn OFF Electrical Service 2 All appropriate electrical rough wiring should be completed 3 Connect wiring inside J Box Transformer Assembly See Fig 2 to Existing Electrical Service through Knockouts provided NOTE Single circuit cable only and or single fixture with next fixture jumper Wire single fixture or wire through with second cable to next fixture in J Box Transformer Assembly 4 Carefully insert wired J Box Transformer Assembly Flex Cable and Lamp Socket through Ceiling Cutout into available ceiling area around cutout avoiding all insulation and combustable surfaces by 3 all around RSA Lighting 7945 Orion Ave Van Nuys California 91406 Model QCT905 RM W QCT1875 Electrical Connection Con t Lamp Socket Wiring Flex Cable J Box Transformer Assy J Box Transformer Assy Front View Figure 2 Installation Of H2. ION INSTRUCTIONS Con t vyeoos7c QUIET CEILING REMODEL W SQUARE TRIM Model QCT905 RM W QCT1875 LIGHTING CDs Installation Of Housing Con t Installation Of Housing Con t 10 Carefully tuck Lamp Socket Wiring out of way inside Fixture until needed for future trim installation 11 OPTIONAL Install additional drywall zip screws into Perforated Rotational Bracket Clamp Mudding Frame to guarantee flatness before Mudd In 12 Tape and Mudd Perforated Mudding Frame until sufficiently smooth Conduit Ring Fixture Wing Nut Ceiling CROP OPO CEE OCC CI OIG SEER OR a ORSINI KELL Ceiling 8 Set Screw Wiring Access Opening Slot TY SEYE KY IIR SISSIN EOE e SSS SSSss N 3 R Figure 5 Wiring Access Door Figure 3 Inside View of Fixture Unfolded Rotational Clamp Bracket 8 Set Screw Perforated Mudding Frame Folded Rotational Clamp Bracket Figure 4 RSA Lighting 7945 Orion Ave Van Nuys California 91406 Outside View of Fixture Fixture Conduit Ring D p KAX J Box Transformer Assembly 8 Set Screw Perforated Mudding Frame Figure 6 Visit our web site at www rsalighting com 818 349 3030 800 356 3030 FAX 818 349 3031
3. ousing 1 Remove factory installed Wiring Access Door on Fixture See Fig 3 Retain Wing Nuts and Door for re installation 2 Fold three 3 Rotational Clamp Brackets tight against Fixture See Fig 4 making sure Brackets are in upper most highest threaded position See Fig 5 to accommodate largest ceiling thickness 3 Insert Fixture into Ceiling Cutout See Fig 1 rotating to orient Square Aperture to desired position relative to adjacent wall s other fixtures aperture alignments etc 4 OPTIONAL Retain orientation by installing two 2 or three 3 drywall zip screws into outer perimeter of Perforated Mudding Frame 5 Holding Fixture firm to ceiling surface drive clockwise the three 3 8 x 3 Set Screws See Fig 5 located on the underside of Perforated Mudding Frame See Fig 6 to rotate and lock the Rotational Clamp Brackets to the ceiling DO NOT overtighten the Screws or Rotational Clamp Brackets Overtightening may crack ceiling material 6 Reach inside and through Fixture Wiring Access Opening and locate Lamp Socket Flex Cable J Box Transformer Assembly See Fig 6 7 Pull Lamp Socket and Lamp Wiring into inside of Fixture See Fig 6 8 Slide Conduit Ring See Fig 6 into Slot See Fig 5 in Wiring Access Opening 9 Re install Wiring Access Door over Conduit Ring Secure with Wing Nuts removed earlier Visit our web site at www rsalighting com 818 349 3030 800 356 3030 FAX 818 349 3031 INSTALLAT
Download Pdf Manuals
Related Search