Cooper Lighting Sure-Lites EAC Exit Series User's Manual
Contents
1. IL 60007 7 98 694827C2. SURE LITES Installation Instructions For AC EAX EAC Exit Signs IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING Po NS personnel Oa READ AND FOLLOW ALL SAFETY INSTRUCTIONS Do not use outdoors Do not mount near gas or electric heaters Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized The use of accessory equipment not recommended by Sure Lites may cause an unsafe condition Do not use this equipment for other than its intended purpose 7 Some equipment covered by these instructions are approved for remote fixtures This equipment does not require a load fuse because its sophisticated solid state transfer switch is current limited Check load rating of equipment to calculate remote capability DO NOT exceed TOTAL OUTPUT RATING of equipment TRANSFER CIRCUIT will automatically shut down if overloaded s SAVE THESE INSTRUCTIONS WALL MOUNTING INSTALLATION Step 1 Step 2 Step 3 Step 4 Step 5 Extend AC power supply of rated voltage to junction box by others Leave ade quate slack Circuit should not be energized at this time Remove screw and end cap Slide exit face from exit housing for mounting access Assemble mounting strap to junction box through proper slots using screws sup plied with junction box Install 2 mounting screws part
3. ially into correct threaded hole Remove round and 2 keyhole knockouts from back exit door Insert plastic bush ing with flanged end outside into round hole Feed wires through bushing and connect power supply in accordance with fixture type and appropriate wiring diagram Note Connections must be in junction box Hang fixtures using 2 keyhole slots tighten screws CEILING OR END MOUNT INSTALLATION Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 P oo COOPER Lighting Extend AC power supply of rated voltage to junction box by others Leave adequate inches of slack Circuit should not be energized at this time Remove screw and end cap Slide exit face from exit housing for mounting access Back off canopy mounting screws to remove mounting plate Fasten to junc tion box with short legs against mounting surface through proper slots using screws supplied with junction box Remove knockout from top or end to accommodate canopy kit QE 1030 supplied Fasten canopy to exit frame using threaded bushing and nut Feed wires through exit and canopy Make connections in accordance with fixture type and appropriate wiring diagram Re install canopy with exit to mounting plate by tightening mounting screws For top mount loosen small socket plate screw and drop socket plate for mounting of canopy and feeding of wires Note Connections must be in canopy or junction box NOTE For exit with to
4. p enclosure 277V remove 2 screws from access panel Remove panel for mounting of canopy and feeding wires SURE LITES 400 BUSSE ROAD ra ier MFG PLATE CANOPY i gt gt s TOP ENCLOSURE 277V ONLY JUNCTION BOX BY OTHERS NOTE When using non metallic boxes be sure to use the proper bracket for orientation of the mounting screws similar to a 54151 box CANOPY MTG SCREW 2 MOUNTING STRAP 0 gt 0 0S v0 4 7 7 7 7 7 POIR PLASTIC BUSHING T I 2 A THREADED BUSHING O 7 7 7 z 7 7 7 2 7 7 P SCREWS 2 ACCESS PANEL SOCKET PLATE CREW Zz 7 F 7 7 Rj BACK MTG SCREW 2 ELK GROVE VILLAGE IL 60007 a EXIT HOUSING 7 98 694827C SURE LITES WIRING DIAGRAMS Singe Cire uit Wining Two Care uit Wing Listed Listed Eat Fixtures Ory Erengency Lighting Egquprment Only For connection to a single source of supply such that all lamps are simultaneously illuminated Homal Emergency Ciut ciut Power Supply Single Source ae Power Supply S With ar Gorversion Kit l l l l l l l l l l l l l l l l ll Tao So ye Power Supply a With aT Gorwersion Bit Wiring Diagrams are for fixtures with PL lamps For fixtures with incandescent lamps omit ballasts Black leads connect directly to lamps COOPER Lighting SURE LITES 400 BUSSE ROAD ELK GROVE VILLAGE
Download Pdf Manuals
Related Search