Home

Cooper Lighting QCT502-IC User's Manual

1. 2 Loosen Lock Knob inside Fixture 3 Replace Trim Mechanism and rotate Trim Mechanism to desired beam direction 4 Remove Trim Mechanism and lock rotation Lock Knob 5 Re install Trim Mechanism into Fixture by pressing firmly to seat Ball Detent Catches being careful to align Tab Alignment Feature on Trim Mechanism with Tab Alignment Feature Notch in Rotational Adjustment Ring Tab Alignment Feature Notch Rotational Adjustment Lock Knob Fixture Figure 5 Fixture Cover Removed For Clarity Visit our web site at www rsalighting com RSA Lighting 7945 Orion Avenue Van Nuys CA 91406 818 349 3030 800 356 3030 FAX 818 349 3031
2. INSTALLATION INSTRUCTIONS vooisz MINI QUIET CEILING ROUND TRIMLESS Model QCT502 IC U LIGHTING cle bus Avoid Fire or Electric Shock Fixture Mounting Con t Installation Instructions for qualified electricians only 1 Spread Hanger Bars to fit span of rafters Maximum Hanger Bar rafter Install per National Electrical Code and local regulations Read Installation Instructions completely before installation Failure to follow Installation Instructions may void warranties 2 Hammer Flanges to seat Hanger Bar Tabs in rafters See Fig 1 span 22 1 2 inches 3 Secure Hanger Bars using one 1 nail in Mounting Hole in each THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE Flange INSTALLATION CODE BY A PERSON FAMILIAR 4 Mudding Ring is sent unmounted from factory Adjust Mudding Ring to WITH THE CONSTRUCTION AND OPERATION OF e e a THE PRODUCT AND THE HAZARDS INVOLVED applicable Mounting Hole Pattern as indicated by Ceiling Thickness z Indicator Mark imprinted on Mudding Ring See Fig 2 Fixture Mounting arenes l 5 Secure Mudding Ring using four 4 8 32 x 1 2 inch Flathead Screws for 1 2 inch 5 8 inch and 3 4 inch Ceiling thickness or four 4 8 32 x Safety Cable 3 4 inch Flathead Screws for 1 inch Ceiling thickness Bracket Fixture Housi Ceiling Thickness Indicator Mark ousing 8 32 Flathead Screw Mudding Ring Mounting Hole Tab Mudding Ring Trim Mechanism Hanger Bars 3 4 Mou
3. etent Catches See Fig 3 Lamp Installation Lamp Bracket accommodates from one 1 to three 3 accessories Rapid relamping system ensures original placement of light beam direction after relamping using Tab Alignment Feature 1 Remove Trim Mechanism from Ceiling 2 Slide out Lamp and orAccessories from under Bracket Arm to remove See Fig 4 3 Replace Lamp and or Accessories as necessary 4 To ensure original light beam placement align Tab Alignment Feature on Trim Mechanism See Fig 4 amp 5 with Tab Alignment Feature on Rotational Adjustment Ring inside Fixture See Fig 5 Lamp Accessory 1 a Accessory 2 e Spring Clip X Tab Alignment Feature Trim Mechanism Figure 4 Visit our web site at www rsalighting com 7945 Orion Avenue Van Nuys CA 91406 818 349 3030 800 356 3030 FAX 818 349 3031 INSTALLATION INSTRUCTIONS CON T v90182 gt 4 R MINI QUIET CEILING ROUND TRIMLESS LIGHTING Model QCT502 IC 360 Rotational Lamp Adjustment IF LOCKING KNOB IS UNLOCKED 1 Rotate Trim Mechanism to desired lamp beam position by turning Trim Mechanism up to 360 Degrees 2 To lock positioning remove Trim Mechanism being careful not to change rotation 3 Tighten Lock Knob inside Fixture to lock Rotational Adjustment Ring See Fig 5 4 Re install Trim Mechanism into Fixture by pressing firmly to seat Ball Detent Catches IF LOCKING KNOB IS LOCKED 1 Remove Trim Mechanism from Fixture
4. nting Hole Pattern Flange Figure 1 Figure 2 Visit our web site at www rsalighting com RSA Lighting 7945 Orion Avenue Van Nuys CA 91406 818 349 3030 800 356 3030 FAX 818 349 3031 LIGHTING INSTALLATION INSTRUCTIONS CON T MINI QUIET CEILING ROUND TRIMLESS Model QCT502 IC V90182 Fixture Mounting Con t 6 Install Ceiling drywall up to Mudding Ring on Fixture so that the two 2 Mudding Frame Brackets contact inside of Ceiling See Fig 3 7 Retain Fixture to Ceiling with one 1 Flathead Screw through each of the two 2 Mudding Frame Bracket See Fig 3 8 Apply Drywall Tape and Mudding Compound to Mudding Ring overlapping Mudding Ring Flathead Screws Fixture Gap and surrounding area Feather out Mudding Compount from Mudding Ring opening to surrounding ceiling area to produce a smooth flat finish See Fig 3 Rotational Adjustment Ring Lock Knob Mudding Ring Fixture Mudding Frame Bracket Flathead Screw Ceiling Drywall Tape Mudding Compound Fixture Gap Ball Detent Catch t Trim Mechanism Figure 3 RSA Lighting Trim Installation 1 Connect Safety Cable attached to Banana Bracket on Trim Mechanism See Fig 1 amp 5 to Fixture by inserting Safety Cable through opening in Fixture and inserting Snap Hook See Fig 5 on end of Safety Cable into hole in Bracket attached to inside of Fixture Housing Cover See Fig 1 2 Install Trim Mechanism into Fixture by pressing firmly to seat Ball D

Cooper Lighting QCT502-IC User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents