Cooper Lighting IMI-597 User's Manual
Contents
1. torque values Pole Clamp 6b Attach the Pole Clamp Dual Head Attach the two 2 LOWER FLITE ARM using the six 6 3 8 16 x 0 75 screws provided as depicted in Figure 6b Do not tighten the screws completely leave approximately 1 8 to 1 4 gap between the two parts This will allow these parts to slip over the pole with no interference NOTE Pole Clamps 2 and One set of six 6 3 8 16 x 0 75 screws are not necessary for this assembly Discard if desired Fig 6b These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVvU040197 INVUE Flite INSTALLATION INSTRUCTIONS __Steet oF IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE ogee ASS RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 7a Slipping the Assembly over the Pole Single Head Slip the fixture assembly over a 4 inch diameter pole as shown in Figure 7a There is a shoulder inside the arm that will rest on the top of the pole Make wiring con2. City GA 30269 IMI 597 Avu040197 INVUE Flite INSTALLATION INSTRUCTIONS __Steet 8 or IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE eens Ma RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 4 Attach Housing to Upper Flite Arm Remove the WIREWAY PLUG from the HOUSING Move the fixture leads aside so the THREADED RODS may be accessed through the fixture HOUSING See Figure 4a Attach the UPPER FLITE ARM to the HOUSING by inserting the threaded studs into the fixture HOUSING Feed the fixture wires through the UPPER FLITE ARM Slide the HOUSING over the threaded rods and secure it with the PLAIN WASHERS LOCK WASHERS and HEX NUTS See Figure 4b Torque HEX NUTS as follows Medium Icon ICM 450 in lbs Small Icon ICS 130 in lbs A WARNING Risk of Personal Injury Wireway Plug Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values NOTE It may be helpful to use a deep sock et when installing the HEX NUTS Re install the WIREWAY PLUG into the upper Flite wireway in the HOUSING These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or mainten
3. IC CONNECTOR Swing the POWER SUPPLY TRAY up and tighten the two THUMB SCREWS Re install the REFLECTOR to the HOUSING Connect the REFLECTOR CONNECTOR to the HOUSING Swing the REFLECTOR up until it is secured by the REFLECTOR TABS You will hear an audible click when the REFLECTOR TABS have properly engaged Close the fixture DOOR See Figure 9 You will hear two audible clicks when the two BUTTON LATCHES are properly engaged Re lamping the Fixture Disconnect the power to the fixture Open the DOOR by pressing both BUTTON LATCHES at the same time Remove the lamp by grasping it close to the base and install the new lamp Close the fixture DOOR You will hear two audible clicks when the two BUTTON LATCHES are properly engaged Reflector Power Supply Tray Outer Door These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197
4. INVUE Flite INSTALLATION INSTRUCTIONS ___Sheet oF IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE 8 31 04 IMI 597 RETAIN FOR FUTURE REFERENCE General Upon receipt of fixture thoroughly inspect for any Safety This fixture must be wired in accordance with freight damage which should be brought to the attention of the national electrical code and applicable local codes the delivery carrier Compare the catalog description listed and ordinance Proper grounding is required to insure on the packing slip with the fixture label on the housing to personal safety Carefully observe grounding procedure assure you have received the correct merchandise All work should be done by an electrician WARNING Risk of Electric Shock Disconnect power at circuit breaker panel or fuse box before installing or servicing 1 Open the Door Press both BUTTON LATCHES at the same time and open the door See Figure 1 Button Latches Push to Open 2 Reflector Removal Press the two REFLECTOR TABS outward and swing the REFLECTOR down See Figure 2a and Figure 2b NOTE Disconnect REFLECTOR CONNECTOR from the HOUSING as shown in Figure 2c Reflector Tabs Fig 2a These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to sa
5. ance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197 INVUJE Flite INSTALLATION INSTRUCTIONS ME IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 5a Attach the Lower Flite Arm Single Head Attach the LOWER FLITE ARM to the UPPER FLITE ARM using the three 3 5 16 18 x 1 25 screws provided Please see Figure 5a Be careful to route the wires through and along the arm so that they will not be pinched when the arms are tightened Torque 250 in lbs NOTE To assure a safe product over time check and adjust torque to proper settings each time unit is maintenanced Lower Flite Arm A WARNING Risk of Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 5b Attach the Lower Flite Arm Dual Head Attach the LOWER FLITE ARM to the UPPER FLITE ARM using the three 3 5 16 18 x 1 25 screws provided Please see Figure 5b Be careful to route the wires through and along the arm so that they will not be pinched when the arms are tightened Torque 250 in lbs NOTE To assu
6. maintenanced Fig 8a A WARNING Risk of Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 8b Attaching the Mast and Pole Cap Dual Head Assemble the ARM MAST and POLE CAP to the fixture and arm assembly See Figure 8b Tighten the six 6 screws that clamp the arm to the pole in addition to the set screws that secure the ARM MAST and POLE CAP Torque 250 in lbs NOTE To assure a safe product over time check and adjust torque proper settings each time unit is maintenanced These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197 INVUE Flite INSTALLATION INSTRUCTIONS __steet8 oF IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE ene elite RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 9 Buttoning Up Re install the POWER SUPPLY TRAY to the HOUSING Connect the POWER CONNECTOR and OPT
7. nections at the opening at the top of the arm 7b Slipping the Assembly over the Pole Dual Head Slip the fixture assembly over a 4 inch diameter pole as shown in Figure 7b There is a shoulderinside the arm that will rest on the top of the pole Make wiring connections at the opening at the top of the arm These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197 INVUE Flite INSTALLATION INSTRUCTIONS __Steet 7 oF IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE ae soa RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 8a Attaching the Mast and Pole Cap Single Head Assemble the ARM MAST and POLE CAP to the fixture and arm assembly See Figure 8a Tighten the six 6 screws that clamp the arm to the pole in addition to the set screws that secure the ARM MAST and POLE CAP Torque 250 in lbs NOTE To assure a safe product over time check and adjust torque to proper settings each time unit is
8. re a safe product over time check and adjust torque to proper settings each time unit is maintenanced Upper Flight Arm Fig 5b with Housings 2 Lower Flight Arm 2 These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197 INVUE Flite INSTALLATION INSTRUCTIONS __Steets of IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE ogee sol RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 6a Attach the Pole Clamp Single Head Attach the POLE CLAMP to the LOWER FLITE ARM using the six 6 3 8 16 x 0 75 screws provided as depicted in Figure Ga Do not tighten the screws completely leave approximately 1 8 to 1 4 gap between the two parts This will allow these parts to slip over the pole with no interference Fig 6a A WARNING Risk of Personal Injury Fixture may become damaged and or Pee unstable if not installed properly Tighten all fixture components to their recommended
9. tisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 597 AVU040197 INVUE Flite INSTALLATION INSTRUCTIONS __Sheet2 rs IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE eet aar RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing ws ay ee Reflector Reflector Tabs Ae TN A Reflector PA Ko M Fig 2b 3 Power Supply Tray Removal Unscrew the two THUMB SCREWS and swing the POWER SUPPLY TRAY down as shown in Figure 3a Disconnect the POWE CONNECTOR and the OPTIC CONNECTOR from HOUSING See Figure 3b The POWER SUPPLY TRAY can now be lifted off the bracket DEO a e Power Connector ke SS N aoe S Optic Connector f e i i IL e UO EN rv Thumb Screws Fig 3a These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree
Download Pdf Manuals
Related Search